Canon 6093B004, HF M52, HF M50, HF M500, 6096B001 User Manual

...
0 (0)

PUB. DIE-0416-000B

HD Camcorder

Instruction Manual

COPY

- ,

Important Usage Instructions

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

COPYRIGHT WARNING:

Unauthorized recording of copyrighted materials may infringe on the rights of copyright owners and be contrary to copyright laws.

The Mains plug is used as the disconnect device. The Mains plug shall remain readily operable to disconnect the plug in case of an accident.

CAUTION:

Danger of explosion if the wrong type of batteries are attached. Use only the same type of batteries.

Do not expose batteries or product to excessive heat such as the inside of a car under direct sunlight, fire, etc.

While using the compact power adapter, do not wrap it or cover it with a piece of cloth, and do not place it in confined narrow spaces.

CAUTION:

COPYCAUTION

RISK F ELECTRIC SH CK

DO N T EN

TO REDUCE THE RISK OF ELE TRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVI EABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure, that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point, within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

2

FCC/IC NOTICE

HD Camcorder, VIXIA HF M52 / VIXIA HF M50 / VIXIA HF M500 systems

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and use in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules. Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If such changes or modifications should be made, you could be required to stop operation of the equipment.

Model ID0008 (including WLANCOPYModule Model WM217)

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

The available scientific evidence does not show that any health problems are associated with using low-power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low-power wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure to low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. This model has been tested and found to comply with FCC/IC radiation exposure limits set forth for an uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules.

Canon U.S.A., Inc.

One Canon Plaza, Lake Success, NY 11042, U.S.A.

Tel No. (516)328-5600

This Class B digital apparatus complies with Canadian ICES-003.

3

IMPORTANT SAFETY INSTRUCTIONS

In these safety instructions the word “apparatus” refers to the Canon HD Camcorder VIXIA HF M52 / VIXIA HF M50 / VIXIA HF M500 and all its accessories.

1 Read these instructions.

2 Keep these instructions.

3Heed all warnings.

4Follow all instructions.

5 Do not use this apparatus near water.

6Clean only with dry cloth.

7Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

8Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

9Only use attachments/accessories specified by the manufacturer.

10Unplug this apparatus during lightning storms or when unused for long periods of time.

11Refer all servicing to qualified service personnel. Servicing is required when the apparatus

has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallenCOPYinto the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

REGIONS OF USE

VIXIA HF M52 and VIXIA HF M50 are in compliance (as of January 2012) with the radio signal regulations of the regions listed below. For details on other regions where they can be used, make inquiries with the contacts listed on the back side of this instruction manual.

REGIONS

Canada, Hong Kong S.A.R., USA

Model

ID0008: VIXIA HF M52 / VIXIA HF M50

4

Trademark Acknowledgements

• SD, SDHC and SDXC Logos are trademarks of SD-3C, LLC.

Microsoft and Windows are trademarks or registered trademarks of Microsoft Corporation in the United States

 

and/or other countries.

App Store, iPhone, iTunes, Mac OS and Macintosh are trademarks of Apple Inc., registered in the U.S. and

 

other countries.

“x.v.Color” and the “x.v.Color” logo are trademarks.

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of

 

HDMI Licensing LLC in the United States and other countries.

 

 

 

 

 

 

 

YouTube is a trademark of Google Inc.

Facebook is a registered trademark of Facebook, Inc.

COPY

Wi-Fi is a registered trademark of the Wi-Fi Alliance.

Wi-Fi Certified, WPA, WPA2, and the Wi-Fi Certified logo are trademarks of the Wi-Fi Alliance.

WPS as used on the camcorder's settings, onscreen displays and in this manual signifies Wi-Fi Protected

 

Setup.

DLNA, the DLNA Logo and DLNA CERTIFIED are trademarks, service marks, or certification marks of the Digital

 

Living Network Alliance.

Other names and products not mentioned above may be trademarks or registered trademarks of their

 

respective companies.

