Clarion XN3410, XN3210 Manual

0 (0)

Owner’s manual & Installation manual Mode d’emploi et manuel d’installation Manual de instrucciones y de instalación

XN3210 XN3410

XN AMPLIFIERS AMPLIFICATEURS XN AMPLIFICADORES XN

INTRODUCTION

The Clarion XN3210 is a full-featured, two-channel amplifier incorporating the

 

following features:

 

Specially coated circuit boards that resists mold, mildew and moisture damage.

 

Pulse-Width Modulated (PWM) MOSFET power supply for maximum

 

 

performance with minimal distortion.

English

Remote turn-on with "soft start" muting to prevent turn-on "thump".

 

slope (adjustable range: 55Hz to 5.5kHz).

Variable high-pass/low-pass electronic crossover with a 12dB per octave

 

Variable bass boost circuit to reinforce low frequency signals that may be lost

 

 

due to subwoofer enclosure design.

Owner’s

 

and distortion.

Adjustable input level controls with ground loop isolation to minimize noise

 

2-ohm stereo stable, 4-ohm mono stable.

Manual

Chrome-plated power, speaker and RCA connections.

 

Speaker level input.

 

Low profile construction with aluminum heat sink for efficient heat dissipation.

 

The Clarion XN3410 is a full featured, four-channel amplifier adding the following feature:

Advanced circuitry design featuring bridgeable and mixed mode operation for use in various system configurations including 4, 3, or 2 channel systems.

ABOUT THE MANUAL AND WARRANTY

This manual describes the basic requirements to install the Clarion XN3210 and XN3410 amplifiers. The installation of this amplifier can be quite complex to install. If you do not posses the necessary knowledge and tools to perform this installation, please contact your local Clarion Marine Audio dealer.

Keep all instructions and sales receipt for future reference and warranty information. Warranty information can be found on page 19 of this manual.

TABLE OF CONTENTS

Description . . . . . . . . . . . . . . . . . . . . . . .

.

4

Input Connections and Audio Controls . . . . . . . . . . . . .

 

4

Connections for Power and Speakers . . . . . . . . . . . . .

 

6

Installation . . . . . . . . . . . . . . . . . . . . . . .

.

8

Mounting Precautions . . . . . . . . . . . . . . . . . . .

.

8

Wiring Precautions . . . . . . . . . . . . . . . . . . . .

.

8

XN3410 Wiring and Applications . . . . . . . . . . . . . . .

 

9

XN3210 Wiring and Applications . . . . . . . . . . . . . . .

.

14

Setting the Gain . . . . . . . . . . . . . . . . . . . . . . 17

Setting the Crossover . . . . . . . . . . . . . . . . . . . . 17

Setting the Subwoofer Bass Boost . . . . . . . . . . . . . .

.

17

Final System Check . . . . . . . . . . . . . . . . . . . .

 

18

Troubleshooting . . . . . . . . . . . . . . . . . . . . .

.

18

Product Specs . . . . . . . . . . . . . . . . . . . . . .

 

19

XN3210/XN3410

Manual Owner’s English

DESCRIPTION

The XN3210 and XN3410 use an unregulated MOSFET power supply for superior sound and output wattage. In addition, a toroid-coil is used to transfer power with minimal performance loss due to heat. To avoid unwanted noise, a doublesided conformal printed circuit board with strategically placed components keeps AM RFI subdued.

All of the connections and controls for the XN3210 and XN3410 are conveniently located at the ends of the amplifier and labeled appropriately. To ensure the best possible electrical connections, the power, speaker, and RCA inputs are goldplated. An additional benefit of the XN3410 is the ability to create a 2, 3, or 4 channel amplified system with a flip of a switch (see Application section). In the event of component failure or a short circuit, the XN3210 and XN3410 incorporate safe guards and outboard ATC fuses to prevent damage to the amplifier.

INPUT CONNECTIONS AND AUDIO CONTROLS

The front panel of the XN3410 and XN3210 contain both connections for RCA and speaker level inputs, along with the audio controls as shown below.

Fig. 1

XN3410

2

3

4

5

6

7

8

9

16

1

11

12

13

14

15

10

 

1.

CH1-CH2 High Input

9.

CH3/4 Mode Switch

2.

CH1/CH2 RCA Input

10.

CH3-CH4 High Input

3.

CH3/CH4 RCA Input

11.

CH1/2 Frequency Control

4.

CH1/CH2 Gain Control

12.

CH1/2 Crossover Mode Switch

5.

CH3/4 Gain Control

13.

CH3/4 Frequency Control

6.

Bass Boost

14.

Frequency Range Multiplier

7.

Source Select

15.

CH3/4 Crossover Mode Switch

8.

CH1/2 Mode Switch

16.

Power Light Indicator

XN3210/XN3410

XN3210

1

2

3

4

5

6

7

9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

 

 

 

 

 

 

 

 

 

 

 

 

 

1. CH1-CH2 RCA Input

6. Crossover Mode Switch

2.

Gain Control

7.

Output Mode Selector Switch

3.

Bass Boost

8.

High Input

4. CH1/CH2 Frequency Control

9.

Power Light Indicator

5.

Frequency Range Multiplier

 

 

 

 

 

 

 

 

 

 

 

 

The RCA connections are gold plated for optimum performance and low signal loss. The RCA connectors are labeled CH1 (front left), CH2 (front right) [for XN3410: CH3 (rear left), and CH4 (rear right)]. In applications where RCA signals are not present, the speaker level output from the head unit can be used. (Use one or the other input, not both.)

