GETTING STARTED GUIDE
Cisco ME 3400E Ethernet Access Switch Getting Started Guide
INCLUDING LICENSE AND WARRANTY
1About this Guide, page 2
2Taking Out What You Need, page 2
3Initial Setup, page 5
4Managing the Switch through the CLI, page 8
5Rack-Mounting the Switch, page 9
6Connecting to the Switch Ports, page 12
7In Case of Difficulty, page 13
8Obtaining Documentation and Submitting a Service Request, page 15
9Cisco 90-Day Limited Hardware Warranty Terms, page 15
This guide provides instructions on how to install and configure your Cisco Metro Ethernet (ME) 3400E Ethernet Access switch. Also covered are switch management options, basic rack-mounting procedures, port and module connections, power connection procedures, and troubleshooting help.
For additional installation and configuration information, see the Cisco ME 3400E switch documentation on Cisco.com. For system requirements, important notes, limitations, open and resolved bugs, and last-minute documentation updates, see the release notes, also on Cisco.com.
When you use the online publications, refer to the documents that match the Cisco IOS software version that is running on the switch. Look on the switch rear panel to locate the software version or enter the show version command from the command-line interface (CLI).
Before you set up your switch, and to see translations of safety warnings, review the warnings in the Regulatory Compliance and Safety Information for the Cisco ME 3400E Ethernet Access Switch on the documentation CD or Cisco.com.
1.Unpack and remove the switch and the accessory kit from the shipping box.
2.Return the packing material to the shipping container, and save it for future use.
3.Verify that you have received the items shown in the “Shipping Box Contents” section on page 3. If any item is missing or damaged, contact your Cisco representative or reseller for instructions. Some switch models might include additional items, and you might need to supply or to order some optional items.
You need:
•PC
•RJ-45-to-DB-9 adapter cable (if you did not order one with your switch)
•Ethernet (Category 5) straight-through cable (as shown)
2
The items shipped with your switch depend on the switch model, the options that you choose, and the type of power-supply module. Some items shown are optional, and your switch might look different.
These items ship with the Cisco ME 3400E-24TS-M and the Cisco ME 3400EG-12CS-M switches:
|
|
|
Ethernet |
|
|
|
|
|
|
|
|
Do |
Cisco |
ME |
|
|
|
Doc |
|
|
|
Acce |
ss |
40 |
|
|
|
|
|
cument |
|
3 |
0E |
||
|
|
|
|
|
|
|
||
u |
|
|
|
|
|
|
||
C |
men |
|
|
ationSwi |
||||
D |
tatio |
n |
|
|
|
|
tch |
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
1 |
2 |
|
3 |
4 |
5 |
6 |
|
7 |
|
8 |
9 |
10 |
11 |
|
|
|
|
|
|
|
|
|
1 |
Cisco ME 3400E switch |
7 |
|
Cable guide |
|
|
|
|
|
|
|
|
|||
2 |
Documentation |
8 |
|
Four number-8 Phillips machine screws |
|||
|
|
|
|
|
|||
3 |
AC power cord |
9 |
|
Four number-12 Phillips truss-head screws |
|||
|
|
|
|
|
|
||
4 |
Power cord bail and bushing |
10 |
|
Six number-8 Phillips flat-head screws |
|
||
|
|
|
|
|
|
||
5 |
DC terminal block |
11 |
|
One black Phillips machine screw |
|
||
|
|
|
|
|
|
|
|
6 |
Two 19-inch mounting brackets |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
281098
3
These items ship with the Cisco ME 3400EG-2CS-A switch:
|
|
|
|
EthernCisco |
ME |
|
||
D |
|
|
|
et |
|
|
||
oc |
|
|
DocumAcc |
|
3400E |
|||
|
|
|
en |
|
ess |
|||
|
|
umenta |
|
tatio |
|
Switch |
||
|
CD |
ti |
|
|
n |
|||
|
|
|
|
o |
|
|
|
|
|
|
|
|
n |
|
|
|
|
1 |
2 |
3 |
4 |
5 |
|
7 |
|
8 |
9 |
10 |
281099 |
|
6 |
|
|
|
|
|
1 |
Cisco ME 3400E switch |
6 |
Cable guide |
|
|
|
2 |
Documentation |
7 |
Four number-10 Phillips truss-head screws |
|
||
3 |
AC power cord |
8 |
Four number-12 Phillips truss-head screws |
|
||
4 |
Four rubber feet |
9 |
Two number-10 Phillips flat-head screws |
|
||
5 |
Two 19-inch mounting brackets |
10 |
One black Phillips machine screw |
|
Translations of these warning statements and a complete list of warnings that are applicable to this switch appear in the
Regulatory Compliance and Safety Information for the Cisco ME 3400E Ethernet Access Switches document that shipped with your switch.
Warning |
Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and |
|
|
|
watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld |
|
|
the metal object to the terminals. Statement 43 |
|
|
|
|
|
|
Warning |
Do not stack the chassis on any other equipment. If the chassis falls, it can cause severe bodily injury and |
|
|
|
equipment damage. Statement 48 |
|
|
|
This warning applies to only the Cisco ME 3400E-24TS-M and the Cisco ME 3400EG-12CS-M switches:
Warning |
Before performing any of the following procedures, ensure that power is removed from the DC circuit. |
|
Statement 1003 |
|
|
4
Warning |
To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to |
|
ensure that the system remains stable. The following guidelines are provided to ensure your safety: |
•This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
•When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack.
•If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack.
Statement 1006
Warning |
A readily accessible two-poled disconnect device must be incorporated in the fixed wiring. Statement 1022 |
|
|
|
|
Warning |
This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of |
|
|
|
a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if |
|
|
you are uncertain that suitable grounding is available. Statement 1024 |
|
|
|
This warning applies to only the Cisco ME 3400E-24TS-M and the Cisco ME 3400EG-12CS-M switches:
Warning |
Only trained and qualified personnel should be allowed to install, replace, or service this equipment. |
|
|
|
Statement 1030 |
|
|
|
|
|
|
Warning |
This product requires short-circuit (overcurrent) protection, to be provided as part of the building installation. |
|
|
|
Install only in accordance with national and local wiring regulations. Statement 1045 |
|
|
|
|
|
|
Warning |
To prevent the system from overheating, do not operate it in an area that exceeds the maximum recommended |
|
|
|
ambient temperature of: 122°F (50°C) Statement 1047 |
|
|
|
|
|
|
Warning |
Installation of the equipment must comply with local and national electrical codes. Statement 1074 |
|
|
|
|
When you set up the switch to enter the initial IP information, the switch can then connect to local routers and the Internet. For further configuration, access the switch CLI.
Your switch might look different from the illustrations, but the instructions apply to all the Cisco ME switches. Some instructions depend on whether the switch uses AC or DC power.
5