Cisco Systems IE200016TCB, IE20004TSB, IE20004TSL User Manual

0 (0)

Cisco IE 2000 Switch Hardware

Installation Guide

June 2013

Americas Headquarters

Cisco Systems, Inc. 170 West Tasman Drive

San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000

800 553-NETS (6387) Fax: 408 527-0883

Text Part Number: OL-25818-04

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.

Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.

You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:

Turn the television or radio antenna until the interference stops.

Move the equipment to one side or the other of the television or radio.

Move the equipment farther away from the television or radio.

Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses.)

Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

Cisco IE 2000 Switch Hardware Installation Guide

© 2012, 2013 Cisco Systems, Inc. All rights reserved.

C O N T E N T S

 

Preface vii

 

 

 

Audience

vii

 

 

Purpose vii

 

 

Conventions

vii

 

 

Related Publications viii

 

Obtaining Documentation, Obtaining Support, and Security Guidelines viii

 

Product Overview

 

C H A P T E R 1

1-1

 

Switch Models

1-2

 

Front Panel

1-5

 

 

10/100BASE-T Downlink Ports

1-8

 

 

 

 

 

 

Power over Ethernet Ports 1-9

 

 

 

 

 

10/100BASE-T Uplink Ports

1-9

 

 

 

 

 

 

10/100/1000BASE-T Uplink Ports

1-9

 

 

 

 

 

100 Mb/s SFP Module Uplink Slots

1-9

 

 

 

 

 

100/1000 Mb/s SFP Module Uplink Slots

1-9

 

 

 

 

Dual-Purpose Fast Ethernet Uplink Ports

1-9

 

 

 

 

Dual-Purpose Gigabit Ethernet Uplink Ports

1-10

 

 

 

 

Power Connectors

 

1-11

 

 

 

 

 

 

 

 

PoE Power Connector

1-12

 

 

 

 

 

 

Alarm Connector

 

1-12

 

 

 

 

 

 

 

 

Management Ports

 

1-13

 

 

 

 

 

 

 

 

LEDs

1-14

 

 

 

 

 

 

 

 

 

 

Express Setup LED

1-15

 

 

 

 

 

 

 

System LED

1-15

 

 

 

 

 

 

 

 

USB-Mini Console LED

1-15

 

 

 

 

 

 

Alarm LEDs

1-16

 

 

 

 

 

 

 

 

Power Status LEDs

1-16

 

 

 

 

 

 

 

Port Status LEDs 1-17

 

 

 

 

 

 

 

Dual-Purpose Port LEDs

1-18

 

 

 

 

 

 

PoE Status LED

1-19

 

 

 

 

 

 

 

Flash Memory Card

1-19

 

 

 

 

 

 

 

 

Rear Panel

1-21

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cisco IE 2000 Switch Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OL-25818-04

 

 

 

 

 

 

 

 

iii

 

 

 

 

 

 

 

 

 

 

 

Contents

 

Management Options

1-21

 

 

 

 

 

 

 

Network Configurations

 

1-22

 

 

 

 

 

 

 

Switch Installation

 

 

 

 

 

 

 

 

 

C H A P T E R 2

2-1

 

 

 

 

 

 

 

 

 

Preparing for Installation

2-1

 

 

 

 

 

 

 

Warnings

2-1

 

 

 

 

 

 

 

 

 

Additional Information for Installation in a Hazardous Environment

2-3

 

Hazardous Area Installation Warnings

2-3

 

 

 

 

North American Hazardous Location Approval

2-5

 

 

 

EMC Environmental Conditions for Products Installed in the European Union 2-5

 

Installation Guidelines 2-5

 

 

 

 

 

 

Environment and Enclosure Guidelines

2-5

 

 

 

 

General Guidelines

2-6

 

 

 

 

 

 

Verifying Package Contents 2-7

 

 

 

 

 

 

Installing or Removing the Flash Memory Card (Optional)

2-7

 

 

 

Connecting to a Console Port

2-9

 

 

 

 

 

 

RJ-45 Console Port

 

2-10

 

 

 

 

 

 

 

USB Mini-Type B Console Port

2-11

 

 

 

 

 

Connecting to Power

2-13

 

 

 

 

 

 

 

Tools and Equipment

2-13

 

 

 

 

 

 

Supported Power Supplies

2-13

 

 

 

 

 

 

Installing the Power Converter on a DIN Rail, Wall, or Rack Adapter

2-14

 

Grounding the Switch

2-14

 

 

 

 

 

 

Connecting the Power Converter to an AC Power Source

2-17

 

 

Preparing the AC Power Connection

2-17

 

 

 

 

Connecting the AC Power Source to the Power Converter 2-18

 

 

Connecting the Power Converter to a DC Power Source

2-19

 

 

Wiring the DC Power Source

2-20

 

 

 

 

 

Attaching the Power Connectors to the Switch

2-25

 

 

 

Connecting Power to the Switch PoE DC-Input (Optional)

2-28

 

 

Applying Power to the Power Converter 2-30

 

 

 

 

Running Boot Fast

2-30

 

 

 

 

 

 

Powering On the Switch 2-30

 

Verifying Boot Fast

2-31

 

Disconnecting Power

2-31

 

Installing the Switch 2-31

 

 

Installing the Switch on a DIN Rail

2-32

Removing the Switch from a DIN Rail

2-33

 

 

 

Connecting Alarm Circuits

2-34

 

 

 

 

Cisco IE 2000 Switch Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

iv

 

 

OL-25818-04

 

 

 

 

 

Contents

 

Wiring the Protective Ground and DC Power for Alarm Circuits 2-34

 

Wiring the External Alarms

2-35

 

 

Attaching the Alarm Connector to the Switch

2-38

 

Connecting Destination Ports

2-39

 

 

Connecting to 10/100 and 10/100/1000 Ports 2-40

 

 

Installing and Removing SFP Modules 2-42

 

 

Installing SFP Modules into SFP Module Slots

2-42

 

Removing SFP Modules from SFP Module Slots

2-43

 

Connecting to SFP Modules

2-44

 

 