This device incorporates exFAT technology licensed from Microsoft.

“Full HD 1080” refers to Canon camcorders compliant with high-definition video

composed of 1,080 vertical pixels (scanning lines).

• ANY USE OF THIS PRODUCT OTHER THAN CONSUMER PERSONAL USE IN ANY MANNER

THAT COMPLIES WITH THE MPEG-2 STANDARD FOR ENCODING VIDEO INFORMATION FOR PACKAGED MEDIA IS EXPRESSLY PROHIBITED WITHOUT A LICENSE UNDER APPLICABLE PATENTS IN THE MPEG-2 PATENT PORTFOLIO, WHICH LICENSE IS AVAILABLE FROM MPEG LA, L.L.C., 250 STEELE STREET, SUITE 300, DENVER, COLORADO 80206.

• This product is licensed under AT&T patents for the MPEG-4 standard and may be used for encoding MPEG-4 compliant video and/or decoding MPEG-4 compliant video that was encoded only (1) for a personal and noncommercial purpose or (2) by a video provider licensed under the AT&T patents to provide MPEG-4 compliant video. No license is granted or implied for any other use for MPEG-4 standard.

5

Record movies in AVCHD and play them back on an HDTV in all their splendor. Alternatively, record movies in MP4 for uploading to the Web and transferring to mobile devices.
Audio Scene Select
(A114)
Optimize the audio settings of the built-in microphone by selecting the audio scene that matches your surroundings. Your audience will feel even more immersed in the scene during playback.

Exciting Features and New Functions

-/,

Wi-Fi Functions

(A163)

Enjoy the freedom of Wi-Fi functions by making your camcorder an active part of your Wi-Fi home network or by conveniently accessing Wi-Fi hotspots to upload your videos wherever you may be.

• You can save your recordings

Cinema-Look Filters

wirelessly to a computer in your

home network using the sup-

 

 

 

(A70)

plied software Network Utility

 

 

 

(A170). You can also send

Use professional cinema-look

your recordings wirelessly to an

filters to create unique movies

FTP server (A170), for exam-

with distinctive looks.

ple to send your videos from

 

 

 

your vacation spot to a network-

 

 

 

attached storage drive back

 

 

 

 

 

 

home.

COPY

• You can upload your recordings

AVCHD and MP4

wirelessly, directly from your

Recording (A31)

camcorder to YouTube and Facebook (A174).

• You can play back the recordings in your camcorder from DLNA-compatible TV sets and other DLNA media players connected to your home network (A178).

6

Smart AUTO (A47)

Smart AUTO automatically selects the best scene mode for the scene you want to shoot. You get spectacular recordings every time without worrying about settings.

Video Snapshot

Face Detection

(A71)

(A100)

Shoot or capture short scenes and arrange them into a video clip set to your favorite background music.

The camcorder automatically detects people’s faces and adjusts the focus and other settings accordingly for beautiful

 

 

 

results.

 

 

 

 

 

 

 

 

-/,

 

 

Image Stabilization

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Memory Save (A151)

 

 

 

 

 

 

 

 

 

 

COPY

 

 

 

 

 

Easily save the whole content of

 

Dynamic IS (A98)

the built-in memory or a memory

 

compensates for camcorder

card onto an external hard drive

 

shake when you shoot video

connected directly to the

 

while walking. Powered IS

camcorder. With no need for a

 

(A98) will produce stable shots

computer, this is a very

 

when you zoom in on distant

convenient way to save backup

 

subjects (full telephoto).

copies of your recordings.

 

Intelligent IS (A49) selects the

type of image stabilization for the recording situation.

7

Enjoying Your Recordings on Other Devices

Eye-Fi

Connect the camcorder to an HDTV (A142)

AVCHD

High Definition

Use an Eye-Fi card (A160) to wirelessly upload recordings to your computer or a video sharing Web site.

Upload your AVCHD movies* (A156) or MP4 movies

(A162) to the Web.

