Citizen ANA-DIGI 30-7XXX, ANA-DIGI JMOXXX User Manual

0 (0)

CITIZEN QUARTZ

ANA-DIGI

Model No. 30-7XXX, JMOXXX

Cal. No. C20 , C480, T011

• INSTRUCTION MANUAL

CTZ-6751

1. SELECTING BASIC FUNCTIONS

Press M button to select functions.

TIME ALARM STOPWATCH CALENDAR

3. ADJUSTING THE DIGITAL TIME DISPLAY

TIME

SECONDS

MINUTES

HOURS

12/24 HOURS

TIME

1.Press M button to set to the normal TIME display

2.Press S button until SECONDS start flashing.

3.Press R to set seconds to “00”.

4.Press S for MINUTES adjustment. MINUTES start flashing.

5.Press R and adjust the minutes.

6.Press S for Hours adjustment. HOURS start flashing.

7.Press R and adjust the hours.

8.Press S for 12/24 HOURS selection. 12/24 HOURS starts flashing.

9.Press R and select 12 or 24-HOUR display.

10.Press S or M to finalise adjustment. The watch returns to the normal TIME display.

Alarm, Stopwatch and calendar modes are indicated by each flashing mode mark.

Crown – Analog display set,

M – Mode change, Instant manual returnS – Selection, Reset, Split

R – Adjustment, Start, Stop, Alarm Set,

Illumination

The Cal. C20 doesn’t have any STOPWATCH or CALENDAR mode mark.

2. ADJUSTING THE ANALOG DISPLAY

Pull out the crown one step and turn clockwise or counterclockwise direction to adjust the analog time display. The seconds hand will start timekeeping synchronising with the digital time display when the crown is returned to the original position.

If the watch is left in the adjustment mode for about one minute without operating any buttons, AUTO RETURN will activate to return to the normal TIME display.

If seconds adjustment is made when the SECOND display is showing 30-59 seconds, the MINUTE display will automatically advance to the next minute.

INSTANT MANUAL RETURN to the normal time display can be made at any stage of adjustment by pressing M button.

A and P marks display only under the 12-hour time system.

Citizen ANA-DIGI 30-7XXX, ANA-DIGI JMOXXX User Manual

4. SETTING AND USING THE ALARM

The setting procedure of the ALARM time is the same as that of the TIME display. Setting order is as follows: ALARM•HOURS MINUTES

The HOURS display will synchronise with the selection of 12 or 24 HOURS in the TIME adjustment.

If the watch is left in the adjustment mode for more than 1 minute without operating any button, AUTO RETURN will activate to return to the normal ALARM display.

INSTANT MANUAL RETURN to the normal ALARM display can be made at any stage of adjustment by pressing M button.

Press R button in the normal ALARM mode to set “ON” or “OFF” the alarm. The ALARM set mark will be indicated.

ALARM sounds for 20 seconds at the ALARM set time. Alarm buzzer can be ceased by pressing any button.

5. USING THE STOPWATCH

Stopwatch operation diagram

Confirmation sound will be made each time S orR button is pressed in the STOPWATCH mode.

The SPLIT COUNTER mode will turn into the STOPWATCH COUNTER mode when it is changed to the other mode while it is in operation.

The TIMEKEEPING of the stopwatch will be turned off, if the ALARM buzzer is stopped by pressing S or R button when the watch is in the STOPWATCH COUNTER or SPLIT COUNTER mode.

While the split display is in use the SPLIT mark or S mark is displayed.

SPLIT TIME measures the time elapsed after starting the split time function.

The stopwatch measurement capacity is 60 minutes, from 0 to 59' 59.99".

6. ADJUSTING THE CALENDAR

 

 

 

1. Press M button to set to

CALENDAR

 

 

 

 

the normal CALENDAR

 

 

 

 

 

 

 

 

 

display.

DATE

 

 

2. Press S until DATE starts

 

 

 

 

flashing.

 

 

 

3.Press R and adjust the date.

MONTH

 

4. Press S for MONTH

 

adjustment. MONTH starts flashing.

5.Press R and adjust the month.

 

 

 

6. Press S

for DAY

DAY

 

 

 

 

adjustment. DAY starts

 

 

 

 

 

 

 

 

 

flashing.

 

7.Press R and adjust the day.

8.Press S or M to finalise adjustment. The watch returns to the normal CALENDAR display.

INSTANT MANUAL RETURN and AUTO RETURN system will activate in the same manner as described in the TIME adjustment.

If non-existent date is set, the CALENDAR display will show the 1st day of the next month when returned to the normal display.

(ex: February 31 March 1)

The CALENDAR function includes automatic month-end adjustment, but in the leap year changeover for February to March must be made manually.

(The Cal C20 doesn’t display the CALENDAR mode mark.)

7. SETTING THE CHIME AND SOUND MONITOR

Press S and R button simultaneously in the normal TIME or normal CALENDAR mode, the CHIME can be set “ON” or “OFF” each time the buttons are pressed and the CHIME set mark will be indicated. The SOUND MONITOR is conducted at the same time when the buttons are pressed.

Loading...
+ 2 hidden pages