Casio WK-500, WK-200 User Manual 2

0 (0)

USER’S GUIDE

Please keep all information for future reference.

Safety Precautions

Before trying to use the keyboard, be sure to read the separate “Safety Precautions”.

GUÍA DEL USUARIO

Guarde toda la información para futuras consultas.

Precauciones de seguridad

Antes de intentar usar el teclado, asegúrese de leer las “Precauciones de seguridad” separadas.

ES

English

Español

WK200/500ES1B

NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

FCC WARNING

Changes or modifications not expressly approved by the party responsible for compliance could void the userís authority to operate the equipment.

Declaration of Conformity

Model Number: WK-200/WK-500

Trade Name: CASIO COMPUTER CO., LTD. Responsible party: CASIO AMERICA, INC.

Address: 570 MT. PLEASANT AVENUE, DOVER, NEW JERSEY 07801 Telephone number: 973-361-5400

This device complies with Part 15 of the FCC Rules, Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Important!

Please note the following important information before using this product.

Before using the optional AC Adaptor to power the unit, be sure to check the AC Adaptor for any damage first. Carefully check

 

 

the power cord for breakage, cuts, exposed wire and other serious damage. Never let children use an AC adaptor that is

English

 

seriously damaged.

 

 

Never attempt to recharge batteries.

 

Do not use rechargeable batteries.

 

Never mix old batteries with new ones.

 

Use recommended batteries or equivalent types.

 

Always make sure that positive (+) and negative (–) poles are facing correctly as indicated near the battery compartment.

 

Replace batteries as soon as possible after any sign they are getting weak.

 

Do not short-circuit the battery terminals.

 

The product is not intended for children under 3 years.

 

• Use only a CASIO AD-5 (for WK-200) or AD-12 (for WK-500) adaptor.

 

The AC adaptor is not a toy.

 

Be sure to disconnect the AC adaptor before cleaning the product.

 

This mark applies in EU countries only.

Manufacturer:

CASIO COMPUTER CO.,LTD.

6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan

Responsible within the European Union:

CASIO EUROPE GmbH

Bornbarch 10, 22848 Norderstedt, Germany

Company and product names used in this manual may be registered trademarks of others.

Any reproduction of the contents of this manual, either in part or its entirety, is prohibited. Except for your own, personal use, any other use of the contents of this manual without the consent of CASIO is prohibited under copyright laws.

IN NO EVENT SHALL CASIO BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, LOSS OF INFORMATION) ARISING OUT OF THE USE OF OR INABILITY TO USE THIS MANUAL OR PRODUCT, EVEN IF CASIO HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

The contents of this manual are subject to change without notice.

E-1

Contents

General Guide .............................

E-4

Using the 10-key Pad (bs) .................................

E-6

FUNCTION Button (ct) Functions .....................

E-6

Getting Ready to Play ................

E-8

Preparing the Music Stand .................................

E-8

Power Supply .....................................................

E-8

Playing the Digital Keyboard.....

E-9

Turning on Power and Playing ...........................

E-9

Using Headphones.............................................

E-9

Changing Keyboard Response to

 

Touch Pressure (Touch Response)..................

E-10

Adjusting Display Contrast ...............................

E-10

Using the Metronome .......................................

E-11

Controlling the

 

Keyboard Sounds.....................

E-12

Select from a variety of

 

musical instrument sounds...............................

E-12

Layering Two Tones.........................................

E-13

Splitting the Keyboard between

 

Two Different Tones .........................................

E-13

Using Reverb....................................................

E-14

Using Chorus....................................................

E-14

Using a Pedal ...................................................

E-15

Changing the Pitch

 

(Transpose, Tuning, Octave Shift)....................

E-15

Using the Pitch Bend Wheel to Shift the

 

Pitch of Notes (WK-500 Only) ..........................

E-16

Sampling Sounds and

 

Playing Them on the

 

Digital Keyboard .......................

E-17

Connection and Preparation.............................

E-17

Sampling and Playing a Melody Sound

 

(Melody Sampling) ...........................................

E-18

Incorporating a Sampled Sound into a

 

Drum Set (Drum Sampling) ..............................

E-20

Other Sampling Functions................................

E-22

Playing Built-in Songs..............

E-25

Playing the Demo Songs .................................

E-25

Playing Back a Particular Song........................

E-26

Increasing the Selection of Songs ...................

E-28

Using Built-in Songs to

 

Master Keyboard Play ..............

E-29

Phrases............................................................

E-29

Step Up Lesson Flow.......................................

E-29

Selecting the Song, Phrase, and

 

Part You Want to Practice................................

E-30

Lessons 1, 2, and 3..........................................

E-31

Lesson Settings ...............................................

E-32

Using Auto Step Up Lesson.............................

E-34

Music Challenge

 

Keyboard Game ........................

E-35

Using Auto Accompaniment....

E-36

Playing the Rhythm Part Only..........................

E-36

Playing All Parts...............................................

E-37

Using Auto Accompaniment Effectively ...........

E-39

Using One-Touch Preset .................................

E-40

Using Auto Harmonize .....................................

E-41

Editing Auto Accompaniment

 

Patterns......................................

E-42

Saving Keyboard Setups to

 

Registration Memory ................

E-46

To save a setup to registration memory...........

E-47

To recall a setup from registration memory .....

E-47

Recording Your

 

Keyboard Play...........................

E-48

Recording and Playing Back Keyboard Play ...

E-48

Using Tracks to Record and Mix Parts ............

E-49

Recording Two or More Songs, and

 

Selecting One for Playback..............................

