Daewoo DWD-E1211W'S, DWD-E1211R'S User Manual

1.17 Mb
Loading...

Washing Machine Instruction Manual

DWD-E1211R’S/E1211W’S

INSTRUCTION MANUAL

Economic wash system

Using artificial intelligence, the washer uses minimum energy and water by selecting optimal water lever and washing time.

Low noise system

The washer minimizes the washing and spinning noises by sensing the amount of laundry.

Child-Lock

The Child-Lock system has been used to prevent children from pressing any

button to change the program during operation.

Nano-silver sterilization washing(Option)

By applying very fine silver particles on essential parts inside, the washer sterilizes up to 99.9% as is done by boiling wash.

Air bubble washing(Option)

This is an advanced technology that generates millions of air bubbles inside the drum on washing sequence, and the bubbles dissolve the detergent particles completely and cleanse all the soil in clothes gently and neatly.

CONTENTS

Page

PARTS AND FEATURES.................................................................................................................

2

WASHER SAFETY...........................................................................................................................

3

INSTALLATION INSTRUCTIONS ....................................................................................................

4

INLET HOSE CONNECTION ...........................................................................................................

5

ELECTRICAL REQUIREMENTS .....................................................................................................

6

OPERATING YOUR WASHER ........................................................................................................

7

THE FUNCTIONS OF THE CONTROL PANEL...............................................................................

9

WASHING PROGRAM...................................................................................................................

11

WASHING PROCEDURE AND SELECTION ................................................................................

12

GUIDE FOR OTHER USEFUL PROGRAMS.................................................................................

23

MAINTENANCE .............................................................................................................................

27

HOW TO CLEAN THE FILTER ......................................................................................................

28

REMOVING STAINS ......................................................................................................................

29

TROUBLE SHOOTING ..................................................................................................................

30

SPECIFICATION ............................................................................................................................

31

A NOTE TO YOU

 

Thank you for buying a DAEWOO appliance.

 

DAEWOO washers are easy to use, save time, and help you manage your home better.

 

This manual contains valuable information about how to operate and maintain your washer property and safely.

 

Please read it carefully.

 

PARTS AND FEATURES

The parts and features of your washer are illustrated on the page.

Become familiar with all parts and features before using your washer.

NOTE

The drawings in the book may vary from your washer model.

They are designed to show the different features of all models coverd by this book, Your model may not include all features.

INLET HOSE

INLET HOSE

(HOT, OPTION)

(COLD)

DETERGENT CASE

POWER CORD

CONTROL PANEL

DOOR

HOSE DRAIN

PUMP COVER

ADJUSTABLE LEG

PANEL LOWER

Accessories

Hose drain

Inlet hose

Spanner

Manual

Cap holder(3EA)

2

WASHER SAFETY

Save these instructions

Your safety is important to us.

To reduce the risk of fire, electrical shock, or injury when using your washer adhere to the following basic precautions.

Read all instructions before using your washer

Flammable fluids (dry-cleaning solvents, kerosene, gasoline, etc.) should not be used or stored in or near your washer.

Do not add flammable fluids to your wash water.These substances give off vapors that can create a fire hazard or explosion.

After starting a cycle, do not reach into the washer until all motions stop.

Do not tamper with the controls.

The appliance is not intended for use by young children or infirm persons without supervision.

If the supply cord is damaged, it must be replaced by the manufacturer, or its service agent or a similarly qualified person in order to avoid a hazard.

If the appliance is supplied from a cord extension set or electrical portable outlet device it should be positioned so that it is not subjected to splashing or ingress of moisture.

Please ...

Have only a qualified person install, repair, or replace parts on washer.

Maintain washer properly.

Protect washer from the weather and keep it where the temperature will not fall below freezing.

Do not install the washer at a place of extremely high humidity. It could cause an electric shock or a short circuit.

Connect washer to the correct outlet, electrical supply, water supply, and drain supply.

Understanding your responsibilities

Do not use chlorine bleach and ammonia or acid(such as vinegar or rust remover) in the same wash. Hazardous fumes can form.

Unplug power supply cord before attempting to service your washer.

Do not wash fiberglass material.

Small particles can stick to fabrics washed in following loads and cause skin irritation.

Do not spray water on the control panel of the washer. It could cause fire or an electric shock.

In case of the dual valve model, if you connect only cold water inlet valve, while water temperature is selected as hot or warm, there can be water leakage from unconnected water inlet valve.

This appliance must be grounded.

To avoide electrical shock, use a metal pipe for the ground connection.

3

Drain Hose

INSTALLATION INSTRUCTIONS

Removing transit bolts

1.Before operating the washer, remove the transit bolts(4ea) along with the rubber.

If the bolts are not removed, it may cause heavy vibration, noise and malfunction.

3. Close the holes with the cap holders supplied.

2.Unscrew the 4 bolts with the spanner supplied. Keep the 4 bolts and spanner for future use.

Whenever the appliance is transported, the transit bolts must be refitted.

Location of washer

• Check location where the washer will be installed. Make sure you have everything necessary for correct installation.

• Do not place or store your washer below 0°C (32°F) to avoid any damage from freezing.

• Do not place or store laundry products on top of washer at any times.

• Install the washer on the horizontal solid floor.

If the washer is installed on an unsuitable floor, it could make

Washer

 

considerable noise, vibrate severely and cause a malfunction. If the

 

washer is not level, adjust leg up or down for horizontal installation.

 

• Ventilation openings must not be obstructed by carpeting when the

Laundry

washer is installed on a carpeted floor.

• Leave some space (right & left : 2cm, rear : 10cm).

Tub

approx.

• In case of built-in installation, the distance between top of the washer

2cm

and bottom of upper plate should be at least 3mm.

 

4

INLET HOSE CONNECTION

The washer should be connected to the water mains using new hose sets and old hose sets should not be reused.

In using only one water tap or in case of only one water inlet valve, connect the inlet hose to the cold water inlet valve.

Option : Be careful not to confuse hot water inlet and cold water inlet.

