FT2A-UTK-CLOAK Series
Under-Table Cloak for FT2 Series FlipTop™ Cable Management Solutions
The Crestron® FT2A UTK CLOAK, FT2A UTK CLOAK 1T, FT2A UTK CLOAK WIDE, and FT2A-UTK-CLOAK-WIDE-1T are used to conceal exposed cables and retractors in under-table FT2 Series FlipTop™ applications.
The FT2A UTK CLOAK, FT2A UTK CLOAK WIDE, FT2A UTK CLOAK 1T, and FT2A UTK CLOAK WIDE 1T are functionally similar. For simplicity within this guide, the term “cloak” is used except where noted.
The following information provides compatible FlipTop models and cable retractor types for each cloak.
Cloak Model |
Compatible FT2 Series Model |
|
|
FT2A-UTK-CLOAK |
FT2-202-MECH, FT2-202-MECH-AC, FT2-202-MECH-ACUSB, FT2-500-MECH, |
Conceals up to four gravity retractors. |
FT2-500-MECH-AC, FT2-500-MECH-ACUSB, FT2-700-MECH, FT2-700-MECH-AC, FT2-700- |
|
MECH-ACUSB, FT2-1200-MECH, FT2-1200-MECH-AC, FT2-1200-MECH-ACUSB |
FT2A-UTK-CLOAK-1T |
FT2-202-ELEC, FT2-500-ELEC, FT2-700-ELEC, FT2-1200-ELEC |
Conceals up to four one-touch retractors. |
|
|
|
FT2A-UTK-CLOAK-WIDE |
FT2-1400-MECH, FT2-1400-MECH-AC, FT2-1400-MECH-ACUSB |
Conceals up to four gravity retractors. |
|
|
|
FT2A-UTK-CLOAK-WIDE-1T |
FT2-1400-ELEC |
Conceals up to four one-touch retractors. |
|
|
|
FT2A-UTK-CLOAK |
FT2A-UTK-CLOAK-WIDE-1T |
|||||
|
|
|
Hook-and-loop |
|
Hook-and-loop |
|
|
|
|
fastener strips (4) |
|
fastener strips (4) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
>
*Inside
*Inside
>
Check the Box
Item |
Qty |
|
|
FT2A-UTK-CLOAK, FT2A-UTK-CLOAK-1T, FT2A-UTK-CLOAK-WIDE, or FT2A-UTK-CLOAK-WIDE-1T |
1 |
|
|
Attach the Cloak
Attach the cloak to the FlipTop assembly after the assembly has been installed in the table and the cable retractors and modules are installed in the assembly.
NOTE: Do not fold the cloak. Once creases are made in the fabric, they cannot be removed.
1.Locate the four small strips of hook-and-loop fasteners and remove them from the cloak. These four strips shall be applied to the portion of the FlipTop enclosure that sits beneath the table.
2.Determine the placement of each fastener strip on the FlipTop enclosure. The top of the power supply bracket may be used as a guideline around the enclosure for fastener placement.
NOTE: A minimum of two strips of hook-and-loop fasteners must be used. If only two strips are needed for the installation, place a strip on the front power supply bracket and on the rear of the of the enclosure. These strips are outlined in blue in the illustration.
Recommended hook-and-loop fastener placement
Hook-and-loop |
Power supply |
fastener strip |
bracket |
Power supply |
Hook-and-loop |
bracket |
fastener strips (4) |
3.Remove the protective backing from the fastener strips, and press them firmly onto the FlipTop enclosure.
4.Align the inside of the cloak with the hook-and-loop fasteners to the fastener strips applied to the FlipTop enclosure.
5.Carefully wrap and press the cloak onto the fastener strips attached to the FlipTop enclosure.
Hook-and-loop fastener strips
FlipTop enclosure
Power supply bracket
Cloak
6. To prevent tangling or cable movement obstruction, ensure that the cables are routed properly within the cloak.