E-51

Recording while Playing Along with a

 

Built-in Song.....................................................

E-51

Saving Recorded Data on an

 

External Device................................................

E-52

E-2

 

 

 

 

 

 

 

Contents

Other Useful Digital Keyboard

 

Reference

E-70

 

Functions ..................................

E-53

Troubleshooting ...............................................

E-70

Changing the Scale of the Keyboard................

E-53

Specifications...................................................

E-72

Using Music Preset ..........................................

E-56

Operating Precautions .....................................

E-73

Using the Arpeggiator.......................................

E-56

Error Messages................................................

E-74

Deleting User Song Data..................................

E-57

Song List ..........................................................

E-75

Deleting All Data in Digital Keyboard

 

MIDI Implementation Chart

Memory ............................................................

E-58

Using a Memory Card

 

 

 

(WK-500 Only) ...........................

E-59

 

 

SD Memory Card and Card Slot

 

 

 

Precautions ......................................................

E-59

 

 

Inserting and Removing an

 

 

 

SD Memory Card..............................................

E-60

 

 

Formatting an SD Memory Card.......................

E-60

 

 

Saving Digital Keyboard Data to an

 

 

 

SD Memory Card..............................................

E-61

 

 

Loading Data from an SD Memory Card

 

 

 

into Digital Keyboard Memory ..........................

E-62

 

 

Deleting Data from an SD Memory Card..........

E-63

 

 

Playing Back Data from an

 

 

 

SD Memory Card..............................................

E-64

 

 

SD Memory Card Error Messages ...................

E-64

 

 

Connecting External

 

 

 

Devices ......................................

E-65

 

 

Connecting a Computer ...................................

E-65

 

 

MIDI Settings....................................................

E-66

 

 

Storing and Loading Digital Keyboard

 

 

 

Memory Data....................................................

E-68

 

 

Connecting to Audio Equipment.......................

E-69

 

 

 

 

 

 

Included Accessories

 

Separately Available Accessories

Music Stand

 

• You can get information about accessories that

Song Book

 

are separately for this product from the CASIO

Leaflets

 

catalog available from your retailer, and from the

• Safety Precautions

 

CASIO website at the following URL.

• Appendix

 

 

• Other (Warranty, etc.)

 

http://world.casio.com/

Items included as accessories are subject to change without notice.

 

 

 

 

 

English

E-3

Casio WK-500, WK-200 User Manual 2

General Guide

In this manual, the term “Digital Keyboard” refers to the WK-200/WK-500.

Illustrations in this User’s Guide show the WK-500.

In this manual, buttons and other controllers are identified using the numbers shown below.

2 1

3

4

5

6

7

8 9 bk bl bm bn bo

bs

bp bq br

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

bt

ck cl cm cn co

 

cp cq cr

 

cs ct

dk

dl

dm

 

 

 

 

dn do dp

 

 

dq

 

 

 

 

dl

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

dr

ds

dt

ek

E-4

General Guide

1 POWER button E-9, 24, 44, 47, 49, 55, 68

ck Area1, TR2, WATCH button

2 MAIN VOLUME knob E-9

E-19, 31, 46, 47, 50, 55

 

3 MIC VOLUME knob E-17

cl Area2, TR3, REMEMBER button

E-19, 32, 46, 47, 50, 55

 

4 PRESET SCALE button (WK-200)

cm Area3, TR4, NEXT button E-19, 30, 46, 47, 50, 55

SCALE EDITOR button (WK-500) E-53, 54, 55

 

5 RECORDER button E-48, 49, 50, 51, 52

cn Area4, TR5, AUTO button E-19, 34, 46, 47, 50, 55

 

6 RHYTHM EDITOR button E-42, 43

co STORE, TR6, MUSIC CHALLENGE button

E-19, 35, 47, 50, 55

 

7 METRONOME, BEAT button E-11

cp SPLIT button E-13, 14

 

8 INTRO, REPEAT button E-27, 32, 39, 42, 43

cq LAYER button E-13, 16

 

9 NORMAL/FILL-IN, REW button

cr AUTO HARMONIZE/ARPEGGIATOR, TYPE button

E-26, 30, 36, 39, 42, 43

E-41, 56, 57

 

bk VARIATION/FILL-IN, FF button

cs SAMPLING button E-18, 19, 20, 21

E-26, 30, 39, 42, 43

 

bl SYNCHRO/ENDING, PAUSE button

ct FUNCTION button E-6

 

E-26, 39, 40, 42, 43

dk CARD, SAVE/LOAD button (WK-500 only)

bm START/STOP, PLAY/STOP button

E-60, 61, 62, 63, 64

 

E-25, 26, 28, 31, 32, 36, 48, 50, 51, 52, 64

dl Speakers

bn ACCOMP ON/OFF, CHORDS, PART SELECT

dm Song Bank list

button E-25, 28, 30, 32, 37, 41, 42, 43, 52, 67

dn Music Preset list

 

bo TEMPO buttons E-11, 27, 40

do Display

 

bp TONE, MUSIC PRESET button

dp Rhythm list

E-9, 12, 18, 20, 21, 22, 24, 56

 

bq RHYTHM, ONE TOUCH PRESET button

dq Tone list

 

E-12, 19, 20, 22, 36, 40, 43, 47, 48, 51, 55

dr PITCH BEND wheel (WK-500 only) E-16

br SONG BANK button E-26, 28, 30, 51

ds CHORD root names E-37

bs Number buttons, [–]/[+] buttons E-6

dt Percussion instrument list E-12

bt BANK, CHORD/TR1, LISTEN button

ek SD CARD SLOT (WK-500 only) E-60

E-19, 31, 46, 47

 

English

 

el

 

 

em en eo ep eq

 

er

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

el em en

eo

USB port E-65

SUSTAIN/ASSIGNABLE JACK E-15

PHONES/OUTPUT jack (WK-200)

PHONES jack (WK-500) E-9, 69

AUDIO IN jack E-17, 69

ep

eq er

DC 9V terminal (WK-200)

DC 12V terminal (WK-500) E-8

MIC IN jack E-17

LINE OUT R, L/MONO jack (WK-500 only)E-69

E-5

General Guide

Using the 10-key Pad (bs)

Use the number buttons and the [–] and [+] buttons to change the settings of the parameters that appear in the upper left area of the display.