For Ordinary Tap

1Pull down the collar of the

2Loosen the four screws

3Fit the water tap adapter

inlet hose to separate it

properly in order to fit into

into the water tap and

from the water tap

water tap.

tighten the four screws

adapter.

 

evenly while pushing up

 

 

the adapter so that the

 

 

rubber packing can stick

 

 

to the water tap tightly.

 

 

TAPE

4Remove the tape, and

5Connect the inlet hose to

6Connect the inlet hose

screw connector B into

the water tap adapter by

adapter of the hose to the

connect A tightly.

pulling down the collar of

water inlet of the washer

 

the hose end.

by turning it clockwise to

 

 

be fixed tightly.

Connector A

Connector B

inlet

For Screw-Shaped Tap

1Connect the inlet hose to the water tap by screwing the connector tightly.

Rubber

Connector Packing

Hose Connector

2Connect the connector inlet supplied if

Connector

inlet

Rubber

Connector Packing

Hose Connector

inlet of a washer and turn it to be fixed.

*Check the packing in the inlet

5

ELECTRICAL REQUIREMENTS

WARNING

Electrical shock hazard : Failure to follow these instructions could result in

death or serious injury.

 

 

 

Electrical earth is required on this washer

If it does not fit the outlet, have a proper outlet installed by a qualified electrician.

Don’t earth to a gas pipe.

Don’t change the power supply cord plug.

Check with a qualified electrician if you are not sure the washer is properly earthed.

Recommended earthing method

C

B

A

For your personal safety, this washer must be earthed.

This washer is equipped with a power supply cord ‘A’ having a earthing plug ‘B’. To minimize possible shock hazard, the cord must be plugged into a mating earthing-type wall receptacle ‘C’. If a mating wall receptacle is not available, it is the personal responsibility and obligation of the customer to have the proper earthed wall receptacle installed by a qualified electrician.

Drain system

Never forget to install drain hose before operating your washer.

Open the packing box, and there is a drain hose inside the drum.

Connect the drain hose to the drain outlet at the back side of the washer.

Top of laundry tub must be at least 60cm high and no higher than 100cm from bottom of washer.

When installing the drain hose to tub(sink), secure it tightly with a string.

Proper securing of the drain hose will protect the floor from damage due to water leakage.

When the drain hose is too long, do not force it back into the washer. This will cause abnormal noise.

Level adjustment

1If the washer is installed on an unsuitable floor, it could make considerable noise, vibrate and cause a malfunction.

6

2Adjust the level of washer using adjustable legs.

Please check if there is any gap between the four adjustable legs and the floor.

Turning adjustable legs by the enclosed

spanner, adjust the level of washer and make

it sure that there is no swaying of washer.

Fixing Nut

 

• After the adjustment is finished, turn the fixing

adjustable leg

nuts up tightly so that the washer maintains

 

the adjustment.

 

3Make it sure that the washer does not sway when you press down the four corners of the washer's top plate.

NOTE

There should be no swaying of washer and all the adjustable legs should stick to the floor closely.

OPERATING YOUR WASHER

To obtain the best washing results, you must operate your washer properly. This section gives you this important information.

Preparing clothes for washing

Close zippers, snaps, and hooks to avoid snagging other items.

Remove pin, buckles, and other hard objects to avoid scratching the washer interior.

Empty pockets and pull them inside out.

Turn down cuffs and turn synthetic knits inside out to avoid pilling.

Tie strings and sashes to avoid tangling.

Treat spots and stains.

(See “Removing stains” on page 21)

7

Sorting

Separate heavily soiled items from lightly soiled ones, even if they would normally be washed together.

Separate dark colors from light colors, colorfast items from non-colorfast item.

Soil (Heavy, Normal, Light) Color (White, Lignts, Darks) Lint (Lint producers, Collectors)

Separate clothes according to amount of soil. Separate white clothes from colored clothes. Wash lint producers and lint collectors separately.

Loading

Drop items into washer loosely. Items should move easily through wash water for

best cleaning and

-free results.

Load washer properly and select correct load size setting.

Overloading and selecting a setting too small for the wash load can :

-Cause poor cleaning

-Increase wrinkling

-Create excessive lint

-Wear out items faster (because of pilling)

Mix large and small items in each load. Load evenly to maintain washer balance.

An unbalanced load can make the washer vibrate during spin.

Reduce wash time when using a small load size setting. Load with only a few small items needs less wash time.

Use a large load size setting to reduce wrinkling with permanent press clothes and some synthetic knits. These items should have more room to move in the water than heavy items. (towels, jeans)

Adding detergent

1Detergent case

Pre wash

Main wash

Fabric softener

2Adding fabric softener

If desired, add measured liquid fabric softener to the softener inlet.

Pour liquid fabric softener into the dispenser using the amount recommended on the package.

Do not exceed the maximum fill line. Overfilling can cause early dispensing of the fabric softener which could stain clothes.

Do not open the detergent case when water is supplied.

Avoid pouring fabric softener directly on the clothes.

8

THE FUNCTION OF CONTROL PANEL(DWD-E1211R'S)

Press this switch to turn the power 'ON' or 'OFF'.

Operation and temporary stop is repeated as it is pressed. When you want to change program in operating; Press the 'Start/Pause' button→ Select the program that you want to change → Press the 'Start/Pause' button again.

You can select the course you want and each lamp is turned on when that course is selected.

You can select the wash course you want and each lamp is turned on when that course is selected. As this button is pressed, the wash course is selected by 'Quick Wash'(proper load amount :1~2kg)→ 'Small'(proper load amount :2~3kg)→ 'Main Wash'→ 'Pre Wash'→ 'Soak'→ 'Quick Wash' .

You can select the rinse time(s) you want and each lamp is turned on when that course is selected. As this button is pressed, the rinse time(s) is selected by '1'→ 'Rinse Hold'→ '2'→ 'Rinse Hold' →... ...→ '5'→ 'Rinse Hold'→ '1'.

You can select the spin speed you want and each lamp is turned on when that course is selected.

It can be used to pre-engage time for wash from 1 hr to 12 hrs.

It can be used to adjust water temperature according to types of the load to be washed.

