Crown Audio XTi 4002, XTi 1002, XTi 6002, XTi 2002 User manual

4 (1)

XTi2 Series Operation Manual

XTi 1002

XTi 2002

XTi 4002

XTi 6002

Obtaining Other Language Versions: To obtain information in another language about the use of this product, please contact your local Crown Distributor. If you need assistance locating your local distributor, please contact Crown at 574-294-8000.

This manual does not include all of the details of design, production, or variations of the equipment. Nor does it cover every possible situation which may arise during installation, operation or maintenance.

The information provided in this manual was deemed accurate as of the publication date. However, updates to this information may have occurred. To obtain the latest version of this manual, please visit the Crown website at www.crownaudio.com.

Trademark Notice: Crown, Crown Audio, and Amcron are registered trademarks of Crown International. Other trademarks are the property of their respective owners. Later versions of this manual and additional information about this product may be available at the Crown website at www.crownaudio.com.

Some models may be exported under the name Amcron®

©2011 by Harman International, 1718 W. Mishawaka Rd., Elkhart, Indiana 46517-9439 U.S.A. Telephone: 574-294-8000.

143060-2 - 4/11

XTi2 Series Power Amplifiers

Important Safety Instructions

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with a dry cloth.

7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11.Only use attachments/accessories specified by the manufacturer.

12.Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13.Unplug this apparatus during lightning storms or when unused for long periods of time.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15.Use the mains plug to disconnect the apparatus from the mains.

16.WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

17.DO NOT EXPOSE THIS EQUIPMENT TO DRIPPING OR SPLASHING AND ENSURE THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, ARE PLACED ON THE EQUIPMENT.

18.THE MAINS PLUG OF THE POWER SUPPLY CORD SHALL REMAIN READILY OPERABLE.

TO PREVENT ELECTRIC SHOCK DO NOT REMOVE TOP OR BOTTOM COVERS. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

TO COMPLETELY DISCONNECT THIS EQUIPMENT FROM THE

AC MAINS, DISCONNECT THE POWER SUPPLY CORD PLUG FROM THE AC RECEPTACLE. THE MAINS PLUG OF THE POWER SUPPLY CORD SHALL REMAIN READILY OPERABLE.

WATCH FOR THESE SYMBOLS:

The lightning bolt triangle is used to alert the user to the risk of electric shock.

The exclamation point triangle is used to alert the user to important operating or maintenance instructions.

IMPORTANT

XTi2 Series amplifiers require Class 2 output wiring.

MAGNETIC FIELD

CAUTION! Do not locate sensitive high-gain equipment such as preamplifiers or tape decks directly above or below the unit. Because this amplifier has a high power density, it has a strong magnetic field which can induce hum into unshielded devices that are located nearby. The field is strongest just above and below the unit.

If an equipment rack is used, we recommend locating the amplifier(s) in the bottom of the rack and the preamplifier or other sensitive equipment at the top.

FCC COMPLIANCE NOTICE

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

t 3FPSJFOU PS SFMPDBUF UIF SFDFJWJOH BOUFOOB t *ODSFBTF UIF TFQBSBUJPO CFUXFFO UIF FRVJQNFOU BOE SFDFJWFS

t $POOFDU UIF FRVJQNFOU JOUP BO PVUMFU PO B DJSDVJU EJGGFSFOU GSPN UIBU to which the receiver is connected.

t $POTVMU UIF EFBMFS PS BO FYQFSJFODFE SBEJP 57 UFDIOJDJBO GPS IFMQ

page 2

Operation Manual

XTi2 Series Power Amplifiers

DECLARATION OF CONFORMITY

Issued By: Harman International.

FOR FIELD SERVICE

 

1718 W. Mishawaka Rd.

QUESTIONS CALL:

1 800 342 6939

Elkhart, IN 46517 U.S.A.

European Representative’s Name and Address:

David J. Budge

10 Harvest Close

Yateley

GU46 6YS

United Kingdom

Equipment Type: Power amplifiers

Family Name: XTi2 Series

Model Names: XTi1002, XTi2002, XTi4002, XTi6002

EMC Standards:

EN 55103-1:1997 Electromagnetic Compatibility – Product Family Standard for Audio, Video, Audio-Visual and Entertainment Lighting Control Apparatus for Professional Use, Part 1: Emissions

EN 55103-1:1997 Magnetic Field Emissions-Annex A @ 10 cm and 1 M

EN 61000-3-2:2005 & Amd 1: 2008 Limits for Harmonic Current Emissions (equipment input current ≤16A per phase)

EN 61000-3-3:1998 Limitation of Voltage Fluctuations and Flicker in Low-Voltage Supply Systems Rated Current ≤16A

EN 55022:2006 Limits and Methods of Measurement of Radio Disturbance Characteristics of ITE: Radiated, Class B Limits; Conducted, Class B

EN 55103-2:1997 Electromagnetic Compatibility – Product Family Standard for Audio, Video, Audio-Visual and Entertainment Lighting Control Apparatus for Professional Use, Part 2: Immunity

EN 61000-4-2:2001 Electrostatic Discharge Immunity (Environment E2-Criteria B, 4k V Contact, 8k V Air Discharge)

EN 61000-4-3:2006 Radiated, Radio-Frequency, Electromagnetic Immunity (Environment E2, Criteria A)