MP4

Upload MP4 movies to

your computer (A148). COPY

Save your recordings. You can also create discs from your recordings.*

Use the supplied PIXELA’s software (A146).

MPEG-2

Standard Definition

Upload AVCHD movies to your computer. -/,You can also choose to convert your AVCHD movies to standard definition files (A156) before uploading.

* -/,only.

8

-/,

Enjoying Your Recordings Using the Camcorder's Wi-Fi Functions

Play video wirelessly directly from the memory on AVCHDand DLNA-compatible HDTVs and other devices connected to the network (A178).

LAN cable

COPYJoin a Wi-Fi network by first

connecting to an access point (A165).

Transfer your recordings wirelessly from the camcorder to a computer or FTP server (A170).

Wirelessly connect to a Wi-Fi-enabled iOS

Upload your recordings wirelessly

device like an iPhone to upload your

to YouTube and Facebook

recordings (A175). Because you do not

(A174) to share your videos

need to be near your home network, you can

with friends and family.

even upload videos while traveling!

Upload your recordings to the Web.

 

9

Table of contents

Introduction

6 Exciting Features and New Functions

14 About this Manual

16Getting to Know the Camcorder

16Supplied Accessories and CD-ROMs

18Names of Parts

Preparations

21Getting Started

21

Charging the Battery Pack

24

COPY

Preparing the Accessories

26

Adjusting the LCD Screen

27 Basic Operation of the Camcorder

27

Using the Touch Screen

28

Using the Menus

31

Operating Modes

34

First Time Settings

34Setting the Date and Time

35Changing the Language

36Changing the Time Zone

37Using a Memory Card

37 Memory Cards Compatible for Use with the Camcorder

39Inserting and Removing a Memory Card

40-/,Selecting the Memory (Built-in Memory/

Memory Card) for the Recordings

40-/,Relay Recording

41Initializing the Memory

43 Using the Optional Wireless Controller

10 Table of contents

AUTO Mode

45

Basic Recording

45

Shooting Video and Taking Photos in AUTO Mode

47

About the Smart AUTO function

49Intelligent IS

50Zooming

52Quick Start

Video

54Basic Playback

54Playing Back Video

583D Flip View

59The [Index Selection] Screen: Selecting the Content to Play Back

60Deleting Scenes and Stories

64 Selecting the Playback Starting Point

70CinemaCOPYMode and Cinema-Look Filters

71Video Snapshot

72Decoration: Adding a Personal Touch

78Playing Back Stories from the Gallery

80Rating Scenes

82Playback with Background Music

86Copying and Moving Scenes Within/Between Stories

87Selecting a Story’s Thumbnail Image

87Changing a Story’s Title66 Onscreen Displays and Data Code

89 Advanced Functions

89 Recording in Manual Mode

91 Selecting the Video Quality (Recording Mode)

94Selecting the Frame Rate

95Special Scene Recording Programs

98Advanced Image Stabilization

98Powered IS

99Pre-Recording

100Face Detection

Table of contents 11

102Touch & Track

103Faders

104Manually Setting the Shutter Speed or Aperture

106Manual Exposure Adjustment

107Automatic Gain Control (AGC) Limit

108Manual Focus Adjustment

109Tele Macro

110White Balance

112Image Effects

113Self Timer

114Audio Scenes and Other Audio Settings

118Audio Recording Level

120Using Headphones

122Using the Mini Advanced Shoe

123Using an External Microphone

126Using an External Video Light

126Audio Mix

127Capturing Video Snapshot Scenes and Photos from a Movie

130Dividing ScenesCOPY

Photos

132Viewing Photos

136Slideshow

External Connections

138Terminals on the Camcorder

139Connection Diagrams

142Playback on a TV Screen

143Saving and Sharing Your Recordings

143-/,Copying Movies and Photos to a Memory Card

146 Saving Recordings on a Computer

151 -/,Memory Save: Saving an Entire Memory onto an External Hard Drive

155 Copying Recordings to an External Video Recorder

12 Table of contents

156-/,Uploading AVCHD Movies to the Web

162Uploading MP4 Movies and Photos to the Web

-/,Wi-Fi Functions