As this button is pressed, water temperature is selected by Cold → 30°C → 40°C → 60°C → 95°C.

You can select the dry condition you want and each lamp is turned on when that course is selected.

Use this function when you want to protect any accident occurring from handling of washer by a child. During an operation of washer, press 'TEMP' and 'DRY' buttons simultaneously during 3 second. If this mode will be set successfully, CHL and remain time will be showen on PCB board alternately.

In Child Lock mode, no button functions except Power button.

If you want to set this mode, press 'TEMP' and 'DRY' buttons simultaneously during 3 second.

And if you want to release this mode, press 'TEMP' and 'DRY' buttons simultaneously again during 3 second.

If you want to change to the desire program, while this mode is working;

1. Press 'TEMP' and 'DRY' buttons simultaneously again during 3 second.

2.Press the 'Start/Pause' button.

3.Select the desired program and press the 'Start/Pause' buttom again.

Change the desired program

*The Child Lock mode can happen. Also, this mode

at any time and it is automatically released when operation errors when power is off.

If you want to open Door intensionally during operation, press the 'Start/Pause' button and press again 'Door unlock' button.

In this case, signal will be appeared on PCB board, then you can open Door after cooling insideTub temperature and draining water, also no button functions except Power button.

9

THE FUNCTION OF CONTROL PANEL(DWD-E1211W'S)

Press this switch to turn the power 'ON' or 'OFF'.

Operation and temporary stop is repeated as it is pressed. When you want to change program in operating; Press the 'Start/Pause' button→ Select the program that you want to change → Press the 'Start/Pause' button again.

You can select the course you want and each lamp is turned on when that course is selected.

You can select the wash course you want and each lamp is turned on when that course is selected.

You can select the rinse time(s) you want and each lamp is turned on when that course is selected.

You can select the spin speed you want and each lamp is turned on when that course is selected.

It can be used to pre-engage time for wash from 1 hr to 12 hrs.

It can be used to adjust water temperature according to types of the load to be washed.

As this button is pressed, water temperature is selected by Cold → 30°C → 40°C → 60°C → 95°C.

It can be used to do only Rinse and Spin.

Use this function when you want to protect any accident occurring from handling of washer by a child.

During an operation of washer, press 'TEMP' and 'RINSE+SPIN' buttons simultaneously during 3 second. If this mode will be set successfully, CHL and remain time will be showen on PCB board alternately. In Child Lock mode, no button functions except Power button.

If you want to set this mode, press 'TEMP' and 'RINSE+SPIN' buttons simultaneously during 3 second. And if you want to release this mode, press 'TEMP' and 'RINSE+SPIN' buttons simultaneously again during 3 second.

If you want to change to the desire program, while this mode is working;

1. Press 'TEMP' and 'RINSE+SPIN' buttons simultaneously again during 3 second.

2.Press the 'Start/Pause' button.

3.Select the desired program and press the 'Start/Pause' buttom again.

 

Change

 

the desired

 

program

* The Child Lock

be set at any time and it is automatically released when operation errors

happen. Also, this

works when power is off.

It you want to open Door intensionally during operation, press the 'Start/Pause' button and press again 'Door unlock' button.

In this case, signal will be appeared on PCB board, then you can open Door after cooling insideTub temperature and draining water, also no button functions except Power button.

10

WASHING PROGRAM

Program

Fabric type

Proper Temp.

Default data

Maximum Load

 

 

 

 

 

Normal

Colorfast garments (shirts,

40 °C

Wash: main wash

Refer to

 

night dresses, pajamas,..) and lightly

(cold,30°C, 60°C)

Rinse: 3

rating lavel

 

soiled white cottons(underwares,..)

 

Spin: 800

 

 

 

 

Temp.: 40°C

 

 

 

 

 

 

White

First check whether laundry is

95 °C

Wash: main wash

Refer to

 

machine washable. (white cotton,

(fixed)

Rinse: 3

rating lavel

 

linen, towel and sheets..)

 

Spin: 800

 

 

 

 

Temp.: 95°C

 

 

 

 

 

 

Eco-White

First check whether laundry is

60 °C

Wash: main wash

Refer to

 

machine washable. (white cotton,

(40°C)

Rinse: 3

rating lavel

 

linen, towel and sheets..)

 

Spin: 800

 

 

 

 

Temp.: 60°C

 

 

 

 

 

 

Synthetic

Polyamide, Acrylic, Polyester,..

40 °C

Wash: main wash

Refer to

 

 

(cold, 30°C, 60°C)

Rinse: 3

rating lavel

 

 

 

Spin: 800

 

 

 

 

Temp.: 40°C

 

 

 

 

 

 

Heavy Stain

Heavy soiled clothes

40 °C

Wash: pre wash

Refer to

 

(blue-jean,climbing clothes, ruck

(cold, 30°C, 60°C)

Rinse: 3

rating lavel

 

sack, sports wear,...)

 

Spin: 800

 

 

 

 

Temp.: 40°C

 

 

 

 

 

 

Wool

Machine washable woolens with pure

Cold

Wash: main wash

Refer to

 

new wool only

(fixed, in order to

Rinse: 2

rating lavel

 

 

prevent textile damage)

Spin: 400

 

 

 

 

Temp.: cold

 

 

 

 

 

 

Delicate

Delicated laundry easily damaged.

Cold

Wash: main wash

Refer to

 

(silk, curtains,..)

(fixed, in order to

Rinse: 2

rating lavel

 

 

prevent textile damage)

Spin: 400

 

 

 

 

Temp.: cold

 

 

 

 

 

 

Blanket

Blanket, curtains,..

Cold

Wash: main wash

Refer to

 

 

(fixed, in order to

Rinse: 3

rating lavel

 

 

prevent textile damage)

Spin: 800

 

 

 

 

Temp.: cold

 

 

 

 

 

 

Rapid

Lightly soiled clothes and frequently

30 °C

Wash: main wash

Less than 3 kg

 

washing clothes and small amount of

(cold,40°C)

Rinse: 3

 

 

clothes.