EN 61000-4-4:2007 Electrical Fast Transient/Burst Immunity (Criteria B)

EN 61000-4-5:2006 Surge Immunity (Criteria B)

EN 61000-4-6:2006 Immunity to Conducted Disturbances Induced by Radio-Frequency Fields (Criteria A)

EN 61000-4-11:2001 Voltage Dips, Short Interruptions and Voltage Variation

Safety Standard:

IEC 60065: 2001: 7Ed & Amd 1: 2005 Safety Requirements - Audio Video and Similar Electronic Apparatus

I certify that the product identified above conforms to the requirements of the EMC Council Directive 89/336/EEC as amended by 92/31/EEC, and the Low Voltage Directive 73/23/EES as amended by 93/68/EEC.

Signed ______________________

Scott Potosky

Title: Director of Engineering

Date of Issue: February 1, 2011

Operation Manual

page 3

XTi2 Series Power Amplifiers

Get Started

Stereo DSP Off

This is the default mode the amplifier is set to from the factory. The amplifier is configured for stereo mode with all processing disabled.

1.Connect Left/Right signal source to Channel 1 and Channel 2 using the XLR connectors.

2.Connect a speaker to each channel output using Speakon®, Banana Plugs, or bare wire.

WARNING: Before you start to set up your amplifier, make sure you read and observe the Important Safety Instructions found at the beginning of this manual.

XTi 6002 back panel shown.

See page 9 for XTi 1002, 2002 and 4002 back panel.

Factory Preset #2: BRIDGE

Putting the amplifier in BRIDGE (bridge-mono) mode delivers the power of both amp channels into a single 8 or 4 ohm load. The XTi2 Series amplifiers

come pre-loaded with a preset that makes it easy to configure the amplifier for this operation.

Before you get started ensure that you:

1. Connect signal source to Channel 1 and Channel 2 using XLR connectors (the amplifier inputs will automatically be summed together when selecting this preset).

2.Connector the speaker as shown.

a.If using the binding post outputs, connect the positive terminal of the speaker to the positive terminal of Channel 1 and the negative terminal of the speaker to the positive terminal of Channel 2.

b.If using a Speakon® connector, connect the positive terminal of the speaker to 1+ and the negative terminal to 2+. Plug the connector into the Channel 1 output only.

Follow these quick steps to configure the amplifier for BRIDGE operation:

1.Push the “Set/Enter” button and you will see the word “Preset” flashing.

2.Push the “Set/Enter” button again to enter the list of presets in the amplifier.

3.Push the “Next/Down” or “PREV/UP” button until the screen displays “Bridge”.

4.Push the “Set/Enter” button to confirm your selection.

5.The display will now read “Bridge” with the Y icon and Bridge icon highlighted.

NOTE: Custom wiring should only be performed by qualified personnel.

page 4

Operation Manual

XTi2 Series Power Amplifiers

Get Started

Factory Preset #3: XOVER

Putting the amplifier in XOVER mode enables a 1.2kHz 4th order (24dB/octave) filter that sends frequencies of 1.2kHz and below to Channel 1 output and frequencies of 1.2kHz and above to Channel 2 output. The XTi2 Series amplifiers come pre-loaded with a preset that makes it easy to configure the amplifier for this operation.

Before you get started ensure that you:

1.Connect signal source to Channel 1 ONLY using an XLR connector (the amplifier inputs will automatically be put into Y mode when selecting this preset).

2.Connector the speaker as shown.

HIGH 2+/–

LOW 1+/–

a. Connect the speaker you wish to receive the low and mid frequencies (1.2kHz and below) to Channel 1 output using Speakon®, Banana Plugs, or bare wire.

b. Connect the speaker you wish to receive the high frequencies (1.2kHz and above) to Channel 2 output using Speakon®, Banana Plugs, or bare wire.

Follow these quick steps to configure the amplifier for XOVER operation:

1.Push the “Set/Enter” button and you will see the word “Preset” flashing.

2.Push the “Set/Enter” button again to enter the list of presets in the amplifier.

3.Push the “Next/Down” or “PREV/UP” button until the screen displays “BIAMP”.

4.Push the “Set/Enter” button to confirm your selection.

5.The display will now read “BIAMP” with the Y icon and XOV icon highlighted.

Factory Preset #4: BRG SUBS

Putting the amplifier in BRG SUBS (bridged subs) mode allows you to bridge the amplifier for use with a single 8 or 4 ohm subwoofer. The inputs are automatically summed, a 90Hz 4th order (24dB/octave) LowPass filter is enabled, and the output mode is put into bridge-mono mode. The XTi2 Series amplifiers come pre-loaded with a preset that makes it easy to configure the amplifier for this operation.

Before you get started ensure that you:

1.Connect signal source to Channel 1 and Channel 2 using XLR connectors (the amplifier inputs will automatically be summed together

when selecting this preset).

2. Connector the speaker as shown.

a.If using the binding post outputs, connect the positive terminal of the

speaker to the positive terminal of Channel 1 and the negative terminal of the speaker to the positive terminal of Channel 2.

b.If using a Speakon® connector, connect the positive terminal of the speaker to 1+ and the negative terminal to 2+. Plug the connector into the Channel 1 output only. Follow these quick steps to configure the amplifier for XOVER operation:

1.Push the “Set/Enter” button and you will see the word “Preset” flashing.

