L 9 0 4 L C o n n e c t o r
To connect two track sections at a right angle. Field adjustable for either right hand or left hand application. May be used as feed point.
Finish: White (P), Black (MB)
L 9 0 6 X C o n n e c t o r
To connect four track sections into a cross configuration. May be used as feed point.
Finish: White (P), Black (MB)
L 9 0 8 M i n i J o i n e r
A low profile connector to cleanly and crisply join two straight track sections end-to-end. (Note: The L908 is not a feed point).
Finish: White (P), Black (MB)
L 9 5 0 C o r d a n d P l u g C o n n e c t o r
12’ three-wire cord with grounded plug. Maximum capacity 10 AMP
Finish: White (P), Black (MB)
L 9 7 9 C o n d u i t C o n t i n u a t i o n K i t
Consisting of one left feed and one right feed.
To continue a run around obstructions. Designed to accept 1/2” trade size conduit fitting (not included).
Finish: White (P), Black (MB)
L 9 8 3 T- B a r A t t a c h m e n t C l i p
Allows track to be attached to inverted tee ceiling. Order as follows: 2 kits for 2’ Trac; 2 kits for 4’ Trac; 3 kits for 8’ Trac and 4 kits for 12’ Trac.
L 9 8 6 M i n i - T B a r C l i p
For mounting Trac on suspended ceilings with mini-grid (9/16” wide) system.
L 9 9 4 4 5 ° P e n d a n t A d a p t e r
For installing pendant mounted Power-Trac on sloped ceiling. For use with L992 and L993.
Finish: White (P), Black (MB)
HALO®
L 9 0 5 T C o n n e c t o r
To connect three track sections into a T configuration. Field adjustable for either right hand or left hand application. May be used as feed point.
Finish: White (P), Black (MB)
L 9 0 7 O u t l e t B o x f o r u s e w i t h T- B a r c e i l i n g
L901, L903, L904, L905 or L906 connector also required. 4”x 4” x 1 1/8”.
Finish: White (P), Black (MB)
L 9 0 9 F l o a t i n g C a n o p y a n d
C o n n e c t o r
Track can be connected to existing outlet
box located anywhere along the track. Comes with canopy cover, connector, dead-end and mounting hardware. 4 1/8” x 4 1/4” x 1 3/8”.
Finish: White (P), Black (MB)
L 9 5 1 W i r e W a y C o v e r f o r P e n d a n t A s s e m b l y K i t
For track to be wired through stem (order one for each feed point used). Shown with end feed and pendant stem kit–order separately
Finish: White (P), Black (MB)
L 9 8 0 L i v e E n d C o n d u i t A d a p t e r
Designed to accept standard 1/2” trade size conduit fitting (not supplied). Use when feeding to track through surface conduit system.
Finish: White (P), Black (MB)
L 9 9 2 P e n d a n t K i t A s s e m b l y
Order 2 kits for 2’ Trac; 2 kits for 4’ Trac; 3 kits for 8’ Trac; and 4 kits for 12’ Trac. Includes one 18” threaded steel stem, canopy and mounting hardware.
L 4 8 4 8 ” S t e e l S t e m
For additional length with L992. Can be field cut.
Finish: White (P), Black (MB)
D E 6 0 0 D e a d E n d
Replacement Dead Ends for Single Circuit Track (6 included)
Finish: White (P), Black (MB)
Circuit Single LIGHTING TRACK
COOPER LIGHTING 311
L 9 4 2 F l e x J o i n e r
To connect two track sections at any angle up to 90,° in either plane or wall to ceiling or pitched ceiling applications.
Finish: White (P), Black (MB)
L 9 4 5 R R i g h t T C o n n e c t o r
“T” connector for joining three trac sections with right hand polarity. May be used as feed point.
Finish: White (P), Black (MB)
L 9 4 6 X C o n n e c t o r
To connect four track section into a cross configuration. May be used for feed point.
Finish: White (P), Black (MB)
L 9 4 9 M i n i J o i n e r
To join two straight track sections end-to-end. Not a feed point.
Finish: White (P), Black (MB)
L 9 8 3 T- B a r A t t a c h m e n t C l i p
Allows track to be attached to inverted tee ceiling. Order as follows: 2 kits for 2’ Trac; 2 kits for 4’ Trac; 3 kits for 8’ Trac; and 4 kits for 12’ Trac.
L 9 8 6 T- B a r A t t a c h m e n t C l i p
For mounting track on suspended ceilings with mini-grid (9/16" wide) system.
L 9 2 9 F l o a t i n g C a n o p y a n d C o n n e c t o r
Can be connected anywhere along length of Trac. Comes with canopy cover, connector, dead-end and mounting hardware.
Finish: White (P), Black (MB)
L 9 9 4 4 5 ° P e n d a n t A d a p t e r
For installing pendant mounted Power-Trac on sloped ceiling. For use with L992 and L993.
Finish: White (P), Black (MB)
HALO®
L 9 4 3 S t r a i g h t / L C o n n e c t o r
To connect two track sections end-to-end or at a 90° angle. May be used as feed point.
Finish: White (P), Black (MB)
L 9 4 5 L L e f t T C o n n e c t o r
“T” connector for joining three trac sections with left hand polarity. May be used as feed point.
Finish: White (P), Black (MB)
L 9 4 7 C o n d u i t C o n n e c t o r
A live end connector for use with surface conduit. Designed to accept standard 1/2” conduit fitting (not included). May be used for feed point.
Finish: White (P), Black (MB)
L 9 5 1 W i r e W a y C o v e r f o r
P e n d a n t A s s e m b l y K i t
For track to be wired through stem (one for each live end used). Shown with end feed and pendant stem kit–order separately
Finish: White (P), Black (MB)
L 9 8 9 C o n d u i t C o n t i n u a t i o n K i t
Includes one left and one right feed. To continue
a run around obstructions with 1/2” trade size surface conduit.
Finish: White (P), Black (MB)
L 9 9 2 P e n d a n t K i t A s s e m b l y
To suspend track from ceiling. Order as follows: 2 kits for 2’ Trac; 2 kits for 4’ Trac; 3 kits for 8’ Trac; and 4 kits for 12’ Trac. Includes one 18” threaded steel stem, canopy and mounting hardware.
Finish: White (P), Black (MB)
L 4 8 4 8 ” S t e e l S t e m
For additional length of stem for L992. Can be field cut and threaded.
D E 6 4 1 D e a d E n d
Replacement Dead Ends for Two Circuit Track (6 included)
Finish: White (P), Black (MB)
Circuit Two LIGHTING TRACK
COOPER LIGHTING 313
Loading...