Campbell Hausfeld IN729000AV, SB5240, SB524000 User Manual

6.02 Mb
Loading...

See Warranty on page 10 for important information about commercial use of this product.

Operating Instructions

SB524000

 

 

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference.

2 inch 2-in-1 Nailer/Stapler

Table of Contents

 

Description . . . . . . . . . . . . . . . . . . . . . .

1

Unpacking . . . . . . . . . . . . . . . . . . . . . . .1

Safety Guidelines . . . . . . . . . . . . . . . . .1

Important Safety Instructions . . . . . . .2

Tool Components and Specifications . .2

Operating the Tool . . . . . . . . . . . . . . . .4

Recommended Hookup . . . . . . . . . . . .5

Maintenance . . . . . . . . . . . . . . . . . . . . .7

Storage . . . . . . . . . . . . . . . . . . . . . . . . .

7

Fasteners . . . . . . . . . . . . . . . . . . . . . . . .8

Troubleshooting Chart .. .. .. .. .. .. .. .. .. .. .. .. ..9

Warranty . . . . . . . . . . . . . . . . . . . . . . .10

Description

This tool is designed for decorative trim, molding, window casings, furniture trim, picture frame assembly, cabinetry, casebacks, and crafts.. Features include: convenient top loading magazine which holds up to 100 brads or staples, adjustable depth control, adjustable exhaust nose..

Unpacking

After unpacking the unit, inspect carefully for any damage that may have occurred during transit.. Check for loose, missing or damaged parts.. Make sure to tighten fittings, bolts, etc.., before putting unit into service..

Check to be sure all supplied accessories are enclosed with the unit.. In case of questions, damaged or missing parts, please call 1-800-543-6400 for customer assistance..

Figure 1 - Model SB524000

Read & Follow All Instructions

Save These Instructions

Do Not Discard

Safety Guidelines

This manual contains information that is very important to know and understand.. This information is provided for SAFETY and to PREVENT EQUIPMENT PROBLEMS.. To help recognize this information, observe the following symbols..

Danger indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.

Warning indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury.

Caution indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury.

Notice indicates important information, that if not followed, may cause damage to equipment.

NOTE: Information that requires special attention..

REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.

© 2009 Campbell Hausfeld/Scott Fetzer

For parts, product & service information

IN729000AV 9/09

 

visit www.chpower.com

 

Operating Instructions

Important Safety Instructions

 

 

equipment.. Follow all instructions..

Personal Safety

INSTRUCTIONS PERTAINING TO A

 

 

Contact your Campbell Hausfeld

a..

Stay alert. Watch what you are

 

 

representative if you have any

 

 

 

doing and use common sense

RISK OF FIRE, ELECTRIC SHOCK, OR

 

 

 

 

 

questions..

 

 

 

 

when operating the tool. Do not

INJURY TO PERSONS

 

 

 

 

 

 

 

 

 

c.

Only persons well acquainted with

 

use the tool while tired or under

 

 

 

When using tools,

 

 

 

 

 

 

these rules of safe operation should

 

the influence of drugs, alcohol,

 

 

 

 

 

 

 

 

 

basic precautions

 

 

 

 

 

 

 

 

 

 

 

 

 

 

be allowed to use the unit..

 

or medication. A moment of

should always be followed, including

 

 

 

the following:

 

 

 

Read and

 

inattention while operating the

 

 

 

 

California proposition 65

 

 

 

understand tool

 

tool increases the risk of injury to

 

 

 

 

labels and manual. Failure to follow

 

persons..

 

 

 

This product or

 

 

 

 

warnings, dangers, and cautions could

b..

Dress properly. Do not wear loose

 

 

 

 

 

 

 

 

 

its power cord may

result in DEATH or SERIOUS INJURY.

 

 

 

 

 

 

 

clothing or jewelry. Contain long

contain chemicals known to the State

Work Area

 

of California to cause cancer and birth

 

hair. Keep hair, clothing, and

defects or other reproductive harm.

a..

Keep the work area clean and well

 

gloves away from moving parts.

Wash hands after handling.

 

 

 

lighted. Cluttered benches and dark

 

Loose clothes, jewelry, or long

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

areas increase the risks of electric

 

hair increases the risk of injury to

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

shock, fire, and injury to persons..

 

persons as a result of being caught

You can create dust when

 

 

 

 

 

b..