2.Push the “Set/Enter” button again to enter the list of presets in the amplifier.

3.Push the “Next/Down” or “PREV/UP” button until the screen displays “XOVER”.

4.Push the “Set/Enter” button to confirm your selection.

5.The display will now read “XOVER” with the Y icon and XOV icon highlighted.

Operation Manual

page 5

XTi2 Series Power Amplifiers

Get Started

Factory Preset #5: SUBSYNTH

Putting the amplifier in SUBSYNTH mode allows you to turn on the SubHarmonic Synth feature for use with a subwoofer on both channels. The inputs are automatically summed, a 90Hz 4th order (24dB/octave) filter is enabled on both Channel 1 and Channel 2, and the SubHarmonic Synth feature is turned on at +12dB level. The XTi2 Series amplifiers come pre-loaded with a preset that makes it easy to configure the amplifier for this operation.

Before you get started ensure that you:

1.Connect signal source to Channel 1 and Channel 2 using XLR connectors (the amplifier inputs will automatically be summed together when

selecting this preset).

2. Connector the speaker as shown.

a.Connect a speaker to each channel output using Speakon©, Banana Plugs, or bare wire

Follow these quick steps to configure the amplifier for SUBSYNTH operation:

1.Push the “Set/Enter” button and you will see the word “Preset” flashing.

2.Push the “Set/Enter” button again to enter the list of presets in the amplifier.

3.Push the “Next/Down” or “PREV/UP” button until the screen displays “SUBSYNTH”.

4.Push the “Set/Enter” button to confirm your selection.

5.The display will now read “SUBSYNTH” with the Y icon and XOV icon highlighted.

Ensure Proper Cooling

When using an equipment rack, mount units directly on top of each other. Close any open spaces in rack with blank panels. DO NOT block front or rear air vents. The side walls of the rack should be a minimum of two inches (5.1 cm) away from the amplifier sides, and the back of the rack should be open.

CAUTION: Before you begin installing your amplifier, make sure it is disconnected from the power source, with the power switch in the “off” position and all level controls turned completely down (counterclockwise).

page 6

Operation Manual

XTi2 Series Power Amplifiers

Welcome

There’s no debate – when you choose Crown’s XTi2 Series, you’re choosing one of the most powerful and innovative amplifiers on the market today. That’s because the all-new XTi2 Series amps continue to set the standard for unmatched performance and value, delivering the goods night after night without breaking a sweat.

With such innovations as a universal tracking switch-mode power supply and a fully integrated suite of speaker processing tools, these amps are at the top of their class when it comes to thermal efficiency and system flexibility.

You also have greatly improved control capabilities. The addition of PeakX Plus™ Limiters gives you full command over threshold, attack and release, and we enhanced the Subharmonic Synth so you can easily manage frequency, gain and filter type, allowing for application specific tuning.

Plus, you’ll now be able to tailor fan speed for specific applications with the new Advanced Thermal controls and have software visibility of the Power Supply Temperature and AC Line Voltage with the new Advanced Monitoring controls. Combine all of that with integrated cast-aluminum rack handles for maximum durability and portability and you have the power to move you – and the world.

Next Generation Features include:

t 1FBL9 1MVT -JNJUFST QSPWJEF UIF VMUJNBUF JO TZTUFN QFSGPSNBODF BOE QSPUFDUJPO CZ BMMPXJOH full control over threshold, attack, and release

t &OIBODFE 4VCIBSNPOJD 4ZOUI TFDUJPO QSPWJEFT VTFS DPOUSPM PWFS DSPTTPWFS GSFRVFODZ NBY IBSNPOJD GSFRVFODZ and 1 PEQ filter for system-specific tuning

t /FX "EWBODFE 5IFSNBM DPOUSPMT BMMPX GPS VTFS EFmOFE GBO NPEF DPOUSPMT o OPSNBM FBSMZ and full speed – for matching fan performance to a specific application

t /FX "EWBODFE .POJUPSJOH QSPWJEFT TPGUXBSF WJTJCJMJUZ PG UIF 1PXFS 4VQQMZ 5FNQFSBUVSF BOE "$ -JOF 7PMUBHF t *ODSFBTFE OVNCFS PG QSFTFUT UP B UPUBM PG PG XIJDI BSF VTFS EFmOBCMF

t *OUFHSBUFE oDBTU BMVNJOVN IBOEMFT GPS FBTZ IBOEMJOH BOE FOIBODFE EVSBCJMJUZ

t -PDLJOH QPXFS DPSE DMJQ QSPWJEFT B TFDVSF DPOOFDUJPO CFUXFFO UIF BNQMJmFS BOE QPXFS DPSE t 6QEBUFE )J2OFU #BOE .BOBHFS BOE 4ZTUFN "SDIJUFDU DPOUSPM TPGUXBSF

How to Use This Manual

This manual provides you with the necessary information to safely and correctly setup and operate your amplifier. It does not cover every aspect of installation, setup, or operation that might occur under every condition. For additional information, please consult Crown’s Amplifier Application Guide (available at www.crownaudio.com), Crown Technical Support, your system installer or retailer.

