Candy CDI 1012-A - 80 User Manual

0 (0)

EN User instructions

CDI 1012

DISHWASHER

Congratulations!

Thank you for choosing a Candy appliance; quality dishwashers which guarantee high performance and reliability.

Candy manufacture a vast range of domestic appliances: washing machines, washer/dryers, cookers, microwave ovens, ovens and hobs, refrigerators and freezers.

Ask your dealer for the catalogue with the complete range of Candy products. Please read this booklet carefully as it provides important information regarding the safe installation, use, and maintenance of the machine, together with some useful advice on how to achieve the best results from your dishwasher.

For future reference please keep this instruction booklet in a safe place.

CUSTOMER SERVICE AND GUARANTEE

Your new appliance is fully guaranteed by the manufacturer for 12 months against electrical/mechanical breakdown excluding:

A.Any faults which occur due to bad installation or misuse of the machine.

B.Any faults which occur due to repair of, or interference with, the machine by any person not authorised by the manufacturer to carry out service.

C.Any faults which occur due to any parts which are fitted to the machine which are not the original manufacturers parts.

D.Any faults arising from non-domestic use or unusual or abnormal use of the machine.

E.Any faults arising from operation at incorrect voltage.

F.Any faults arising from incorrect operation of the machine.

The guarantee applies to Gt Britain and Northern Ireland only, and is an addition to your statutory rights.

AFTER SALES SERVICE

For service and repairs call your local engineer on our national telephone number:

GIAS Service	Tel: 08705 400 600
Support Service	(Eire 018301 666)

CONTENTS

Safety advice	pag.	4
Setting up, installation	pag.	5
Technical notes for cabinet fitters	pag.	8
Water softener unit	pag.	12
Adjusting the upper basket	pag.	14
Loading the dishes	pag.	15
Information for test laboratories	pag.	17
Loading the detergent	pag.	18
Types of detergent	pag.	19
Loading the rinse aid	pag.	20
Cleaning the filters	pag.	21
Some practical hints	pag.	22
Routine cleaning and maintenance	pag.	23
Description of the control panel	pag.	25
Technical data	pag.	25
Programme selection and special functions	pag.	26
Programme guide	pag.	28
Identifying minor faults	pag.	30

Fig. A

5	1
	1
	4

Please read the instructions in this booklet carefully because they contain important information on how to install, use and maintain your dishwasher safely as well as containing useful tips on how to make the most of it.

Keep this booklet safe for future reference.

SAFETY INSTRUCTIONS

There are certain basic safety rules which are valid for any domestic appliance.

Installation

■Make sure that the plug fitted to the machine is compatible with the power supply socket. If it is not, get a suitably qualified person to fit the correct type, and to make sure that the cables to the mains socket are able to cope with the power rating of the appliance.

■Ensure that the dishwasher does not crush power cables.

■In general it is not advisable to use adaptors, multiple plugs and/or extension cables.

■Should it be necessary to replace the supply cord, call the After Sales Service Centre.

Safety

■Never touch the appliance when your hands or feet are wet or damp.

■Do not use when your feet are bare.

■Do not remove the plug from the mains supply socket by pulling the mains cable or the machine itself.

■Do not leave the appliance exposed to the elements (rain, sun etc).

■This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

■Water left in the machine or on the dishes at the end of the wash programme should not be swallowed.

■The door should not be left in the open position since this could present a potential hazard ( es. tripping ).

■Leaning or sitting on the open door of the dishwasher could cause it to tip over.

WARNING !

Knives and other utensils with sharp points must be loaded in the basket with their points down or placed in a horizontal position.

Daily use

■This appliance is be designed for domestic use only.

■The dishwasher is designed for normal kitchen utensils.

Objects that have been contamined by petrol, paint, traces of steel or iron, corrosive chemicals, acids or alkalis must not be washed in the dishwasher.

■If there is a water softening device installed in the home there is no need to add salt to the water softener fitted in the dishwasher.

■Cutlery is washed best if it is placed in the basket with the handles downwards.

■If the appliance breaks down or stops working properly, switch it off, turn off the water supply and do not tamper with it. Repair work should only be carried out by an approved service agent and only genuine spare parts should be fitted. Any failure to follow the above advice may have serious consequences for the safety of the appliance.

Disposal

■The dishwasher has been made from materials which can be recycled so that it can be disposed of in an environmentally friendly way.

■If you wish to dispose of an old dishwasher be careful to remove the door to eliminate the risk of children becoming trapped inside it.

INSTALLATION

(Technical notes)

IMPORTANT

When the appliance is located on a carpet floor, attention must be paid to ensure that there is no obstruction to the bottom vents.

Make sure that the plug on the appliance remains accessible after installation.

Electrical connection

Plug your dishwasher into the power socket.

If the plug we supply does not fit :

■ CUT IT OFF AND DESTROY IT!

You can't use it on other appliances, and the exposed wires could be dangerous if anyone plugged it in.

■ Fit a suitable plug, as follows:

Connect

to the terminal in the plug

Marked with the letter E,

OR marked with the Earth

symbol,

Green and

yellow wire OR coloured green,

OR coloured green and yellow.

Marked N,

Blue wire

OR coloured black.

Marked L,

Brown wire

OR coloured red.

WARNING!

THIS APPLIANCE MUST BE EARTHED.

Fuses and plugs

This appliance should be used only on a socket with a minimum rating of 13 Amp.

Our ready-fitted plug is already equipped with a 13 amp fuse which is BS 1362 ASTA approved.

Any replacement should be exactly the same.

If the fuse cover is lost, do not use the plug until it is replaced.

A correct replacement fuse cover (obtainable from your dealer or Electricity board) must be the same colour as shown or named on the insert on the base of the plug.

