Page 1
DO GUIDE
*Use either screw hole for the included 6-32 x 1/2" Phillips
pan head screw.
DM-RMC-200-S/DM-RMC-200-S2
DigitalMedia 8G™ Fiber Receiver and Room Controller
DO Install the Device
The Crestron® DM-RMC-200-S and DM-RMC-200-S2 mount
onto a 2-gang electrical box using the included support
bracket. The support bracket provides a holder for the included
power pack.
Mounting the Device onto an Electrical Box
To mount the device onto an electrical box, do the following:
1. Attach the four included 6-32 x 1-1/4" standoffs to the
studs of the included support bracket.
4. Using the four included 6-32 x 1/4" Phillips head screws,
attach the device to the standoffs.
2. Using the four included 6-32 x 3/4" combo truss head
screws, attach the included suppor t bracket to the
electrical box.
DO Check the Box
QTY PRODUCT COLOR PART NUM.
1 Bracket, Support 2047591
2 Connector, 2-Pin 20 03574
4 Connector, 2-Pin 2003582
2 Connector, 4-Pin 20 03576
1 Connector, 5-Pin 2003577
1 Power Cord, 5' 10" (1.78 m) 2042043
1 Power Pack, 24 Vdc 2.5 A, 100-240 Vac 2045873
1 Screw, 6-32 x 1/2", Pan Head, Phillips Black 2007238
4 Screw, 6-32 x 1/4", Pan Head, Phillips Black 2007215
4 Screw, 6-32 x 3/4", Truss Head, Combo 2 0 0 9211
4 Standoff, 06-32 x 1-1/4", 1/4" OD, Hex 2007056
2 Tie Wrap, Cable Tie, 15-1/2" x 1" Black 2013 608
c. Repeat steps 3a and 3b if necessary using the other
included tie wrap and the remaining tie wrap hole in
the power pack holder.
Screw
hole*
Tie wrap
hole
3. Ground the device and then connect the proper cables to
the bottom of the unit.
Ground
RELAY:
To relay
controllable
devices
AUDIO OUT:
Amplied stereo
audio output
DIG IN:
Software
programmable
digital input
Inserting the Power Pack
into the Power Pack Holder
To insert the power pack into the power pack holder, do the
following:
1. Slide the power pack into the power pack holder.
2. Using the included 6-32 x 1/2" Phillips pan head screw,
thread the screw through either of the two provided
screw holes to hold the power pack in place.
3. Bundle the excess cable of the power pack into a loop,
and then fasten the bundled cable to the power pack
holder by doing the following:
a. Insert one of the included tie wraps through one of
the tie wrap holes in the power pack holder.
b. Wrap the tie wrap around the bundled cable.
Tie wrap
Screw
hole
hole*
Installation of the power pack in the holder appears as shown
below.
Page 2
DO Complete the Connections
or other DM device
HDMI OUT:
Make additional connections as appropriate for the application.
DM-RMC-200-S and DM-RMC-200-S2
Front Panel Connections
HDMI® digital
video/audio
DIG IN:
software
programmable
digital input
output
From USB
HID-compliant
RS-232 device
USB HID:
device
COM:
To/from
IR:
To IR
controllable
device
DM-RMC-200-S Rear Panel Connections
AUDIO OUT R, L
(SPEAKER):
Amplied stereo
audio output
AUDIO OUT R, L (LINE):
Stereo unbalanced
line level audio output
DM IN MMF/SC:
From DM
®
switcher, transmitter,
LAN:
10BASE-T/100BASE-TX
Ethernet to local
network device
24 V 2.0A MAX:
From power pack
(included)
DM-RMC-200-S2 Rear Panel Connections
DO Set the IP Address
The conguration of the receiver within the DigitalMedia 8G™
system determines how the IP address of the receiver is set:
• If the receiver connects to a DigitalMedia™ switcher, the
receiver is congured by the switcher automatically.
• If the receiver connects to a DigitalMedia 8G ber
transmitter, the receiver uses its own conguration
settings. By default, DHCP (Dynamic Host Conguration
Protocol) is enabled. If it is desired, assign the default IP
address to the receiver by holding down the SETUP button
while the unit boots up. The default IP address overwrites
the current setting. The default IP address of the DMRMC-200-S and DM-RMC-200-S2 is 192.168.1.248.