We strongly suggest you read all instructions, warnings and cautions contained in this manual. Also, for your protection, please send in your warranty registration card today. And save your bill of sale – it’s your official proof of purchase.

Operation Manual

page 7

Crown Audio XTi 4002, XTi 1002, XTi 6002, XTi 2002 User manual

XTi2 Series Power Amplifiers

Front Panel Features

Indicators:

Ready Indicator: Two green LEDs, one for each channel, illuminate when the amplifier is ready to produce audio.

Signal Presence Indicator: Two green LEDs, one for each channel, illuminate when the channel input exceeds -40dBu. Useful for troubleshooting cable runs.

-20 Indicator: Two green LEDs, one for each channel, illuminate when the output signal exceeds -20dB below clip.

-10 Indicator: Two green LEDs, one for each channel, illuminate when the output signal exceeds -10dB below clip.

Clip Indicator: Two red LEDs, one for each channel, illuminate at the threshold of audible distortion.

Thermal Indicator: Two red LEDs, one for each channel, illuminate when thermal compression begins due to excessive temperature conditions.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cooling Vents:

Gain (Level) Controls:

LCD Screen:

Front to rear forced air flow.

Two black rotary level controls,

Backlit liquid crystal display

 

 

 

one for each channel.

shows enabled presets and

 

 

 

 

 

 

speaker processing.

 

 

 

 

 

 

 

 

Power Button & Indicator:

Turns amplifier power on and off. Blue LED will illuminate when power is turned on.

Sel/Prev/Next Buttons:

Three buttons located underneath the LCD screen used to access menu items and front panel lockout.

WARNING: Never connect the output to a power supply, battery or power main. Electrical shock may result.

page 8

Operation Manual

XTi2 Series Power Amplifiers

Back Panel Features

XTi 1002, 2002, 4002

Power Cord Clip:

Mounting points for securing, included power cord clip.

Binding Post Output Jacks:

One pair per channel, accepts banana plugs or

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

bare wire. Note: Binding Post outputs on European

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Input Connector:

 

 

 

 

 

models come with safety plugs installed to prevent

 

 

 

Fans:

 

 

 

 

 

European power plugs from being inserted. The

 

 

 

Two 3-pin XLR input

 

 

 

 

 

side entry positions for these connectors should

 

 

 

Provide front to back

connectors are provided

 

 

 

 

 

be used with European models.

 

 

 

forced airflow for cooling.

(one per channel).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AC Power

4-Pole Speakon® Output Connectors:

 

 

 

 

Connector

These two connectors accept 2-pole and 4-pole

 

 

 

 

 

 

 

 

 

 

 

 

 

Speakon© connectors. The channel 1 connector is

 

 

 

 

 

 

 

 

 

 

 

 

 

wired for both channels so it can be used for

 

 

 

 

 

 

 

 

 

 

 

 

 

bridge-mono wiring or stereo wiring of two

 

 

 

 

 

 

 

 

 

 

 

 

 

speakers to a single Speakon.

Link/Out Connector:

Two 3-pin XLR output connectors are provided (one per channel) to loop-thru signal from one amplifier to another.

HiQnet USB Connector:

Type B USB connector allows you to connect the amplifier to a computer for use with System Architectand Band Managersoftware.

XTi 6002

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Power Cord Clip:

Binding Post Output Jacks:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Mounting points for securing,

One pair per channel, accepts banana plugs or

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

included power cord clip.

bare wire. Note: Binding Post outputs on European

 

 

 

 

 

 

 

Input Connector:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

models come with safety plugs installed to prevent

Fans:

 

 

 

 

 

 

AC Power

European power plugs from being inserted. The

 

Two 3-pin XLR input

 

 

 

 

 

side entry positions for these connectors should

Provide front to back

 

connectors are provided

 

 

 

 

 

Connector

be used with European models.

forced airflow for cooling.

 

(one per channel).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Circuit Breaker:

4-Pole Speakon® Output Connectors:

Provides overload protection

These two connectors accept 2-pole and 4-pole

 

Speakon© connectors. The channel 1 connector is

 

wired for both channels so it can be used for

 

bridge-mono wiring or stereo wiring of two

 

speakers to a single Speakon.

Link/Out Connector:

Two 3-pin XLR output connectors are provided (one per channel) to loop-thru signal from one amplifier to another.

HiQnet USB Connector:

Type B USB connector allows you to connect the amplifier to a computer for use with System Architectand Band Managersoftware.

Operation Manual

page 9

XTi2 Series Power Amplifiers

Front Panel Navigation

From the front panel, you can change settings for several of the amplifier’s integrated signal processing features: Input Y, Crossover Frequency, EQ, Delay, Limiting, and Stereo/Bridge-Mono. The Icons in the display illuminate to show which features are currently applied and turned on.

When you power-on the amplifier for the first time, the LCD screen displays “DSP OFF” (no DSP is applied). Subsequent power-ons display the preset that was active when you last shut off the amplifier.

The figure below shows the Menu Tree, which is the navigation path of options in the Menu. It shows how you navigate through the front panel and which settings are available from the front panel. For full access to all features, it is required that you hook up the amplifier via USB to a computer and run either HiQnet System Architect™ or Band Manager™ software. Both are available free via download from the following address: http://hiqnet.harmanpro.com.

