PUB. DIE-0416-000B
HD Camcorder
Instruction Manual
COPY
- ,
Important Usage Instructions
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
COPYRIGHT WARNING:
Unauthorized recording of copyrighted materials may infringe on the rights of copyright owners and be contrary to copyright laws.
The Mains plug is used as the disconnect device. The Mains plug shall remain readily operable to disconnect the plug in case of an accident.
CAUTION:
•Danger of explosion if the wrong type of batteries are attached. Use only the same type of batteries.
•Do not expose batteries or product to excessive heat such as the inside of a car under direct sunlight, fire, etc.
While using the compact power adapter, do not wrap it or cover it with a piece of cloth, and do not place it in confined narrow spaces.
CAUTION:
COPYCAUTION
RISK F ELECTRIC SH CK
DO N T EN
TO REDUCE THE RISK OF ELE TRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVI EABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure, that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point, within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
2
FCC/IC NOTICE
HD Camcorder, VIXIA HF M52 / VIXIA HF M50 / VIXIA HF M500 systems
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and use in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules. Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If such changes or modifications should be made, you could be required to stop operation of the equipment.
Model ID0008 (including WLANCOPYModule Model WM217)
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
The available scientific evidence does not show that any health problems are associated with using low-power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low-power wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure to low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. This model has been tested and found to comply with FCC/IC radiation exposure limits set forth for an uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules.
Canon U.S.A., Inc.
One Canon Plaza, Lake Success, NY 11042, U.S.A.
Tel No. (516)328-5600
This Class B digital apparatus complies with Canadian ICES-003.
3
IMPORTANT SAFETY INSTRUCTIONS
In these safety instructions the word “apparatus” refers to the Canon HD Camcorder VIXIA HF M52 / VIXIA HF M50 / VIXIA HF M500 and all its accessories.
1 Read these instructions.
2 Keep these instructions.
3Heed all warnings.
4Follow all instructions.
5 Do not use this apparatus near water.
6Clean only with dry cloth.
7Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
8Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
9Only use attachments/accessories specified by the manufacturer.
10Unplug this apparatus during lightning storms or when unused for long periods of time.
11Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallenCOPYinto the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
REGIONS OF USE
VIXIA HF M52 and VIXIA HF M50 are in compliance (as of January 2012) with the radio signal regulations of the regions listed below. For details on other regions where they can be used, make inquiries with the contacts listed on the back side of this instruction manual.
REGIONS
Canada, Hong Kong S.A.R., USA
Model
ID0008: VIXIA HF M52 / VIXIA HF M50
4
Trademark Acknowledgements
• SD, SDHC and SDXC Logos are trademarks of SD-3C, LLC.
• |
Microsoft and Windows are trademarks or registered trademarks of Microsoft Corporation in the United States |
||
|
and/or other countries. |
||
• |
App Store, iPhone, iTunes, Mac OS and Macintosh are trademarks of Apple Inc., registered in the U.S. and |
||
|
other countries. |
||
• |
“x.v.Color” and the “x.v.Color” logo are trademarks. |
||
• |
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of |
||
|
HDMI Licensing LLC in the United States and other countries. |
||
|
|
|
|
|
|
|
|
• |
YouTube is a trademark of Google Inc. |
||
• |
Facebook is a registered trademark of Facebook, Inc. |
||
• |
COPY |
||
Wi-Fi is a registered trademark of the Wi-Fi Alliance. |
|||
• |
Wi-Fi Certified, WPA, WPA2, and the Wi-Fi Certified logo are trademarks of the Wi-Fi Alliance. |
||
• |
WPS as used on the camcorder's settings, onscreen displays and in this manual signifies Wi-Fi Protected |
||
|
Setup. |
||
• |
DLNA, the DLNA Logo and DLNA CERTIFIED are trademarks, service marks, or certification marks of the Digital |
||
|
Living Network Alliance. |
||
• |
Other names and products not mentioned above may be trademarks or registered trademarks of their |
||
|
respective companies. |
||
• |
This device incorporates exFAT technology licensed from Microsoft. |
||
• |
“Full HD 1080” refers to Canon camcorders compliant with high-definition video |
composed of 1,080 vertical pixels (scanning lines).