Setting

S t . G r P n o

Number Buttons

Use the number buttons to enter numbers and values.

Enter the same number of digits as the currently displayed

value.

Example: To enter tone number 001, input 0 3 0 3 1.

Negative values cannot be input using the number buttons. Use [–] (decrease) and [+] (increase) instead.

[–]and [+] Buttons

You can use the [–] (decrease) and [+] (increase) buttons to change the displayed number or value.

Holding down either button scrolls the displayed setting.

Pressing both buttons at the same time will revert to the initial default setting or the recommended setting.

FUNCTION Button (ct) Functions

You can use the FUNCTION button (ct) to adjust the reverb effect, to delete data, and to perform a wide range of other Digital Keyboard operations.

To select a function

1.Press ct to display the function menu.

2.Use the bs (10-key) [4] ( ) and [6] ( ) keys to display the function you want.

You can exit the function menu by pressing ct.

After selecting functions 8 through 12, press the bs (10-key) [7] (ENTER) key to display the menu item’s submenu. Then use [4] ( ) and [6] ( ) to select an item. You can exit a submenu by pressing the bs (10-key) [9] (EXIT) key.

3.Refer to the indicated pages for details about each function.

E-6

 

Function

Display

See

 

Page

 

 

 

1

Transpose

Trans.

E-15

 

 

 

 

2

Accompaniment Volume

AcompVol

E-40

 

 

 

 

3

Song Volume

Song Vol

E-28

 

 

 

 

4

Touch Response

Touch

E-10

 

 

 

 

5

Tuning

Tune

E-15

 

 

 

 

6

Reverb

Reverb

E-14

 

 

 

 

7

Chorus

Chorus

E-14

 

 

 

 

8

Sampling

SAMPLING

 

 

 

 

 

 

Automatic Sampling Start

AutoStrt

E-22

 

Automatic Sampling Stop

AutoStop

E-23

 

Sampled Tone Protect

(Protect)

E-24

 

 

 

 

9

Step Up Lesson

LESSON

 

 

 

 

 

 

Voice Fingering Guide

Speak

E-32

 

Note Guide

NoteGuid

E-33

 

Performance Evaluation

Scoring

E-33

 

Phrase Length

PhraseLn

E-33

 

 

 

 

10

Other Settings

OTHER

 

 

 

 

 

 

Arpeggiator Hold

ArpegHld

E-57

 

Pedal Effect

Jack

E-15

 

Pitch Bend Range

Bend Rng

E-16

 

(WK-500 only)

 

 

 

Accompaniment Scale

AcompScl

E-55

 

LCD Contrast

Contrast

E-10

 

 

 

 

11

MIDI Settings

MIDI

 

 

 

 

 

 

Keyboard Channel

Keybd Ch

E-66

 

Navigate Channels

Navi. Ch

E-66

 

Local Control

Local

E-67

 

Accomp Out

AcompOut

E-67

 

 

 

 

12

Delete

DELETE

 

 

 

 

 

 

Sampled Sound Delete

(tone name)

E-23

 

User Rhythm Delete

(rhythm name)

E-45

 

User Song Delete

(song name)

E-57

 

All Data Delete

All Data

E-58

 

 

 

 

The tone and other parameters revert to their initial defaults whenever you turn on power (page E-9).

General Guide

English

E-7

Getting Ready to Play

Preparing the Music Stand

Music stand

Power Supply

Either an AC adaptor or batteries can be used to power this Digital Keyboard. Normally, use of AC adaptor power is recommended.

The AC adaptor does not come with this Digital Keyboard. Purchase it separately from your retailer. See page E-3 for information about options.

Using the AC Adaptor

Use the AC adaptor when you want to power the Digital Keyboard from a household electrical outlet.

Specified AC Adaptor: AD-5 (WK-200)

AD-12 (WK-500)

DC 9V terminal (WK-200)

AC adaptor

DC 12V terminal (WK-500)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Household power outlet

Be sure to turn off Digital Keyboard power before connecting or disconnecting the AC adaptor.

Using Batteries

Be sure to turn off power before loading batteries.

It is up to you to prepare six commercially available D-size batteries. Do not use oxyride batteries or any other nickel based batteries.

1.Open the battery cover on the bottom of the Digital Keyboard.

2.Load six D-size batteries into the battery

compartment.

Make sure the positive + and negative - ends of the batteries are facing as shown in the illustration.

3.Insert the tabs of the battery cover into the holes on the side of the battery compartment, and close the cover.

Tabs

Low Battery Indication

The indicator shown below starts to flash to let you know when battery power is low. Replace the batteries with new ones.

Low battery indicator (flashes)

E-8

Playing the Digital Keyboard

21

7

bp bs

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

bo

ct

English

Turning on Power and Playing

1.Press 1.

This turns on power.

2.Try playing something on the keyboard. Use 2 to adjust volume.