Menu Tree

 

 

 

 

Power-up

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CURRENT PRESET

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Next or Prev

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FLASHING “PRESET” TEXT

 

 

FLASHING “CONFIG” TEXT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sel

 

 

 

 

 

Sel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Next

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FLASHING “PRESET” ICON

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sel

 

DSP PROCESSES

 

 

 

 

 

 

 

 

 

 

 

Press Next to see

 

 

 

 

 

 

 

 

 

 

 

 

(ICONS on screen)

 

 

Next

 

CH1+CH2

 

each processor’s

 

 

 

 

 

 

 

 

 

 

 

 

Y

 

INPUT Y

 

options, then press

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sel

 

STEREO

 

Sel to select an option.

 

 

 

 

PRESETS

 

 

 

 

 

 

 

 

 

 

Next

 

 

 

 

 

 

 

 

 

 

 

 

 

(TEXT on screen)

 

 

 

 

 

 

 

 

 

OFF, 90 Hz, 100 Hz, 1200 Hz,

 

 

 

 

 

 

 

 

 

 

XOV

 

 

 

 

 

 

 

 

 

 

 

1500 Hz, 2000 Hz, 2-CH SUB,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sel

 

CUSTOM

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Next

 

 

 

 

 

 

 

 

 

 

 

 

DSP

OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EQ OUT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EQ Ch. 1

 

 

 

 

 

 

 

 

 

 

 

Next

 

 

 

 

 

 

 

Prev

 

EQ IN

 

 

 

 

 

 

 

 

BRIDGE

 

 

 

 

 

 

 

 

 

 

Sel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Next

 

 

 

 

 

 

 

 

 

 

 

 

 

Next

 

EQ OUT

 

 

 

 

 

 

 

XOVER

 

 

 

 

 

 

 

EQ Ch. 2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Prev

 

EQ IN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Next

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BRG SUBS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Next

 

CURRENT, OFF, 50, 40, 30,

 

 

 

 

 

 

Next

 

 

 

 

 

 

DELAY Ch. 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

20,10, 9, 8, 7, 6, 5, 4, 3, 2, 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sel

 

 

 

 

 

 

 

 

SUB SYNTH

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Next

 

 

 

 

 

 

 

 

 

 

 

 

Next

 

CURRENT, OFF, 50, 40, 30,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DELAY Ch. 2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

USER PRESETS

 

 

 

 

 

 

 

 

 

 

20,10, 9, 8, 7, 6, 5, 4, 3, 2, 1

 

 

 

 

6-50

 

 

 

 

 

 

 

 

 

 

 

Sel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Next

 

 

 

 

 

 

 

 

 

 

 

Next

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CURRENT, OFF, –0.5 dB,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LIM Ch. 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

–1.0 dB, –1.5 dB... –40 dB

 

 

 

 

 

 

Sel

 

 

 

 

 

Sel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Doing nothing returns you to the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Next

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CURRENT, OFF, –0.5 dB,

 

 

CURRENT PRESET after a timeout delay.

 

 

LIM Ch. 2

 

 

 

 

 

 

 

–1.0 dB, –1.5 dB... –40 dB

 

 

Starting from the CURRENT PRESET,

 

 

 

 

 

Sel

 

 

 

 

 

 

 

 

 

 

Next

 

 

 

 

 

 

 

Sel > Sel > Next goes to presets.

 

 

 

 

 

 

 

 

 

 

BRIDGE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

STEREO/BRIDGE MONO

 

 

 

 

 

 

 

 

 

Sel > Next > Sel lets you

 

 

 

 

 

Sel

 

 

 

 

 

STEREO

 

 

 

 

 

 

 

 

 

 

Prev

 

 

 

configure the DSP processes.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Navigating the LCD Screen Menu: Basics

To step through the Menu options, press the Sel, Next or Prev buttons as described in the menu tree above. Icons illuminated at the top of the screen show which DSP functions are active with the current preset.

When you are modifying a preset, its icon flashes. You can scroll through its settings with the Prev and Next buttons.

When you see the desired setting, select it by pressing Sel. Doing nothing returns you to the current preset after ten seconds.

In the LCD screen, if the Preset Icon is lit, the current preset is unchanged from its stored settings. If the Custom Icon is lit, the current preset has been changed from its stored settings.

page 10

Operation Manual

XTi2 Series Power Amplifiers

Integrated Processing Features

The XTi2 Series amplifiers include a number of integrated processing features which appear as icons on the front panel LCD screen. They are described below:

NOTE: System Architect Software is required to have full control over all Integrated Processing Features which can be downloaded from the following URL – http://hiqnet.harmanpro.com/. When controlling more than one XTi2 at a time you will need USB Hub. We recommend using a Powered USB Hub.

Input Mode

t 4UFSFP *O UIJT NPEF $IBOOFM JOQVU HPFT UP $IBOOFM PVUQVU BOE $IBOOFM JOQVU HPFT UP $IBOOFM PVUQVU 5IJT JT the mode the amplifier is configured for from the factory.

t 46. $) $) o *O UIJT NPEF UIF $IBOOFM JOQVU TJHOBM BOE $IBOOFM JOQVU TJHOBM BSF TVNNFE BOE GFE UP CPUI output channels. This provides a 6 dB level boost.

t *OQVU : o *O UIJT NPEF UIF $IBOOFM JOQVU TJHOBM JT TFOU UP UIF $IBOOFM BOE $IBOOFM PVUQVU 5IF DIBOOFM JOQVU signal is ignored.