 

Spin: 800

 

 

 

 

Temp.: cold

 

 

 

 

(Dry :cupboard)

 

 

 

 

 

 

Memory

Use to memory program you want.

 

 

 

 

 

 

 

 

Drum

Use to clean (and dry) the Tub

Cold

Wash: soak

without load.

Cleaning

and Drum.

 

Rinse: 2

 

 

 

 

Spin: 400

 

 

 

 

Temp.: cold

 

 

 

 

(Dry :cupboard)

 

 

 

 

 

 

11

WASHING PROCEDURE AND SELECTION

1. NORMAL PROGRAM

Put the laundry into the Drum and put the detergent and softerner into the detergent case.

Then close the Door.

Put the detergent into the main wash room(I I marking) and prewash room(I marking)

1in the detergent case.

Softener should be below 'MAX' level.

Put the detergent into the pre wash room(I marking) only if you want to add prewash.

When you want to use bleach, put it into the main wash room (I I marking) with detergent.

2

Press the Power button.

• The LED shows only '- --' signal.

 

 

 

 

 

Select the 'NORMAL' program using the program selection dial.

 

• If you press 'Start/Pause' button aftrer pressing Power button without selecting

 

program, the 'NORMAL' program is selected as default program.

3

• Main wash' and '3' times rinse and '800' rpm spin speed and°C''40water temperature

are selected automatically.

 

 

• If you want to change the 'Washing course' and 'Rinse time(s)' and 'Spin speed' and

 

'water temperature', select program what you want to change by pressing each

 

button.

Press the 'Start/Pause' button.

4• The washer will be operated with locking Door and supplying water after sensing the amount of laundry automatically.

Note

If you want to change the setting program during operation, press the 'Start/Pause' button to hold the operation and change the program you want to change by pressing each corresponding button.

Water temperature '95°C' is not selected in order to prevent clothes from damaging.

If you want to add the clothes during operation, press 'Start/Pause' button and 'Door unlock' button, then open the Door and put the clothes into the Drum and then close Door and press 'Start/Pause' button again.

12

2. WHITE PROGRAM

Put the laundry into the Drum and put the detergent and softerner into the detergent case.

Then close the Door.

Put the detergent into the main wash room(I I marking) and prewash room(I marking)

1in the detergent case.

Softener should be below 'MAX' level.

Put the detergent into the pre wash room(I marking) only if you want to add prewash.

When you want to use bleach, put it into the main wash room (I I marking) with detergent.

2

Press the Power button.

• The LED shows only '- --' signal.

Select the 'WHITE' program using the program selection dial.

If you press 'Start/Pause' button aftrer pressing Power button without selecting program, the 'NORMAL' program is selected as default program.

3• 'Main wash' and '3' times rinse and '800' rpm spin speed°C'and '95water temperature are selected automatically.

If you want to change the 'Washing course' and 'Rinse time(s)' and 'Spin speed' , select program what you want to change by pressing each button.

Press the 'Start/Pause' button.

4• The washer will be operated with locking Door and supplying water after sensing the amount of laundry automatically.

Note

If you want to change the setting program during operation, press the 'Start/Pause' button to hold the operation and change the program you want to change by pressing each corresponding button.

Water temperature is set only to '95°C'.

If you want to add the clothes during operation, press 'Start/Pause' button and 'Door unlock' button, then open the Door and put the clothes into the Drum and then close Door and press 'Start/Pause' button again.

If much SUDS is happened during operation, the washer will clean SUDS automatically.

13

3. ECO-WHITE PROGRAM

Put the laundry into the Drum and put the detergent and softerner into the detergent case.

Then close the Door.

Put the detergent into the main wash room(I I marking) and prewash room(I marking)

1in the detergent case.

Softener should be below 'MAX' level.

Put the detergent into the pre wash room(I marking) only if you want to add prewash.

When you want to use bleach, put it into the main wash room (I I marking) with detergent.

2

Press the Power button.

• The LED shows only '- --' signal.

 

 

 

 

 

Select the 'ECO-WHITE' program using the program selection dial.

 

• If you press 'Start/Pause' button aftrer pressing Power button without selecting

 

program, the 'NORMAL' program is selected as default program.

3

• 'Main wash' and '3' times rinse and '800' rpm spin speed°C'and '60water

temperature are selected automatically.

 

 

• If you want to change the 'Washing course' and 'Rinse time(s)' and 'Spin speed' and

 

'water temperature', select program what you want to change by pressing each

 

button.

Press the 'Start/Pause' button.

4• The washer will be operated with locking Door and supplying water after sensing the amount of laundry automatically.

Note

If you want to change the setting program during operation, press the 'Start/Pause' button to hold the operation and change the program you want to change by pressing each corresponding button.

Water temperature '40°C' and '60°C' are only selected.

If you want to add the clothes during operation, press 'Start/Pause' button and 'Door unlock' button, then open the Door and put the clothes into the Drum and then close Door and press 'Start/Pause' button again.

14

4. SYNTHETIC PROGRAM

Put the laundry into the Drum and put the detergent and softerner into the detergent case.

Then close the Door.

Put the detergent into the main wash room(I I marking) and prewash room(I marking)

1in the detergent case.

Softener should be below 'MAX' level.

Put the detergent into the pre wash room(I marking) only if you want to add prewash.

When you want to use bleach, put it into the main wash room (I I marking) with detergent.

2

Press the Power button.

• The LED shows only '- --' signal.

Select the 'SYNTHETIC' program using the program selection dial.

If you press 'Start/Pause' button aftrer pressing Power button without selecting program, the 'NORMAL' program is selected as default program.

3• 'Main wash' and '3' times rinse and '800' rpm spin speed°C'and '40water temperature are selected automatically.

If you want to change the 'Washing course' and 'Rinse time(s)' and 'Spin speed' and 'water temperature', select program what you want to change by pressing each

button.

4

Press the 'Start/Pause' button.

• The washer will be operated with locking Door and supplying water.

Note

If you want to change the setting program during operation, press the 'Start/Pause' button to hold the operation and change the program you want to change by pressing each corresponding button.

Water temperature '95°C' and Spin speed '1200' are not selected.