Decrease

Increase

Turning off the Digital Keyboard causes most current settings to be cleared. The Digital Keyboard will revert to initial settings the next time you turn it on.

This is true for all settings except for sample sound protection. Once you turn it on it remains on until you turn it off again.

Auto Power Off (Using Batteries)

While you are using batteries for power, power will turn off automatically if you do not perform any operation for about six minutes. Auto Power Off is disabled while the AC adaptor is being used for power.

Disabling Auto Power Off

You can disable Auto Power Off to ensure that power is not turned off automatically during a concert, etc.

1.While holding down bp, turn on power.

Auto Power Off will be disabled.

Using Headphones

Using headphones cuts off output from the built-in speakers, which means you can practice playing even late at night without disturbing others.

Be sure to turn down the volume level before connecting headphones.

PHONES/OUTPUT jack (WK-200)

PHONES jack (WK-500)

Headphones do not come with the Digital Keyboard.

Use commercially available headphones. See page E-3 for information about options.

Do not listen to very high volume output over headphones for long period. Doing so creates the risk of hearing damage.

If you are using headphones that require an adaptor plug, make sure you do not leave the adaptor plugged in when removing the headphones.

E-9

Playing the Digital Keyboard

 

Changing Keyboard Response to

 

Changing Touch Response Sensitivity

 

 

Touch Pressure

 

Use the procedure below to control how much the volume of

 

 

played notes change in accordance with playing speed.

 

 

(Touch Response)

 

 

 

 

Select the setting that best matches your playing style.

 

Touch Response alters tone volume in accordance with

 

1. Press ct and then use the bs (10-key) [4] (

)

keyboard pressure (speed). This provides you some of the

 

 

 

and [6] (

) keys to display “Touch” (page

 

same expressivity you get on an acoustic piano.

 

 

 

 

 

E-6).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Keyboard Instrument Sound Intensity

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

T o u c h

 

Sound intensity depends on the speed that keys

 

 

 

 

 

are pressed.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

People normally believe that the stronger the pressure applied

 

2. Use bs (10-key) [–] and [+] keys to select one of

to a piano keyboard, the louder the sound. Actually, however,

 

the intensity of the notes played depends on the speed at

 

 

the three Touch Response sensitivity settings.

which keys are pressed. Notes are louder when keys are

 

 

 

 

 

 

 

 

 

 

 

pressed quickly, and quieter when keys are pressed slowly.

 

Off (oFF)

Touch Response is turned off. Sound

 

Keeping this in mind as you play a keyboard musical

 

 

 

volume is fixed, regardless of key press

 

instrument lets you control note volume without striving to

 

 

 

 

 

 

 

speed.

 

apply too much pressure with your fingertips.

 

 

 

 

 

Type 1 (1)

Normal Touch Response

 

 

 

 

 

 

 

The playability of an acoustic piano

 

Type 2 (2)

More sensitive Touch Response than Type 1

Your Digital Keyboard provides you with key touch that is the

 

 

 

 

 

 

 

 

 

 

 

next best thing to an acoustic piano. Note volume changes

 

 

 

 

 

 

 

 

 

 

 

automatically in accordance with key press speed.

 

 

 

 

 

 

 

Indicator disappears when

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pressing fast produces

 

 

 

 

 

 

 

Touch Response is turned off.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Adjusting Display Contrast

 

 

 

 

louder notes.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1. Press ct and then use the bs (10-key) [4] (

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

and [6] (

) keys to display “OTHER” (page

 

 

 

 

 

 

 

E-6).

 

 

 

 

 

 

 

 

 

 

 

Pressing slowly produces

 

 

 

 

 

 

Flashes

 

 

 

 

softer notes.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

O T H E R

 

 

 

 

Do not try to use too much

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2. Press bs (10-key) [7] (ENTER) key.

 

 

 

 

pressure.

 

 

 

 

 

 

 

3. Use the bs (10-key) [4] ( ) and [6] ( ) keys

 

 

 

 

 

 

 

 

 

 

 

 

 

 

to display “Contrast”.

 

C o n t r a s t

4. Use the bs(10-key) [–] and [+] keys to adjust the contrast.

• The contrast setting range is 01 to 17.

E-10

Playing the Digital Keyboard

Using the Metronome

The metronome lets you play and practice along with a steady beat to help keep you on tempo.

Start/Stop

1.Press 7.

This starts the metronome.

This pattern changes with each beat.

2. Press 7 again to stop the metronome.

Changing the Beats Per Measure

You can configure the metronome to use a bell sound for the first beat of each measure of the song you are playing.

You can specify 0, or a value from 2 to 6 as the number of beat per measure.

When playing a built-in song, the beats per measure setting (which determines when the bell sounds) is configured automatically for the currently selected song.

1.Hold down 7 until the beats per measure setting screen appears on the display.

B e a t

If you do not perform any operation for a few seconds after the beats per measure setting screen appears, the display will return to the screen displayed before you pressed 7.

2.Use bs (10-key) to enter the number of beats per measure.

The bell will not sound if you specify 0 for this setting. In this case, all beats are indicated by a click sound. This setting lets you practice with a steady beat, without worrying how many beats there are in each measure.

Changing the Metronome Tempo

Use the following procedure to change the tempo of the metronome.

1.Press bo.

Use y (slower) and t (faster) to change the tempo setting. Holding down either button changes the setting at high speed.

Pressing t and y at the same time will initialize the tempo setting in accordance with the currently selected song or rhythm.

Pressing bo causes the tempo value to flash on the display. While the tempo value is flashing, you can use bs (10-key) to change it.