Do not operate the tool

 

 

in moving parts..

 

 

 

you cut, sand, drill or grind

 

 

 

 

 

 

 

in explosive atmospheres,

 

c..

Avoid unintentional starting.

 

 

 

 

 

 

 

 

materials such as wood,

 

 

 

 

such as in the presence of

 

 

Be sure the switch is off before

paint, metal, concrete, cement, or other

 

 

 

 

masonry. This dust often contains

 

 

flammable liquids, gases,

 

 

connecting to the air supply. Do not

 

 

 

 

chemicals known to cause cancer, birth

 

 

or dust. The tool is able to create

 

carry the tool with your finger on

defects, or other reproductive harm.

 

 

sparks resulting in the ignition of

 

the switch or connect the tool to th

Wear protective gear.

 

 

 

 

 

the dust or fumes..

 

air supply with the switch on..

 

 

 

 

 

 

 

 

General

c..

Keep bystanders, children, and

d..

Do not overreach. Keep proper

 

 

 

 

 

 

 

 

visitors away while operating the

 

footing and balance at all times.

a.. To reduce the risks of

 

 

 

 

 

electric shock, fire, and

 

 

 

tool. Distractions are able to result in

 

Proper footing and balance enables

 

injury to persons, read all

 

 

 

the loss of control of the tool..

 

better control of the tool in

 

the instructions before

 

 

 

 

 

 

 

unexpected situations..

 

 

 

 

 

 

 

 

 

using the tool.

 

 

 

 

 

e..

Use safety equipment. A dust mask,

 

 

 

 

 

 

 

 

 

 

b. Be thoroughly familiar with the

 

 

 

 

 

 

non-skid safety shoes and a hard

 

controls and the proper use of the

 

 

 

 

 

 

 

Tool Components and Specifications

Requires: 0..4 SCFM with 10

 

fasteners per minute @ 90 psi

 

Air inlet: 1/4 inch NPT

 

MAGAZINE CAPACITY: 100 fasteners per

 

load, 18 gauge

 

BRADS: 3/8 inch to 2 inch

 

STAPLES: 1/2 inch to 1-1/2 inch;

 

1/4 inch crown

 

WEIGHT: 3 lbs.., 1 oz..

 

LENGTH: 9-3/4 inch

 

HEIGHT: 9-1/2 inch

Work

MAXIMUM PRESSURE: 120 psi

Contact

PRESSURE RANGE: 70 psi - 120 psi

Element

 

Adjustable Direction

Exhaust Deflector

Trigger

Adjustable

Depth Control

Nail Loading Area

Magazine

Nail Discharge Area

www.chpower.com

2

 

 

 

 

SB524000

Important Safety Instructions

d..

Disconnect the tool from the

Never attach air line to tool or carry

(Continued)

 

air source before making any

tool while touching the trigger. The tool

 

could eject a fastener which will result

 

hat must be used for the applicable

 

adjustments, changing accessories,

 

 

in death or serious personal injury.

 

 

or storing the tool. Such preventive

 

conditions..

 

 

 

 

safety measures reduce the risk of

 

f..

Always wear eye

 

 

 

starting the tool unintentionally..

 

 

protection.

 

Always disconnect the

 

e..

Store the tool when it is idle out

g..

Always wear hearing

tool from the power

 

of reach of children and other

source when unattended,

 

protection when using

 

 

 

untrained persons. A tool is

performing any maintenance or repair,

 

the tool. Prolonged exposure to

 

 

 

dangerous in the hands of untrained

loading or unloading, clearing a jam,

 

high intensity noise is able to cause

 

or moving the tool to a new location.

 

 

users..

 

hearing loss..

 

Do not load the tool with fasteners

 

 

 

h..

Do not attach the hose or tool to

f..

Maintain the tool with care. Keep

when either the trigger is depressed

 

a cutting tool sharp and clean.. A

or the Work Contact Element (WCE) is

 

your body. Attach the hose to the

 

engaged. The tool could eject a fastener

 

 

properly maintained tool, with sharp

 

structure to reduce the risk of loss of

 

causing death or serious personal

 

 

cutting edges reduces the risk of

 

balance if the hose shifts..

 

injury.

 

 

binding and is easier to control..

 

i..