If you want to add the clothes during operation, press 'Start/Pause' button and 'Door unlock' button, then open the Door and put the clothes into the Drum and then close Door and press 'Start/Pause' button again.

15

5. HEAVY STRAIN PROGRAM

Put the laundry into the Drum and put the detergent and softerner into the detergent case.

Then close the Door.

Put the detergent into the main wash room(I I marking) and prewash room(I marking)

1in the detergent case.

Softener should be below 'MAX' level.

Put the detergent into the pre wash room(I marking) only if you want to add prewash.

When you want to use bleach, put it into the main wash room (I I marking) with detergent.

2

Press the Power button.

• The LED shows only '- --' signal.

 

 

 

 

 

Select the 'HEAVY STRAIN' program using the program selection dial.

 

• If you press 'Start/Pause' button aftrer pressing Power button without selecting

 

program, the 'NORMAL' program is selected as default program.

3

• 'Pre wash' and '3' times rinse and '800' rpm spin speed°C'and '40water temperature

are selected automatically.

 

 

• If you want to change the 'Washing course' and 'Rinse time(s)' and 'Spin speed' and

 

'water temperature', select program what you want to change by pressing each

 

button.

 

 

 

4

Press the 'Start/Pause' button.

• The washer will be operated with locking Door and supplying water.

 

Note

If you want to change the setting program during operation, press the 'Start/Pause' button to hold the operation and change the program you want to change by pressing each corresponding button.

Water temperature '95°C' is not selected in order to prevent clothes from damaging.

If you want to add the clothes during operation, press 'Start/Pause' button and 'Door unlock' button, then open the Door and put the clothes into the Drum and then close Door and press 'Start/Pause' button again.

16

6. WOOL PROGRAM

Put the laundry into the Drum and put the detergent and softerner into the detergent case.

Then close the Door.

1• Put the detergent into the main wash room(I I marking) in the detergent case.

Softener should be below 'MAX' level.

When you want to use bleach, put it into the main wash room (I I marking) with detergent.

2

Press the Power button.

• The LED shows only '- --' signal.

Select the 'WOOL' program using the program selection dial.

If you press 'Start/Pause' button aftrer pressing Power button without selecting program, the 'NORMAL' program is selected as default program.

3• 'Main wash' and '2' times rinse and '400' rpm spin speed and 'Cold' water temperature are selected automatically.

If you want to change the 'Washing course' and 'Rinse time(s)' and 'Spin speed', select program what you want to change by pressing each button.

4

Press the 'Start/Pause' button.

• The washer will be operated with locking Door and supplying water.

Note

If you want to change the setting program during operation, press the 'Start/Pause' button to hold the operation and change the program you want to change by pressing each corresponding button.

Water temperature 'Cold' is only selected in order to prevent woolens from damaging.

Spin speed '400' and '600' are only selectable.

DRY function is not selected(option function).

DELAY START is not selected.

SOAK and Pre Wash in wash program are not selected.

If you want to add the clothes during operation, press 'Start/Pause' button and 'Door unlock' button, then open the Door and put the clothes into the Drum and then close Door and press 'Start/Pause' button again.

17

7. DELICATE PROGRAM

Put the laundry into the Drum and put the detergent and softerner into the detergent case.

Then close the Door.

1• Put the detergent into the main wash room(I I marking) in the detergent case.

Softener should be below 'MAX' level.

When you want to use bleach, put it into the main wash room (I I marking) with detergent.

2

Press the Power button.

• The LED shows only '- --' signal.

Select the 'DELICATE' program using the program selection dial.

If you press 'Start/Pause' button aftrer pressing Power button without selecting program, the 'NORMAL' program is selected as default program.

3• 'Main wash' and '2' times rinse and '400' rpm spin speed and 'Cold' water temperature are selected automatically.

If you want to change the 'Washing course' and 'Rinse time(s)' and 'Spin speed', select program what you want to change by pressing each button.

4

Press the 'Start/Pause' button.

• The washer will be operated with locking Door and supplying water.

Note

If you want to change the setting program during operation, press the 'Start/Pause' button to hold the operation and change the program you want to change by pressing each corresponding button.

Water temperature 'Cold' is only selected in order to prevent delicate clothes from damaging.

Spin speed '400' and '600' are only selectable.

DRY function is not selected(option function).

DELAY START is not selected.

SOAK and Pre Wash in wash program are not selected.

If you want to add the clothes during operation, press 'Start/Pause' button and 'Door unlock' button, then open the Door and put the clothes into the Drum and then close Door and press 'Start/Pause' button again.

18

8. BLANKET PROGRAM

Put the laundry into the Drum and put the detergent and softerner into the detergent case.

Then close the Door.

1• Put the detergent into the main wash room(I I marking) in the detergent case.

Softener should be below 'MAX' level.

When you want to use bleach, put it into the main wash room (I I marking) with detergent.

2

Press the Power button.

• The LED shows only '- --' signal.

Select the 'BLANKET' program using the program selection dial.

If you press 'Start/Pause' button aftrer pressing Power button without selecting program, the 'NORMAL' program is selected as default program.

3• 'Main wash' and '3' times rinse and '800' rpm spin speed and 'Cold' water temperature are selected automatically.

If you want to change the 'Washing course' and 'Rinse time(s)' and 'Spin speed', select program what you want to change by pressing each button.

4

Press the 'Start/Pause' button.

• The washer will be operated with locking Door and supplying water.

Note

If you want to change the setting program during operation, press the 'Start/Pause' button to hold the operation and change the program you want to change by pressing each corresponding button.

Water temperature 'Cold' is only selected in order to prevent delicate clothes from damaging.

Spin speed '400' and '600' and '800' are only selectable.

DRY function is not selected(option function).

DELAY START is not selected.

SOAK and Pre Wash in wash program are not selected.

If you want to add the clothes during operation, press 'Start/Pause' button and 'Door unlock' button, then open the Door and put the clothes into the Drum and then close Door and press 'Start/Pause' button again.

19

9. RAPID PROGRAM

Put the laundry into the Drum and put the detergent and softerner into the detergent case.

