Dallas Semiconductor DS1135U-25, DS1135U-20-T-R, DS1135U-20, DS1135U-15-T-R, DS1135U-15 Datasheet

...
0 (0)
1 of 6 061500
FEATURES
All-silicon timing circuit
Three independent buffered delays
Stable and precise over temperature and
voltage
Leading and trailing edge precision preserves
the input symmetry
(150 mil)
Vapor phasing, IR and wave solderable
Available in Tape and Reel
Commercial and industrial temperature ranges
available; see order info table
5V operation (for 3V operation, see part
number DS1135L)
Recommended replacement for DS1013 and
DS1035
PIN ASSIGNMENT
PIN DESCRIPTION
IN1-IN3 - Input Signals
OUT1-OUT3 - Output Signals
V
CC
- +5V Supply
GND - Ground
DESCRIPTION
The DS1135 series is a low-power, +5-volt high-speed version of the popular DS1013 and DS1035.
The DS1135 series of delay lines have three independent logic buffered delays in a single package. The
device is Dallas Semiconductor’s fastest 3-in-1 delay line. It is available in a standard 8-pin DIP and
150 mil 8-pin Mini-SOIC, as well as an 8-pin, 118 mil uSOP.
The device features precise leading and trailing edge accuracy. It has the inherent reliability of an all-
silicon delay line solution. Each output is capable of driving up to 10 LS loads.
Standard delay values are indicated in Table 1. Customers may contact Dallas Semiconductor at
(972) 371-4348 for further information on custom delay values.
DS1135
3-in-1 High-Speed Silicon Delay Line
www.dalsemi.com
DS1135M 8-Pin DIP
IN2
GND
V
CC
OUT1
OUT2
OUT3
7
1
2
3
4
8
6
5
IN3
IN1
DS1135Z 8-Pin SOIC (150 mil)
1
2
3
4
7
8
6
5
IN2
GND
IN3
IN1
V
CC
OUT1
OUT2
OUT3
DS1135U 8-Pin 118-mil uSOP
1
2
3
4
7
8
6
5
IN2
GND
IN3
IN1
V
CC
OUT1
OUT2
OUT3
DS1135
2 of 6
LOGIC DIAGRAM Figure 1
PART NUMBER DELAY TABLE (t
PLH
, t
PHL
) Table 1
TOLERANCE OVER
TEMP AND VOLTAGE
(Note 2)
PART NUMBER
DELAY PER
OUTPUT
(ns)
INITIAL
TOLERANCE
(Note 1)
0°C to +70°C -40°C to +85°C
DS1135-5 5/5/5
±1.0 ns ±1.0 ns ±1.5 ns
DS1135-6 6/6/6
±1.0 ns ±1.0 ns ±1.5 ns
DS1135-8 8/8/8
±1.0 ns ±1.0 ns ±1.5 ns
DS1135-10 10/10/10
±1.0 ns ±1.0 ns ±1.5 ns
DS1135-12 12/12/12
±1.0 ns ±1.0 ns ±1.5 ns
DS1135-15 15/15/15
±1.0 ns ±1.5 ns ±2 ns
DS1135-20 20/20/20
±1.0 ns ±1.5 ns ±2 ns
DS1135-25 25/25/25
±1.5 ns ±1.5 ns ±2 ns
DS1135-30 30/30/30
±1.5 ns ±1.5 ns ±2 ns
NOTES:
1. Nominal conditions are +25°C and V
CC
=+5.0 volts.
2. Voltage range of 4.75 volts to 5.25 volts.
3. Delay accuracies are for both leading and trailing edges.
TEST SETUP DESCRIPTION
Figure 2 illustrates the hardware configuration used for measuring the timing parameters of the DS1135.
The input waveform is produced by a precision pulse generator under software control. Time delays are
measured by a time interval counter (20 ps resolution ) connected to the output. The DS1135 output taps
are selected and connected to the interval counter by a VHF switch control unit. All measurements are
fully automated with each instrument controlled by the computer over an IEEE 488 bus.
TIME DELAY
OUTIN
ONE OF THREE
Loading...
+ 4 hidden pages