Output Mode

t 4UFSFP o *O UIJT NPEF UIF BNQMJmFS TFOET $IBOOFM JOQVU TJHOBM UP UIF $IBOOFM PVUQVU BOE UIF $IBOOFM JOQVU TJHOBM to the Channel 2 output.

t #SJEHF .POP o *O UIJT NPEF UIF QPXFS PG CPUI BNQMJmFS DIBOOFMT BSF EFMJWFSFE JOUP B TJOHMF PS PIN MPBE

Subharmonic Synth

The Subharmonic Synth feature takes the low frequencies and “synthesizes” or creates new frequencies that are one octave lower. The two signals are then summed together. Also new, are two user adjustable parametric EQ filters and crossover frequency filter. These can be used to “shape” the sound and enhance the desired effect.

Equalization

The XTi2 Series provides two blocks of equalization in the signal processing. The input EQ block is before the crossover and is usually used for the room EQ. The output EQ block is after the crossover and is usually used for speaking tuning.

Input EQ: This input EQ block provides 6 filters per channel each with frequency, gain, and Q that is user controllable.

This block also has a High and Low Shelf Filter per channel which has gain and frequency control.

Output EQ: This output EQ block provides 8 filters per channel each with frequency, gain, and Q control that is user controllable.

Crossover:

The crossover section provides users with the ability to enable a HighPass and LowPass filter per channel along with BandPass gain and the ability to change the polarity. This allows the Crossover section to be customized to most system configurations.

For the HighPass and LowPass Filters, you have the choice of the following filters: Butterworth 6dB/oct, Butterworth 12dB/oct,

Butterworth 18dB/oct, Butterworth 24dB/oct, Butterworth 48dB/oct, Linkwitz-Riley 24dB/oct, and Linkwitz-Riley 48dB/oct.

The BandPass gain provides you with -15dB to +15dB of gain.

Delay

There is up to 50msec of delay available in the signal processing for time aligning your speakers. The software allows you to enter the amount of delay needed in the form of seconds, feet, or meters and does the calculation for you.

PeakX Plus Limiter:

Feed-forward output limiter with user-adjustable attack, release and threshold (0.1 dB resolution), plus integrated feedback limiter to minimize amplifier clipping.

Operation Manual

page 11

XTi2 Series Power Amplifiers

Integrated Processing Features

Advanced Thermal Control

In this section, you can tailor the fan speed to specific applications. You have the choice of the following modes:

t /PSNBM

t &BSMZ

t 'VMM 4QFFE

The fan mode can be changed using the front panel buttons at start-up or in the software. The default mode is normal and should work fine for most applications. Early mode turns the fan on sooner at a “lower” temperature, and Full-speed mode turns the fan on full-speed full-time. Full-speed mode is not recommended for “dirty” environments.

Advanced Monitoring

This feature allows you to have software visibility of both the Power Supply Temperature and AC Line voltage. AC Line voltage is “derived” from the amplifier rail voltage and is an approximation of the AC line voltage. This allows you to monitor the health of your amplifiers and provides for troubleshooting.

Front Panel Lock-Out

To disable or lock the buttons from the front panel, hold the Prev and Next at the same time until the screen says “locked”.

The rotary knobs (attenuators) will still operate. To unlock, hold Prev and Next until the screen says “unlocked”.

The front panel can also be locked out from the software as well from the main panel. However once it is locked in the software, it can only be unlocked from the software. You cannot unlock from the front panel. The rotary knobs

(attenuators) will still operate.

page 12

Operation Manual

XTi2 Serie Bedienungsanleitung

XTi 1002

XTi 2002

XTi 4002

XTi 6002

DEUTSCH

Weitere Sprachversionen: Um Informationen über die Nutzung dieses Produktes in anderen Sprachen zu erhalten, wenden Sie sich bitte an Ihren örtlichen CrownHändler. Wenn Sie Hilfe dabei benötigen, Ihren örtlichen Händler ausfindig zu machen, kontaktieren Sie Crown bitte unter 574-294-8000.

Dieses Handbuch enthält nicht alle Einzelheiten zu Design, Herstellung oder Varianten des Gerätes. Es deckt auch nicht jeden möglichen Fall ab, der während Installation, Betrieb oder Wartung auftreten könnte.

Die in diesem Handbuch enthaltenen Informationen waren bei Erscheinungsdatum zutreffend. Es können jedoch Aktualisierungen zu diesen Informationen vorliegen. Um die neueste Version dieses Handbuchs zu erhalten, besuchen Sie bitte die Crown-Webseite auf www.crownaudio.com.

Rechtlicher Hinweis: Crown, Crown Audio und Amcron sind eingetragene Handelsmarken von Crown International. Sonstige Handelsmarken sind das Eigentum ihrer jeweiligen Eigentümer. Spätere Versionen dieses Handbuchs und zusätzliche Informationen zu diesem Produkt stehen gegebenenfalls auf der Crown-Webseite auf www.crownaudio.com zur Verfügung.