Connecting to a Dual-Purpose Port 2-46

 

 

Verifying Switch Operation 2-47

 

 

Where to Go Next

2-47

 

 

 

Troubleshooting 3-1

 

 

 

 

C H A P T E R 3

 

 

 

 

 

Diagnosing Problems

3-1

 

 

 

Switch Boot Fast

3-1

 

 

 

Switch LEDs

3-2

 

 

 

 

 

Switch Connections

3-2

 

 

 

 

 

 

 

 

Bad or Damaged Cable

3-2

 

 

 

 

 

 

 

Ethernet and Fiber-Optic Cables

3-2

 

 

 

 

 

 

Link Status 3-2

 

 

 

 

 

 

 

 

 

10/100 and 10/100/1000 Port Connections

3-3

 

 

 

 

 

SFP Module

3-3

 

 

 

 

 

 

 

 

 

Interface Settings

3-3

 

 

 

 

 

 

 

 

Ping End Device

3-3

 

 

 

 

 

 

 

 

Spanning Tree Loops 3-3

 

 

 

 

 

 

 

Switch Performance

3-4

 

 

 

 

 

 

 

 

Speed, Duplex, and Autonegotiation 3-4

 

 

 

 

 

 

Autonegotiation and Network Interface Cards

3-4

 

 

 

 

 

Cabling Distance

3-4

 

 

 

 

 

 

 

 

Resetting the Switch

3-5

 

 

 

 

 

 

 

 

 

How to Recover Passwords

3-5

 

 

 

 

 

 

 

 

Finding the Switch Serial Number

3-6

 

 

 

 

 

 

Technical Specifications

 

 

 

 

 

 

 

A P P E N D I X A

A-1

 

 

 

 

 

 

 

 

Operating Temperature Specifications

A-1

 

 

 

 

 

 

Technical Specifications

A-2

 

 

 

 

 

 

 

 

Alarm Ratings A-6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cisco IE 2000 Switch Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OL-25818-04

 

 

 

 

 

 

 

v

 

 

 

 

 

 

 

 

 

 

Contents

 

 

Hazardous Locations Standards

A-6

 

 

 

 

 

 

Cable and Connectors

 

 

 

 

 

 

 

 

A P P E N D I X

B

B-1

 

 

 

 

 

 

 

 

 

Connector Specifications

B-1

 

 

 

 

 

 

 

 

10/100 Ports

B-1

 

 

 

 

 

 

 

 

 

SFP Module Connectors

B-2

 

 

 

 

 

 

 

Dual-Purpose Ports

B-2

 

 

 

 

 

 

 

 

Console Port

B-2

 

 

 

 

 

 

 

 

 

Alarm Port

B-3

 

 

 

 

 

 

 

 

 

 

Cables and Adapters

B-4

 

 

 

 

 

 

 

 

SFP Module Cables

B-4

 

 

 

 

 

 

 

 

Cable Pinouts

B-7

 

 

 

 

 

 

 

 

 

Console Port Adapter Pinouts

B-8

 

 

 

 

 

 

Configuring the Switch with the CLI-Based Setup Program

 

 

A P P E N D I X

C

C-1

 

 

 

Accessing the CLI Through the Console Port

C-1

 

 

 

 

 

Removing the USB Mini-Type B Console Port Cover C-1

 

 

 

 

RJ-45 Console Port

C-2

 

 

 

 

 

 

 

 

USB Mini-Type B Console Port

C-4

 

 

 

 

 

 

Installing the Cisco Microsoft Windows USB Device Driver

C-5

 

 

 

Installing the Cisco Microsoft Windows XP USB Driver

C-5

 

 

 

Installing the Cisco Microsoft Windows 2000 USB Driver

C-6

 

 

 

Installing the Cisco Microsoft Windows Vista and Windows 7 USB Driver

C-6

 

 

Uninstalling the Cisco Microsoft Windows USB Driver

C-7

 

 

 

 

Uninstalling the Cisco Microsoft Windows XP and 2000 USB Driver C-7

 

 

 

Uninstalling the Cisco Microsoft Windows Vista and Windows 7 USB Driver

C-7

 

 

Entering the Initial Configuration Information

C-8

 

 

 

 

 

IP Settings

C-8

 

 

 

 

 

 

 

 

 

 

Completing the Setup Program

C-8

 

 

 

 

Cisco IE 2000 Switch Hardware Installation Guide

 

vi

OL-25818-04

 

 

 

Preface

Audience

This guide is for the networking or computer technician responsible for installing Cisco IE 2000 series switches. We assume that you are familiar with the concepts and terminology of Ethernet and local area networking.

Purpose

This guide documents the hardware features of the Cisco IE 2000 switches. It describes the physical and performance characteristics of each switch, explains how to install a switch, and provides troubleshooting information.

This guide does not describe system messages that you might receive or how to configure your switch. For more information, see the Cisco IE2000 documentation at http://www.cisco.com/en/US/products/ps12451/tsd_products_support_series_home.html

For information about the standard Cisco IOS commands, see

http://www.cisco.com/cisco/web/psa/configure.html?mode=prod&level0=268438303

Conventions

This document uses the following conventions and symbols for notes, cautions, and warnings.

Note Means reader take note. Notes contain helpful suggestions or references to materials not contained in this manual.

Caution Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data.

Cisco IE 2000 Switch Hardware Installation Guide

 

OL-25818-04

vii

 

Chapter

Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device.

Statement 1071

The safety warnings for this product are translated into several languages in the Regulatory Compliance and Safety Information for the Cisco IE 2000 Switch that ships with the product. The EMC regulatory statements are also included in that guide.

Related Publications

Before installing, configuring, or upgrading the switch, see the release notes on Cisco.com for the latest information.