Note that you must input leading zeros, so 89 is input as 089.

The tempo value will stop flashing if you do not perform any operation for a short while.

Tempo value (flashes)

Changing the Metronome Sound Volume

The metronome volume setting is changed automatically with the volume level of the currently selected Auto Accompaniment or song. The metronome volume cannot be adjusted independently.

For information about changing the Auto Accompaniment volume, see page E-40.

For information about changing the song volume, see page E-28.

You cannot adjust the balance between the metronome and note volume during Auto Accompaniment and built-in tune play.

E-11

English

Controlling the Keyboard Sounds

bqbp bs

Select from a variety of musical instrument sounds

Your Digital Keyboard lets you select tones for a wide variety of musical instrument sounds, including violin, flute, orchestra, and more. Even the same song sound takes on a different feel by changing the instrument type.

To select an instrument for playing

1. Press bp.

Tone number

Tone name

S t . G r P n o

2.Use bs (10-key) to select the tone number you want.

The corresponding tone number and tone name will appear on the screen.

See the separate “Appendix” for a complete list of available tones.

Use the number buttons to enter the tone number. Specify

three digits for the tone number.

Example: To select 001, enter 0 3 0 3 1.

When one of the drum sets is selected, each keyboard key is assigned a different percussion sound.

cp cq

ct

3.Try playing something on the keyboard.

The tone of the instrument you selected will sound.

Playing with a Piano Tone (Piano Setup)

1.Press bp and bq at the same time.

This selects the grand piano tone.

Settings

 

Tone Number

: “001”

Reverb

: “06”

Transpose

: 00

Touch Response

: Off: Returns to initial default

 

On: No change

Pedal Effect

: SUS

Rhythm Number

: “161” (WK-200), “181” (WK-500)

Accompaniment

: Rhythm part only

Local Control

: On

Drum Assign

: Off

Split

: Off

Layer

: Off

Chorus

: Off

Octave Shift (Upper): 0

Auto Harmonize

: Off

Arppegiator

: Off

Scale

: Equal

E-12

Controlling the Keyboard Sounds

Layering Two Tones

You can use the following procedure to layer two different tones (such as piano and strings) so they sound simultaneously when you press a keyboard key.

1.Select the first tone you want to use.

Press bp and then use bs (10-key) to select the tone you want.

Example: 026 ELEC.PIANO 1 (WK-500)

E . P i a n o 1

2. Press cq.

Lights

3.Use bs (10-key) to select the second tone you want.

Example: 212 STRINGS (WK-500)

S t r i n g s

4.Play something on the keyboard.

Both tones sound at the same time.

5.Pressing cqagain to unlayer the keyboard (so it plays only the tone you selected in step 1).

Each press of cq toggles between layered (two tones) and unlayered (one tone).

Splitting the Keyboard between Two Different Tones

You can use the procedure below to assign different tones to the right range and left range of the keyboard, so it sounds like you are playing an ensemble between two instruments.

To select the two tones for a split keyboard

1.Select the tone for the right side range (page E-12).

Press bp and then use bs (10-key) to select the tone you want.

Example: 335 FLUTE 1 (WK-500)

F l u t e 1

2. Press cp.

Lights

3.Use bs(10-key) to select the left side range tone you want.

Example: 056 VIBRAPHONE 1 (WK-500)

V i b e s 1

4.Play something on the keyboard.

This will sound the tones assigned to the left and right side ranges of the keyboard.

VIBRAPHONE 1

FLUTE 1

Split point

Disappears

F3

English

E-13

Controlling the Keyboard Sounds

5. Pressing cp again to unsplit the keyboard (so it

 

 

 

 

Using Reverb

 

plays only the tone you selected in step 1).

 

• Each press of cp toggles between split (two tones) and

Reverb adds reverberation to notes. You can change the

 

unsplit (one tone).

duration of the reverb.

 

 

 

 

 

 

1. Press ct and then use the bs (10-key) [4] ( )

 

 

 

 

 

 

 

 

 

 

 

 

 

and [6] (

) keys to display “Reverb” (page

 

 

 

 

 

 

 

E-6).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

R e v e r b

 

 

 

 

 

 

 

 

 

 

 

Disappears

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2. Use the bs(10-key) [–] and [+] keys to select the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• If you turn on both layer and split, layering will be applied to

 

reverb setting you want.

 

the right side range of the keyboard only.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Off (oFF)

Turns off reverb.

To change the split point

1 to 10 The larger the number selected, the longer

1. the reverb duration.

While holding down cp, press the keyboard key where you want the split point to be.

The key you press will become the lowest note of the right

 

R e v e r b

 

side range of the split keyboard.

 

 

 

 

 

 

Example: Setting middle C (C4) as the split point.

 

 

 

 

Key name

 

 

 

 

Indicator disappears when reverb is turned off.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C

4

 

 

 

 

 

 

Using Chorus

 

 

 

Chorus is a function that adds depth and breadth to notes. It

 

 

 

 

 

 

makes you sound as if you are playing multiple instruments.

1. Press ct and then use the bs (10-key) [4] ( ) and [6] ( ) keys to display “Chorus” (page E-6).

C h o r u s

2. Use the bs(10-key) [–] and [+] keys to select the chorus type you want.

There are five chorus types, plus an off setting.

C h o r u s

Indicator disappears when chorus is turned off.

• The actual effect produced by chorus depends on the tone you are using.

E-14

Controlling the Keyboard Sounds

Using a Pedal

A pedal can be used to change notes in various ways while playing.

A pedal unit does not come with the Digital Keyboard. Purchase one separately from your retailer. See page E-3 for information about options.