Always assume that the tool

 

 

g.. Check for misalignment or binding

 

 

contains fasteners. Do not point

 

 

 

of moving parts, breakage of parts,

Always fit tool with a

 

the tool toward yourself or anyone

 

 

 

and any other condition that affects

fitting or hose coupling

 

whether it contains fasteners or not..

 

 

 

the tool’s operation. If damaged,

on or near the tool in

 

 

 

j.

Do not nail on

 

such a manner that all compressed air

 

have the tool serviced before using..

 

top of another

 

in the tool is discharged at the time the

 

 

Many accidents are caused by poorly

 

 

fitting or hose coupling is disconnected.

 

nail. This is able to cause the nail to

 

 

 

maintained tools.. There is a risk of

 

 

Do not use a check valve or any other

 

be deflected and hit someone, or

 

 

 

bursting if the tool is damaged..

fitting which allows air to remain in the

 

cause the tool to react and result in a

 

 

risk of injury to persons.

h.. Use only accessories that are

tool. Death or serious personal injury

 

could occur.

 

 

k..

Remove finger

 

identified by the manufacturer for

 

 

 

from the trigger

 

the specific tool model. Use of an

 

 

when not driving fasteners. Never

 

accessory not intended for use with

 

 

carry the tool with finger on trigger,

 

Never place hands or any

 

 

the specific tool model, increases the

 

the tool is able to fire a fastener.

 

other body parts in the

 

 

risk of injury to persons..

 

Always remain in a

 

fastener discharge area of

 

i.

Selecting an appropriate tool

the tool. The tool might eject a fastener

 

firmly balanced

 

and could result in death or serious

position when using or handling the

 

actuation system, taking into

 

personal injury.

tool.

 

consideration the work application

 

 

 

Avoid long extended

 

for which the tool is used..

 

 

periods of work

 

Never use

Never carry the tool by

with the tool. Stop using the tool if you

 

 

gasoline

feel pain in hands or arms.

 

the air hose or pull the

or other flammable liquids

 

 

hose to move the tool

Tool Use and Care

to clean the tool. Never use

or a compressor. Keep hoses away from

the tool in the presence of

a..

Use clamps or another practical way

heat, oil and sharp edges. Replace any

flammable liquids or gases. Vapors

hose that is damaged, weak or worn.

 

to secure and support the workpiece

could ignite by a spark and cause an

 

Personal injury or tool damage could

 

to a stable platform. Holding the

explosion which will result in death or

 

occur.

 

work by hand or against the body is

serious personal injury.

Always assume the

 

 

 

 

unstable and is able to lead to loss

 

 

 

 

 

tool contains

 

of control..

Do not remove, tamper

fasteners. Respect the tool as a working

b..

Do not force the tool. Use the

implement; no horseplay. Always keep

with, or otherwise

others at a safe distance from the work

 

correct tool for the application.. The

 

cause the Work Contact

area in case of accidental discharge of

 

correct tool will do the job better

Element (WCE) or trigger to become

fasteners. Do not point the tool toward

 

and safer at the rate for which the

inoperable. Do not operate any tool

yourself or anyone whether it contains

 

tool is designed..

which has been modified in a like

fasteners or not. Accidental triggering

 

fashion. Death or serious personal

of the tool could result in death or

c..

Do not use the tool if the switch

injury could result.

serious personal injury.

 

does not turn the tool on or off. Any

 

 

 

 

tool that cannot be controlled with

 

 

 

 

the switch is dangerous and must be

Do not touch the trigger

 

 

repaired..

unless driving fasteners.

 

www.chpower.com

3

120 psi
70 psi Min..
120 psi Max..
O CO2

Operating Instructions

Important Safety Instructions (Continued)

Do not drive a fastener on top of other fasteners. The fastener

could glance and cause death or a serious puncture wound.

! WARNING

Do not operate or allow anyone else to operate the tool if any warnings

or warning labels are not legible. Warnings or warning labels are located on the tool magazine and body.

Do not drop or throw the tool.

Dropping or throwing the tool can result in damage that will make the tool unusable or unsafe. If the tool has been dropped or thrown, examine the tool closely for bent, cracked or broken parts and air leaks. STOP and repair before using or serious injury could occur.

Always check that the Work Contact

Element (WCE) is operating properly. A fastener could accidentally be driven if the WCE is not working properly. Personal injury may occur (See "Checking the Work Contact Element" Section).

Avoid using the tool when the

magazine is empty. Accelerated wear on the tool may occur.