These documents provide complete information about the switch and are available on Cisco.com:

Cisco IE 2000 Switch Getting Started Guide

Regulatory Compliance and Safety Information for the Cisco IE 2000 Switch

Release Notes for the Cisco IE 2000 Switch

Cisco IE 2000 Switch Software Configuration Guide

Cisco IE 2000 Switch Command Reference

Cisco IE 2000 Switch System Message Guide

Device Manager online help (available on the switch)

Cisco Small Form-Factor Pluggable Modules Installation Notes

These compatibility matrix documents are available from this Cisco.com site:

http://www.cisco.com/en/US/products/hw/modules/ps5455/products_device_support_tables_list.html

Cisco Gigabit Ethernet Transceiver Modules Compatibility Matrix (not orderable but available on Cisco.com)

Cisco Small Form-Factor Pluggable Modules Compatibility Matrix (not orderable but available on Cisco.com)

Obtaining Documentation, Obtaining Support, and Security

Guidelines

For information on obtaining documentation, obtaining support, providing documentation feedback, security guidelines, and also recommended aliases and general Cisco documents, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Cisco IE 2000 Switch Hardware Installation Guide

 

viii

OL-25818-04

 

 

 

C H A P T E R 1

Product Overview

This switch provides a rugged and secure switching infrastructure for harsh environments. It is suitable for industrial Ethernet applications, including factory automation, intelligent transportation systems (ITSs), substations, oil and gas installations, and other deployments in harsh environments.

You can connect this switch to office networking devices such as Cisco IP phones, Cisco Wireless Access Points workstations, and other devices such as servers, routers, and other switches. In industrial environments, you can connect any Ethernet-enabled industrial communication devices, including programmable logic controllers (PLCs), human-machine interfaces (HMIs), drives, sensors, video devices, traffic signal controllers, and intelligent electronic devices (IEDs).

You can mount the switch on a DIN rail in an industrial enclosure. Its components are designed to withstand extremes in temperature, vibration, and shock that are common in an industrial environment.

The chapter includes the following topics:

Switch Models, page 1-2

Front Panel, page 1-5

Rear Panel, page 1-21

Management Options, page 1-21

Network Configurations, page 1-22

Cisco IE 2000 Switch Hardware Installation Guide

 

OL-25818-04

1-1

 

 

 

Chapter 1 Product Overview

Switch Models

Switch Models

Table 1-1 lists and describes the switch models.

Table 1-1

Switch Descriptions

 

 

 

 

 

Model

 

Description

Software Image

 

 

 

 

Cisco IE-2000-4T-L

4

10/100BASE-T downlink ports

LAN Lite

 

 

2

10/100BASE-T uplink ports

 

 

 

 

 

Cisco IE-2000-4T-B

4

10/100BASE-T downlink ports

LAN Base

 

 

2

10/100BASE-T uplink ports

 

 

 

 

 

Cisco IE-2000-4T-G-L

4

10/100BASE-T downlink ports

LAN Lite

 

 

2

10/100/1000BASE-T uplink ports

 

 

 

 

 

Cisco IE-2000-4T-G-B

4

10/100BASE-T downlink ports

LAN Base

 

 

2

10/100/1000BASE-T uplink ports

 

 

 

 

 

Cisco IE-2000-4TS-L

4

10/100BASE-T downlink ports

LAN Lite

 

 

2

100 Mb/s SFP (small form-factor pluggable)

 

 

 

module uplink slots

 

 

 

 

 

Cisco IE-2000-4TS-B

4

10/100BASE-T Ethernet ports

LAN Base

 

 

2

100 Mb/s SFP module uplink slots

 

 

 

 

 

Cisco IE-2000-4TS-G-L

4

10/100BASE-T downlink ports

LAN Lite

 

 

2

100/1000 Mb/s SFP module uplink slots

 

 

 

 

 

Cisco IE-2000-4TS-G-B

4

10/100BASE-T downlink ports

LAN Base

 

 

2

100/1000 Mb/s SFP module uplink slots

 

 

 

 

 

Cisco IE-2000-8TC-L

8

10/100BASE-T downlink ports

LAN Lite

 

 

2

Fast Ethernet dual-purpose uplink ports

 

 

 

 

 

Cisco IE-2000-8TC-B

8

10/100BASE-T downlink ports

LAN Base

 

 

2

Fast Ethernet dual-purpose uplink ports

 

 

 

 

 

Cisco IE-2000-8TC-G-L

8

10/100BASE-T downlink ports

LAN Lite

 

 

2

Gigabit Ethernet dual-purpose uplink ports

 

 

 

 

 

Cisco IE-2000-8TC-G-B

8

10/100BASE-T downlink ports

LAN Base

 

 

2

Gigabit Ethernet dual-purpose uplink ports

 

 

 

 

 

Cisco IE-2000-8TC-G-E

8

10/100BASE-T downlink ports

LAN Base with

 

 

2

Gigabit Ethernet dual-purpose uplink ports

1588

 

 

Supports the IEEE-1588 standard for

 

 

 

synchronizing clocks. Can enable NAT by license

 

 

 

upgrade.

 

 

 

 

 

Cisco IE-2000-8TC-G-N

8

10/100BASE-T downlink ports

LAN Base with

 

 

2

Gigabit Ethernet dual-purpose uplink ports

1588 and NAT

 

 

Supports the IEEE-1588 standard for

 

 

 

synchronizing clocks and Network Address

 

 

 

Translation (NAT)

 

 

 

 

 

 

Cisco IE 2000 Switch Hardware Installation Guide

1-2

OL-25818-04

 

 

Chapter 1 Product Overview

Switch Models

Table 1-1

Switch Descriptions (continued)

 

 

 

 

 

Model

 

Description

Software Image

 

 

 

Cisco IE-2000-16TC-L

16 10/100BASE-T downlink ports,

LAN Lite

 

 

2

Fast Ethernet dual-purpose uplink ports

 

 

 

2

100 Mb/s SFP module uplink slots

 

 

 

 

Cisco IE-2000-16TC-B

16 10/100BASE-T downlink ports

LAN Base

 

 

2

Fast Ethernet dual-purpose uplink ports

 

 

 

2

100 Mb/s SFP module uplink slots

 

 

 

 

Cisco IE-2000-16TC-G-L

16 10/100BASE-T downlink ports

LAN Lite

 

 

2

Gigabit Ethernet dual-purpose uplink ports

 

 

 

2

100 Mb/s SFP module uplink slots

 

 

 

 

Cisco IE-2000-16TC-G-E

16 10/100BASE-T downlink ports

LAN Base with

 

 

2

Gigabit Ethernet dual-purpose uplink ports

1588

 

 

 

 

 

2

100 Mb/s SFP module uplink slots

 

 

 

Supports the IEEE-1588 standard for

 

 

 

synchronizing clocks. Can enable NAT by license

 

 

 

upgrade.