Einige Modelle können unter dem Namen Amcron® exportiert werden.

©2011 by Harman International, 1718 W. Mishawaka Rd., Elkhart, Indiana 46517-9439 USA, Telefon: 574-294-8000.

143060-2 - 4/11

XTi2 Series Power Amplifiers

Inbetriebnahme

Stereo DSP AUS

Dies ist die Standardwerkseinstellung des Verstärkers. Der Verstärker ist für den Stereomodus konfiguriert, wobei sämtliche Verarbeitungsfunktionen deaktiviert sind.

1.Schließen Sie die rechte/linke Signalquelle mit Hilfe der XLR-Stecker an Kanal 1 und Kanal 2 an

2.Schließen Sie mit Hilfe von Speakon®, Bananensteckern oder blankem Draht einen Lautsprecher an jeden Kanalausgang an

ACHTUNG: Vor Inbetriebnahme Ihres Verstärkers lesen und befolgen Sie bitte die wichtigen Sicherheitsanweisungen, die Sie zu Beginn dieser Bedienungsanleitung finden.

Rückwand des XTi 6002.

Die Rückwände des XTi 1002, 2002 und 4002 finden Sie auf Seite 9.

Werksvoreinstellung Nr. 2: BRÜCKE

Wenn der Verstärker in den BRÜCKEN-Modus (Brücke-Mono) versetzt wird, wird die Leistung beider Verstärkerkanäle als einzelne 8 oder 4 Ohm-

Last bereitgestellt. Die Verstärker der Serie XTi2 sind werkseitig mit einer Voreinstellung versehen, die die Konfiguration des Verstärkers für diesen Betrieb erleichtert.

Bevor Sie beginnen, stellen Sie sicher, dass Sie:

1. die Signalquelle mit Hilfe von XLR-Steckern an Kanal 1 und Kanal 2 angeschlossen haben (die Verstärkereingänge werden automatisch summiert, wenn diese Voreinstellung gewählt wird),

2.den Lautsprecher wie gezeigt angeschlossen haben.

a.Wenn Sie die Verbindungsklemmenausgänge verwenden, schließen Sie die positive Klemme des Lautsprechers an die positive Klemme von Kanal 1 und die negative Klemme des Lautsprechers an die positive Klemme von Kanal 2 an

b.Wenn Sie einen Speakon® Stecker verwenden, schließen Sie die positive Klemme des Lautsprechers an 1+ und die negative Klemme an 2+ an. Stecken Sie den Stecker nur in den Ausgang von Kanal 1 ein

Folgen Sie diesen einfachen Schritten zur Konfiguration des Verstärkers für den BRÜCKEN-Betrieb:

1.Drücken Sie die Taste "Set/Enter", so dass "Preset" blinkt

2.Drücken Sie die Taste "Set/Enter" noch einmal, um die Liste der Voreinstellungen in den Verstärker einzugeben

3.Drücken Sie "Next/Down" oder “PREV/UP”, bis das Display "Bridge" anzeigt

4.Drücken Sie "Set/Enter" zur Bestätigung Ihrer Auswahl

5.Das Display zeigt jetzt "Bridge" an und das Y-Symbol und Brückensymbol sind hervorgehoben

ANMERKUNG: Individuelle Verdrahtungen sind nur von qualifizierten Fachkräften durchzuführen.

page 14

Operation Manual

XTi2 Series Power Amplifiers

Inbetriebnahme

Werksvoreinstellung Nr. 3: XOVER

Im XOVER-Modus wird ein 1,2 kHz Filter der 4. Ordnung (24dB/Oktave) aktiviert, der Frequenzen von 1,2 kHz und weniger an Kanalausgang 1 und Frequenzen von 1,2 kHz und mehr an Kanalausgang 2 sendet. Die Verstärker der Serie XTi2 sind werkseitig mit einer Voreinstellung versehen, die die Konfiguration des Verstärkers für diesen Betrieb erleichtert.

Bevor Sie beginnen, stellen Sie sicher, dass Sie:

1.die Signalquelle mit Hilfe eines XLR-Steckers NUR an Kanal 1 angeschlossen haben (die Verstärkereingänge werden automatisch in den Y-Modus versetzt, wenn diese Voreinstellung gewählt wird),

2.den Lautsprecher wie gezeigt angeschlossen haben.

HIGH 2+/–

LOW 1+/–

a. Schließen Sie mit Hilfe von Speakon®, Bananensteckern oder blankem Draht den Lautsprecher, der die niedrigen und mittleren Frequenzen (1,2 kHz und weniger) empfangen soll, an Kanalausgang 1 an

b.Schließen Sie mit Hilfe von Speakon®, Bananensteckern oder blankem Draht den Lautsprecher, der die hohen Frequenzen (1,2 kHz und mehr) empfangen soll, an Kanalausgang 2 an

Folgen Sie diesen einfachen Schritten zur Konfiguration des Verstärkers für den XOVER-Betrieb:

1.Drücken Sie die Taste "Set/Enter", so dass "Preset" blinkt

2.Drücken Sie die Taste "Set/Enter" noch einmal, um die Liste der Voreinstellungen in den Verstärker einzugeben