Clean and check all air supply hoses

and fittings before connecting the tool to an air supply. Replace any damaged or worn hoses or fittings. Tool performance or durability may be reduced.

Service

a..Tool service must be performed only by qualified repair personnel.

b..When servicing a tool, use only identical replacement parts. Use only authorized parts.

c..Use only the lubricants supplied with the tool or specified by the manufacturer.

Do not make any modifications to

the tool without first obtaining written approval from Campbell Hausfeld. Do not use the tool if any shields or guards are removed or altered. Do not use the tool as a hammer. Personal injury or tool damage may occur.

Disconnect air supply and release

tension from the pusher before attempting to clear jams because fasteners can be ejected from the front of the tool. Personal injury may occur.

Air Source

a..Never connect to an air source that is capable of exceeding 200 psi.

Over pressurizing the tool is able to result in bursting, abnormal operation, breakage of the tool or serious injury to persons.. Use only clean, dry, regulated compressed air at the rated pressure or within the rated pressure range as marked on

the tool.. Always verify prior to using the tool that the air source has been adjusted to the rated air pressure or within the rated air-pressure range..

b..Never use oxygen, carbon dioxide, combustible gases or any bottled gas as an air source for the tool.

Such gases are capable of explosion and serious injury to persons..

Do not use any type of reactive gases, including, but not limited to, oxygen and

combustible gases, as a power source. Use filtered, lubricated, regulated compressed air only. Use of a reactive gas instead of compressed air may cause the tool to explode which will cause death or serious personal injury.

Use only a pressure-regulated compressed air source to limit the air pressure supplied to

the tool. The regulated pressure must not exceed 120 psi. If the regulator fails, the pressure delivered to the tool must not exceed 200 psi. The tool

could explode which will cause death or serious personal injury.

Save These Instructions

Do Not Discard

Operating The Tool

Lubrication

This tool requires lubrication before using the tool for the first time and before each use.. If an inline oiler is used, manual lubrication through the air inlet is not required on a daily basis..

The work surface can become

damaged by excessive lubrication. Proper lubrication is the owner’s responsibility. Failure to lubricate the tool properly will dramatically

shorten the life of the tool and void the warranty.

1. Disconnect the air supply from the tool to add lubricant..

2.Turn the tool so the air inlet is facing up.. Place 4-5 drops of 30 W non-detergent oil into air inlet.. Do not use detergent oils, oil

additives, or air tool oils.. Air tool oils contain solvents which will damage the tool’s internal components..

3.After adding oil, run

tool briefly.. Wipe off any excess oil from the cap exhaust..

Recommended Hookup

The illustration below shows the recommended hookup for the tool..

1. The air

compressor must be able

to maintain a minimum of 70 psi when the

tool is being used.. An inadequate air supply can cause a loss of power and inconsistent driving..

2. An oiler can be used to provide oil circulation through the tool.. A filter can be used to remove liquid and solid

impurities which can rust or “gum up” internal parts of the tool..

www.chpower.com

4

150 psi WP
3/8 inch I..D..

SB524000

Operating The Tool (Continued)

3. Use 1/4 inch air hoses with a minimum working pressure of 150 psi.. Use 3/8 inch air hoses for 50 foot run or longer.. For

better performance, install a 3/8 inch quick plug (1/4 inch NPT threads) with an inside diameter of ..315 inch (8mm) on the tool and a 3/8 inch quick coupler on the air hose..

4.Use a pressure regulator on the compressor, with an operating pressure of 0 psi - 125 psi.. A pressure regulator is required to control

the operating pressure of the tool between 70 psi and 120 psi..

Single SEQUENTIAL Mode

This mode

requires the

trigger to be pulled

each time a fastener is driven.. The tool can be actuated by depressing the WCE against the work surface followed by pulling the trigger..

The trigger must be released to reset the tool before another fastener can be driven..

Checking the Work Contact Element (WCE)

Check the operation of the Work Contact

Element (WCE) trip mechanism before each use. The WCE must move freely without binding through its entire travel distance. The WCE spring must return the WCE to its fully extended position after being depressed. Do not operate the tool if the WCE trip mechanism is not operating properly. Personal injury may occur.

1. Disconnect the air supply from the tool..

2. Remove all fasteners from the magazine (see Loading/ Unloading)..

3.Make sure the trigger and work contact

element (WCE) move freely up and down without sticking or binding..