 

 

 

 

Cisco IE-2000-16TC-G-N

16 10/100BASE-T downlink ports

LAN Base with

 

 

2

Gigabit Ethernet dual-purpose uplink ports

1588 and NAT

 

 

 

 

 

Supports the IEEE-1588 standard for

 

 

 

synchronizing clocks and Network Address

 

 

 

Translation (NAT).

 

 

 

 

Cisco IE-2000-16TC-G-X

16 10/100BASE-T downlink ports

LAN Base with

 

 

2

Gigabit Ethernet uplink ports, and 2 100 Mb/s

1588 and

 

 

conformal coat

 

 

SFP module uplink slots

 

 

 

 

 

Supports the IEEE-1588 standard for

 

 

 

synchronizing clocks.

 

 

 

Can enable NAT by license upgrade.

 

 

 

 

Cisco IE-2000-16PTC-G-E

12 10/100BASE-T downlink ports

LAN Base with

 

 

2

Gigabit Ethernet dual-purpose uplink ports

1588

 

 

 

 

 

4

Power over Ethernet (PoE) ports

 

 

 

Note The four PoE ports can operate as PoE or

 

 

 

 

as PoE+ if sufficient external power

 

 

 

 

source is provided.

 

 

 

Supports the IEEE-1588 standard for

 

 

 

synchronizing clocks.

 

 

 

Can enable NAT by license upgrade.

 

 

 

 

 

 

Cisco IE 2000 Switch Hardware Installation Guide

 

OL-25818-04

1-3

 

 

 

Chapter 1 Product Overview

Switch Models

Table 1-1

Switch Descriptions (continued)

 

 

 

 

 

Model

 

Description

Software Image

 

 

 

Cisco IE-2000-16PTC-G-L

12 10/100BASE-T downlink ports

LAN Lite

 

 

2

Gigabit Ethernet dual-purpose uplink ports

 

 

 

4

Power over Ethernet (PoE) ports

 

 

 

Note The four PoE ports can operate as PoE or

 

 

 

 

as PoE+ if sufficient external power

 

 

 

 

source is provided.

 

 

 

 

Cisco IE-2000-16PTC-G-NX

12 10/100BASE-T downlink ports

LAN Base with

 

 

2

Gigabit Ethernet dual-purpose uplink ports

1588 and

 

 

conformal coat

 

 

4

Power over Ethernet (PoE) ports

 

 

 

 

 

Note The four PoE ports can operate as PoE or

 

 

 

 

as PoE+ if sufficient external power

 

 

 

 

source is provided.

 

 

 

Note Supports the IEEE-1588 standard for

 

 

 

 

synchronizing clocks and Network

 

 

 

 

Address Translation (NAT).

 

 

 

 

 

 

Cisco IE 2000 Switch Hardware Installation Guide

1-4

OL-25818-04

 

 

Chapter 1 Product Overview

Front Panel

Front Panel

This section describes the front panel components. See Table 1-1.

10/100BASE-T Ethernet ports

10/100/1000 uplink ports (available on some models).

Dual-purpose ports (available on some models).

SFP module slots (available on some models).

PoE/PoE+ ports (available on some models). See Power over Ethernet Ports, page 1-9.

RJ-45 console port

USB mini-Type B (console) port

LEDs

Power connectors

Alarm connector

Flash memory card slot

The following figures depict the components available on the various models in this product family. Not all models are illustrated.

Figure 1-1 Cisco IE-2000-4TS-L Front Panel View

3

1

±12/24/485- .

0.

0A

2

4TS

9

4

5

6

7

8

331547

 

1

10/100 Ethernet ports (downlink ports)

6

Power connector DC-B

 

 

 

 

 

 

 

2

SFP module slots (uplink ports)

7

Alarm connector

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cisco IE 2000 Switch Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OL-25818-04

 

 

 

 

1-5

 

 

 

 

 

 

 

Chapter 1 Product Overview

Front Panel

3

USB mini-Type B (console) port

8

Protective ground connection

 

 

 

 

4

RJ-45 console port

9

Flash memory card slot

 

 

 

 

5

Power connector DC-A

 

 

 

 

 

 

 

Figure 1-2

Cisco IE-2000-8TC-L Front Panel

 

3

1

2

8TC

331545

4

5

6

7

8

9

1

10/100 Ethernet ports (downlink ports)

6

Power connector DC-B

 

 

 

 

2

Dual-purpose ports (uplink ports)

7

Alarm connector

 

 

 

 

3

USB mini-Type B (console) port

8

Protective ground connection

 

 

 

 

4

RJ-45 console port

9

Flash memory card slot

 

 

 

 

5

Power connector DC-A

 

 

 

 

 

 

Cisco IE 2000 Switch Hardware Installation Guide

1-6

OL-25818-04

 

 

Chapter 1 Product Overview

Front Panel

Figure 1-3

Cisco IE-2000-16TC-L Front Panel View

 

331544

 

3

1

4

 

 

5

 

0.5±12/24/48-

 

3.0A

10

6

16TC

7

 

 

8

 

2

 

9

1

10/100 Ethernet ports (downlink ports)

6

Power connector DC-B

 

 

 

 

2

Dual-purpose ports (uplink ports)

7

Alarm connector

 

 

 

 

3

USB mini-Type B (console) port

8

Protective ground connection

 

 

 

 

4

RJ-45 console port

9

Flash memory card slot

 

 

 

 

5

Power connector DC-A

10

SFP module slots

 

 

 

 

Cisco IE 2000 Switch Hardware Installation Guide

 

OL-25818-04

1-7

 

 

 

Chapter 1 Product Overview

Front Panel

Figure 1-4 Cisco IE-2000-16PTC-G-E Switch Front Panel View

1

10

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

5

 

 

 

 

 

±12/24/

 

 

 

 

 

5

-3.

