CARVIN ENGINEERING DATA BR SERIES BASS ENCLOSURES INSTRUCTIONS
BR810 BR410
BR210
BR115
BR118
BR210/410/115/118/810 BASS SPEAKER SYSTEM SPECS:
Model |
BR210 |
BR410 |
BR810 |
BR115 |
BR118 |
Frequency Response: |
64 to 20K |
60 to 20K |
58 to 20K |
45 to 20K |
38 to 2K |
Low end Response -10DB: |
50Hz |
40Hz |
38Hz |
35Hz |
30Hz |
1” Titanium horn driver: |
yes |
yes |
yes |
yes |
no |
Main Driver: |
2x 10” |
4x 10” |
8x 10” |
1x 15” |
1x 18” |
Power Handling: |
400 watts |
800 watts |
1200 watts |
600 watts |
800 watts |
6 Position horn attenuation: |
yea |
yes |
yes |
yes |
no |
Horn Protection: |
yes |
yes |
yes |
yes |
N/A |
Horn coverage angle: |
90x90 |
90x90 |
90x90 |
90x90 |
N/A |
Nominal Impedance: |
4Ω |
8Ω |
4 |
4 |
4Ω |
Speaker Connectors: |
I-----------------2 Speakon™ and 2 1/4" Connector-----------------I |
||||
Enclosure type: |
Sealed |
Sealed |
Ported |
Ported |
Ported |
Enclosure Covering: |
Duratuff II™ |
|
|
|
|
Dimensions: |
|
|
|
|
|
Width: |
23.5" |
23.5" |
23.5" |
23.5" |
23.5" |
Depth: |
18.25" |
18.25" |
18.25" |
18.25" |
18.25" |
Height: |
17.5" |
25.5" |
47.75" |
25.5" |
25.5" |
Warranty (LBS): |
43 |
68 |
118 |
56 |
62 |
Optional Vinyl Cover: |
CVS210 |
CV115 |
CV810 |
CV115 |
CV115 |
Optional Casters: |
CTS4 |
CTS4 |
N/A |
CTS4 |
CTS4 |
For your records, you may wish to record the following information.
Serial No._____________________ Invoice Date_______________
76-00410B 0705
The BR series cabinets incorporate very efficient Low Frequency drivers delivering accurate tone with high output. Expect a deep resonate bass from these systems along with a tight, punchy, slap & pop high-end. Extended mid range also makes your bass sound alive.
•Titanium HF driver for crisp-slap highs
•Cross grain laminated multi-ply plywood enclosure construction
•Heavy internal bracing eliminates unwanted cabinet resonance
•Dado joints are assembled with 3000 lbs tensile strength glue
•16 ga. perforated steel grill
•Tear resistant black Duratuff™ covering and recessed retractable handles
Accepts Speakon™ & 1/4” cables
REAR CONNECT PLATE
Two standard 1/4" phone jacks and two high current Speakon™ connectors are featured. One for connecting to the power amp and the other for connecting to an additional speaker system.
HORN ATTENUATION SWITCHES
The rear crossover panel features a set of attenuation switches to control the volume of the 1” Titanium HF Driver. This will allow you to turn the Driver full on or reduce by 3dB increments to fine tune your treble response.
SPEAKER CABLES
12 gauge Speakon™ speaker cables will provide a secure connection and high current transfer of power to the speakers. You can also use standard 1/4" speaker cables instead of the Speakon™ cables provided they are at least 16 gauge. You can DAISY-CHAIN up to one additional speaker per cable by using the unused OUTPUT jack (right side) on your speaker jack plate. Be sure to note the total impedance to the amp so it is not lower than it’s recommended impedance. See Typical Loudspeaker Impedance Configurations.
TYPICAL LOUDSPEAKER IMPEDANCE CONFIGURATIONS
Individual speaker or speaker cabinet wiring examples for total impedance.
|
|
8Ω TOTAL |
SERIES CONNECTION |
|
PARALLEL CONNECTION |
|
SERIES/PARALLEL |
|||
|
IMPEDANCE |
16Ω TOTAL IMPEDANCE |
|
4Ω TOTAL IMPEDANCE |
|
CONNECTION |
||||
|
|
|
|
|
|
|
|
|
8Ω TOTAL IMPEDANCE |
|
|
+ |
+ |
+ |
+ |
|
|
+ |
+ |
+ |
+ |
8Ω |
|
8Ω 16Ω |
8Ω |
4Ω |
|
8Ω |
8Ω |
|||
|
|
|
|
8Ω |
|
|||||
|
|
|
|
|
|
|
|
|
|
+ |
|
|
|
|
|
|
|
|
|
|
8Ω |
|
|
|
|
|
|
|
|
|
|
+ |
|
|
|
|
+ |
|
|
|
+ |
|
8Ω |
|
|
|
|
8Ω |
|
|
|
|
||
|
|
|
|
|
|
|
8Ω |
|
+ |
|
|
|
|
|
|
|
|
|
|
|
8Ω |
PRECAUTIONS
1) DO NOT EXCEED THE POWER RATING marked on the rear connect plate. Excessive power will destroy drivers. 2) DISTORTION from power amps will destroy drivers much faster than clean power. 3) WATER, MOISTURE, and DUST are harmful to drivers causing failure which is not covered under warranty.
RECEIVING INSPECTION
INSPECT YOUR SPEAKER FOR ANY DAMAGE which may have occurred during shipping. If any damage is found, please notify the shipping company & CARVIN.
SAVE THE CARTON & ALL PACKING MATERIALS. In the event you have to re-ship your unit. CARVIN and the shipping company are not liable for any damage caused by improper packing for returns.
SAVE YOUR INVOICE. It will be required for warranty service if needed in the future. SHIPMENT SHORTAGE. Items may have been shipped separately. Please allow several days for the rest of your order to arrive before inquiring.
RECORD THE SERIAL NUMBER on the enclosed warranty card or below on this manual for your records. Keep your portion of the card and return the portion with your name and comments to us.
WARRANTY
CARVIN loudspeakers are covered by a ONE year limited warranty unless otherwise stated. Warranty coverage is limited to original manufactures defects only. WARRANTY DOES NOT COVER: 1) Opened or burned voice coils. 2) Torn cones caused by improper packing or abuse. 3) Damage from rain, moisture, ETC. When returning defective driver(s), remove them from the enclosure to reduce shipping costs. DO NOT stuff paper into the driver(s). Return pre-paid by UPS. Include your address and description of the problem. Your driver(s) will be returned COD for the cost of shipping and reconditioning if not covered under warranty.
12340 World Trade Drive, San Diego, CA 92128
800.854.2235 www.carvin.com
Loading...