Then close the Door.

1• Put the detergent into the main wash room(I I marking) in the detergent case.

Softener should be below 'MAX' level.

When you want to use bleach, put it into the main wash room (I I marking) with detergent.

2

Press the Power button.

• The LED shows only '- --' signal.

 

 

 

 

 

Select the 'RAPID' program using the program selection dial.

 

• If you press 'Start/Pause' button aftrer pressing Power button without selecting

 

program, the 'NORMAL' program is selected as default program.

3

• 'Main wash' and '2' times rinse and '800' rpm spin speed°C'and '30water

temperature (and 'Cupboard' dry condition) are selected automatically.

 

 

• If you want to change the 'Washing course' and 'Rinse time(s)' and 'Spin speed' and

 

'water temperature', select program what you want to change by pressing each

 

button.

 

 

 

4

Press the 'Start/Pause' button.

• The washer will be operated with locking Door and supplying water.

 

Note

The appropriate amount of laundry is below 3 kg.

If you want to change the setting program during operation, press the 'Start/Pause' button to hold the operation and change the program you want to change by pressing each corresponding button.

Water temperature 'Cold' and '30°C' and '40°C' are selectable.

Spin speed '1200' is not selected.

All wash program are not selected except main wash..

If you want to add the clothes during operation, press 'Start/Pause' button and 'Door unlock' button, then open the Door and put the clothes into the Drum and then close Door and press 'Start/Pause' button again.

20

10. MEMORY PROGRAM

Put the laundry into the Drum and put the detergent and softerner into the detergent case.

Then close the Door.

Put the detergent into the main wash room(I I marking) and prewash room(I marking)

1in the detergent case.

Softener should be below 'MAX' level.

Put the detergent into the pre wash room(I marking) only if you want to add prewash.

When you want to use bleach, put it into the main wash room (I I marking) with detergent.

2Press the Power button.

The LED shows only '- --' signal.

Select the 'MEMORY' program using the program selection dial.

If you press 'Start/Pause' button aftrer pressing Power button without selecting program, the 'NORMAL' program is selected as default program.

3• If you want to memorize the 'Washing program' and 'Washing course' and 'Rinse time(s)' and 'Spin speed' and 'water temperature' (and 'Dry condition'), select somethings what you want to change by pressing each button and using the program selection dial.

4

Press the 'Start/Pause' button.

• The washer will be operated with locking Door and supplying water.

 

Note

If you start memorized program, this data will be saved automatically.

If you want to change the setting program during operation, press the 'Start/Pause' button to hold the operation and change the program you want to change by pressing each corresponding button.

If you want to add the clothes during operation, press 'Start/Pause' button and 'Door unlock' button, then open the Door and put the clothes into the Drum and then close Door and press 'Start/Pause' button again.

21

11. DRUM CLEANING PROGRAM

Put the laundry into the Drum and put the detergent and softerner into the detergent case.

1Then close the Door.

If you want to clean Drum slightly, use this program without Bleach.

If you want to clean Drum thoroughly, please use the exclusive detergent.

2

Press the Power button.

• The LED shows only '- --' signal.

Select the 'DRUM CLEANING' program using the program selection dial.

• If you press 'Start/Pause' button aftrer pressing Power button without selecting

3program, the 'NORMAL' program is selected as default program.

'Soak' and '2' times rinse and '400' rpm spin speed and 'Cold' water temperature (and 'Cupboard' dry condition) are selected automatically.

4

Press the 'Start/Pause' button.

• The washer will be operated with locking Door and supplying water.

Note

All programs are not selectable except rinse time(s).

DELAY START is not selected.

Use this program WITHOUT load.

The appropriate cleaning time is one time per a month.

22

GUIDE FOR OTHER USEFUL PROGRAMS

* DELAY START(RESERVED WASHING)

Put the laundry into the Drum and put the detergent and softerner into the detergent case.

Then close the Door.

Put the detergent into the main wash room(I I marking) and prewash room(I marking)

1in the detergent case.

Softener should be below 'MAX' level.

Put the detergent into the pre wash room(I marking) only if you want to add prewash.

When you want to use bleach, put it into the main wash room (I I marking) with detergent.

2Press the Power button.

The LED shows only '- --' signal.

Select the program using the program selection dial.

• If you press 'Start/Pause' button aftrer pressing Power button without selecting

3program, the 'NORMAL' program is selected as default program.

Select the 'Washing course' and 'Rinse time(s)' and 'Spin speed' and 'water temperature' by pressing each corresponding button.

 

Press the 'DELAY START' button.

4

• The 'Time Delay' LED is to be lighting.

• Select the time delay time you want from 1 hour to 12 hours by pressing button.

 

 

• The displayed time shows program finishing time.

 

 

 

Press the 'Start/Pause' button.

5

• If you make this program successfully, only 'Time Delay' andLock' ' LED are lighting.

Note

If you want to check the selected program, press the 'Start/Pause' button again.

Preparing washing before starting 'Time Delay';

-Turn on the water tap.

-Load laundry and close Door.

-Place the detergent and fabric softner in the detergent case.

The actual time of finishing is a little different with your selecting time because of water supply condition and selected water temperature,....

'WOOL' and 'DELICATE' and 'DRUM CLEANING' program are not select 'Time Delay'.

Adding clothes during 'Time Delay' operation is not allowed.

23

* ONLY WASH

Put the laundry into the Drum and put the detergent and softerner into the detergent

1case.

Then close the Door.

2Press the Power button.

The LED shows only '- --' signal.

3Select the 'WASH COURSE' you want by pressing 'WASH' button.

The 'NORMAL' program is selected automatically.

4Press the 'Start/Pause' button.

The washer will be operated with locking Door and supplying water.

*ONLY RINSE

Put the laundry into the Drum and put the detergent and softerner into the detergent

1case.

Then close the Door.

2Press the Power button.

The LED shows only '- --' signal.

3Select the 'RINSE' time(S) you want by pressing 'RINSE' button.

The 'NORMAL' program is selected automatically.

4Press the 'Start/Pause' button.