48

 

 

ST

 

 

0.

PoE

 

 

 

0A

ATUS

 

 

 

 

 

 

 

 

 

 

PoE DC IN -

 

 

 

 

6

DC

IN +

 

 

 

 

 

-G

 

 

 

 

 

 

 

 

 

 

 

7

16PTC

 

 

I

DC

 

 

 

 

 

54V

,12

 

 

 

 

 

 

nput

A

 

 

 

 

 

 

 

 

 

8

 

 

 

 

 

2

 

347587

 

 

 

 

 

9

 

1

10/100 Ethernet ports (downlink ports)

6

Power connector DC-B

 

 

 

 

2

Dual-purpose ports (uplink ports)

7

Alarm connector

 

 

 

 

3

USB mini-Type B (console) port

8

Protective ground connection

 

 

 

 

4

RJ-45 console port

9

Flash memory card slot

 

 

 

 

5

Power connector DC-A

10

PoE power connector

 

 

 

 

10/100BASE-T Downlink Ports

You can set the 10/100BASE-T downlink ports to operate at 10 or 100 Mb/s in full-duplex or half-duplex mode. You can also set these ports for speed and duplex autonegotiation in compliance with

IEEE 802.3AB. (The default setting is autonegotiate.) When set for autonegotiation, the port senses the speed and duplex settings of the attached device and advertises its own capabilities. If the connected device also supports autonegotiation, the switch port negotiates the best connection (that is, the fastest line speed that both devices support, and full-duplex transmission if the attached device supports it) and configures itself accordingly. In all cases, the attached device must be within 328 feet (100 meters). 100BASE-TX traffic requires Category 5 cable. 10BASE-T traffic can use Category 3 or Category 4 cables.

When connecting the switch to workstations, servers, routers, and Cisco IP phones, make sure that the cable is a straight-through cable.

Cisco IE 2000 Switch Hardware Installation Guide

1-8

OL-25818-04

 

 

Chapter 1 Product Overview

Front Panel

You can use the mdix auto interface configuration command in the command-line interface (CLI) to enable the automatic medium-dependent interface crossover (auto-MDIX) feature. When the autoMDIX feature is enabled, the switch detects the required cable type for copper Ethernet connections and configures the interfaces accordingly. For configuration information for this feature, see the switch software configuration guide or the switch command reference.

Power over Ethernet Ports

On certain models of the IE 2000 switch, four of the 10/100BASE-T ports are available as PoE ports. The four ports can operate as PoE (IEEE 802.3af) ports or can be configured to operate as PoE+

(IE 802.at) ports. Each PoE port requires 15.4 Watts of power while PoE+ requires 30 Watts. A 54VDC /1.2Amp power source (65W) can support 4 PoE ports or 2 PoE+ ports.

Cable lengths of up to 328 ft (100 m) are supported.

10/100BASE-T Uplink Ports

The IEEE 802.3u 10/100BASE-T uplink ports provide full-duplex 10, 100 Mb/s connectivity over Category 5 unshielded twisted pair (UTP) copper cabling. The default setting is autonegotiate. The cable can be up to 100 m (0.1 km) in length.

10/100/1000BASE-T Uplink Ports

The IEEE 802.3u 10/100/1000BASE-T uplink ports provide full-duplex 10, 100 or 1000 Mb/s connectivity over Category 5 unshielded twisted pair (UTP) copper cabling. The default setting is autonegotiate. The cable can be up to 100 m (0.1 km) in length.

100 Mb/s SFP Module Uplink Slots

The IEEE 802.3u 100 Mb/s SFP module uplink slots provide full-duplex 100 Mb/s connectivity over multi-mode (MM) fiber cables or single-mode (SM) fiber cables. These ports use a SFP fiber-optic transceiver module that accepts a dual LC connector. Check the SFP specifications for the cable type and length.

100/1000 Mb/s SFP Module Uplink Slots

The IEEE 802.3u 100 Mb/s SFP module uplink slots provide full-duplex 100 or 1000 Mb/s connectivity over multi-mode (MM) fiber cables or single-mode (SM) fiber cables. These ports use a SFP fiber-optic transceiver module that accepts a dual LC connector. Check the SFP specifications for the cable type and length.

Dual-Purpose Fast Ethernet Uplink Ports

You can configure the dual-purpose Fast Ethernet uplink ports on the switch as either 10/100BASE-T ports or as 100 Mb/s SFP-module ports. You can set the 10/100 ports to autonegotiate, or you can configure them as fixed 10 or 100 Mb/s ports.

Cisco IE 2000 Switch Hardware Installation Guide

 

OL-25818-04

1-9

 

 

 

Chapter 1 Product Overview

Front Panel

By default, the switch selects the medium for each dual-purpose port (10/100BASE-T or SFP). When a link is achieved on one media type, the switch disables the other media type until the active link goes down. If links are active on both media, the SFP-module port has priority, but you can use the mediatype interface configuration command to manually designate the port as an RJ-45 port or an SFP port.

You can configure the speed and duplex settings consistent with the selected media type. For information on configuring interfaces, see the switch software configuration guide.

Dual-Purpose Gigabit Ethernet Uplink Ports

You can configure the dual-purpose Gigabit Ethernet uplink ports on the switch as either 10/1001000BASE-T ports or as 100/1000 Mb/s SFP-module ports. You can set the 10/100/1000BASE- T ports to autonegotiate, or you can configure them as fixed 10, 100, or 1000 Mb/s (Gigabit) Ethernet ports.

By default, the switch selects the medium for each dual-purpose port (10/100/1000BASE-T or SFP). When a link is achieved on one media type, the switch disables the other media type until the active link goes down. If links are active on both media, the SFP-module port has priority, but you can use the media-type interface configuration command to manually designate the port as an RJ-45 port or an SFP port.