Connecting a Pedal Unit

Connect an optional pedal unit.

SUSTAIN/ASSIGNABLE JACK

Selecting the Pedal Effect

1. Press ct and then use the bs (10-key) [4] ( ) and [6] ( ) keys to display “OTHER” (page E-6).

Flashes

O T H E R

2.Press bs (10-key) [7] (ENTER) key.

3.Use the bs (10-key) [4] () and [6] () keys to display “Jack”.

J a c k

4.Use the bs(10-key) [–] and [+] keys to select the pedal effect you want.

The following shows the available pedal effects.

Sustain

Sustains notes played while the pedal is

(SUS)

depressed. Organ and other similar tone

 

notes are sustained even if the pedal is not

 

pressed.

Sostenuto

Sustains notes that are playing when the

(SoS)

pedal is depressed before the keyboard keys

 

are released.

Soft

Slightly softens notes played while the pedal

(SFt)

is depressed.

Rhythm

Pressing the pedal starts and stops Auto

(rHy)

Accompaniment or song playback.

 

 

Changing the Pitch

(Transpose, Tuning, Octave Shift)

Changing the Pitch in Semitone Steps (Transpose)

The transpose feature lets you change the pitch, in semitone steps. A simple operation lets you instantly change the pitch to match that of a singer.

• The transpose setting range is –12 to +12 semitones.

1. Press ct.

T r a n s .

2.Use the bs(10-key) [–] and [+] keys to select the transpose setting you want.

Fine Tuning (Tuning)

Use the tuning feature when you need to adjust the pitch slightly to play along with another musical instrument. Also, some artists perform their music with slightly altered tuning. You can use the tuning feature to adjust tuning so it exactly matches a performance on a CD.

• The tuning setting range is –99 to +99 cents.

1.Press ct and then use the bs (10-key) [4] () and [6] () keys to display “Tune” (page E-6).

T u n e

2.Use the bs(10-key) [–] and [+] keys to adjust the tuning.

English

E-15

Controlling the Keyboard Sounds

Octave Shift

 

 

 

 

Using the Pitch Bend Wheel to

Octave Shift lets you raise or lower the pitch of the keyboard

 

Shift the Pitch of Notes

notes in octave units.

 

 

 

 

 

 

 

 

(WK-500 Only)

The octave shift setting range is –2 to +2 octaves.

 

 

 

When using Split (page E-13), you can individually set the

 

 

 

 

 

 

 

 

 

You can use the pitch bend wheel to slide the pitch of notes

 

left and right keyboard ranges to the pitches you want.

 

 

 

smoothly upwards and downwards. This technique makes it

1. Keep pressing cq until the screen shown below

 

 

possible to produce effects that are similar to sounds

 

 

appears on the display.

 

 

 

 

produced when bending notes on a saxophone or electric

 

 

 

 

 

 

guitar.

 

 

If you want to use Split, turn on Split before pressing cq.

 

 

 

 

 

 

 

 

 

 

 

 

 

If you do not perform any operation for a few seconds

 

To play with the pitch bend wheel

 

 

 

 

 

 

after this screen appears, the display will return to the

 

 

 

 

previous screen automatically.

 

 

 

1. While playing a note on the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

keyboard, rotate the pitch bend

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

O c

t U p p e

r

 

 

 

 

 

 

 

wheel on the left of the keyboard

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

upwards or downwards.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The amount the note bends depends on how

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2. Use the bs (10-key) [–] and [+] keys to shift the

 

 

much you rotate the pitch bend wheel.

 

 

 

 

 

 

• Do not have the pitch bend wheel rotated

 

 

 

 

 

 

octave.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

as you turn on the Digital Keyboard.

 

 

Split On : This step affects the right side keyboard

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

range only.

 

 

 

 

Specifying the Pitch Bend Range

 

 

 

 

 

 

 

 

 

Split Off : This step affects the entire keyboard range.

 

 

 

 

Use the following procedure to specify how much the pitch of

3. Press cq.

 

 

 

 

 

 

 

 

the note changes whenever the pitch bend wheel is rotated

 

 

• Split On : The screen shown below will appear. Use the

 

upwards or downwards. You can specify a range from 0 to 12

 

 

 

bs (10-key) [–] and [+] keys to shift the

 

 

 

semitones (one octave).

 

 

 

octave for the left side keyboard range.

 

1. Press ct and then use the bs (10-key) [4] ( )

 

 

Split Off : The screen shown below will appear.

 

 

 

 

 

 

Advance to step 4.

 

 

 

 

and [6] ( ) keys to display “OTHER” (page

 

 

 

 

 

 

 

 

 

E-6).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

O c

t L o w e

r

 

 

Flashes

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4. Press cq again.

 

 

 

 

 

O T H E R

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2. Press bs (10-key) [7] (ENTER) key.

3. Use the bs (10-key) [4] () and [6] () keys to display “Bend Rng”.

B e n d R n g

4. Use the bs (10-key) [–] and [+] keys to change the range.

E-16

Sampling Sounds and Playing Them on the Digital

Keyboard

1 3

bqbp bs

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

btckclcmcnco

cs ct

You can sample a sound from a microphone, a portable audio player, or other device, and then play the sound on the keyboard. For example, you could sample the bark of your dog and then use the sound in a melody. You also can sample and use passages from a CD. The sampling feature is a great way to create new sounds that are highly creative.

Connection and Preparation

Before connecting, make sure that the Digital Keyboard, external devices, and/or the microphone all are turned off.

1.Connect a microphone or external device to the Digital Keyboard.

