Compaq MV 540 User Manual

User's Guide

Guia do Usuário

Manuel de l'utilisateur

Guía de Usuario

MV540

TABLE OF CONTENTS

INTRODUCTION ...........................................................................................................................	2
Features............................................................................................................................................................	2
GETTING STARTED......................................................................................................................	3
Attaching the Base Pedestal to Your Monitor......................................................................................................	3
Installation ........................................................................................................................................................	4
Speaker Installation ...................................................................................................................................	5
OPERATING YOUR MONITOR .......................................................................................................	6
Using Your On-Screen Display ...........................................................................................................................	7
No Signal Message............................................................................................................................................	8
Out of Frequency Range ....................................................................................................................................	8
On-Screen Display Functions .....................................................................................................................	9
ENERGY SAVER MODES ............................................................................................................	10
MONITOR CARE AND MAINTENANCE.........................................................................................	11
TROUBLESHOOTING..................................................................................................................	12
SHIPPING YOUR MONITOR.........................................................................................................	14
SPECIFICATIONS .......................................................................................................................	15
APPENDIX .................................................................................................................................	16
Regulatory Compliance Notices .......................................................................................................................	16
Federal Communications Commission Notice ...........................................................................................	16
Modifications ...........................................................................................................................................	16
Cables .....................................................................................................................................................	16
Declaration of Conformity for products marked with the FCC logo - United States only .............................	16
Canadian Notice.......................................................................................................................................	17
Avis Canadien..........................................................................................................................................	17
European Union Notice.............................................................................................................................	17
EPA Energy Star Compliance....................................................................................................................	17
Japanese Notice ......................................................................................................................................	17
German Ergonomics Notice......................................................................................................................	17

1

INTRODUCTION

Congratulations on the purchase of your new, easy-to-use Compaq MV540 Color Monitor. The MV540 is a state-of-the-art, high performance monitor featuring a 15-inch (13.8-inch/350.5 mm viewable image area) screen. The user-friendly On-Screen Display allows you to make quick and easy adjustments to your screen image.

Features

•15-inch monitor with a large, 13.8-inch/350.5 mm viewable image area to comfortably view applications

•.28mm dot pitch to produce crisp, sharp images

•On-screen user controls for easy adjustment of the screen image

•Quick, easy setup

•Energy Star compliant for reduced power consumption

•Integrated microphone for all of your Internet, telephony, and multimedia applications

•Attachable or standalone JBL Platinum Series amplified speakers

−Integrated audio input jack for MP3 players and other portable audio devices

−Integrated headphone jack

2

GETTING STARTED

Your Compaq MV540 Color Monitor packaging should include the following:

•Monitor

•Power cord

•Microphone cable

•Speakers and speaker power cable or adapter (selected models)

•Speaker stands

•User documentation

•Setup poster

CAUTION: Do not place your monitor face down. Damage could result to the front panel controls or to your monitor screen.

Attaching the Base Pedestal to

Your Monitor

For shipping purposes, the base pedestal is not connected to your monitor. To attach it, proceed as follows:

1.Turn your monitor so that it is resting on the top.

2.Place the base pedestal in corresponding slots, then push it toward the front panel until it clicks and secures in place.

3

Installation

Before installing your monitor, place it in a convenient, well-ventilated location near your computer, ensure that power to your computer and other peripheral devices is turned off, and proceed as follows:

1.Insert the speaker power cable or adapter plug 1 into the back of the right speaker . Insert the plug from the left speaker into the socket on the back of the right speaker .

2.Insert the other end of the speaker power cable 3c into the back of the monitor .

3.Connect the lime green plug from the right speaker 2 to the audio out socket on the back of your computer.

4.Connect the pink end of the microphone cable to the microphone socket on the back panel of your monitor 3b, then plug the other end of the cable into the microphone connector on the rear panel of your computer 6.

5.Connect the monitor signal cable from the back of the monitor to the blue socket on the back of the computer 4. Tighten the screws on the end of the connector.

IMPORTANT: Ensure that the signal cable aligns with the 15-pin connector. Do not force the cable onto the connector or you may damage the signal cable.

(Installation instructions continued on next page.)

4

6.Connect the power cord to the back of the monitor 3a, then connect the power cord to a power outlet 5.

WARNING: To reduce the risk of electric shock or damage to your equipment, do not disable the power cord grounding feature. This equipment is designed to be connected to a grounded (earthed) power outlet that is easily accessible to the operator. The grounding plug is an important safety feature.

WARNING: For your safety, be sure that the power outlet you plug your power cord into is easily accessible and located as close to the equipment operator as possible. When you need to disconnect power to the equipment, unplug the power cord from the power outlet by grasping the plug firmly. Never pull on the cord.