3.Drücken Sie "Next/Down" oder “PREV/UP”, bis das Display "BIAMP" anzeigt

4.Drücken Sie "Set/Enter" zur Bestätigung Ihrer Auswahl

5.Das Display zeigt jetzt "BIAMP" an und das Y-Symbol und XOV-Symbol sind hervorgehoben

Werksvoreinstellung Nr. 4: BRG SUBS

Im Modus BRG SUBS (Bridged Subs - überbrückte Subwoofer) können Sie den Verstärker für die Verwendung eines einzelnen 8 oder 4 OhmSubwoofer überbrücken. Die Eingänge werden automatisch summiert, ein 90Hz Tiefpassfilter 4er Ordnung (24 dB/Oktave) wird aktiviert und der Ausgangsmodus wird in den Bridge-Mono-Modus versetzt. Die Verstärker der Serie XTi2 sind werkseitig mit einer Voreinstellung versehen, die die Konfiguration des Verstärkers für diesen Betrieb erleichtert.

Bevor Sie beginnen, stellen Sie sicher, dass Sie:

1. die Signalquelle mit Hilfe von XLR-Steckern an Kanal 1 und Kanal 2 angeschlossen haben (die Verstärkereingänge werden automatisch summiert, wenn diese Voreinstellung gewählt wird),

2. den Lautsprecher wie gezeigt angeschlossen haben.

a.Wenn Sie die Verbindungsklemmenausgänge verwenden, schließen Sie die positive Klemme des Lautsprechers an die positive Klemme von Kanal 1 und die negative Klemme des Lautsprechers an die positive Klemme von Kanal 2 an

b.Wenn Sie einen Speakon® Stecker verwenden, schließen Sie die positive Klemme des Lautsprechers an 1+ und die negative Klemme an 2+ an. Stecken Sie den Stecker nur in den Ausgang von Kanal 1 ein

Folgen Sie diesen einfachen Schritten zur Konfiguration des Verstärkers für den XOVER-Betrieb:

1.Drücken Sie die Taste "Set/Enter", so dass "Preset" blinkt

2.Drücken Sie die Taste "Set/Enter" noch einmal, um die Liste der Voreinstellungen in den Verstärker einzugeben

3.Drücken Sie "Next/Down" oder “PREV/UP”, bis das Display "XOVER" anzeigt

4.Drücken Sie "Set/Enter" zur Bestätigung Ihrer Auswahl

5.Das Display zeigt jetzt "XOVER" an und das Y-Symbol und XOV-Symbol sind hervorgehoben.

Operation Manual

page 15

XTi2 Series Power Amplifiers

Inbetriebnahme

Werksvoreinstellung Nr. 5: SUBSYNTH

Im SUBSYNTH Modus können Sie die SubHarmonic Synth-Funktion zur Verwendung mit einem Subwoofer auf beiden Kanälen aktivieren. Die Eingänge werden automatisch summiert, ein 90Hz Tiefpassfilter 4er Ordnung (24 dB/Oktave) wird sowohl auf Kanal 1 als auch auf Kanal 2 aktiviert und die SubHarmonic Synth-Funktion wird bei einem Pegel

von +12dB aktiviert. Die Verstärker der Serie XTi2 sind werkseitig mit einer Voreinstellung versehen, die die Konfiguration des Verstärkers für diesen Betrieb erleichtert.

Bevor Sie beginnen, stellen Sie sicher, dass Sie:

1. die Signalquelle mit Hilfe von XLR-Steckern an Kanal 1 und Kanal 2 angeschlossen haben (die Verstärkereingänge werden automatisch summiert, wenn diese Voreinstellung gewählt wird),

2.den Lautsprecher wie gezeigt angeschlossen haben

a. Schließen Sie mit Hilfe von Speakon®, Bananensteckern oder blankem Draht einen Lautsprecher an jeden Kanalausgang an Folgen Sie diesen einfachen Schritten zur Konfiguration des Verstärkers für den SUBSYNTH-Betrieb:

1.Drücken Sie die Taste "Set/Enter", so dass "Preset" blinkt

2.Drücken Sie die Taste "Set/Enter" noch einmal, um die Liste der Voreinstellungen in den Verstärker einzugeben

3.Drücken Sie "Next/Down" oder “PREV/UP”, bis das Display "SUBSYNTH" anzeigt

4.Drücken Sie "Set/Enter" zur Bestätigung Ihrer Auswahl

5.Das Display zeigt jetzt "SUBSYNTH" an und das Y-Symbol und XOV-Symbol sind hervorgehoben

Stellen Sie eine korrekte Kühlung sicher

Bei Verwendung eines Rack montieren Sie die Einheiten direkt übereinander. Verschließen Sie Freiräume im Rack mit Blindplatten. Blockieren Sie die Belüftungen an der Vorderund Rückseite NICHT. Die Seitenwände des Rack müssen einen Mindestabstand von 5,1 cm (2 Zoll) zu den Seitenwänden des Verstärkers aufweisen und die Rückseite des Rack muss offen sein.

VORSICHT: Vor der Installation Ihres Verstärkers stellen Sie sicher, dass er von der Stromquelle getrennt ist, der Hauptschalter auf "AUS" steht und alle Pegelregler vollständig zurückgedreht sind (gegen den Uhrzeigersinn).

page 16

Operation Manual

Loading...
+ 36 hidden pages