163Introduction to Wi-Fi

165 Connecting to a Wi-Fi Network

170Transferring Files to a Computer or FTP server

174Uploading Recordings to YouTube and Facebook

175Uploading Videos Using an iOS Device

178Wireless Playback on a DLNA-Compatible Device

Additional Information

182Appendix: Menu Options Lists

182 [Main Functions] Panel

186 [Other Settings] Menus

198 Appendix: Onscreen Icons and Displays

203

COPY

Trouble?

203

Troubleshooting

211

List of Messages

222

Do’s and Don’ts

222

Handling Precautions

227

Maintenance/Others

228

Using the Camcorder Abroad

229 General Information

229Accessories

230Optional Accessories

236

Specifications

240

Index

Table of contents 13

About this Manual

Thank you for purchasing the Canon VIXIA HF M52 / VIXIA HF M50 / VIXIA HF M500. Please read this manual carefully before you use the camcorder and retain it for future reference. Should your camcorder fail to operate correctly, refer to Troubleshooting (A203).

Conventions Used in this Manual

IMPORTANT: Precautions related to the camcorder’s operation.

NOTES: Additional topics that complement the basic operating procedures.

POINTS TO CHECK: Restrictions or requirements regarding the function described.

A: Reference page number within this manual.

-: Text that applies only to the models shown in the icon.

The following terms are used in this manual:

When not specified as “memory card” or “built-in memory”, the term “memory” by itself refers to both.

“Scene” refers to one movie unit from the point you press the

The photos included in thisCOPYmanual are simulated pictures taken with a still camera. Unless indicated otherwise, illustrations and menu icons refer to the -.Y

14 Introduction

indicates that a function is available in the operating mode indicated and indicates that the function is not available. The operating mode icons are divided into three groups: the first three icons represent the camera mode, the second three icons represent the recording standard, and the last two represent playback modes. For a detailed explanation refer to

Operating Modes (A31).

Brackets [ ] are used to refer to control buttons and menu options you will touch on the screen and to other onscreen messages and displays.

Self Timer

Operating modes:

*

* For movies only.

1 Press .

2 Activate the self timer.

[ Other Settings] >r>[Self Timer] >

[iOn <] >[X]

< will appear on the screen.

Repeat, selecting [jOff], to turn off the self timer.

Movies: In record pause mode, press

.

The camcorder starts recording after a 10-second countdown. The

countdown appears on the screen.

 

The names of physical buttons

The >arrow is used to abbreviate menu selections.

and switches on the

For a detailed explanation on how to use the menus,

camcorder are indicated COPYwithin refer to Using the Menus (A28). For a concise

a “button” frame.

summary of all available menu options and settings,

For example Y.

refer to the appendix Menu Options Lists (A182).

Introduction 15

Supplied Accessories and CD-ROMs

The following accessories are supplied with the camcorder:

XCA-110 Compact Power Adapter*

BP-718 Battery PackW

XIFC-300PCU/S USB Cable

HTC-100/S HDMI CableW

XQuick Guide

XWi-Fi Basic Setup Guide**

* CA-110E including power cord,COPYin Asia. Stylus enW ** -/,only.

16 Introduction

The following CD-ROMs and software are supplied with the camcorder:

PIXELA CD-ROM

--/,You can use VideoBrowser for managing, editing, and playing back AVCHD movies, and Network Utility when transferring recordings wirelessly to a computer.

-.Use Transfer Utility for saving and transferring AVCHD movies and music files you can use as background music.

-A printed Startup Guide for PIXELA's software is also supplied. Refer to this Startup Guide for details about the supplied software.

Canon VIXIA CD-ROM. Contains the following components.

-Instruction Manual - The full-version instruction manual of the camcorder (this PDF file).

