DADD DDU8F-5075, DDU8F-5060MD4, DDU8F-5060MD1, DDU8F-5060M, DDU8F-5060B1 Datasheet

Military SMD DDU8F-xxMD1 DDU8F-xxMD4

DDU8F

5-TAP, TTL-INTERFACED FIXED DELAY LINE (SERIES DDU8F)

data 3 ® delay

devices, inc.

FEATURES

∙Five equally spaced outputs

∙Fits standard 8-pin DIP socket

∙Low profile

∙Auto-insertable

∙Input & outputs fully TTL interfaced & buffered

∙10 T2L fan-out capability

PACKAGES

IN					VCC	IN	1	14	VDD
		1	8			N/C	2	13	N/C
T2		2	7		T1	N/C	3	12	T1
						T2	4	11	N/C
T4			6		T3
		3				N/C	5	10	T3
GND		4	5		T5	T4	6	9	N/C
						GND	7	8	T5

DDU8F-xx DIP

DDU8F-xxA1 Gull-Wing

DDU8F-xxB1 J-Lead

DDU8F-xxM Military DIP

FUNCTIONAL DESCRIPTION	PIN DESCRIPTIONS
The DDU8F-series device is a 5-tap digitally buffered delay line. The	IN	Signal Input
signal input (IN) is reproduced at the outputs (T1-T5), shifted in time by an	T1-T5	Tap Outputs
amount determined by the device dash number (See Table). For dash	VCC	+5 Volts
numbers less than 5025, the total delay of the line is measured from T1 to	GND	Ground
T5. The nominal tap-to-tap delay increment is given by one-fourth of the

total delay, and the inherent delay from IN to T1 is nominally 3.5ns. For dash numbers greater than or equal to 5025, the total delay of the line is measured from IN to T5. The nominal tap-to-tap delay increment is given by one-fifth of this number.

SERIES SPECIFICATIONS

∙Minimum input pulse width: 40% of total delay

∙Output rise time: 2ns typical

∙Supply voltage: 5VDC ± 5%

∙Supply current: ICCL = 32ma typical

ICCH = 7ma typical

∙Operating temperature: 0° to 70° C

∙Temp. coefficient of total delay: 100 PPM/°C

3.5ns 25% 25% 25% 25%

VCC IN

T1

T2

T3

T4

T5 GND

Functional diagram for dash numbers < 5025

20% 20% 20% 20% 20%

VCC IN

T1

T2

T3

T4

T5 GND

Functional diagram for dash numbers >= 5025

©1997 Data Delay Devices

DASH NUMBER SPECIFICATIONS

Part	Total		Delay Per
Number	Delay (ns)		Tap (ns)
DDU8F-5004	4 ± 1.0 *		1.0 ± 0.5
DDU8F-5006	6 ± 1.0 *		1.5 ± 0.5
DDU8F-5008	8 ± 2.0 *		2.0 ± 1.0
DDU8F-5010	10 ± 2.0 *		2.5 ± 1.0
DDU8F-5012	12 ± 2.0 *		3.0 ± 1.0
DDU8F-5016	16 ± 2.0 *		4.0 ± 1.5
DDU8F-5020	20 ± 3.0 *		5.0 ± 2.0
DDU8F-5025	25	± 3.0	5.0 ± 2.0
DDU8F-5030	30	± 3.0	6.0 ± 2.0
DDU8F-5035	35	± 3.0	7.0 ± 2.0
DDU8F-5040	40	± 3.0	8.0 ± 2.0
DDU8F-5045	45	± 3.0	9.0 ± 3.0
DDU8F-5050	50	± 3.0	10.0 ± 3.0
DDU8F-5060	60	± 3.0	12.0 ± 3.0
DDU8F-5075	75	± 4.0	15.0 ± 3.0
DDU8F-5100	100 ± 5.0		20.0 ± 3.0
DDU8F-5125	125 ± 6.5		25.0 ± 3.0
DDU8F-5150	150 ± 7.5		30.0 ± 3.0
DDU8F-5175	175 ± 8.0		35.0 ± 4.0
DDU8F-5200	200	± 10.0	40.0 ± 4.0
DDU8F-5250	250	± 12.5	50.0 ± 5.0

*Total delay is referenced to first tap output Input to first tap = 3.5ns ± 1ns

NOTE: Any dash number between 5004 and 5250 not shown is also available.

Doc #97012

DATA DELAY DEVICES, INC.

1

1/28/97

3 Mt. Prospect Ave. Clifton, NJ 07013

DDU8F

APPLICATION NOTES

HIGH FREQUENCY RESPONSE

The DDU8F tolerances are guaranteed for input pulse widths and periods greater than those specified in the test conditions. Although the device will function properly for pulse widths as small as 40% of the total delay and periods as small as 80% of the total delay (for a symmetric input), the delays may deviate from their values at low frequency. However, for a given input condition, the deviation will be repeatable from pulse to pulse. Contact technical support at Data

Delay Devices if your application requires device testing at a specific input condition.

POWER SUPPLY BYPASSING

The DDU8F relies on a stable power supply to produce repeatable delays within the stated tolerances. A 0.1uf capacitor from VCC to GND, located as close as possible to the VCC pin, is recommended. A wide VCC trace and a clean ground plane should be used.

DEVICE SPECIFICATIONS

TABLE 1: ABSOLUTE MAXIMUM RATINGS

PARAMETER	SYMBOL	MIN	MAX	UNITS	NOTES
DC Supply Voltage	VCC	-0.3	7.0	V
Input Pin Voltage	VIN	-0.3	VDD+0.3	V
Storage Temperature	TSTRG	-55	150	C
Lead Temperature	TLEAD		300	C	10 sec

TABLE 2: DC ELECTRICAL CHARACTERISTICS

(0C to 70C, 4.75V to 5.25V)

PARAMETER	SYMBOL	MIN	TYP	MAX	UNITS	NOTES
High Level Output Voltage	VOH	2.5	3.4		V	VCC = MIN, IOH = MAX
						VIH = MIN, VIL = MAX
Low Level Output Voltage	VOL		0.35	0.5	V	VCC = MIN, IOL = MAX
						VIH = MIN, VIL = MAX
High Level Output Current	IOH			-1.0	mA
Low Level Output Current	IOL			20.0	mA
High Level Input Voltage	VIH	2.0			V
Low Level Input Voltage	VIL			0.8	V
Input Clamp Voltage	VIK			-1.2	V	VCC = MIN, II = IIK
Input Current at Maximum	IIHH			0.1	mA	VCC = MAX, VI = 7.0V
Input Voltage
High Level Input Current	IIH			20	μA	VCC = MAX, VI = 2.7V
Low Level Input Current	IIL			-0.6	mA	VCC = MAX, VI = 0.5V
Short-circuit Output Current	IOS	-60		-150	mA	VCC = MAX
Output High Fan-out				25	Unit
Output Low Fan-out				12.5	Load

Doc #97012

DATA DELAY DEVICES, INC.

2

1/28/97

Tel: [phone] Fax: [phone] http://www.datadelay.com