• ANY USE OF THIS PRODUCT OTHER THAN CONSUMER PERSONAL USE IN ANY MANNER
THAT COMPLIES WITH THE MPEG-2 STANDARD FOR ENCODING VIDEO INFORMATION FOR PACKAGED MEDIA IS EXPRESSLY PROHIBITED WITHOUT A LICENSE UNDER APPLICABLE PATENTS IN THE MPEG-2 PATENT PORTFOLIO, WHICH LICENSE IS AVAILABLE FROM MPEG LA, L.L.C., 250 STEELE STREET, SUITE 300, DENVER, COLORADO 80206.
• This product is licensed under AT&T patents for the MPEG-4 standard and may be used for encoding MPEG-4 compliant video and/or decoding MPEG-4 compliant video that was encoded only (1) for a personal and noncommercial purpose or (2) by a video provider licensed under the AT&T patents to provide MPEG-4 compliant video. No license is granted or implied for any other use for MPEG-4 standard.
5
Exciting Features and New Functions
-/,
Wi-Fi Functions
(A163)
Enjoy the freedom of Wi-Fi functions by making your camcorder an active part of your Wi-Fi home network or by conveniently accessing Wi-Fi hotspots to upload your videos wherever you may be.
• You can save your recordings |
Cinema-Look Filters |
||||
wirelessly to a computer in your |
|||||
home network using the sup- |
|
|
|
||
(A70) |
|||||
plied software Network Utility |
|||||
|
|
|
|||
(A170). You can also send |
Use professional cinema-look |
||||
your recordings wirelessly to an |
|||||
filters to create unique movies |
|||||
FTP server (A170), for exam- |
|||||
with distinctive looks. |
|||||
ple to send your videos from |
|||||
|
|
|
|||
your vacation spot to a network- |
|
|
|
||
attached storage drive back |
|
|
|
||
|
|
|
|||
home. |
COPY |
||||
• You can upload your recordings |
AVCHD and MP4 |
||||
wirelessly, directly from your |
Recording (A31) |
camcorder to YouTube and Facebook (A174).
• You can play back the recordings in your camcorder from DLNA-compatible TV sets and other DLNA media players connected to your home network (A178).
6
Smart AUTO (A47)
Smart AUTO automatically selects the best scene mode for the scene you want to shoot. You get spectacular recordings every time without worrying about settings.
Video Snapshot |
Face Detection |
(A71) |
(A100) |
Shoot or capture short scenes and arrange them into a video clip set to your favorite background music.
The camcorder automatically detects people’s faces and adjusts the focus and other settings accordingly for beautiful
|
|
|
results. |
||||
|
|
|
|
|
|
|
|
-/, |
|
|
Image Stabilization |
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
||
Memory Save (A151) |
|
|
|
||||
|
|
|
|
|
|
||
|
COPY |
|
|
||||
|
|
|
|||||
Easily save the whole content of |
|
Dynamic IS (A98) |
|||||
the built-in memory or a memory |
|
compensates for camcorder |
|||||
card onto an external hard drive |
|
shake when you shoot video |
|||||
connected directly to the |
|
while walking. Powered IS |
|||||
camcorder. With no need for a |
|
(A98) will produce stable shots |
|||||
computer, this is a very |
|
when you zoom in on distant |
|||||
convenient way to save backup |
|
subjects (full telephoto). |
|||||
copies of your recordings. |
|
Intelligent IS (A49) selects the |
type of image stabilization for the recording situation.
7
Enjoying Your Recordings on Other Devices
Eye-Fi
Connect the camcorder to an HDTV (A142)
AVCHD
High Definition
Use an Eye-Fi card (A160) to wirelessly upload recordings to your computer or a video sharing Web site.
Upload your AVCHD movies* (A156) or MP4 movies
(A162) to the Web.
MP4
Upload MP4 movies to
your computer (A148). COPY
Save your recordings. You can also create discs from your recordings.*
Use the supplied PIXELA’s software (A146).
