Cooper Lighting L908, L906, L905, L986, L907 User Manual

...
0 (0)
Cooper Lighting L908, L906, L905, L986, L907 User Manual

L 9 0 4 L C o n n e c t o r

To connect two track sections at a right angle. Field adjustable for either right hand or left hand application. May be used as feed point.

Finish: White (P), Black (MB)

L 9 0 6 X C o n n e c t o r

To connect four track sections into a cross configuration. May be used as feed point.

Finish: White (P), Black (MB)

L 9 0 8 M i n i J o i n e r

A low profile connector to cleanly and crisply join two straight track sections end-to-end. (Note: The L908 is not a feed point).

Finish: White (P), Black (MB)

L 9 5 0 C o r d a n d P l u g C o n n e c t o r

12’ three-wire cord with grounded plug. Maximum capacity 10 AMP

Finish: White (P), Black (MB)

L 9 7 9 C o n d u i t C o n t i n u a t i o n K i t

Consisting of one left feed and one right feed.

To continue a run around obstructions. Designed to accept 1/2” trade size conduit fitting (not included).

Finish: White (P), Black (MB)

L 9 8 3 T- B a r A t t a c h m e n t C l i p

Allows track to be attached to inverted tee ceiling. Order as follows: 2 kits for 2’ Trac; 2 kits for 4’ Trac; 3 kits for 8’ Trac and 4 kits for 12’ Trac.

L 9 8 6 M i n i - T B a r C l i p

For mounting Trac on suspended ceilings with mini-grid (9/16” wide) system.

L 9 9 4 4 5 ° P e n d a n t A d a p t e r

For installing pendant mounted Power-Trac on sloped ceiling. For use with L992 and L993.

Finish: White (P), Black (MB)

HALO®

L 9 0 5 T C o n n e c t o r

To connect three track sections into a T configuration. Field adjustable for either right hand or left hand application. May be used as feed point.

Finish: White (P), Black (MB)

L 9 0 7 O u t l e t B o x f o r u s e w i t h T- B a r c e i l i n g

L901, L903, L904, L905 or L906 connector also required. 4”x 4” x 1 1/8”.

Finish: White (P), Black (MB)

L 9 0 9 F l o a t i n g C a n o p y a n d

C o n n e c t o r

Track can be connected to existing outlet

box located anywhere along the track. Comes with canopy cover, connector, dead-end and mounting hardware. 4 1/8” x 4 1/4” x 1 3/8”.

Finish: White (P), Black (MB)

L 9 5 1 W i r e W a y C o v e r f o r P e n d a n t A s s e m b l y K i t

For track to be wired through stem (order one for each feed point used). Shown with end feed and pendant stem kit–order separately

Finish: White (P), Black (MB)

L 9 8 0 L i v e E n d C o n d u i t A d a p t e r

Designed to accept standard 1/2” trade size conduit fitting (not supplied). Use when feeding to track through surface conduit system.

Finish: White (P), Black (MB)

L 9 9 2 P e n d a n t K i t A s s e m b l y

Order 2 kits for 2’ Trac; 2 kits for 4’ Trac; 3 kits for 8’ Trac; and 4 kits for 12’ Trac. Includes one 18” threaded steel stem, canopy and mounting hardware.

L 4 8 4 8 ” S t e e l S t e m

For additional length with L992. Can be field cut.

Finish: White (P), Black (MB)

D E 6 0 0 D e a d E n d

Replacement Dead Ends for Single Circuit Track (6 included)

Finish: White (P), Black (MB)

Circuit Single LIGHTING TRACK

COOPER LIGHTING 311

Loading...