You can configure the speed and duplex settings consistent with the selected media type. For information on configuring interfaces, see the switch software configuration guide.

SFP Modules

The SFP modules are switch Ethernet SFP modules that provide connections to other devices. These field-replaceable transceiver modules provide the uplink interfaces. The modules have LC connectors for fiber-optic connections.

Note The Cisco IE 2000 switch does not support copper SFP modules.

You can use any combination of the supported SFP modules:

Table 1-2 Supported SFP Models

Type of SFP Module

Model

 

 

Rugged and Industrial SFPs

GLC-SX-MM-RGD with digital optical monitoring (DOM)

–40 to 185°F (–40 to 85°C)

support

 

 

GLC-LX-SM-RGD with DOM support

 

GLC-ZX-SM-RGD with DOM support

 

 

 

Cisco IE 2000 Switch Hardware Installation Guide

1-10

OL-25818-04

Chapter 1 Product Overview

Front Panel

Table 1-2 Supported SFP Models

Type of SFP Module

Model

 

 

Commercial SFPs

GLC-SX-MM

32 to 158°F (0 to 70°C)

GLC-LH-SM

 

GLC-BX-U with DOM support

 

GLC-BX-D with DOM support

 

CWDM-SFP with DOM support

 

DWDM-SFP with DOM support

 

 

Extended temperature SFPs

SFP-GE-S with DOM support

23 to 185°F (–5 to 85°C)

SFP-GE-L with DOM support

 

SFP-GE-Z with DOM support

 

GLC-SX-SMD

 

GLC-LH-SMD

 

GLC-EX-SMD

 

 

For the most up-to-date list of supported SFP models for Cisco Industrial Ethernet switches, see http://www.cisco.com/en/US/docs/interfaces_modules/transceiver_modules/compatibility/matrix/OL_ 6981.html#wp138176

For installation instructions, see your SFP module documentation and the “Installing and Removing SFP Modules” section on page 2-42.

For cable specifications, see the “SFP Module Cables” section on page B-4.

Power Connectors

You connect the DC power to the switch through the front panel connectors. The switch has a dual-feed DC power supply; two connectors provide primary and secondary DC power (DC-A and DC-B). The DC power connectors are near the top right of the front panel. See Figure 1-1. Each power connector has an LED status indicator.

The switch power connectors are attached to the switch chassis. Each power connector has screw terminals for terminating the DC power (see Figure 1-5). All connectors are attached to the switch front panel with the provided captive screws.

The power connector labeling is on the panel. The positive DC power connection is labeled “+”, and the return connection is labeled “–”.

 

 

Cisco IE 2000 Switch Hardware Installation Guide

 

 

 

 

 

 

OL-25818-04

 

 

1-11

 

 

 

 

 

Chapter 1 Product Overview

Front Panel

Figure 1-5 Power Connector

331209

The switch can operate with a single power source or with dual power sources. When both power sources are operational, the switch draws power from the DC source with the higher voltage. If one of the two power sources fail, the other continues to power the switch.

PoE Power Connector

The IE 2000 switch models with PoE capability (IE-2000-16PTC-G-E, IE-2000-16PTC-G-L, and IE- 2000-16PTC-G-NX) are equipped with an additional DC input terminal block. This DC terminal block allows the connection of a second power supply (see the “Power over Ethernet Ports” section on page 1- 9), or a second input from site source DC power to operate the PoE ports. The PoE terminal block accepts 48 VDC or 54 VDC at 2.5 A.

Alarm Connector

You connect the alarm signals to the switch through the alarm connector. The switch supports two alarm inputs and one alarm output relay. The alarm connector is on the bottom right of the front panel. See Figure 1-2.

The alarm connector provides six alarm wire connections. The connector is attached to the switch front panel with the provided captive screws.

Figure 1-6 Alarm Connector

331208

Both alarm input circuits can sense if the alarm input is open or closed. The alarm inputs can be activated for environmental, power supply, and port status alarm conditions. From the CLI, you can configure each alarm input as an open or closed contact.

The alarm output circuit is a relay with a normally open and a normally closed contact. The switch is configured to detect faults that are used to energize the relay coil and change the state on both of the relay contacts: normally open contacts close, and normally closed contacts open. The alarm output relay can be used to control an external alarm device, such as a bell or a light.

See the switch software configuration guide for instructions on configuring the alarm relays.

For more information about the alarm connector, see Appendix B, “Cable and Connectors.”

 

Cisco IE 2000 Switch Hardware Installation Guide

1-12

OL-25818-04

Chapter 1 Product Overview

Front Panel

Management Ports

You can connect the switch to a PC running Microsoft Windows or to a terminal server through either the RJ-45 console port or the USB mini-Type B console port, also referred to as the USB-mini console port. These ports use the following connectors:

RJ-45 console port uses an RJ-45-to-DB-9 female cable.

USB-mini console port (5-pin connector) uses a USB Type A-to-5-pin mini-Type B cable. The USB-mini console interface speeds are the same as the RJ-45 console interface speeds.

To use the USB-mini console port, you must install the Cisco Windows USB device driver on the device that is connected to the USB-mini console port and that is running Microsoft Windows.

Note For information about downloading the Cisco USB device driver, see the “Installing the Cisco Microsoft Windows USB Device Driver” section on page C-5.

With the Cisco Windows USB device driver, connecting and disconnecting the USB cable from the console port does not affect Windows HyperTerminal operations. Mac OS X or Linux require no special drivers.

Note The 5-pin mini-Type B connectors resemble the 4-pin mini-Type B connectors, but they are not compatible. Use only the 5-pin mini-Type B. See Figure 1-7.

Figure 1-7 USB Mini-Type B Port

253163

The configurable inactivity timeout reactivates the RJ-45 console port if the USB-mini console port is activated, but no input activity occurs for a specified time period. When the USB-mini console port deactivates due to a timeout, you can restore its operation by disconnecting and reconnecting the USB cable. For information on using the CLI to configure the USB-mini console interface, see the switch software guide.