Gain Controls: For the XN3410, separate CH1/2 and CH3/4 gain controls

allow you to set the nominal operating level of the amplifier. The amplifier's input range, 200mV to 6.0V for RCA inputs and 500mV to 13V for speaker level inputs, can accommodate input levels from virtually any head unit.

Bass Boost: The amplifier features a "high-Q" (i.e. narrow frequency band)

Bass Boost circuit. It acts much like an equalizer with an adjustable gain from 0 to +15dB fixed at 45Hz. Use this feature to tune low-frequency audio response to compensate for a less than ideal subwoofer enclosure design. The added boost produces rich, full bass tones that are normally difficult to reproduce in the marine audio environment.

NOTE: Bass Boost setting should only be used for subwoofer applications.

Source Select (XN3410 only)

2CH BASS: Uses CH1/2 inputs and has output from all 4 channels with Bass Boost.

2CH: Uses CH1/2 inputs and has output from all 4 channels. The Bass Boost will work only on CH1/2 and have no effect on CH3/4.

4CH: Uses all 4 channel inputs and has output from all 4 channels. The Bass Boost will work only on CH1/2 and have no effect on CH3/4.

Manual Owner’s English

XN3210/XN3410

Manual Owner’s English

Output Mode Selector Switch: CH 1/2 and CH 3/4 (XN3410 only)

STEREO: Full left and right stereo operation.

CH1Mono / CH2 Mono: Single channel input for bridged operation. This is especially useful in high-powered systems. (Uses CH2 and CH4 inputs.)

CH1/2 Mono / CH3/4 Mono: Allows for a stereo input to be summed into a mono output.

CH1/2 FREQ / CH3/4 FREQ (XN3410 only) The CH1/2 crossover frequencies are adjustable from 55Hz to 550Hz. While CH3/4 crossover frequencies are adjustable from 55Hz to 5500Hz (via the Frequency Range Multiplier) for a wider range of crossover points. Use this feature along with your speaker manufacturer's recommended crossover frequencies to quickly design a more advanced system.

NOTE: If either of the Crossover Mode Switches is set to OFF, varying the frequency control will have no effect.

CH1/2 Filter / CH3/4 Filter (XN3410 only) A filter is activated by sliding the

CH1/2 and CH3/4 filter switch to either HP = High Pass or LP = Low Pass. CH1/2 is fully adjustable from 55-550Hz (via CH1/2 Freq) and CH3/4 is fully adjustable from 55-5500Hz (via CH3/4 Frequency and Frequency Range Multiplier). Use this feature along with your speaker manufacture's recommended crossover frequencies to design a more advanced system.

CONNECTIONS FOR POWER AND SPEAKERS

The rear panel of the XN3410 and XN3210 contains power and speaker connections as shown below.

Fig. 2

XN3410

 

1

 

 

2

 

3

4

5

6

 

 

4

Ω BRIDGED

 

 

 

 

 

 

+

CH1

+

CH2

GND

REM

+12V

 

 

 

 

 

 

 

 

 

 

FUSE

 

 

 

 

 

 

 

 

30A

30A

+ CH3 –

+ CH4 –

4 Ω BRIDGED

7

8

 

1. CH1 Speaker Output

5. Battery +12V Input

2. CH2 Speaker Output

6. (2) - 30 Amp Fuse

3. Ground

 

7. CH3 Speaker Output

4. Remote Turn-on

 

8. CH4 Speaker Output

XN3210/XN3410

Clarion XN3410, XN3210 Manual

XN3410 - Electrical Connection

 

 

 

 

 

 

 

 

Remote Turn-On

F

 

 

 

 

 

 

 

 

 

 

 

U

 

 

 

 

 

 

 

 

 

 

 

S

 

 

 

 

 

 

 

 

 

 

 

E

 

 

 

 

 

4 Ω BRIDGED

 

 

 

 

 

 

 

 

+

CH1

+

CH2

GND

REM

+12V

 

 

 

 

 

 

 

 

 

 

 

FUSE

 

 

 

 

 

 

 

 

 

 

 

30A

30A

 

 

+

CH3

+

CH4

 

 

 

 

 

 

 

 

4 Ω BRIDGED

 

 

 

 

 

 

CH1 Speaker (+)

 

 

 

 

 

 

 

CH4 Speaker (-)

 

 

CH1 Speaker (-)

 

 

 

 

 

CH4 Speaker (+)

 

 

 

CH2 Speaker (+)

 

 

 

 

CH3 Speaker (-)

 

 

 

CH2 Speaker (-)

 

 

CH3 Speaker (+)

 

 

 

Fig. 3

 

 

 

 

 

 

 

 

 

 

 

XN3210

 

 

 

 

 

 

 

 

 

 

 

1

 

2

 

 

 

3

 

4

5

6

 

 

4 Ω BRIDGED

 

 

 

GND

REM

+12V

 

 

 

 

 

 

 

 

FUSE

 

+ L

+ R –

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

40A

 

1. Left Speaker Output

4. Remote Turn-on

2. Right Speaker Output

5. Battery

 

3. Ground

6. 40 Amp Fuse

XN3210 - Electrical Connection

 

 

 

 

 

Remote Turn-On

F

 

 

 

U

 

 

 

S

 

 

 

E

4 Ω BRIDGED

GND REM

+12V

 

 

+ L –

+ R –

 

FUSE

 

 

 

40A

Left Speaker (-)

Right Speaker (-)

Left Speaker (+)

Right Speaker (+)

Manual Owner’s English

XN3210/XN3410

Loading...
+ 12 hidden pages