CAUTION: For the protection of your monitor as well as your computer, connect all power cords for your computer and its peripheral devices (monitor, printer, scanner, and so on) to some form of surge protection such as a power strip or UPS (Uninterruptible Power Supply).

Not all power strips provide surge protection; they must be specifically labeled as having this ability. Look for manufacturers that have a Damage Replacement Policy to replace your equipment if their surge protection fails.

7.Install your speakers using one of the methods listed in “Speaker Installation”.

8.Power on your monitor by pressing the power button 7. Power on the speakers by pressing the power button on the side of the right speaker.

If necessary, adjust the front panel controls according to your personal preference.

Your monitor installation is now complete.

Speaker Installation

Headphone/Audio Input Jacks

Retractable Speaker Mechanism

Speaker Stand

Insert the headphone connector	1.	Rotate the thumbwheel up to extend	Insert the speaker stand into the slot on
(headphones not included) into the		the hook mechanism.	the rear of each speaker.
headphone jack.	2.	Align the hooks with the slots on the
Insert one end of the cable from		monitor, then gently insert the hooks
		into the slots and slide down to lock in
your portable audio device (not
		place.
included) into the speaker.

5

OPERATING YOUR MONITOR

Front Panel Controls

Reference	Icon	Icon Name	Function
1		Backward button	Backward button (left arrow) moves backward through menu
			options or decreases adjustment levels.
		Select button	•	Launches On-Screen Display
2			•	Selects functions and adjustments
			•	Exits menus and On-Screen Display
3		Forward button	Forward button (right arrow) moves forward through menu
			options or increases adjustment levels.
		Power LED	•	Green light—indicates power on
			•	Yellow light—indicates Standby/Suspend mode
4			•	Amber light—indicates Sleep mode
			For more information on power states, see "Energy Saving
			Modes."
5		Power button	Turns the monitor on and off.

6

Using Your On-Screen Display

The On-Screen Display (OSD) adjusts the screen image based on your viewing preferences. To access the On-Screen Display, do the following:

1.If your monitor is not already on, press the power button to turn it on. (For the location of front panel control buttons, see “Front Panel Controls” in the previous section).

2.Press the Select button to display the On-Screen Display menu.

3.To select a function, press the Forward or Backward button until the function is highlighted.

4.Press to choose the function.

5.An adjustment window is displayed. Use the Forward and Backward button to increase (Forward) or decrease (Backward) the level of adjustment.

6.Press to save the new adjustment.

7.To exit the On-Screen Display, select the Exit icon, then press the Select button once.

7

No Signal Message

If a “NO SIGNAL” message displays on your monitor, check to be sure your VGA cable is properly connected, and ensure that your computer is powered on.

Out of Frequency Range

If an “OUT OF FREQUENCY RANGE” message appears on your screen, your video resolution and/or refresh rate are set higher than what your monitor supports. To correct this problem, follow the steps below or contact your Compaq authorized dealer, reseller, or service provider.

1.Restart your computer.

2.Press F6 before Microsoft® Windows® begins to load so that you can enter Safe Mode.

3.Change your display settings to a supported setting (see “Specifications”).

4.Restart your computer so that the new settings take effect.

8

On-Screen Display Functions

Your On-Screen Display (OSD) menu accesses the following functions:

							On-Screen Display Functions
On-Screen Display								Function
						Contrast		Adjusts display contrast
						Brightness		Adjusts display brightness
						H. Position		Shifts display right or left
						H. Size		Increases and decreases display width
						V. Position		Shifts display up or down
						V. Size		Increases and decreases display height
						Pincushion		Adjusts the concave and convex portion of the picture
						Trapezoid		Adjusts the top and bottom display widths to make them even
						Degauss		Demagnetizes screen to reduce color impurities
						Parallelogram		Adjusts the tilt of the display sides to the left or right
						Reset		Resets monitor to factory default values
						Exit		Exits OSD menu

9

ENERGY SAVER MODES

Your monitor has been designed to meet strict EPA (Environmental Protection Agency) Energy Star requirements for reduced power consumption and to comply with the VESA Standard Display Power Management Signal. Using a combination of hardware and software functions, this energy-saving feature allows the computer to control your monitor’s power consumption and reduce your monitor’s power state when not in use.

NOTE: Power consumption does not include the speaker power.

IMPORTANT: Your monitor’s energy saver feature works only when your monitor is connected to a computer that also has energy saver features.

The following table describes your monitor energy saver levels in each of four power states.