To manually set a different IP address, use Crestron
Toolbox™ application.
AUDIO OUT R, L
(SPEAKER):
Amplied stereo
audio output
10BASE-T/100BASE-TX
Ethernet to local
network device
AUDIO OUT R, L (LINE):
Stereo unbalanced
line level audio output
DM IN SMF/LC:
From DM switcher, transmitter,
or other DM device
As of the date of manufacture, the products have been tested a nd found to comply with specications for CE mar king.
This product is Listed to applicable UL Standards and requirements by Underwri ters Labora tories Inc.
Ce produit est homologué selon les normes et les exige nces UL applicables par Underwr iters L abor atories Inc.
Federal Communications Commission (FCC) Compliance Statement
This device complies with par t 15 of the FCC Rules. Op eration is subj ect to the following two conditio ns:
(1) This devic e may not cause harmful in terference, and (2) this device must accept any i nterference rece ived, includin g inter feren ce
that may cause undesired operation.
CAUTION: Changes or modication s not expressly approve d by the manufacturer re spons ible for compli ance could void t he
user’s authority to operate the equipme nt.
NOTE: This equipm ent has been tested and f ound to co mply with the limits for a Cl ass A dig ital device, pu rsuant to par t 15 of
the FCC Rul es. These limi ts are de signe d to provide reasonable protec tion against harmful inter feren ce when the equipment
is operated in a co mmerc ial environme nt. Thi s equip ment ge nerates, use s, and ca n radiate radio freque ncy ene rgy and, if not
installed and used in accord ance wi th the ins truction man ual, may c ause ha rmful i nterference to radio communications. Op eration
of this equipment in a residential area i s likely to c ause ha rmful interferenc e in whic h case th e user will be required to c orrect the
inter ference at his own expense.
LAN:
DM-RMC-200-S
DO Learn More
24 V 2.0A MAX:
From power pack
(included)
Industry Canada (IC) Compliance Statement
CAN ICES-3(A)/NMB-3(A)
The products a re clas s 1 laser products. They comply with safety re gulations of IEC -60 825-1, FDA 21 CFR
1040 11 and FDA 21 CFR 1040 10.
WARNING: Visible and invisi ble las er radi ation when open. Avoid direct exposure to b eam.
NOTE: Plug the included dust cap into the optical tran sceive r when the ber optic cable is unplugged.
WARNING: These are Class A pr oducts. In a domestic e nvironment these products m ay cause radio interfe rence in which c ase the
user may b e requi red to take adequate meas ures.
The speci c patents that c over Crestron pro ducts are listed a t patents.crestron.com. The produ ct warranty ca n be found at www.crestron.com/warranty.
Certa in Crestron pro ducts contain op en source soft ware. For speci c information, ple ase visit www.crestron.com/opensource.
Crestr on, the Cre stron log o, Crest ron Toolbox, D igitalM edia, Digi talMedi a 8G, and DM a re either t rademark s or regist ered trad emarks of C restron E lectro nics, Inc. i n the United S tates
and/or ot her countr ies. HDM I and the HDMI logo ar e either tr ademarks o r register ed tradema rks of HD MI Licens ing LLC in th e United S tates and /or other countries . UL and the U L logo are
either tr ademarks or registe red trademarks of U nderwriters L aboratories, In c. in the United Stat es and/or other coun tries. Other tra demarks, register ed trademarks, and t rade names may be
used in this d ocument to refer to eit her the entities cla iming the marks and name s or their products . Crestron discla ims any proprietar y interest in the mar ks and names of other s. Crestron is
not respo nsible for errors in t ypography or ph otography.
This docum ent was written by t he Technical Publicat ions departmen t at Crestron.
©2016 Crestron Electronics, Inc.
Visit the website for additional information and the
latest rmware updates. To learn more about this
product, use a QR reader application on your mobile
device to scan the QR images.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
DM-RMC-200-S2
DO GUIDE
DOC. 7810 B (20 444 21) 09.16
Specic ations subject to c hange without not ice.
Loading...