MPEG-2
Standard Definition
Upload AVCHD movies to your computer. -/,You can also choose to convert your AVCHD movies to standard definition files (A156) before uploading.
* -/,only.
8
-/,
Enjoying Your Recordings Using the Camcorder's Wi-Fi Functions
Play video wirelessly directly from the memory on AVCHDand DLNA-compatible HDTVs and other devices connected to the network (A178).
LAN cable
COPYJoin a Wi-Fi network by first
connecting to an access point (A165).
Transfer your recordings wirelessly from the camcorder to a computer or FTP server (A170).
Wirelessly connect to a Wi-Fi-enabled iOS |
Upload your recordings wirelessly |
device like an iPhone to upload your |
to YouTube and Facebook |
recordings (A175). Because you do not |
(A174) to share your videos |
need to be near your home network, you can |
with friends and family. |
even upload videos while traveling! |
Upload your recordings to the Web. |
|
9
Table of contents
Introduction
6 Exciting Features and New Functions
14 About this Manual
16Getting to Know the Camcorder
16Supplied Accessories and CD-ROMs
18Names of Parts
Preparations
21Getting Started
21 |
Charging the Battery Pack |
24 |
COPY |
Preparing the Accessories |
|
26 |
Adjusting the LCD Screen |
27 Basic Operation of the Camcorder |
|
27 |
Using the Touch Screen |
28 |
Using the Menus |
31 |
Operating Modes |
34 |
First Time Settings |
34Setting the Date and Time
35Changing the Language
36Changing the Time Zone
37Using a Memory Card
37 Memory Cards Compatible for Use with the Camcorder
39Inserting and Removing a Memory Card
40-/,Selecting the Memory (Built-in Memory/
Memory Card) for the Recordings
40-/,Relay Recording
41Initializing the Memory
43 Using the Optional Wireless Controller
10 Table of contents
AUTO Mode
45 |
Basic Recording |
45 |
Shooting Video and Taking Photos in AUTO Mode |
47 |
About the Smart AUTO function |
49Intelligent IS
50Zooming
52Quick Start
Video
54Basic Playback
54Playing Back Video
583D Flip View
59The [Index Selection] Screen: Selecting the Content to Play Back
60Deleting Scenes and Stories
64 Selecting the Playback Starting Point
70CinemaCOPYMode and Cinema-Look Filters
71Video Snapshot
72Decoration: Adding a Personal Touch
78Playing Back Stories from the Gallery
80Rating Scenes
82Playback with Background Music
86Copying and Moving Scenes Within/Between Stories
87Selecting a Story’s Thumbnail Image
87Changing a Story’s Title66 Onscreen Displays and Data Code
89 Advanced Functions
89 Recording in Manual Mode
91 Selecting the Video Quality (Recording Mode)
94Selecting the Frame Rate
95Special Scene Recording Programs
98Advanced Image Stabilization
98Powered IS
99Pre-Recording
100Face Detection
Table of contents 11
102Touch & Track
103Faders
104Manually Setting the Shutter Speed or Aperture
106Manual Exposure Adjustment
107Automatic Gain Control (AGC) Limit
108Manual Focus Adjustment
109Tele Macro
110White Balance
112Image Effects
113Self Timer
114Audio Scenes and Other Audio Settings
118Audio Recording Level
120Using Headphones
122Using the Mini Advanced Shoe
123Using an External Microphone
126Using an External Video Light
126Audio Mix
127Capturing Video Snapshot Scenes and Photos from a Movie
130Dividing ScenesCOPY
Photos
132Viewing Photos
136Slideshow
External Connections
138Terminals on the Camcorder
139Connection Diagrams
142Playback on a TV Screen
143Saving and Sharing Your Recordings
143-/,Copying Movies and Photos to a Memory Card
146 Saving Recordings on a Computer
151 -/,Memory Save: Saving an Entire Memory onto an External Hard Drive
155 Copying Recordings to an External Video Recorder
12 Table of contents
156-/,Uploading AVCHD Movies to the Web
162Uploading MP4 Movies and Photos to the Web
-/,Wi-Fi Functions
163Introduction to Wi-Fi
165 Connecting to a Wi-Fi Network
170Transferring Files to a Computer or FTP server
174Uploading Recordings to YouTube and Facebook
175Uploading Videos Using an iOS Device
178Wireless Playback on a DLNA-Compatible Device
Additional Information
182Appendix: Menu Options Lists
182 [Main Functions] Panel
186 [Other Settings] Menus
198 Appendix: Onscreen Icons and Displays |
|
203 |
COPY |
Trouble? |
|
203 |
Troubleshooting |
211 |
List of Messages |
222 |
Do’s and Don’ts |
222 |
Handling Precautions |
227 |
Maintenance/Others |
228 |
Using the Camcorder Abroad |
229 General Information
229Accessories
230Optional Accessories
236 |
Specifications |
240 |
Index |
Table of contents 13
About this Manual
Thank you for purchasing the Canon VIXIA HF M52 / VIXIA HF M50 / VIXIA HF M500. Please read this manual carefully before you use the camcorder and retain it for future reference. Should your camcorder fail to operate correctly, refer to Troubleshooting (A203).