 

 

Cisco IE 2000 Switch Hardware Installation Guide

 

 

 

 

 

 

OL-25818-04

 

 

1-13

 

 

 

 

 

Cisco Systems IE200016TCB, IE20004TSB, IE20004TSL User Manual

Chapter 1 Product Overview

Front Panel

LEDs

You can use the LEDs to monitor the switch status, activity, and performance. Figure 1-8 and Figure 1- 9 show the front panel LEDs.

Figure 1-8 LEDs on the Cisco IE 2000 Switch

2

3

4

 

 

5

7

±12/24/48

±12/24/48

0A

0.5-3.0A

16TC

1

8

6

9

331565

1

Alarm LEDs

6

Power connector DC-B LED

2

USB mini-Type B (console) port LED

7

10/100BASE-T downlink port LEDs

3

Express Setup LED

8

SFP module slot LEDs

4

System LED

9

Dual-purpose uplink port LEDs

5

Power connector DC-A LED

 

 

Note On IE 2000 switches with PoE support, the two SFP ports and the associated LEDs are replaced by a PoE DC-input terminal block and a PoE LED. See Table 1-10 for the PoE LED colors and meanings.

 

Cisco IE 2000 Switch Hardware Installation Guide

1-14

OL-25818-04

Chapter 1 Product Overview

Front Panel

Express Setup LED

The Express Setup LED displays the express setup mode for the initial configuration. Table 1-3 lists the LED colors and their meanings.

Table 1-3

Setup LED

 

 

 

Color

 

Setup Status

 

 

 

Off (dark)

 

Switch is configured as a managed switch.

 

 

 

Solid green

 

Switch is operating normally.

 

 

 

Blinking green

 

Switch is in initial setup, in recovery, or initial setup is

 

 

incomplete.

 

 

 

Solid red

 

Switch failed to start initial setup or recovery because

 

 

there is no available switch port to which to connect the

 

 

management station. Disconnect a device from a switch

 

 

port, and then press the Express Setup button.

 

 

 

System LED

The System LED shows whether the system is receiving power and is functioning properly.

Table 1-4 lists the system LED colors and their meanings.

Table 1-4

System LED

 

 

 

Color

 

System Status

 

 

 

Off

 

System is not powered on.

 

 

 

Blinking green

 

Boot fast is in progress.

 

 

 

Green

 

System is operating normally.

 

 

 

Red

 

Switch is not functioning properly.

 

 

 

USB-Mini Console LED

The USB-mini console LED shows which console port is in use. See Figure 1-8 for the LED location.

If you connect a cable to a console port, the switch automatically uses that port for console communication. If you connect two console cables, the USB-mini console port has priority. Table 1-5 describes the system LED colors and their meanings.

Table 1-5

USB-Mini Console Port LED

 

 

Color

Description

 

 

Green

USB-mini console port is active.

 

RJ-45 console port LED is not active.

 

 

Off

Port is not active.

 

RJ-45 console port is active.

 

 

 

 

Cisco IE 2000 Switch Hardware Installation Guide

 

 

 

 

 

 

OL-25818-04

 

 

1-15

 

 

 

 

 

Chapter 1 Product Overview

Front Panel

Alarm LEDs

Table 1-6 and Table 1-7 list the alarm LED colors and their meanings.

Table 1-6

Alarm OUT Status LED

 

 

Color

System Status

 

 

Off

Alarm OUT is not configured, or the switch is off.

 

 

Green

Alarm OUT is configured, no alarm detected.

 

 

Blinking red

Switch has detected a major alarm.

 

 

Red

Switch has detected a minor alarm.

 

 

Table 1-7

Alarm IN1 and IN2 Status LEDs

 

 

Color

System Status

 

 

Off

Alarm IN1 or IN2 not configured.

 

 

Green

Alarm IN1 or IN2 configured, no alarm detected.

 

 

Blinking red

Major alarm detected.

 

 

Red

Minor alarm detected.

 

 

Power Status LEDs

The switch can operate with one or two DC power sources. Each DC input has an associated LED that shows the status of the corresponding DC input. If power is present on the circuit, the LED is green. If power is not present, the LED color depends on the alarm configuration. If alarms are configured, the LED is red when power is not present; otherwise, the LED is off.

If the switch has dual power sources, the switch draws power from the power source with the higher voltage. If one of the DC sources fails, the alternate DC source powers the switch, and the corresponding power status LED is green. The power status for the failed DC source is either off or red, depending on the alarm configuration.

Table 1-8 lists the power status LED colors and meanings.

Table 1-8

Power Status LEDs

 

 

Color

System Status

 

 

Green

Power is present on the associated circuit, system is operating normally.

 

 

Off

Power is not present on the circuit, or the system is not powered up.

 

 

Red

Power is not present on the associated circuit, and the power supply alarm is configured.

 

 

Note The Power A and Power B LEDs show that power is not present on the switch if the power input drops below the low valid level. The power status LEDs only show that power is present if the voltage at the switch input exceeds the valid level.

For information about the power LED colors during the boot fast sequence, see the “Verifying Switch Operation” section on page 2-47.

 

Cisco IE 2000 Switch Hardware Installation Guide

1-16

OL-25818-04

Chapter 1 Product Overview

Front Panel

Port Status LEDs

Each 10/100BASE-T downlink port, 10/100BASE-T uplink port, 10/100/1000BASE-T uplink port, dual-purpose uplink port, and SFP Module uplink slot has a port status LED, also called a port LED, as shown in Figure 1-8 and Figure 1-9. Table 1-9 displays LED information about the switch and the individual ports.

Table 1-9

Port Status LEDs

 

 

 

Color

 

System Status

 

 

 

Off

 

No link.

 

 

 

Solid green

 

Link present.

 

 

 

Blinking green

 

Activity. Port is sending or receiving data.

 

 

 

Alternating

 

Link fault. Error frames can affect connectivity, and errors

green-amber

 

such as excessive collisions, CRC errors, and alignment and

 

 

jabber errors are monitored for a link-fault indication.

 

 

 

Solid amber

 

Port is not forwarding. The port was disabled by management,

 

 

an address violation, or STP.