-ImageBrowser EX - This CD-ROM contains an automatic installer for the supplied software ImageBrowser EX, which allows you to save and manage MP4 movies and photos; and upload MP4 movies to CANON iMAGE GATEWAY**, YouTube and Facebook. This CD-ROM contains an automatic installer for the supplied software ImageBrowser EX, which allows you to save and manage MP4 movies

and photos, and share MP4 movies. An Internet connection is required for installation.COPY

-Music data - Music files that can be used as background music during playback. These music files are for exclusive use with the supplied PIXELA’s software. The disc cannot be played back on CD players.

-Image mix data - Image files that can be used with the image mix function (image mix frames).

* The CD-ROM includes the instruction manual of the software (on PDF file).

**CANON iMAGE GATEWAY is an online service that allows you to share movies and photos, make photo albums, and more. This service may not be available in all countries/regions.

Introduction 17

Names of Parts

Left side view

Right side view

1VIDEO SNAP (video snapshot) button (A71)

2 HOME (home) button (A28)

3 U(camera/play) button (A33)

4 BATTERY RELEASE switch (A22)

5 USB terminal (A138, 140, 151, 155)

6 HDMI OUT terminal (A138, 139)

7AV OUT terminal (A138, 140)/ ×(headphones) terminal (A120)

8 MIC terminal (A124)

9 START/STOP button (A45)

Aq Wi-Fi antenna (-/,only)

9

Aq

 

 

 

Aa Strap mount (A24)

 

 

As Grip belt (A24)

Aa As

 

Ad Memory card slot (A39)

 

 

 

COPY

 

 

Af Stereo microphone (A118, 126)

 

 

Ag Remote sensor (A43)

 

Ad

Ah Instant AF sensor (A187)

Front view

Af Ag Af Ah

18 Introduction

Top view

LCD panel

 

jA Speaker (A56)

 

kA Zoom lever (A50)

 

lA Mini advanced shoe (A122)

lA

qS ACCESS (access) indicator (A45)

aS POWER button

 

 

sS ON/OFF (CHG) (charge) indicator:

Aj kA Sq

Green – On

 

Orange – Standby (A52)

 

Red – Charging (A21)

 

dS LCD touch screen (A26, 27)

Sa Ss

dS

COPY

Introduction 19

Back view

 

fS DC IN terminal (A21)

 

gS Battery attachment unit (A21)

 

 

 

Sf

 

hS Serial number

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sg

jS Tripod socket (A223)

Bottom view

Sh Sj

COPY

20 Introduction

Preparations

This chapter describes basic operations, such as using the touch panel, navigating the menus, and first time settings to help you learn more about your camcorder.

Getting Started

Charging the Battery Pack

The camcorder can be powered with a battery pack or directly using the compact power adapter.

For approximate charging times and recording/playback times with a fully charged battery pack, refer to Charging, Recording and Playback Times (A231).

1 Plug the power cord into a

 

 

power outlet.

COPY

 

 

 

 

For Asia only: Connect the power

 

 

cord to the compact power

 

 

adapter before plugging the

 

power cord into the power outlet.

 

 

2 Connect the compact power

 

 

adapter to the camcorder’s DC

 

 

IN terminal.

 

 

 

3Attach the battery pack to the camcorder.

Press the battery pack softly into the battery attachment unit and slide it up until it clicks in place.

DC IN terminal

For Asia only:

Preparations 21

ON/OFF (CHG) (charge) indicator

4 Charging will start when the

camcorder is turned off.

• If the camcorder was on, the green ON/OFF (CHG) indicator

will go out when you turn off the camcorder. After a moment, the ON/OFF (CHG) indicator will turn on in red (battery pack charging). The red ON/OFF

(CHG) indicator will go out when the battery pack is fully

charged.

• If the indicator flashes, refer to Troubleshooting (A207).

To remove the battery pack

1

Slide din the

 

direction of the arrow and hold it

 

pressed down.

COPY

2

 

Slide the battery pack and

then pull it out.