The washer will be operated with locking Door and supplying water.

*ONLY SPIN

1Put the laundry into the Drum and close the Door.

2

Press the Power button.

• The LED shows only '- --' signal.

Select the 'SPIN CONDITION' you want by pressing 'SPIN' button.

3• The 'NORMAL' program is selected automatically.

• The water temperature is selected to 'Cold' automatically.

4

Press the 'Start/Pause' button.

• The washer will be operated with locking Door.

24

* DRY(DWD-E1211R'S)

1

Put the laundry into the Drum and close the Door.

2

Press the Power button.

• The LED shows only '- --' signal.

Select the 'DRY CONDITION' you want by pressing 'DRY' button.

3As this button is pressed, the dry condition is selected by 'Cupboard'→ 'Very' → 'Time(30, 1:00, 1:30)'→ OFF → 'Low Temp'→ 'Iron'→ 'Cupboard'

4Press the 'Start/Pause' button.

• The washer will be operated with locking Door.

Note

Do not use the detergent and softener.

Cold water tap should be opened.

After finishing this program, is showed on PCB board alternately and the smoothing creases program is conducted during 30 minute and then power is OFF.

'WOOL' and 'DELICATE' and 'BLANKET' program are not select 'DRY'.

Be careful the high temperature of laundry when put out clothes.

A little shrikage and deformation will be possibly happened after drying, so check clothes whether dry or not previously

If the dry performance is poor, change the selecting temperature.

If youn want to dry with wash, after selecting program, press the 'DRY' button then press 'Start/Pause' button.

25

* RINSE+SPIN(DWD-E1211W'S)

Put the laundry into the Drum and put softerner into the detergent case.

1Then close the Door.

• Softener should be below 'MAX' level.

2

Press the Power button.

• The LED shows only '- --' signal.

Select the program you want using the program selection dial.

3• If you press 'RINSE+SPIN' button without selecting program, the 'NORMAL' program is selected as default program.

 

Press the 'RINSE+SPIN' button.

 

• '1' time rinse and '800' rpm spin speed and 'Cold' water temperature are selected

4

automatically.

• '400' rpm spin speed is selected in 'WOOL' and 'DELICATE' program.

 

 

• If you want to change the Rinse time(s) and Spin condition, press each

 

corresponding button.

 

 

 

5

Press the 'Start/Pause' button.

• The washer will be operated with locking Door.

 

Note

The water temperature selecting is possible during this process.

You can add the washing course during this process by pressing 'WASH' button.

26

MAINTENANCE

Proper care of your washer can extend its life. This section explains how to care for your washer properly and safely.

Cleaning your washer

Exterior

Interior

 

 

Wipe up detergent, bleach, and other spills with

Clean interior with 250ml of chlorine bleach

a soft, damp cloth or sponge as they occur.

mixed with 500ml of detergent.

Occasionally wipe the outside of the washer to

Run washer through a complete cycle.

keep its looking like new one.

Repeat this process if necessary.

 

 

Do not put sharp or metal object in your washer, or they can damage the finish. Check all pockets for pins, clips, money, bolts, nuts, etc.

Do not lay these objects in your washer after emptying pockets.

Winter storage or moving care

Install and store your washer where it will not freeze. Because some water may stay in the hoses, freezing can damage your washer.

If you store or move your washer during freezing weather, winterize it.

To winterize washer

To use washer again

 

 

• Turn off water faucet.

• Flush water pipes and hoses.

• Disconnect and drain water inlet hoses.

• Reconnect water inlet hoses.

• Run washer on a drain and spin setting (see

• Turn on water faucet.

page 10) for 1 minute.

• Reconnect power supply cord.

• Unplug the power supply cord.

 

 

 

Non-use or vacation care

Operate your washer only when you are at home.

If you are on vacation or don’t use your washer for an extended period of time, you should:

Unplug the power supply cord or turn off eletrical power to the washer.

Turn off the water supplier to the washer.

This helps avoid accidental flooding (due to a water pressure surge) while you are away.

27

HOW TO CLEAN THE FILTER

Cleaning the water inlet filter

• Clean the filter when water leaks from the water inlet.

1Pull the power plug out before cleaning it.

2Turn off the water

3Pull the inlet filter

4Remove the dirt

supply to the

out.

from the inlet filter

washer and

 

with a brush.

separate the inlet

 

 

hose.

 

 

Cleaning the drain filter

This drain filter is used to screen the foreign stuffs such as threads, coins, pins, buttons etc..

If the drain filter is not cleaned at proper time(every 10 times of use), drain problem could be caused.

CAUTION : Be careful when draining if the water is hot.

1.Open the lower cover(1) by using a coin. Remove the cap hose(2) to pull out the hose.

1

2.Unplug the cap hose(2), allowing the water to flow out. At this time use a vessel to prevent water flowing on to the floor. When water does not flow any more, turn the pump filter(3) open to the left.

2

3

3.Remove any foreign material from the pump filter(3). After cleaning, turn the pump filter clockwise and insert the cap hose(2) to the original place. Close the lower cover.

3

2

Cleaning the detergent case

*After a while detergent and fabric softeners leave a deposit in the case;

-It should be cleaned from time to time with a jet of running water.

-If necessary it can be removed completely from the machine by pressing the catch downwards and by pulling it out.

-To facilitate cleaning, the upper part of the fabric softener compartment can be removed.

*Detergent can also accumulate inside the recess which should be cleaned occasionally with a brush.

*Once you have finished cleaning, replace the case and run a rinse cycle without laundry.

28

REMOVING STAINS

Stained, heavily-soiled, or greasy items may need to be prewashed or soaked for best results. Soaking helps remove protein-type stains like blood, milk or grass. Prewashing helps loosen soil before washing.

Stain removal rules

Use warm water for soaking or prewashing stained laundry. Hot water can set stains.

Most stains are easier to remove when they are fresh.

Before treating any stain, find out what kind of stain it is, how old the stain is, what kind of fabric it is, and whether the fabric is colorfast. (Check the care label)

Washing and drying can set some stains.

Start with cold or warm water. Hot water can set some stains.