MIC IN jack

Digital Keyboard AUDIO IN jack

CD player, Cassette player, etc.

Stereo mini plug

You also could connect a commercially available microphone.

Connection of an external device requires commercially available connecting cords, supplied by you. Connecting cords should have a stereo mini plug on one end and a plug that matches the configuration of the external device on the other end.

2.Turn down the volume levels of the external device and the Digital Keyboard.

3.Turn on the external device or microphone, and then turn on the Digital Keyboard.

When using a microphone, adjust the input volume level with 3.

It will take a few seconds after you turn on the Digital Keyboard before you will be able to use the microphone.

Sampled sounds are recorded in monaural.

English

E-17

Sampling Sounds and Playing Them on the Digital Keyboard

Sampling and Playing a Melody

Sound (Melody Sampling)

Use the procedures in this section to sample a sound and play it as the melody part on the Digital Keyboard.

Up to five sampled sounds can be stored in Digital Keyboard memory as tone numbers 671 through 675 (WK200: 571 through 575). Simply select the tone number where the sound you want is located to assign the sound to the keyboard.

To sample a sound

1.Press bp and then use bs (10-key) to enter the tone number (WK-500: 671 to 675) (WK-200: 571 to 575) where you want to store the sampled sound.

No sampled sound stored

N o D a t a

Lights

In place of the above steps, you could press cs and bp at the same time and then select a tone number.

2.Press cs.

This enters sampling standby.

The allowable sampling time (in seconds) will appear on the display momentarily and then the display will change to the following.

W a i ti n g

Flashes

3.Output the sound from the external device. In the case of a microphone, output the sound in the direction of the microphone.

Sampling will start automatically.

S a m p l i n g

4.After the sound you want to sample is finished, press cs.

Sampling will stop when you release cs.

Even if you do not press cs, sampling will stop automatically whenever there is no more sound being input from the external device or microphone. Sampling also will stop automatically 10 seconds after it is started.

Sampled sound 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

S 1 : O r g n l

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Used memory

 

 

 

 

 

 

 

Remaining memory

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(Unit: Kbytes)

 

 

 

 

 

 

capacity

5. Play something on the Digital Keyboard.

You may not be able to get 10 seconds of sampling if Digital Keyboard memory is low due to storage of other data. If this happens, deleting other memory data you no longer need will free up memory space and you should be able to sample for 10 seconds. See “Deleting a Sampled Sound” on page E-23 for more information.

Sampling sound and storing it will delete any sound data currently stored under the same tone number. To help ensure that you do not accidentally delete important data, be sure to read “Protecting Against Accidental Deletion of Sampled Sounds” on page E-24.

Lights

E-18

Sampling Sounds and Playing Them on the Digital Keyboard

How sampled sounds are played

Pressing Middle C (C4) will play back the original sound. The keys to the left and right of C4 play the sound at different pitches.

C4

Looping a Sampled Sound

You can use the following procedure to loop a sampled sound so it continues to repeat, as you play on the Digital Keyboard.

1.Press bq.

2.While holding down cs, press co.

This enters repeat standby.

F u n k 8 B t

Lights

3.Press the button (bt to cn) that corresponds to the melody sampling tone number you want to select.

This will start looped playback of the selected sound.

To select this tone number:

Press this button:

WK-500

WK-200

 

671

571

bt

 

 

 

672

572

ck

 

 

 

673

573

cl

 

 

 

674

574

cm

 

 

 

675

575

cn

 

 

 

4.Press the same button again to stop playback.

5.Press co to return to the screen that was displayed before step 2 of this procedure.

Changing the Volume of Sampled Sound

Looped Playback

You can use the following procedure to change the volume level of the looped playback of each sampled sound, if you want.

1.Press the button of the sampled sound whose volume you want to change (bt to cn).

This will cause the sounds loop to sound.

2.While the loop is sounding hold down the same sampled sound button (bt to cn) as you press any keyboard key.

Pressing the keyboard key quickly will increase sample sound volume, while pressing slowly will decrease volume.

3.After the sampled sound is at the volume level you want, release its button (bt to cn).

English

E-19

Sampling Sounds and Playing Them on the Digital Keyboard

Applying Effects to a Sampled Sound

You can apply various effects to sampled sounds.

1.Press bp and then use bs (10-key) to enter the tone number (WK-500: 671 to 675) (WK-200: 571 to 575) to which you want to apply effects.

2.Press bp to cycle thorough the available effects, described below.

Effect Type

Description

(Display)

Original (Orgnl)

Normal sampled tone (no looping, no effect).

Loop 1 (Loop1) Loops the sampled sound.

Loops the sample sound and raises the Loop 2 (Loop2) pitch of the resonating sound when the

keyboard key is released.

Loops the sample sound and lowers the Loop 3 (Loop3) pitch of the resonating sound when the

keyboard key is released.

Pitch 1 (Ptch1)

Changes the pitch from low to high, at an increasing rate.

Pitch 2 (Ptch2)

Changes the pitch from high to low, at a decreasing rate.

Changes the pitch from high to low, at a Pitch 3 (Ptch3) decreasing rate, and then raises the pitch

when the key is released.

Tremolo (Treml) Alternates volume between high and low.

Adds vibrato and changes the pitch by a Funny 1 (Funy1) gradually increasing amount.

Alternates between high pitch and low Funny 2 (Funy2) pitch.

Adds vibrato and changes the pitch from Funny 3 (Funy3) low to high.

Avoid assigning the same sampled sound to the keyboard for play along and for looped play. Doing so will cause, the Loop 1 effect to be applied to the keyboard tone while looped play of the sampled sound is being performed.