Conventions Used in this Manual
• IMPORTANT: Precautions related to the camcorder’s operation.
• NOTES: Additional topics that complement the basic operating procedures.
• POINTS TO CHECK: Restrictions or requirements regarding the function described.
•A: Reference page number within this manual.
•-: Text that applies only to the models shown in the icon.
•The following terms are used in this manual:
When not specified as “memory card” or “built-in memory”, the term “memory” by itself refers to both.
“Scene” refers to one movie unit from the point you press the
•The photos included in thisCOPYmanual are simulated pictures taken with a still camera. Unless indicated otherwise, illustrations and menu icons refer to the -.Y
14 Introduction
indicates that a function is available in the operating mode indicated and indicates that the function is not available. The operating mode icons are divided into three groups: the first three icons represent the camera mode, the second three icons represent the recording standard, and the last two represent playback modes. For a detailed explanation refer to
Operating Modes (A31).
Brackets [ ] are used to refer to control buttons and menu options you will touch on the screen and to other onscreen messages and displays.
Self Timer
Operating modes:
*
* For movies only.
1 Press .
2 Activate the self timer.
[ Other Settings] >r>[Self Timer] >
[iOn <] >[X]
•< will appear on the screen.
•Repeat, selecting [jOff], to turn off the self timer.
Movies: In record pause mode, press |
. |
|
The camcorder starts recording after a 10-second countdown. The |
||
countdown appears on the screen. |
|
|
The names of physical buttons |
The >arrow is used to abbreviate menu selections. |
|
and switches on the |
For a detailed explanation on how to use the menus, |
|
camcorder are indicated COPYwithin refer to Using the Menus (A28). For a concise |
||
a “button” frame. |
summary of all available menu options and settings, |
|
For example Y. |
refer to the appendix Menu Options Lists (A182). |
Introduction 15
Supplied Accessories and CD-ROMs
The following accessories are supplied with the camcorder:
XCA-110 Compact Power Adapter*
BP-718 Battery PackW
XIFC-300PCU/S USB Cable
HTC-100/S HDMI CableW
XQuick Guide
XWi-Fi Basic Setup Guide**
* CA-110E including power cord,COPYin Asia. Stylus enW ** -/,only.
16 Introduction
The following CD-ROMs and software are supplied with the camcorder:
•PIXELA CD-ROM
--/,You can use VideoBrowser for managing, editing, and playing back AVCHD movies, and Network Utility when transferring recordings wirelessly to a computer.
-.Use Transfer Utility for saving and transferring AVCHD movies and music files you can use as background music.
-A printed Startup Guide for PIXELA's software is also supplied. Refer to this Startup Guide for details about the supplied software.
•Canon VIXIA CD-ROM. Contains the following components.
-Instruction Manual - The full-version instruction manual of the camcorder (this PDF file).
