Start Here
Easy Setup Instructions
|
Unpack the Machine |
• Please confi rm the included items against the illustration printed on the lid of the packing box. |
|
|
|
|
|||
|
• A USB cable is necessary to connect the machine with your computer. |
|
|
|
|
|
|
||
QT5-0786-V01 |
|
2 Install the Print Head |
3 Install the Ink Tanks |
|
1 Prepare the Machine |
aPlace the machine on a fl at and horizontal surface, and do not place any objects in front of the machine. Open the Sheet Feeder Cover and pull the Paper Support, then the Paper Output Tray and open the Output Tray Extension.
Caution
Before turning on the machine, remove all of the shipping tapes.
Important
Do not connect the USB cable until after the software is installed.
Note
To open the Paper Output Tray, put your fi nger in the rounded indent of the tray and open it gently.
bUnlock the Scanning Unit (Printer
Cover).
(1)Open the Document Cover.
(2)Move the Scanner Lock Switch towards the release mark to unlock the Scanning Unit (Printer
Cover).
Caution
●Make sure to unlock the Scanning Unit (Printer Cover) before turning the machine on.
●Before transporting the machine, always lock the Scanning Unit (Printer Cover) by moving the Scanner Lock Switch towards the lock mark.
(2)(1)
Scanning Unit (Printer Cover)
cPlug the power cord in the back of the machine and connect the other end to the wall outlet.
Important
Make sure that the Document Cover is closed.
dOpen the Operation Panel, then press the ON/OFF button to turn on the machine.
eUse the { or } button on the |
aRemove the Print Head from its |
aPeel back the orange tab completely |
Operation Panel to select the language |
package. |
and remove the plastic wrapper from |
for the LCD, then press the OK button. |
|
the ink tank. |
(1)Press the { or } button to select the language.
(2)Press the OK
button.
Important
If an unintended language is displayed on the LCD, press the Back button to return to the Language selection screen.
Once the message “Install the print head and set the ink tank.” appears, go to f.
fOpen the Scanning Unit (Printer Cover) until it locks into place. The Print Head Holder moves to the center.
Important
●For your safety, always firmly grip the areas illustrated when opening the Scanning Unit (Printer Cover).
●If the Document Cover is opened, you cannot open the Scanner Unit (Printer Cover). Be sure to open the Scanner Unit (Printer Cover) and the Document Cover at the same time.
gOpen the Inner Cover. Write down the serial number located inside the machine. You will need this to register your product.
Inner Cover Serial Number Location
Caution
There may be some transparent or light blue ink on the inside of the bag the print head comes in, or the inside of the protective cap - this has no effect on print quality. Be careful not to get ink on yourself when handling these items.
bRemove the orange protective cap from the Print Head and discard it.
Electrical Contacts
Protective Cap |
Print Head Nozzles |
Note
Do not touch the print head nozzles and the electrical contacts.
cFirmly raise the Print Head Lock Lever until it stops.The Print Head Lock Lever may feel heavy.
dInsert the Print Head.
Do not touch!
ePush the Print Head to hold it in place, and lower the Print Head Lock Lever.
Important
If the Scanning Unit (Printer Cover) is left open for more than 10 minutes, the Print Head Holder moves to the right. Close and reopen the Scanning Unit (Printer Cover) to return the Holder to the center.
If the orange-colored protective fi lm is not removed completely, problems with printing may occur.
bTwist off and discard the orange protective cap located on the bottom of the ink tank.
Protective Cap
Do not press!
Ink Port
Electrical Contacts
Important
•Do not touch the electrical contacts.
•Do not touch the ink port.
cInsert the ink tank into the right-hand slot and press the mark on the ink tank until it clicks into place.
dMake sure the ink lamp lights red.
Refer to the color guide on the Print Head Lock Lever.
eClose the Inner Cover and the
Scanning Unit (Printer Cover).
Important
•For your safety, always firmly grip the areas illustrated when closing the Scanning Unit (Printer Cover).
•The machine starts operating. Wait about 2 minutes until the machine stops making noise.
Offi ce All-In-One
4 Align the Print Head
aPinch the Paper Guide and slide it to the left end.
Paper Support
Extension
Paper Guide
Hardware setup and Print Head alignment is complete.
bLoad two sheets of supplied paper (MP-101) into the Auto Sheet Feeder with the printing side (whiter side) facing up, align the paper with the right side of the Cover Guide, then slide the Paper Guide against the paper stack.
Paper Guide |
Print Side |
Cover Guide
cMake sure that Yes is selected in the message requesting head alignment, then press the OK button.
Note
Print Head alignment takes about 14 minutes to complete. Do not start another operation here.
The pattern is printed. And Print Head is aligned automatically.
OK
Note
•The pattern is printed in black and blue.
•When Automatic Print Head Alignment cannot be executed correctly, the message “Auto head align has failed.” is displayed on the LCD. Refer to “Error
Message is Displayed on the LCD” in the User’s Guide on-screen manual.
Easy-Scroll Wheel
Turn the Easy-Scroll Wheel left or right to easily select
a menu or a setting item.
For details, refer to “Basic
Operation for the Operation
Panel” in the Quick Start
Guide.
* You can also use the {, }, [, or ] button to select.
Cassette
For information on how to load paper in the Cassette, refer to “Loading Paper in the Cassette” in “Loading Printing Paper” of the
Quick Start Guide.