When bleach is recommended, use a bleach that is safe for the fabric.

Put the stained area face down on a paper towel or white cloth. Apply the stain remover to the back of the stain. This forces the stain off fabric instead of through it.

Stain removal guide

STAIN

TO REMOVE

 

 

Blood

Rinse immediately in COLD water.

 

If stain remains, soak in cold water with an enzyme prewash.

Chewing gum

Use ice in plastic bag to harden the gum.

 

Scrape off what you can and the sponge with white spirits.

Cocoa, Chocolate

Sponge with COLD water and soak in an enzyme prewash.

 

If stains persist, rub in a little detergent and rinse in cold water.

Coffee

Blot up quickly and rinse out in COLD water.

 

Rub in a little detergent and wash in the maximum temperature allowed for the

 

fabric type.

Cream/Milk

Rinse in COLD water and wash normally.

Ice cream

If stain is still apparent, sponge with white spirits.

Deodorant

Rub affected area with white vinegar and then rinse out in COLD water.

 

Sponge with white spirits.

 

Treat stiffened areas with enzyme prewash.

Egg

Soak in a COLD enzyme prewash, rinse and wash normally.

Fabric/Softener

Rub affected area with bar soap and wash normally.

Fruit stains

Treat as soon as possible by sponging with COLD water.

 

Rub a little detergent on the stain and wash normally.

Grass

Sponge with white spirits.

 

Rub in an enzyme prewash and wash as normally.

Grease and oil

Lay the affected area face down on an absorbent cloth and work from the back.

 

Sponge with white spirits or dry cleaning fluid. Wash normally.

Iron or rust

Apply lemon juice and salt and place in the sun. Wash normally.

Lipstick

Sponge with white methylated spirits and wash normally.

Mildew

Wash in WARM water and detergent.

 

Moisten area with lemon juice, dry in the sun and wash normally.

 

If stain persists and the fabric allows, use a bleach.

Mud

Brush off any dry mud. Rinse in cold water.

 

If stain persists rub in a little detergent and wash normally.

Paint-oil based

Scrape off any fresh paint and sponge with a non flammable dry cleaning fluid

 

and wash normally.

Paint-water based

Treat while still wet, rinse in WARM water and wash normally.

Scorch marks

Dampen a cloth with hydrogen peroxide, lay it over the affected area and press

 

with a fairly hot iron.

 

 

29

TROUBLE SHOOTING

Most problems are easily solved if you understand the cause. Check the following list for problem before calling for service.

If error mode such as IE, OE, UE were displayed on the control part, in this case, how to solve these problem is first open and close the door, and then press START/PAUSE button.

 

PROBLEM

 

CHECK POINT

 

 

 

 

 

 

 

 

• The washer will not

 

• Is there a power failure?

 

operate at all.

 

• Is the power cord correctly connected to an electric outlet?

 

 

 

 

 

• Did you turn on the power?

 

 

 

 

 

• Did you press Start/Hold button?

 

 

 

 

 

• Is there correct amount of laundry in the washer.

 

 

 

 

 

• Water is not supplied

 

• Did you connect the inlet hose and open the water tap?

 

 

 

 

 

• Is the inlet hose or the water tap frozen?

 

Error display

 

 

 

 

 

 

 

 

 

• Is the water supply shot off?

 

 

 

 

 

 

 

 

 

• Is there any foreign matter blocking up the inlet hose filter?

 

 

 

 

 

• The washer will not drain

 

• Is the drain hose frozen or blocked up by dirt?

 

 

 

• Is the drain hose kinked or deformed?

 

Error display

 

 

 

 

 

 

 

 

 

• Is the end of the drain hose immersed in water?

 

 

 

 

 

 

 

 

 

• Is there excessive dirt inside the drain filter?

 

 

 

 

 

• The washer will not spin

 

• Is the clothes in the drum collected on one side?

 

 

 

 

 

• Is the washer installed on an uneven floor or is the vibration

 

Error display

 

 

 

 

 

 

 

 

 

serious?

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Is the door open? (The lamp “

will” light up in this case.)

 

 

 

 

 

• Vibrating and too noisy

 

• Is the washer installed on an uneven floor?

 

 

 

 

 

• Have all the transit bolts removed?

 

 

 

 

 

 

 

Note

• If and error mode are showed on PCB board, please contact service center.

These cases are not malfunctions;

The sound “wing” heard during water supply is the operating sound made by the water inlet valve.

The sound “sha” heard in stopping the tub is the sound that comes from the autobalbancer of the tub.

30

SPECIFICATION

MODEL

DWD-E1211R’S

 

DWD-E1211W’S

 

 

 

 

Dimension (mm)

630 x 750 x 930 (WxDxH)

Unit Weight (kg)

80(Net) / 88(Gross)

 

 

 

Maximum Mass of Dry Cloth

Wash: 11Kg (Dry: 6.5Kg)

 

 

 

 

Standard Water Consumption

 

110 l

 

 

 

Spin Speed (RPM)

No Spin/400/600/800/1000/1200

 

 

 

Operating Water Pressure

0.03MPa ~ 0.8MPa (0.3kgf/cm2 ~ 8kgf/cm2)

 

 

 

 

WIRING DIAGRAM

DWD-E1211R’S

DWD-E1211W’S

31

ABOUT THIS MANUAL

VISION CREATIVE, INC.

6 4

 

 

 

TEL

 

 

 

 

 

MODEL

DWD-E1211R’S, E1211W’S

 

 

 

 

 

 

BUYER

_BASIC

 

 

 

 

 

 

 

 

 

1

6

 

 

 

 

 

 

 

 

2

7

 

 

 

 

 

 

 

 

3

8

 

 

 

 

 

 

 

 

4

9

 

 

 

 

 

 

 

 

5

10

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MEMO 2005.3.29_31page 2005.3.31-9,10,11 2005.4.20-31

2005.4.28-31p-WIRING DIAGRAM 2 2005.4.29- ,2p,31pWIRING DIAGRAM

 

 

VISION

 

TEL: 730-0660 FAX: 730-3788