Manufacturer declines all responsibility for any damage due to non-earthing of the machine.

Appliance complies with European Directives 73/23/EEC and 89/336/EEC, replaced by 2006/95/EC and 2004/108/EC, and subsequent amendments.

Water connection

IMPORTANT

The appliance must be connected to the water mains using new hose-sets. The old hose-sets should not be reused.

■The inlet and drain hoses can be directed to left or right.

IMPORTANT

The dishwasher can be connected to either cold or hot water, as long as it is no hotter than 60 °C.

■Water pressure must be between 0,08 MPa and 0,8 MPa. If the pressure is below the minimum consult our service department for advice.

■The inlet hose must be connected to a tap so that the water supply can be cut off when the machine is not in use

(fig. 1 B).

■The dishwasher is fitted with 3/4" threaded connector (fig. 2).

■Connect inlet hose “A” to water tap “B” with a 3/4" attachment making sure that it has been properly tightened.

■If it is necessary, the inlet pipe can be lengthened up to 2,5 m. The extension pipe is available from the After Sales Service Centre.

■If limescale deposits or sand are present in the water, it is advisable to obtain the appropriate filter, art. 9226085, from the After Sales Service Centre (fig. 3). The filter “D” must be inserted between the tap “B” and the inlet hose “A” , remembering to fit the washer “C” .

■If the dishwasher is connected to new pipes or to pipes which have not been in use for a long time run water through for a few minutes before connecting the inlet hose. In this way no deposits of sand or rust will clog up the water inflow filter.

Connecting the outlet hose

■The outlet hose should disharge into a standpipe, making sure that there are no kinks (fig. 4).

■The standpipe must be at least 40 cm above floor level and it must have an internal diameter of at least 4 cm.

■It is advisable to fit an anti-odour air trap

(fig. 4X).

■If necessary the outlet hose can be extended up to 2,5 m, provided that it is kept at a maximum height of 85 cm above floor level. The extension pipe is available from the After Sales Service Centre.

■The hose can be hooked over the side of the sink, but it must not be immersed in water, in order to prevent water from being syphoned back to the machine when this is in operation (fig. 4Y).

■When installing the appliance under a worktop the hose pipe clamp must be attached to the wall in the highest possible position under the worktop (fig. 4Z).

■Check that there are no kinks in the inlet and outlet hoses.

Opening the door

Closing the door

Put your hand into the recess and pull.

If the machine comes open while it is working, an electrical safety device automatically switches everything off.

IMPORTANT

For the machine to work properly, the door should not be opened while it is in operation.

Place the baskets in the machine.

Make sure that both the spray arms are free to rotate and are not obstructed by cutlery, crockery or pans. Close the door, pressing on it to make sure it is firmly shut.

TECHNICAL NOTES FOR CABINET FITTERS

This dishwasher model can be embedded in modular furniture, under a counter top, a continuous counter top or a sink.

■The housing dimensions must be the same as those indicated in the figure 1.

■The adjustable feet allow the height of the machine to be varied from 820 to 900 mm.

Installation under the counter top

■Adjust the dishwasher height to adapt it to the housing “A” dimensions, level it by means of the adjustable feet (fig. 2-3).

■Insert the dishwasher in the housing and connect the dishwasher to water and power following the instruction booklet; if necessary, re-adjust the front and rear feet.

■Fasten the dishwasher with the supplied 16 mm long screws “A” , as indicated in the figure 4.


570				1
570
600
600
	550
820+(80)		598				820+(80)
		598
	+(80)
160	100				170
40


550	100
550	100		597
			597

Wooden panel installation

This dishwasher model is equipped with an auto-balancing system in the door and comes ready to mount a wooden panel of the following size:

Width 596,5 mm max

Height from 645 to 715 mm max

Thickness from 18 to 22 mm max

This allows the use of a regular wing taken from a drawer furniture weighing from 3 to 7 kg; for coverings weighing more, ask for information to the Assistance Service.

Drilling arrangements

■Drill 12 mm deep holes in the panel using a 2 mm diameter drill according to the measures indicated in the figure 5.

■Fasten the two supplied frames with 4 of the 4 x 16 mm diameter screws, setting them at the center of the eyelets (fig. 6).

■Hang the panel on the dishwasher door and align it by adjusting the frames with the eyelets.

■Fix the frames with the other 6 screws 4x16 mm in the specif holes (fig. 6).

■Fasten the panel to the dishwasher door with the screws 3.5 x 13 mm (fig. 7).

N.B.:

If you wish to fit a wooden panel with false drawer, ask for special kit to the Assistance Service.

5
		=	572	=
		178
715 max.	645 min.	350
			596,5 max.
				9

Important

If, after mounting the wooden panel, it is necessary to ship the machine for final installation, we recommend leaving it in its original packaging materials.

For this reason the package was design to allow the panel to be mounted without having to unpack the machine completely. Follow figures 8a-f sequentially.

A)Cut the polythene with a Knife (fig. 8a).

B)Lift the cardboard flap up and remove the wooden slat (fig. 8b).

C)To open the dishwasher remove the polystyrene from the sides (fig. 8c).

D)Fix the décor panel to the matching kitchen door (fig. 5-6), then while the dishwasher door is in the open position attach it to the machine using the 6 screw 3.5 x 13 mm (fig. 8d).

E)Replace the cardboard and film in its original position (fig. 8e).

F)Re–seal the packaging(fig. 8f).

Adaptation of the base

Sometime, in order to allow the door rotation, a space must be cut out in the base as indicated in the figure 9.

Proceed as follows:

■Open slightly the dishwasher door, let the covering touch the base and mark its lower edge on the base with a pencil; cut out the interfering part.

620 min.

+ 11 hidden pages