BATTERY RELEASE switch

IMPORTANT

Turn off the camcorder before connecting or disconnecting the compact power adapter. After pressing Pto turn off the camcorder, important data is updated in the memory. Be sure to wait until the green ON/OFF (CHG) indicator goes out.

Do not connect to the camcorder’s DC IN terminal or to the compact power adapter any electrical equipment that is not expressly recommended for use with this camcorder.

22 Preparations

To prevent equipment breakdowns and excessive heating, do not connect the supplied compact power adapter to voltage converters for overseas travels or special power sources such as those on aircraft and ships, DC-AC inverters, etc.

NOTES

We recommend charging the battery pack in temperatures between 10 °C and 30 °C (50 °F and 86 °F). If either the ambient temperature or the battery pack’s temperature is outside the range of approx. 0 °C to 40 °C (32 °F to 104 °F), charging will not start.

The battery pack will be charged only when the camcorder is off.

If the power supply was disconnected while charging a battery pack, make sure the ON/OFF (CHG) indicator has gone out before restoring the power supply.

If remaining battery time is an issue, you can power the camcorder using the compact power adapter so the battery pack will not be consumed.

Charged battery packs continue to discharge naturally. Therefore,

charge them on the day of use, or the day before, to ensure a full charge. COPY

The first time you use a battery pack, fully charge it and then use the camcorder until the battery pack is completely exhausted. Doing so will ensure that the remaining recording time will be displayed accurately.

We recommend that you prepare battery packs to last 2 to 3 times longer than you think you might need.

USA and Canada only: The Lithium ion/polymer battery that

powers the product is recyclable. Please call 1-800-8-BATTERY for information on how to recycle this battery.

Preparations 23

Canon 6093B004, HF M52, HF M50, HF M500, 6096B001 User Manual

Preparing the Accessories

Grip Belt and Straps

Fasten the grip belt.

Adjust the grip belt so that you can reach the zoom lever with your index finger, and the Y button with your thumb.

You can attach the supplied stylus pen to the grip belt.

To remove the grip belt

2 Pull the strap to removeCOPYit first from the front bracket on the camcorder, then to unthread it from the handgrip and finally to remove it from the rear bracket on the camcorder.

1 Lift the padded handgrip’s flap and detach the strap from the Velcro

pad.

24 Preparations

To attach an optional wrist strap

Attach the wrist strap to the rear bracket on the camcorder, adjust the length and fasten.

You can also attach the wrist strap to the strap mount on the grip belt to use both for extra convenience and protection.

To attach an optional shoulder strap

Pass the ends of the shoulder strap through the strap mount on the grip belt and adjust the length of the strap.

COPY

Preparations 25

Adjusting the LCD Screen

Rotating the LCD Panel

Open the LCD panel 90 degrees.

You can rotate the panel 90 degrees downward.

You can rotate the panel 180 degrees toward the lens. Rotating the LCD panel 180 degrees can be useful to allow the camcorder to include yourself in the picture when recording with the self timer.

180°

180°

 

90°

Subject can monitor the LCD screen

 

About the LCD screen: TheCOPYscreen is produced using extremely high-pre- cision manufacturing techniques, with more than 99.99% of the pixels operating to specification. Less than 0.01% of the pixels may occasionally misfire or appear as black, red, blue or green dots. This has no effect on the recorded image and does not constitute a malfunction.

For details about how to take care of the touch screen, refer to Handling Precautions (A222), Cleaning (A227).

You can adjust the screen's brightness using the q>[LCD Brightness] and [LCD Backlight] settings. When the compact power adapter is connected, [LCD Backlight] will automatically change to [H Bright].

26 Preparations

Basic Operation of the Camcorder

Using the Touch Screen

The control buttons and menu items that appear on the touch screen change dynamically depending on the operating mode and the task you are performing. With the intuitive touch screen interface you have all the controls at your fingertips. You can also use the supplied stylus pen for a more precise operation.