4. Reconnect air supply to the tool..

5. Depress the Work

Contact Element (WCE) against the work surface without

pulling the trigger.. The tool must not

operate.. Do not use the tool if it operates without pulling the trigger.. Personal injury may result..

6.Remove the tool from the work surface.. The Work Contact Element (WCE) must return to its original

down position.. The tool must not operate.. Do not use the tool if it operates while lifted from the work surface.. Personal injury may result..

7.Pull the trigger and depress the work contact

element (WCE) against the work surface.. The tool MUST NOT operate..

8.Depress the Work Contact Element (WCE)

against the work surface.. Pull the trigger.. The tool MUST operate..

Recommended Hookup

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Quick

Regulator

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Quick

 

 

Quick Plug

Coupler

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Quick Plug Coupler

 

 

(Optional)

(Optional)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Air Hose

Lubricator

Filter

www.chpower.com

5

Operating Instructions

Operating The Tool (Continued)

An improperly functioning tool

must not be used. Do not actuate the tool unless the tool is placed firmly against the work piece.

LOADING/UNLOADING THE TOOL

1.Always disconnect the tool from the air supply before loading fasteners..

2.Push

down on LatchButton

the latch button..

Pull back on the magazine cover..

3a. For nails,

insert a stick of

Campbell

Hausfeld

nails or equivalent (see “Fasteners” section) into the magazine.. Make sure the pointed ends of the fasteners are resting on the bottom ledge of the magazine when loading.. Make sure the nails are not dirty or damaged..

3b.

For

 

 

staples,

 

 

load a clip

 

 

of staples

Magazine Rail

 

with the

 

 

 

crowns straddling the magazine rail..

4.

Push the

 

 

magazine

 

 

cover

 

 

forward

 

 

until latch

 

 

button pops up..

 

5.Always unload all fasteners before removing tool from service.. Unloading is the reverse of loading, except that you must disconnect the air supply before unloading..

ADJUSTING THE FASTENER PENETRATION

The tool is equipped with an adjustable depth of drive feature.. This allows the user to determine how deep a fastener will be driven into the work surface..

1.Adjust operating pressure so fasteners are driven consistently.. Do not exceed 120 psi..

2.For shallow penetration, turn the wheel (C) to right to the extent desired..

(C)

3.For deeper penetration, turn the wheel (C) to left to the extent desired..

4.Make sure trigger and work contact element

(WCE) move freely up and down without binding or sticking after each adjustment..

Adjusting The Direction Of The Exhaust

The tool is equipped with an

adjustable Rotate direction

exhaust deflector.. This is intended to allow the user to change the direction of the exhaust.. Simply twist the deflector to any direction desired..

CLEARING A JAM FROM THE TOOL

1. Disconnect the air supply from the tool..

2. Remove all

nails from the magazine

(See Loading/ Unloading

The Nailer)..

Failure to do so will cause the nails to eject from the front of the nailer when the nose assembly is removed..

3.Loosen cap screws on nose of tool.. Slide nose downward and remove from tool to expose jammed fastener..

4.Reinstall nose assembly in reverse order in step #3..

5.Make sure the trigger and Work Contact Element (WCE) move freely up and down without sticking or binding..

Failure to remove all fasteners will cause the fasteners to eject from the

front of the tool.

www.chpower.com

6

SB524000

Maintenance

Technical Support

Please call our Tool Hotline at 1-800- 543-6400 with any questions regarding the operation or repair of this tool or for additional copies of this manual..

Fastener And Replacement Parts

Use only genuine Campbell Hausfeld

18 gauge fasteners (or equivalent - see Fastener Interchange Information). Tool performance, safety and durability could be reduced if improper fasteners are used. When ordering replacement parts or fasteners, specify by part number.

Tool Repair

Only qualified personnel should repair the tool, and they should use genuine Campbell Hausfeld replacement parts and accessories, or parts and accessories which perform equivalently..

Assembly Procedure For Seals

When repairing a tool, the internal parts must be cleaned and lubricated.. Parker O-lube or equivalent must be used on all o-rings.. Each o-ring must be coated with O-lube before assembling.. A small amount of oil must be used on all moving surfaces and pivots..

After reassembling, a few drops of 30W non-detergent oil or equivalent, must be added through the air line before

testing..