 

 

Note After a port is reconfigured, the port LED can remain

 

 

amber for up to 30 seconds while STP checks the

 

 

switch for possible loops.

 

 

 

 

 

Cisco IE 2000 Switch Hardware Installation Guide

 

 

 

 

 

 

OL-25818-04

 

 

1-17

 

 

 

 

 

Chapter 1 Product Overview

Front Panel

Dual-Purpose Port LEDs

Figure 1-9 shows the LEDs on a dual-purpose port. You can configure each port as either a 10/100/1000BASE-T port through the RJ-45 connector or as an SFP module, but not both at the same time. The LEDs show how the port is being used (Ethernet or SFP module).

The LED colors have the same meanings as described in Table 1-9.

Figure 1-9 Dual-Purpose Port LEDs

332704

1

1 Dual-purpose port LEDs

 

Cisco IE 2000 Switch Hardware Installation Guide

1-18

OL-25818-04

Chapter 1 Product Overview

Front Panel

PoE Status LED

The PoE STATUS LED is located on the front panel of the IE 2000 switch models that are equipped with PoE ports.The LED displays the functionality and status of the PoE ports. The LED colors and meanings are listed in Table 1-10.

Table 1-10

PoE Status LED Colors and Meanings

 

 

 

 

 

Color

 

PoE Status

 

 

 

 

 

Off

 

PoE is off. If the powered device is receiving power from a non-PoE power source,

 

 

 

the port LED is off even if the powered device is connected to the switch port.

 

 

 

 

 

Green

 

PoE is on. The port LED is green only when the PoE port is providing power.

 

 

 

 

Alternating green

PoE is denied because providing power to the powered device will exceed the switch

 

and amber

 

power capacity.

 

 

 

 

 

 

Flashing amber

 

 

PoE is off due to a fault.

 

 

 

 

 

 

 

 

 

 

Caution Noncompliant cabling or powered devices can cause a PoE port fault. Use

 

 

 

 

 

 

only standard-compliant cabling to connect Cisco prestandard IP Phones

 

 

 

 

 

 

and wireless access points or IEEE 802.3af-compliant devices. You must

 

 

 

 

 

 

remove any cable or device that causes a PoE fault.

 

 

 

 

 

 

 

 

 

 

Amber

 

PoE for the port is disabled. (PoE is enabled by default.)

 

 

 

 

 

 

 

 

Flash Memory Card

The switch supports a flash memory card that makes it possible to replace a failed switch without reconfiguring the new switch. The slot for the flash memory card is on the front of the switch. See Figure 1-10.

The flash card is hot swappable and can be accessed on the front panel. A cover protects the flash card and holds the card firmly in place. The cover is hinged and closed with a captive screw. This prevents the card from coming loose and protects against shock and vibration.

Note For more information on inserting and removing the flash memory card, see the “Installing or Removing the Flash Memory Card (Optional)” section on page 2-7.

 

 

Cisco IE 2000 Switch Hardware Installation Guide

 

 

 

 

 

 

OL-25818-04

 

 

1-19

 

 

 

 

 

Chapter 1 Product Overview

Front Panel

Figure 1-10 Flash Memory Card Slot

331548

16TC

Note The replacement SD card part number is SD-IE-1GB.

 

Cisco IE 2000 Switch Hardware Installation Guide

1-20

OL-25818-04

Chapter 1 Product Overview

Rear Panel

Rear Panel

The rear panel of the switch has a latch for installation on a DIN rail. See Figure 1-11. The latch is spring-loaded to move down to position the switch over a DIN rail and return to the original position to secure the switch to a DIN rail.

Figure 1-11 Cisco IE 2000 Switch Rear Panel

1

331552

1 Latch

Management Options

The switch supports these management options:

Cisco Network Assistant

Cisco Network Assistant is a PC-based network management GUI application optimized for LANs of smalland medium-sized businesses. Using the GUI, you can configure and manage switch clusters or standalone switches. Cisco Network Assistant is available at no cost and can be downloaded from this URL:

http://www.cisco.com/en/US/products/ps5931/tsd_products_support_series_home.html

For information on starting the Cisco Network Assistant application, see the Getting Started with Cisco Network Assistant guide on Cisco.com.

Device Manager

You can use Device Manager, which is in the switch memory, to manage individual and standalone switches. This web interface offers quick configuration and monitoring. You can access Device Manager from anywhere in your network through a web browser. For more information, see the getting started guide and the Device Manager online help.

 

 

Cisco IE 2000 Switch Hardware Installation Guide

 

 

 

 

 

 

OL-25818-04

 

 

1-21

 

 

 

 

 

Chapter 1 Product Overview

Network Configurations

Cisco IOS CLI

The switch CLI is based on Cisco IOS software and is enhanced to support desktop-switching features. You can fully configure and monitor the switch. You can access the CLI either by connecting your management station directly to the switch management port, or a console port, or by using Telnet from a remote management station. See the switch command reference on Cisco.com for more information.

Cisco Prime LAN Management Solution 4.2

http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.2/device_su pport/table/lms42sdt.html#Cisco IE 2000 Series Switches

SNMP network management

You can manage switches from a SNMP-compatible management station that is running platforms such as HP OpenView or SunNet Manager. The switch supports a comprehensive set of Management Information Base (MIB) extensions and four Remote Monitoring (RMON) groups. See the switch software configuration guide on Cisco.com and the documentation that came with your SNMP application for more information.

Common Industrial Protocol

The Common Industrial Protocol (CIP) management objects are supported. The Cisco IE 2000 can be managed by CIP-based management tools, allowing the user to manage an entire industrial automation system with one tool.

PROFINET TCP/IP and RT

This switch supports PROFINET TCP/IP and RT and can be managed by Siemens' automation software such as STEP 7.

Network Configurations

See the switch software configuration guide on Cisco.com for network configuration concepts and examples of using the switch to create dedicated network segments and interconnecting the segments through Gigabit Ethernet connections.

 

Cisco IE 2000 Switch Hardware Installation Guide

1-22

OL-25818-04

Loading...
+ 80 hidden pages