f-5.6L
EF70-300mm f/4-5.6L IS USM
Instruction
ENG
COPY
ENG-1
Dedicated to EOS cameras, the Canon EF70300mm f/4-5.6L IS USM lens is a highperformance telephoto zoom lens equipped
with an Image Stabilizer.
• “IS” stands for Image Stabilizer.
• “USM” stands for Ultrasonic Motor.
4. Ultrasonic motor (USM) for quick and quiet
autofocusing.
5. Manual focusing is available after the subject
comes into focus in autofocus mode (ONE
SHOT AF).
6. The zoom ring can be fixed to keep the lens at
the shortest point.
7. A truly round aperture hole results in a nicer
background blur.
8. Tight seal structure ensures excellent dustproof and drip-proof performance.
* Based on [1/focal length] second. Generally, it requires
a shutter speed [1/focal length] second or faster to
prevent camera shake.
Features
1. The Image Stabilizer gives the equivalent
effect of a shutter speed four stops faster*.
The lens also has a second image stabilizer
mode that is optimized for following shots of
moving subjects.
2. UD lens elements for excellent imaging
performance.
3. A fluorine coating has been applied to the
lens’s front and rear lens elements which
allows dust to be wiped from the outside of the
lens more easily compared with previous
lenses.
Thank you for purchasing a Canon product.
Conventions used in this instruction
Warning to prevent lens or camera malfunction
or damage.
Supplementary notes on using the lens and
taking pictures.
COPY
ENG-2
a Safety Precautions
a Safety Precautions
• Do not look at the sun or a bright light source
through the lens or camera. Doing so could result
in loss of vision. Looking at the sun directly through
the lens is especially hazardous.
• Whether it is attached to the camera or not, do
not leave the lens under the sun without the
lens cap attached. This is to prevent the lens from
concentrating the sun’s rays, which could cause a
fire.
Handling Cautions
• If the lens is taken from a cold environment into
a warm one, condensation may develop on the
lens surface and internal parts. To prevent
condensation in this case, first put the lens into an
airtight plastic bag before taking it from a cold to
warm environment. Then take out the lens after it
has warmed gradually. Do the same when taking
the lens from a warm environment into a cold one.
• Do not leave the lens in excessive heat such as in
a car in direct sunlight. High temperatures can
cause the lens to malfunction.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Do not make any changes or modifications to the equipment
unless otherwise specified in the instructions. If such changes or
modifications should be made, you could be required to stop
operation of the equipment.
This equipment has been tested and found to comply with the
limits for a class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for
help.
This Class B digital apparatus complies with Canadian ICES-003.
COPY
ENG-3
Nomenclature
Hood mount (→ 6)
Filter mounting
thread (→ 13)
Image stabilizer switch (→ 8)
Image stabilizer mode selector switch (→ 8)
Focus mode switch (→ 5)
Zoom ring (→ 5)
Focusing ring (→ 5)
Distance scale (→ 11)
Contacts (→ 4)
Lens mount index (→ 4)
Rubber ring (→ 4)
Tripod mounting location (→ 12)
Zoom ring lock
lever (→ 7)
For detailed information, reference page numbers are provided in parentheses (→ **).
COPY
ENG-4
See your camera’s instructions for details on
mounting and detaching the lens.
• After detaching the lens, place the lens with the
rear end up to prevent the lens surface and
electrical contacts from getting scratched.
• If the contacts get soiled, scratched, or have
fingerprints on them, corrosion or faulty
connections can result. The camera and lens
may not operate properly.
• If the contacts get soiled or have fingerprints on
them, clean them with a soft cloth.
• If you remove the lens, cover it with the dust
cap. To attach it properly, align the lens mount
index and the
K
index of the dust cap as shown
in the diagram, and turn clockwise. To remove it,
reverse the order.
1. Mounting and Detaching the Lens
The lens mount has a rubber ring for enhanced
water- and dust-resistance. The rubber ring may
cause slight abrasions around the camera's lens
mount, but this will not cause any problems. If the
rubber ring becomes worn, it is replaceable by a
Canon Service Center at cost.
COPY
Loading...