Storage

The unit should be stored in a cool, dry place..

Notes

www.chpower.com

7

Operating Instructions

Fasteners

Nails

The following Campbell Hausfeld Brad nails are available at local retail stores.. For help locating any item, call customer service at 1-800-543-6400.. Campbell Hausfeld nails meet or exceed ASTM Standard F1667..

Model #

Length

Shank Gauge

Finish

Head

Collation

Nails per Pack

Nails per

 

 

 

 

 

 

 

Box

FB001600

5/8 inch

18 Gauge

Galvanized

Brad /Brown

Adhesive

100

5000

FB002000

3/4 inch

18 Gauge

Galvanized

Brad /Brown

Adhesive

100

5000

FB002500

1 inch

18 Gauge

Galvanized

Brad /Brown

Adhesive

100

5000

FB003000

1-1/4 inch

18 Gauge

Galvanized

Brad /Brown

Adhesive

100

5000

FB004000

1-1/2 inch

18 Gauge

Galvanized

Brad /Brown

Adhesive

100

5000

FB004500

1-3/4 inch

18 Gauge

Galvanized

Brad /Brown

Adhesive

100

5000

FB005000

2 inch

18 Gauge

Galvanized

Brad /Brown

Adhesive

100

5000

FB180016

5/8 inch

18 Gauge

Galvanized

Brad /Brown

Adhesive

100

1000

FB180025

1 inch

18 Gauge

Galvanized

Brad /Brown

Adhesive

100

1000

FB180030

1-1/4 inch

18 Gauge

Galvanized

Brad /Brown

Adhesive

100

1000

FB180040

1-1/2 inch

18 Gauge

Galvanized

Brad /Brown

Adhesive

100

1000

FB180050

2 inch

18 Gauge

Galvanized

Brad /Brown

Adhesive

100

1000

Interchange Information

Can use brad nails from the following branded air-powered brad nailers: Bostitch BT125SK-2 & BT200K-2, Campbell Hausfeld NB0030 & NB0040, DeWalt D51238K, Paslode T125-F18 & T200-F18, Porter Cable BN125 & BN200, and Senco Finish Pro 15 & 18..

Staples

The following Campbell Hausfeld staples are available at local retail stores.. If you need help locating any item, call customer service at 1-800-543-6400.. Campbell Hausfeld staples meet or exceed astm Standard F1667..

Model #

Length

Wire

Crown Size

Point

Finish

Collation

Staples Per

Staples

 

 

Diameter

 

 

 

 

Stick

Per Box

FN158K00

1/2 inch

18 Gauge

1/4 inch

Chisel

Galvanized/

Adhesive

100

5000

 

 

 

 

 

Vinyl Coated

 

 

 

FN168K00

5/8 inch

18 Gauge

1/4 inch

Chisel

Galvanized/

Adhesive

100

5000

 

 

 

 

 

Vinyl Coated

 

 

 

FN180615

1/2 inch

18 Gauge

1/4 inch

Chisel

Galvanized/

Adhesive

100

1000

 

 

 

 

 

Vinyl Coated

 

 

 

FN180620

3/4 inch

18 Gauge

1/4 inch

Chisel

Galvanized/

Adhesive

100

1000

 

 

 

 

 

Vinyl Coated

 

 

 

FN180625

1 inch

18 Gauge

1/4 inch

Chisel

Galvanized/

Adhesive

100

1000

 

 

 

 

 

Vinyl Coated

 

 

 

FN180630

1-1/4 inch

18 Gauge

1/4 inch

Chisel

Galvanized/

Adhesive

100

1000

 

 

 

 

 

Vinyl Coated

 

 

 

FN208K00

3/4 inch

18 Gauge

1/4 inch

Chisel

Galvanized/

Adhesive

100

5000

 

 

 

 

 

Vinyl Coated

 

 

 

FN258K00

1 inch

18 Gauge

1/4 inch

Chisel

Galvanized/

Adhesive

100

5000

 

 

 

 

 

Vinyl Coated

 

 

 

Interchange Information

Staples used in the SB524000 will also work in: Senco LN4450, SJS-LR, SKS L11-15, Hitachi N3804A, Duofast BN-1832S, KN1848, Stan-Tech SDS 18-14, Atro Minor 90/30, 90/32, 90/40, and Porter Cable NS100..

www.chpower.com

8

+ 24 hidden pages