Power Management States

State	LED Color	Power	Description
		Consumption
ON	Green	<80 watts	Normal operation
STANDBY/	Yellow	<15 watts	Monitor screen is blank. High voltage is off. Heater
SUSPEND			voltage is reduced. Full power mode returns quickly
			(approximately 4 seconds).
SLEEP	Amber	<5 watts	Monitor screen is blank. High voltage is off. Heater
			voltage is off. There is a brief warm-up period before
			returning to full power mode
			(approximately 15 seconds).

The energy saver features, of the energy saver utility, are available with the Microsoft® Windows® operating system. Some features are also available in DOS. Refer to your computer’s user guide for instructions on setting energy saver features (may also be referred to as power management features).

10

MONITOR CARE AND MAINTENANCE

To enhance the performance and extend the life of your monitor, use the following guidelines:

•Do not open your monitor cabinet or attempt to service this product yourself. Adjust only those controls that are covered in the operating instructions. If your monitor is not operating properly or has been dropped or damaged, contact your Compaq authorized dealer, reseller, or service provider.

•Place your monitor at least 3 inches (76 mm) away from walls or other enclosures.

•Use only a power source and connection appropriate for your monitor, as indicated on the label on the back plate.

•When you connect your monitor to an outlet or extension cord, be sure the total ampere rating of the products connected to the outlet does not exceed the current rating of the electrical outlet, and the total ampere rating of the products connected to the cord does not exceed the rating of the cord.

•Install your monitor near an outlet that you can easily reach. Disconnect your monitor by grasping the plug firmly and pulling it from the outlet. Never disconnect your monitor by pulling the cord.

•Turn your monitor off when not in use. You can substantially increase the life expectancy of your monitor by using a screen saver program for brief idle times and turning off your monitor when it is not in use for an extended period of time.

•Unplug your monitor from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. If the screen requires additional cleaning, use an antistatic CRT screen cleaner.

CAUTION: Do not use benzene, thinner, ammonia, or any other volatile substances to clean your monitor or the screen. These chemicals may damage the cabinet finish as well as the screen.

•Slots and openings in the cabinet are provided for ventilation. These openings must not be blocked or covered. Never push objects of any kind into cabinet slots or other openings.

•Do not place plants on top of your monitor. Water or dirt from the plant may get into the vents.

•Do not drop your monitor or place it on an unstable surface.

•Do not allow anything to rest on the power cord. Do not walk on the cord.

•Keep your monitor in a well-ventilated area, away from excessive light, heat and moisture. Keep your monitor away from high-capacity transformers, electric motors, and other devices with strong magnetic fields.

•In a two-monitor system, place your monitors as far apart from one another as possible to lessen interference between them.

11

TROUBLESHOOTING

You may save time and money by solving common monitor problems using the following simple, easy- to-apply solutions. If you are unable to solve the problem using these troubleshooting solutions, visit the Compaq website at www.compaq.com/athome or contact your Compaq authorized dealer, reseller, or service provider.

Problem	Possible Cause	Solution
Screen is blank	Power cord disconnected	Connect the power cord
	Power switch off	Turn on power
	Signal cable improperly	Connect signal cable properly
	connected
	Screen blanking utility is active	Depress any key on the keyboard or move the
		mouse
Image appears blurred,	Brightness and contrast are	Press	to access the On-Screen Display (OSD),
indistinct, or too dark	too low	then select the brightness			and/or contrast
		icon to adjust to desired levels*
Color is abnormal	A magnetic object may	Move the object farther away
	be nearby
	Monitor has been moved or	Press	to access the OSD, then select Degauss
	inadvertently bumped	to activate*
Image is too large or too small	Horizontal width may need	Press	to access the OSD, then select
	adjustment	H. Size		to adjust*
	Vertical height may need	Press	to access the OSD, then select
	adjustment	V. Size		to adjust*
Image is not centered	Horizontal position needs	Press	to access the OSD, then select
	adjustment	H. Position		to adjust*
	Vertical position needs	Press	to access the OSD, then select
	adjustment	V. Position		to adjust*
“No Signal” is displayed	Monitor signal cable is not	Connect the 15-pin monitor signal cable to the
on screen	connected to the computer	computer. Be sure that computer power is on.
“Out of Range” is displayed on	Video resolution and/or refresh	Restart your computer, press F6 before Microsoft
screen	rate are set higher than what	Windows begins to load so that you enter Safe
	your monitor supports	Mode. Change your settings to a supported setting
		(see “Specifications”). Restart your computer so
		that the new settings take effect.
*Refer to the “Using Your On-Screen Display” section for detailed instructions.					(continued)

12

Troubleshooting (continued)

