Project |
|
Catalog # |
|
Type |
|
Prepared by |
|
Notes |
|
Date |
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
WaveLinx Wired |
||||
|
|
|
|
FLT-DAC-DALI-DC1 & |
||||
|
|
|
|
FLT-DAC-DALI-DC2 |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
DAC - Digital to Analog Converter |
||||
|
|
|
|
Typical Applications |
||||
|
|
|
|
Office • Education • Healthcare • Hospitality • Retail • |
||||
|
|
|
|
Industrial • Manufacturing |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
Product Certification |
||||
|
Interactive Menu |
|
|
|||||
|
|
|
|
|
|
|
|
|
|
• Ordering Information page 2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• Additional Resources page 3 |
|
|
|
|
|
|
|
|
• Wiring Diagrams page 4 |
|
|
Product Features |
||||
|
• Connected Systems page 5 |
|
|
|||||
|
|
|
|
|
|
|
|
|
|
• Product Warranty |
|
|
WaveLinx Wired |
Tuning |
|||
|
|
|
|
|||||
|
|
|
|
Local Bus |
Control |
|||
|
|
|
|
|||||
Top Product Features
•Built-in latching relay and 0-10V current sinking interface
•All DAC’s device settings configured through the software
•Automatic detection of WaveLinx Wired Local Bus loss of power for Emergency lighting control (UL924)
•Available for Class 1 or Class 2 wiring configurations
•Ultra-low profile form factor designed
Dimensional Details
Side View Angled View
1.125”
(28.58mm)
1.0” |
1.0” |
(25.4mm) |
(25.4mm) |
3.94” |
3.94” |
(100.0mm) |
(100.0mm) |
additional product diagrams
PS503276EN page 1
December 2020
WaveLinx Wired |
Digital to Analog Converter |
||
Order Information |
|
|
|
|
|
|
|
|
|
|
|
Catalog Number |
|
|
|
|
|
|
|
Catalog Number |
|
Description |
|
|
|
|
|
FLT-DAC-DALI-DC1 |
Digital to Analog Converter - wiring exits with line voltage wiring for Class 1 installations of the two wire communications bus. |
|
|
|
|
|
|
FLT-DAC-DALI-DC2 |
Digital to Analog Converter - wiring exits with line voltage wiring for Class 2 installations of the two wire communications bus. |
|
|
|
|
|
|
Product Specifications
Key Features
•Built-in latching relay and 0-10V current sinking interface used to integrate individual or a group of dimmable 0-10V ballasts/drivers
•All DAC’s device settings (fade, scenes and groups) configured through the software, eliminating the need for manual adjustments
•Automatic detection of the WaveLinx Wired Local Bus power loss with default to closed and full bright (100% lighting)
•Available for Class 1 or Class 2 wiring configurations
•Ultra low profile form factor designed to fit inside driver/ballast compartment of most standard luminaires
•Easily mountable to fixture housing through standard knockout using supplied 90° elbow and mounting clip
•Powered by the WaveLinx Wired Local Bus (via SCMD4). Line in and load out connection to driver/ballast, neutral & ground connection are not required.
Mechanical
Dimensions: 1”H x 3.94”W x 1.125”L (25.4mm x 100mm x 28.6mm)
Mounting:
•In fixture or junction box mounting only.
Refer to Wiring Diagram section of spec sheet for proper wiring details.
Enivironment:
•Temperature: 32°F to 140°F (0°C to 60°C)
•Relative Humidity: 10% to 90% (non-condensing). For indoor use only.
Electrical
Relay Output:
•Input Voltage: 120-480 VAC +/- 10%
•Maximum Ballast/General Load for operating temperature lower than 104F: 4.5A @ 120-480 VAC
•Maximum Ballast/General Load for operating temperature higher than 104F: 3A @ 120-480VAC
•Maximum Tungsten Load: 8A @ 120 VAC, 5.8A @ 240 VAC
•Input Frequency: 50/60 Hz
Control Specification:
•Communication Interface: WaveLinx Wired Local Bus (topology, polarity free)
•Current Draw: 3.75mA
•Analog Dimming Current Draw: 0-10 VDC, 50mA max current sink only
Note: Upon first power up allow 4-6 seconds before sending commands
Wiring:
•Relay: 18 AWG solid TFN non-polarized pair
•0-10V Dimming: 18 AWG solid TFN polarized pair
•Communication: 18 AWG stranded PTGE plenum rated non-polarized pair
Standards/Ratings
•cULus Listed - Energy Management Equipment (UL916)
•Manufactured in an ISO 9001 certified factory
•Meets ASHRAE Standard 90.1 requirements
•Meets IECC 2015 requirements
•Meets CEC Title 24 requirements
Warranty
Five year warranty standard
Overview
The Digital to Analog Converter (DAC) is a lighting control device used to control any standard 0-10V current sourcing dimmable ballast/driver. It allows dimming control by sending 0-10V dimming and on/off commands to the DAC via the WaveLinx Wired Local Bus.
PS503276EN page 2
December 2020
Loading...