-ImageBrowser EX - This CD-ROM contains an automatic installer for the supplied software ImageBrowser EX, which allows you to save and manage MP4 movies and photos; and upload MP4 movies to CANON iMAGE GATEWAY**, YouTube and Facebook. This CD-ROM contains an automatic installer for the supplied software ImageBrowser EX, which allows you to save and manage MP4 movies
and photos, and share MP4 movies. An Internet connection is required for installation.COPY
-Music data - Music files that can be used as background music during playback. These music files are for exclusive use with the supplied PIXELA’s software. The disc cannot be played back on CD players.
-Image mix data - Image files that can be used with the image mix function (image mix frames).
* The CD-ROM includes the instruction manual of the software (on PDF file).
**CANON iMAGE GATEWAY is an online service that allows you to share movies and photos, make photo albums, and more. This service may not be available in all countries/regions.
Introduction 17
Names of Parts
Left side view
Right side view
1VIDEO SNAP (video snapshot) button (A71)
2 HOME (home) button (A28)
3 U(camera/play) button (A33)
4 BATTERY RELEASE switch (A22)
5 USB terminal (A138, 140, 151, 155)
6 HDMI OUT terminal (A138, 139)
7AV OUT terminal (A138, 140)/ ×(headphones) terminal (A120)
8 MIC terminal (A124)
9 START/STOP button (A45)
Aq Wi-Fi antenna (-/,only)
9 |
Aq |
|
|
|
Aa Strap mount (A24) |
|
|
As Grip belt (A24) |
Aa As |
|
Ad Memory card slot (A39) |
|
|
|
|
COPY |
|
|
|
Af Stereo microphone (A118, 126) |
|
|
Ag Remote sensor (A43) |
|
Ad |
Ah Instant AF sensor (A187) |
Front view
Af Ag Af Ah
18 Introduction
Top view
LCD panel
|
jA Speaker (A56) |
|
|
kA Zoom lever (A50) |
|
|
lA Mini advanced shoe (A122) |
|
lA |
qS ACCESS (access) indicator (A45) |
|
aS POWER button |
||
|
||
|
sS ON/OFF (CHG) (charge) indicator: |
|
Aj kA Sq |
Green – On |
|
|
Orange – Standby (A52) |
|
|
Red – Charging (A21) |
|
|
dS LCD touch screen (A26, 27) |
Sa Ss
dS |
COPY |
Introduction 19
Back view |
|
fS DC IN terminal (A21) |
|
|
gS Battery attachment unit (A21) |
||
|
|
|
|
Sf |
|
hS Serial number |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Sg
jS Tripod socket (A223)
Bottom view
Sh Sj
COPY
20 Introduction
Preparations
This chapter describes basic operations, such as using the touch panel, navigating the menus, and first time settings to help you learn more about your camcorder.
Getting Started
Charging the Battery Pack
The camcorder can be powered with a battery pack or directly using the compact power adapter.
For approximate charging times and recording/playback times with a fully charged battery pack, refer to Charging, Recording and Playback Times (A231).
1 Plug the power cord into a |
|
|
|
power outlet. |
COPY |
|
|
|
|
|
|
For Asia only: Connect the power |
|
|
|
cord to the compact power |
|
|
|
adapter before plugging the |
|
||
power cord into the power outlet. |
|
|
|
2 Connect the compact power |
|
|
|
adapter to the camcorder’s DC |
|
|
|
IN terminal. |
|
|
|
3Attach the battery pack to the camcorder.
Press the battery pack softly into the battery attachment unit and slide it up until it clicks in place.
DC IN terminal
For Asia only:
Preparations 21
ON/OFF (CHG) (charge) indicator
4 Charging will start when the
camcorder is turned off.
• If the camcorder was on, the green ON/OFF (CHG) indicator
will go out when you turn off the camcorder. After a moment, the ON/OFF (CHG) indicator will turn on in red (battery pack charging). The red ON/OFF
(CHG) indicator will go out when the battery pack is fully
charged.
• If the indicator flashes, refer to Troubleshooting (A207).