Incorporating a Sampled Sound into a Drum Set (Drum Sampling)

You can use the procedure to change the drum sounds that are assigned to each keyboard key.

You can store up to three drum sets and store them as tone numbers 676, 677, and 678 (WK-200: 576, 577, and 578). Simply select the tone number where the drum set you want is located to assign the drum set sounds to the keyboard.

1.Press bq. bq lights.

2.Press bp and then use bs (10-key) to enter the tone number (WK-500: 676, 677, or 678) (WK-200: 576, 577, or 578) for the drum set whose sounds you want to change.

N o D a t a

Lights

In place of the above steps, you could press cs and bq at the same times and then select a tone number.

3.Press cs.

N o Da t a

Flashes

4.Press the keyboard key to which you want to assign the drum sound you are about to sample.

This enters sampling standby.

The allowable sampling time (in seconds) will appear on the display momentarily and then the display will change to the following.

W a i ti n g

Flashes

E-20

Sampling Sounds and Playing Them on the Digital Keyboard

5.Output the sound from the external device. In the case of a microphone, output the sound in the direction of the microphone.

Sampling will start automatically.

S a m p l i n g

Lights

6.After the sound you want to sample is finished, press cs.

S m p l D r m 1

Remaining memory capacity

Sampling will stop when you release cs.

Even if you do not press cs, sampling will stop automatically whenever there is no more sound being input from the external device or microphone. Sampling also will stop automatically 10 seconds after it is started.

7.Press the keyboard key.

You can repeat steps 3 through 6 to change other sounds that make up the currently selected drum set. There are eight sounds per drum set.

You may not be able to get 10 seconds of sampling if Digital Keyboard memory is low due to storage of other data. If this happens, deleting other memory data you no longer need will free up memory space and you should be able to sample for 10 seconds. See “Deleting a Sampled Sound” on page E-23 for more information.

Sampling a sound will delete any sound data currently assigned to the same keyboard key. To help ensure that you do not accidentally delete important data, be sure to read “Protecting Against Accidental Deletion of Sampled Sounds” on page E-24.

Editing Sampled Drum Set Sounds

You can use the procedures in this section to copy the drum sound assigned to one keyboard key to another key, to change the pitch of a sound, and to delete a sampled sound.

1.Press bp and then use bs (10-key) to enter the tone number (WK-500: 676, 677, or 678) (WK200: 576, 577, or 578) for the drum set you want.

2.Press cs.

3.Press ct.

S m p lD r m 1

Flashes at high speed

This is the editing mode.

While in the editing mode, you can copy a sound, change the pitch of a sound, or delete a sound (each of which is described below). Pressing ct again exits the editing mode and returns to step 2 of this procedure.

Indicates keyboard keys that have sounds assigned.

To copy a sampled sound from one key to another

While holding down the keyboard key to which the sampled sound you want to copy is assigned, press the keyboard key to which you want to copy it.

Example: To copy sampled sound of key C4 to key D4

Indicates the keyboard key whose sound was copied.

A keyboard key that already has a sampled sound assigned cannot be selected as a copy destination.

English

E-21

Sampling Sounds and Playing Them on the Digital Keyboard

To change the pitch of a sampled sound

While holding down the keyboard key of the sampled sound whose pitch you want to change, use the bs (10-key) [–] and [+] keys to change the pitch.

You can change the pitch within a range of –64 to 63 semitones.

To delete a keyboard key’s sampled sound

While holding down the keyboard key whose sound you want to delete, press bq. In response to the “DelSure?” message that appears, press the bs (10-key) [+] button to delete, or [–] to cancel the delete operation.

Deleting a sampled sound will return the key to its initial default built-in sound.

Example: To delete the sound assigned to key D4

Disappears

Using a Drum Sampling Tone in Auto

Accompaniment

Use the following procedure to change the rhythm part of an Auto Accompaniment pattern to a drum set sound that you sampled.

1.Press bq and then use bs (10-key) to enter the rhythm number of the Auto Accompaniment pattern you want.

You cannot use a Drum Sampling Tone in a user rhythm, so do not select a user rhythm in the above step.

2.Press bp and then use bs (10-key) to enter the tone number of the sampling drum set that contains the sound you want to use.

3.Press bp.

This changes the rhythm part of the Auto Accompaniment pattern you selected in step 1 to the sampled sound you selected in step 2.

To change the Auto Accompaniment rhythm part back to its original sound, press bp again.

Some rhythm part drum sounds cannot be replaced by sampled sounds.

Other Sampling Functions

Changing to a Manual Sampling Start

Normally when the Digital Keyboard is in sampling standby, it will start sampling automatically whenever it detects sound input. You can use the following procedure to enable manual sampling start, which will cause sampling to wait until you press a button to start it. You can use this to insert silence before the sampled sound.

1.Press ct and then use the bs (10-key) [4] ( ) and [6] ( ) keys to display “SAMPLING” (page E-6).

Flashes

S A M P L I N G

2. Press the bs (10-key) [7] (ENTER) key.

A u t o S t r t

3.Press the bs (10-key) [–] key to turn off automatic sampling start.

This enables manual sampling start, which operates as described below.

Melody sampling (page E-18):

Sampling starts when you release cs, which you press in step 2 of the sampling procedure.

Drum sampling (page E-20):

Sampling starts when you release the Digital Keyboard key you press in step 4 of the sampling procedure.

When manual sampling start is enabled, sampling starts when you release cs or the keyboard key, not when you press it. Sampling does not start if you hold down the button or key.

E-22

B

 

Loading...
+ 56 hidden pages