Problem	Possible Cause	Solution
No speaker power	Speaker power plug may have	Check all speaker power connections and ensure
	come unplugged	they are properly connected
	Power button on right-side	Push the power button on the right side of the right
	speaker may be off	speaker; power button should illuminate
No sound from speakers	Speaker audio plug may have	Make sure your audio input jack (lime green
	come unplugged from the back	connector) is plugged into the back of your
	of the computer	computer
	Mute button on keyboard may	Push the mute button on your keyboard or click on
	be activated	the speaker icon located on your Windows desktop
		and deselect “Mute”
	Volume level may be adjusted	Increase the volume level by using your keyboard
	too low	volume control or clicking on the speaker icon
		located on your Windows desktop and increasing
		the volume level
No sound from left speaker	Speaker connection from left	Make sure the speaker connection from the left
	speaker may have come	speaker is plugged into the rear of the right
	unplugged	speaker
	Left speaker balance may need	Click on the speaker icon located on your Windows
	to be adjusted	desktop and adjust the Left-Right balance
		accordingly
Integrated microphone is	Microphone cable is not	Ensure that the microphone cable is connected
not working	connected properly	properly
Monitor is overheating	There is not enough ventilation	Leave at least 3 inches (76mm) of ventilation
	space to allow proper airflow	space surrounding your monitor, and do not place
		objects on top of your monitor

13

SHIPPING YOUR MONITOR

In the event you need to ship your monitor, keep the original packing box.

If you find it necessary to remove the base pedestal for shipping or service reasons, please refer to the instructions and illustration below for proper removal.

1.Release the catch and slide the base pedestal toward the back of your monitor.

2.Lift the base pedestal up and away from your monitor.

14

SPECIFICATIONS

	Compaq MV540 Color Monitor
Monitor Type		Color, multi-frequency, digital controls
Picture Tube		15-inch Flat Square, Polished or Anti-glare
Viewable Image Area		13.8" (350.5mm)
Operating Temperature		50°F – 86°F (10°C – 30°C)
Relative Humidity		20% – 80%
Dot Pitch		.28mm
Display Resolutions		Refresh Rates
1024 x 768		60 Hz (maximum resolution)
800 x 600		85 Hz (maximum flicker-free resolution)
800 x 600		75 and 60 Hz
720 x 400		70 Hz
640 x 480		85, 75 and 60 Hz
640 x 400		70 Hz
Input Impedance		75 +/- 3 % Ohms
Horizontal Frequency		30 kHz – 54 kHz
Vertical Frequency		50 Hz – 120 Hz
Universal Power Supply		90 – 132 V, 50 – 60 Hz
		190 – 265 V, 50 – 60 Hz
Inrush Current		30 amps @ 120 V
		60 amps @ 220 V
Maximum Power Rating		<80 watts
Signal Cable		15-pin miniature D-sub
Speakers (selected models)		Attachable, amplified JBL Platinum Series
Speaker Frequency Response		100 Hz – 20 kHz
Speaker Watts		3W RMS per channel max. at 10% THD
Microphone		Integrated
Dimensions (LxWxH) Unpacked		16.3" x 14.5" x 15.6"
		(413 mm x 368 mm x 397 mm)
Weight
Unpacked monitor only		28.7 lb. (13 kg)
Packed in box (Monitor and Speakers)		38.5 lb. (17.5 kg)
Power Management		Yes
Energy Star Compliant		Yes
MPRII Compliant		Yes (selected models)
TCO99 Compliant		Yes (selected models)
European Union CE Compliant		Yes (selected models)
Plug and Play		Yes

15

APPENDIX

Regulatory Compliance Notices

Federal Communications Commission Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna

•Increase the separation between the equipment and receiver

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

•Consult the dealer or an experienced radio or television technician for help

Modifications

The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Compaq Computer Corporation may void the user's authority to operate the equipment.

Cables

Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods in order to maintain compliance with FCC Rules and Regulations.

Declaration of Conformity for products marked with the FCC logo - United States only

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

For questions regarding your product, contact:

Compaq Computer Corporation

P. O. Box 692000, Mail Stop 530113

Houston, Texas 77269-2000

Or, call

1-800-652-6672 (1-800-OK COMPAQ)

16

For questions regarding this FCC declaration, contact:

Compaq Computer Corporation

P. O. Box 692000, Mail Stop 510101

Houston, Texas 77269-2000

Or, call [phone]

To identify this product, refer to the Part, Series, or Model number found on the product.

Canadian Notice

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Avis Canadien

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

European Union Notice

Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community.