To remove the battery pack
1 |
Slide din the |
|
|
direction of the arrow and hold it |
|
|
pressed down. |
COPY |
2 |
|
|
Slide the battery pack and |
then pull it out.
BATTERY RELEASE switch
IMPORTANT
•Turn off the camcorder before connecting or disconnecting the compact power adapter. After pressing Pto turn off the camcorder, important data is updated in the memory. Be sure to wait until the green ON/OFF (CHG) indicator goes out.
•Do not connect to the camcorder’s DC IN terminal or to the compact power adapter any electrical equipment that is not expressly recommended for use with this camcorder.
22 Preparations
•To prevent equipment breakdowns and excessive heating, do not connect the supplied compact power adapter to voltage converters for overseas travels or special power sources such as those on aircraft and ships, DC-AC inverters, etc.
NOTES
•We recommend charging the battery pack in temperatures between 10 °C and 30 °C (50 °F and 86 °F). If either the ambient temperature or the battery pack’s temperature is outside the range of approx. 0 °C to 40 °C (32 °F to 104 °F), charging will not start.
•The battery pack will be charged only when the camcorder is off.
•If the power supply was disconnected while charging a battery pack, make sure the ON/OFF (CHG) indicator has gone out before restoring the power supply.
•If remaining battery time is an issue, you can power the camcorder using the compact power adapter so the battery pack will not be consumed.
•Charged battery packs continue to discharge naturally. Therefore,
charge them on the day of use, or the day before, to ensure a full charge. COPY
•The first time you use a battery pack, fully charge it and then use the camcorder until the battery pack is completely exhausted. Doing so will ensure that the remaining recording time will be displayed accurately.
•We recommend that you prepare battery packs to last 2 to 3 times longer than you think you might need.
•USA and Canada only: The Lithium ion/polymer battery that
powers the product is recyclable. Please call 1-800-8-BATTERY for information on how to recycle this battery.
Preparations 23
Preparing the Accessories
Grip Belt and Straps
Fasten the grip belt.
Adjust the grip belt so that you can reach the zoom lever with your index finger, and the Y button with your thumb.
You can attach the supplied stylus pen to the grip belt.
To remove the grip belt
2 Pull the strap to removeCOPYit first from the front bracket on the camcorder, then to unthread it from the handgrip and finally to remove it from the rear bracket on the camcorder.
1 Lift the padded handgrip’s flap and detach the strap from the Velcro
pad.
24 Preparations
To attach an optional wrist strap
Attach the wrist strap to the rear bracket on the camcorder, adjust the length and fasten.
You can also attach the wrist strap to the strap mount on the grip belt to use both for extra convenience and protection.
To attach an optional shoulder strap
Pass the ends of the shoulder strap through the strap mount on the grip belt and adjust the length of the strap.
COPY |
Preparations 25
Adjusting the LCD Screen
Rotating the LCD Panel
Open the LCD panel 90 degrees.
•You can rotate the panel 90 degrees downward.
•You can rotate the panel 180 degrees toward the lens. Rotating the LCD panel 180 degrees can be useful to allow the camcorder to include yourself in the picture when recording with the self timer.
180° |
180° |
|
90° |
Subject can monitor the LCD screen |
|
•About the LCD screen: TheCOPYscreen is produced using extremely high-pre- cision manufacturing techniques, with more than 99.99% of the pixels operating to specification. Less than 0.01% of the pixels may occasionally misfire or appear as black, red, blue or green dots. This has no effect on the recorded image and does not constitute a malfunction.
•For details about how to take care of the touch screen, refer to Handling Precautions (A222), Cleaning (A227).
•You can adjust the screen's brightness using the q>[LCD Brightness] and [LCD Backlight] settings. When the compact power adapter is connected, [LCD Backlight] will automatically change to [H Bright].
26 Preparations
Basic Operation of the Camcorder
Using the Touch Screen
The control buttons and menu items that appear on the touch screen change dynamically depending on the operating mode and the task you are performing. With the intuitive touch screen interface you have all the controls at your fingertips. You can also use the supplied stylus pen for a more precise operation.