Touch

Press firmly on an element displayed on the touch screen.

Used to start playing back a scene in an index screen, to select a setting from the menus, to select the subject whom the camcorder will recognize as the main subject of the scene, etc.

Drag

While applying pressure, swipe your finger up and down or left and right across the

screen.

COPY

Used to scroll menus, to browse through index screen pages or to adjust slider controls like the volume.

IMPORTANT

The camcorder uses a pressure-sensitive touch screen. Press firmly when using touch operations.

In the following cases, you may not be able to perform touch operations correctly.

-Using your fingernails or hard-tipped objects other than the supplied stylus pen, such as ballpoint pens.

-Operating the touch screen with wet or gloved hands.

-Applying excessive force or forcefully scratching the touch screen.

-Attaching commercially available screen protectors or adhesive film onto the touch screen’s surface.

Preparations 27

Using the Menus

Many of the camcorder's functions can be adjusted from the [ Main Functions] panel and [ Other Settings] menus in the HOME menu. For details about the available menu options and settings, refer to the appendix Menu Options Lists (A182).

HOME Menu

Operating modes:

The HOME menu is the gateway to

 

most of the camcorder's functions

 

and settings. After you press

 

, the HOME menu will

 

appear and you can select from

 

the following control buttons. The

 

COPY

available control buttons depend

 

on whether the camcorder is in

 

recording or playback mode.

 

 

In playback mode

In recording mode

for -/,

[ Main Functions] - This contains functions commonly used while shooting, such as focus and exposure. Available only in recording mode.

[ Other Settings] - Selecting this control button will open up the [Other Settings] menus, which gives you access to settings such as the video quality (recording mode) and LCD brightness.

28 Preparations

[ Camera Mode] - From the [ Camera Mode] menu, you will be able to change whether you record movies in mode (camcorder

automatically takes care of many settings), mode (you can manually change settings), or mode (using the cinema-look filters, you can make movies with a cinematic feel). Available only in recording

mode. For details on how to set the camera mode, refer to Recording (A31).

[ Recording Standard] - This camcorder can record movies in either the AVCHD or MP4 recording standard. Use this menu to select the

standard that best suits your needs. You can also use Story Creator mode (A67) when choosing to record in AVCHD. Available only in

recording mode. For details on how to set the recording standard, refer to Recording (A31).

[ Wi-Fi] - -/,Allows you to access the various Wi-Fi functions this camcorder has to offer. Available only in playback mode. For more details on Wi-Fi functions, refer to Wi-Fi Functions (A163).

[GIndex Selection] - Use this to switch between the various index screens in playback mode (A59).

 

 

 

 

COPY

[Main Functions] Panel

Operating modes:

 

 

 

 

 

*

 

 

 

 

 

* In

 

mode, access to functions is limited.

The [ Main Functions] panel contains frequently used shooting functions. Press to open the HOME menu and then touch [ Main Functions] to open the panel. Alternatively, you can touch Fin the upper-left portion of the recording screen. Next, touch the function you want to set or adjust.

Preparations 29

 

 

In

mode

Touch to scroll up

 

 

 

 

Drag your finger up

 

 

 

 

 

 

 

 

 

and down along the

 

 

 

 

 

 

or down

 

 

 

 

scroll bar to display

 

 

 

 

 

 

 

 

 

 

 

 

the rest of the panel

 

 

 

Touch the control button of the desired function

You may need to drag your finger up and down along the scroll bar or touch [ ] and [ ] to find the control button of the desired function.

[Edit] Panel

Operating modes:

 

 

 

 

 

COPY

 

 

 

 

 

 

 

 

 

 

Touch [Edit] to display a panel showing available operations (copying,

deleting, etc.), and then touch the operation you want to perform.

 

 

 

 

 

In

mode

for -/,

Touch the control button of the desired operation

[Other Settings] Menus

Operating modes:

*

* In mode, access to functions is limited.

30 Preparations

Loading...
+ 216 hidden pages