Compliance with these directives implies conformity to the following European Norms (in brackets} are the equivalent international standards:

•EN55022 (CISPR 22) - Electromagnetic Interference

•EN50082-1 (IEC801-2, IEC801-3, IEC801-4) - Electromagnetic Immunity

•EN60950 (IEC950) - Product Safety

•EN60555-2 (IEC555-2) - Power Line Harmonics

EPA Energy Star Compliance

Monitors that are marked with the ENERGY STAR Logo meet the requirements of the EPA ENERGY STAR program. As an ENERGY STAR Partner, Compaq Computer Corporation has determined that this product meets the ENERGY STAR guidelines for energy efficiency. Specific details on using the Energy Saving features can be found in the energy saver or power management section of the computer manual.

Japanese Notice

German Ergonomics Notice

Compaq Computers, when tested with the Compaq Monitors, were evaluated and found compliant to the requirements of ZH 1/618 (German Safety Regulations for Display Work Places in the Office Sector) in the Text Mode (720 × 400) using MS-DOS Version 3.31 (or higher) and BASICA as published by Compaq Computer Corporation.

17

18

ÍNDICE

INTRODUÇÃO ............................................................................................................................	20
Recursos.........................................................................................................................................................	20
INICIANDO.................................................................................................................................	21
Montando o Pedestal Base em seu Monitor .....................................................................................................	21
Instalação .......................................................................................................................................................	22
Instalação do Auto-falante .......................................................................................................................	23
COMO OPERAR SEU MONITOR ..................................................................................................	24
Como Usar Seu On-Screen Display..................................................................................................................	25
Mensagem No Signal ......................................................................................................................................	26
Mensagem Out of Frequency Range ................................................................................................................	26
Funções On-Screen Display .....................................................................................................................	27
MODOS DE ECONOMIA DE ENERGIA..........................................................................................	28
CUIDADOS E MANUTENÇÃO DO MONITOR.................................................................................	29
RESOLUÇÃO DE PROBLEMAS....................................................................................................	30
TRANSPORTE DO MONITOR ......................................................................................................	32
ESPECIFICAÇÕES ......................................................................................................................	33
APÊNDICE .................................................................................................................................	34
Avisos sobre compatibilidade regulatória.........................................................................................................	34
Aviso do FCC (Federal Communications Commission)...............................................................................	34
Modificações ...........................................................................................................................................	34
Cabos ......................................................................................................................................................	34
Declaration of Conformity for products marked with the FCC logo - United States only .............................	34
Canadian Notice.......................................................................................................................................	35
Avis Canadien..........................................................................................................................................	35
European Union Notice.............................................................................................................................	35
EPA Energy Star Compliance....................................................................................................................	35
Japanese Notice ......................................................................................................................................	35
German Ergonomics Notice......................................................................................................................	35

19

INTRODUÇÃO

Parabéns por adquirir seu novo e fácil de usar Monitor Colorido Compaq MV540 O MV540 é um monitor estado da arte e de alto desempenho apresentando uma tela de 15 polegadas

(13,8 pol/350,5 mm de área útil vísivel). O On-Screen Display amigável permite que você faça ajustes rápidos e fáceis na imagem de sua tela.

Recursos

•Monitor de 15-pol com uma área de imagem grande, 13,8por/350,5 mm, para exibir confortavelmente suas aplicações.

•Dot pitch .28mm para produzir imagens nítidas e claras.

•Controle de usuário na tela para ajustes fáceis na imagem exibida.

•Configuração fácil e rápida.

•Compatível com Energy Star para consumo reduzido de energia.

•Microfone integrado para todas suas aplicações Internet, de telefonia e multimídia.

•Auto-falantes amplificados JBL Platinum Series anexados ou autônomos.

−Conector de entrada de áudio integrado para MP3 players e outros dispositivos de áudio portáteis.

−Conector de fone de ouvido integrado.

20

INICIANDO

A embalagem de seu Monitor Colorido Compaq MV540 deve incluir o seguinte:

•Monitor

•Cabo de alimentação

•Cabo do microfone

•Auto-falantes e cabo de alimentação dos auto-falantes ou adaptador (alguns modelos)

•Bases dos auto-falantes

•Documentação do usuário

•Cartaz de configuração

Montando o Pedestal Base em seu Monitor

Para fins de transporte, o pedestal da base não vem conectado ao monitor. Para anexá-lo, faça o seguinte:

1.Vire o monitor de cabeça para baixo.

2.Coloque o pedestal da base nas fendas correspondentes e, em seguida, empurre- a em direção ao painel frontal até que se encaixe e se trave no lugar.

ATENÇÃO: Não coloque seu monitor de cabeção para baixo. Pode resultar em danos nos controles do painel frontal ou na tela de seu monitor.

21