Touch
Press firmly on an element displayed on the touch screen.
Used to start playing back a scene in an index screen, to select a setting from the menus, to select the subject whom the camcorder will recognize as the main subject of the scene, etc.
Drag
While applying pressure, swipe your finger up and down or left and right across the
screen.
COPY
Used to scroll menus, to browse through index screen pages or to adjust slider controls like the volume.
IMPORTANT
•The camcorder uses a pressure-sensitive touch screen. Press firmly when using touch operations.
•In the following cases, you may not be able to perform touch operations correctly.
-Using your fingernails or hard-tipped objects other than the supplied stylus pen, such as ballpoint pens.
-Operating the touch screen with wet or gloved hands.
-Applying excessive force or forcefully scratching the touch screen.
-Attaching commercially available screen protectors or adhesive film onto the touch screen’s surface.
Preparations 27
Using the Menus
Many of the camcorder's functions can be adjusted from the [ Main Functions] panel and [ Other Settings] menus in the HOME menu. For details about the available menu options and settings, refer to the appendix Menu Options Lists (A182).
HOME Menu
Operating modes:
The HOME menu is the gateway to |
|
most of the camcorder's functions |
|
and settings. After you press |
|
, the HOME menu will |
|
appear and you can select from |
|
the following control buttons. The |
|
COPY |
|
available control buttons depend |
|
on whether the camcorder is in |
|
recording or playback mode. |
|
|
In playback mode |
In recording mode |
for -/, |
•[ Main Functions] - This contains functions commonly used while shooting, such as focus and exposure. Available only in recording mode.
•[ Other Settings] - Selecting this control button will open up the [Other Settings] menus, which gives you access to settings such as the video quality (recording mode) and LCD brightness.
28 Preparations
•[ Camera Mode] - From the [ Camera Mode] menu, you will be able to change whether you record movies in mode (camcorder
automatically takes care of many settings), mode (you can manually change settings), or mode (using the cinema-look filters, you can make movies with a cinematic feel). Available only in recording
mode. For details on how to set the camera mode, refer to Recording (A31).
•[ Recording Standard] - This camcorder can record movies in either the AVCHD or MP4 recording standard. Use this menu to select the
standard that best suits your needs. You can also use Story Creator mode (A67) when choosing to record in AVCHD. Available only in
recording mode. For details on how to set the recording standard, refer to Recording (A31).
•[ Wi-Fi] - -/,Allows you to access the various Wi-Fi functions this camcorder has to offer. Available only in playback mode. For more details on Wi-Fi functions, refer to Wi-Fi Functions (A163).
•[GIndex Selection] - Use this to switch between the various index screens in playback mode (A59).
|
|
|
|
COPY |
||
[Main Functions] Panel |
||||||
Operating modes: |
|
|
|
|
||
|
* |
|
|
|
|
|
* In |
|
mode, access to functions is limited. |
The [ Main Functions] panel contains frequently used shooting functions. Press to open the HOME menu and then touch [ Main Functions] to open the panel. Alternatively, you can touch Fin the upper-left portion of the recording screen. Next, touch the function you want to set or adjust.
Preparations 29
|
|
In |
mode |
|||
Touch to scroll up |
|
|
|
|
Drag your finger up |
|
|
|
|
|
|||
|
||||||
|
|
|
|
and down along the |
||
|
|
|
|
|
|
|
or down |
|
|
|
|
scroll bar to display |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
the rest of the panel |
|
|
|
Touch the control button of the desired function
You may need to drag your finger up and down along the scroll bar or touch [ ] and [ ] to find the control button of the desired function.
[Edit] Panel
Operating modes:
|
|
|
|
|
COPY |
|
|
|
|
|
|||||||
|
|
|
|
|
|
|||
Touch [Edit] to display a panel showing available operations (copying, |
||||||||
deleting, etc.), and then touch the operation you want to perform. |
||||||||
|
|
|
|
|
In |
mode |
for -/,
Touch the control button of the desired operation
[Other Settings] Menus
Operating modes:
*
* In mode, access to functions is limited.
30 Preparations