Compaq JP1, JP2, PL-P3-SMP User Manual

0 (0)
www.powerleap.com www.friendtech.com
-1-
Installation Guid
e
PowerLeap PL-P3/SMP
Installation Guide
Slot 1 Server/Workstation CPU Upgrade Adapter
Before You Start…
Check the website of your sy stem or motherb oard ma nufa cturer to see if t hey are
offering an updated BIOS version for your system. If you need to upgrade your
system BIOS, do so before removing your old CPU.
For more information about BIOS upgrades, refer to “Upgrading Your Computer’s
BIOS” later in this document.
Update your computer’s sound and video drivers.
Select the frontside bus speed and dual CPU pin signal by configuring jumper
settings on the PL-P3/SMP.
Unplug your system and remove the cover.
PL-P3/SMP Jumper Settings
JP1 & JP2: Frontside Bus (FSB) Speed
JP1 JP2
1 1
2 2
3 3
66MHz
JP1 JP2
1 1
2 2
3 3
Auto-Detect (default)
JP1 JP2
1 1
2 2
3 3
100MHz
JP1 JP2
1 1
2 2
3 3
133MHz
Note: This setting depends on the motherboard circuitry des i gn: some VIA 694
chipset-based SMP m otherboards can only work stably at 100MHz, not 133MHz.
JP3: Dual CPU Signal
JP3
1 2
3 4
5 6
BR1# pin
JP3
1 2
3 4
5 6
BR1-X2 pin
JP3
1 2
3 4
5 6
BR1-N33 pin (default)
JP3
1 2
3 4
5 6
Single CPU
What is the PowerLeap PL-P3/SMP?
The PowerLeap PL-P3/SMP™ provides an
economical CPU upgrade path for
dual-CPU Slot 1 (Pentium II™- and
Pentium III™-based) servers/workstations.
With the innovative PL-P3/SMP, you can
obtain significantly faster performance (up
to 1.4GHz) from your server/workstation by
upgrading to Intel Pentium III-S™
("Tualatin" core, 512KB L2 cache)
p
rocessors. The PL-P3/SMP™ also
supports the Intel Pentium III 1.13/1.2GHz
and Celeron 1.0A~1.4GHz CPU for
single-CPU operation.
www.powerleap.com www.friendtech.com
-2-
Installation Guid
e
Installation
Installing the PL-P3/SMP™ is quick and easy: First, remove the original processors from the motherboard’s
processor slots. Next, insert a processor into the PL-P3/SMP™, apply thermal compound to the processor, and
install the heatsink/fan. Finally, install the PL-P3/SMP™ into the motherboard’s processor slot and make power
connections.
Removing the original processors from the CPU slots
The original Slot 1 processors. Be
sure to disconnect the system
power before continuing with your
processor upgrade.
After removing one of the original
processors (for details, refer to your
motherboard manual).
After removing both original
processors. We recommend using a
small brush to remove any dust from
the slots.
Inserting a processor, applying thermal compound, and installing the heatsink/fan
Before installing the processor in the
PL-P3/SMP.
Installing the processor in the
PL-P3/SMP. (1)
Installing the processor in the
PL-P3/SMP. (2)
The PL-P3/SMP with installed
processor.
Applying thermal compound to the
processor.
The processor after applying thermal
compound.
Loading...
+ 4 hidden pages