Campbell Hausfeld SB660000, IN734600AV User Manual

9.64 Mb
Loading...

See Warranty on page 10 for important information about commercial use of this product.

Operating Instructions

SB660000

 

 

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference.

3-in-1 Finish

Nailer / Stapler

Table of Contents

Description . . . . . . . . . . . 1 Unpacking . . . . . . . . . . . 1 Safety Guidelines . . . . . . . . 1 Important Safety Information . . . 1

Tool Components and

Specifications . . . . . . . . . . 2 Operating Instructions . . . . . . 4 Lubrication . . . . . . . . . . 4 Recommended Hookup . . . . . 4 Operational Mode . . . . . . . 5 Work Contact Element (WCE) . . 5 Loading/Unloading The Tool . . . 5

Adjusting the Fastener

Penetration . . . . . . . . . . 6

Adjusting the Direction

of the Exhaust . . . . . . . . . 6 User-Maintenance Instructions . . . 6 Clearing A Jam From The Tool . . 6 Technical Service . . . . . . . . 6 Fastener And Replacement Parts . 6 Tool Repair . . . . . . . . . . 6 Assembly Procedure For Seals . . 6 Fasteners . . . . . . . . . . . . 7 Troubleshooting Chart . . . . . . . . . . . . 9 Warranty . . . . . . . . . . . 10

Description

This tool, which drives 3 different types of fasteners (18 gauge brads, 18 gauge 1/4 inch crown staples, and 16 gauge finish nails) is designed for decorative trim, molding, window casings, furniture trim, picture frame assembly, cabinetry, setting pre-hung doors, casebacks, and crafts. Features include: convenient top and side loading magazine which holds up to

100 fasteners, adjustable depth control, rubber grip, adjustable exhaust, and quick clear nose.

Unpacking

After unpacking the unit, inspect carefully for any damage that may have occurred during transit. Make sure to tighten fittings, bolts, etc., before putting unit into service.

Safety Guidelines

This manual contains information that is very important to know and understand. This information is provided for SAFETY and to PREVENT EQUIPMENT PROBLEMS. To help

recognize this information, observe the following symbols.

Danger indicates an imminently

hazardous situation which, if not avoided, WILL result in death or serious injury.

Warning indicates a potentially

hazardous situation which, if not avoided, COULD result in death or serious injury.

Caution indicates a potentially

hazardous situation which, if not avoided, MAY result in minor or moderate injury.

Notice indicates important

information, that if not followed, may cause damage to equipment.

NOTE: Information that requires special attention.

Model SB660000

Locate model and date code on tool and record below:

Model No.: _____________________

Date Code: _____________________

Retain these numbers for future reference.

When using tools, basic precautions should always be followed, including

the following:

California proposition 65

This product or

its power cord may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Wash hands after handling.

Important Safety Instructions

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS

This manual contains safety, operational and maintenance information. Contact your Campbell Hausfeld representative if you have any questions.

You can create dust when you cut, sand, drill or grind materials such as wood,

paint, metal, concrete, cement, or other masonry. This dust often contains chemicals known to cause cancer, birth defects, or other reproductive harm. Wear protective gear.

REMINDER: Keep your dated proof of purchase for warranty purposes!

Attach it to this manual or file it for safekeeping.

Campbell Hausfeld Nailers meet or exceed Industries’ Standards as set forth by the American IN734600AV 9/10 National Standard Institute/International Staple, Nail and Tool Association in ANSI/ISANTA

SNT-101-2002.

© 2010 Campbell Hausfeld/Scott Fetzer

For parts, product & service information

visit www.chpower.com

 

Operating Instructions

 

 

 

 

 

 

 

SB660000

 

 

 

 

 

 

 

 

 

 

 

 

 

Important Safety Instructions

c.

Keep bystanders, children, and

f.

Always wear eye

 

 

(Continued)

 

visitors away while operating the

 

protection.

 

General

 

tool. Distractions are able to result in

 

 

 

 

 

 

 

 

the loss of control of the tool.

 

 

 

 

 

 

 

a.

To reduce the risks of

 

 

g.

Always wear hearing

 

 

 

 

 

 

electric shock, fire, and

 

Personal Safety

 

 

injury to persons, read all

 

a.

Stay alert. Watch what you are

 

protection when using

 

 

 

 

the tool. Prolonged

 

 

the instructions before

 

 

 

 

 

 

doing and use common sense

 

 

 

 

 

 

exposure to high intensity

 

 

using the tool.

 

 

 

 

 

when operating the tool. Do not

 

 

 

 

 

 

 

 

 

 

 

 

noise is able to cause hearing loss.

b. Be thoroughly familiar with the

 

use the tool while tired or under

 

 

h. Do not attach the hose or tool to

 

controls and the proper use of the

 

the influence of drugs, alcohol,

 

equipment. Follow all instructions.

 

or medication. A moment of

 

your body. Attach the hose to the

 

Contact your Campbell Hausfeld

 

inattention while operating the

 

structure to reduce the risk of loss of

 

representative if you have any

 

tool increases the risk of injury to

 

balance if the hose shifts.

 

questions.

 

persons.

i.

Always assume that the tool

c.

Only persons well acquainted with

b.

Dress properly. Do not wear loose

 

contains fasteners. Do not point

 

these rules of safe operation should

 

clothing or jewelry. Contain long

 

the tool toward yourself or anyone

 

be allowed to use the unit.

 

hair. Keep hair, clothing, and

 

whether it contains fasteners or not.

 

 

Read and

 

gloves away from moving parts.

j.

 

 

 

 

Do not nail on

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

understand tool

 

Loose clothes, jewelry, or long

 

 

 

 

 

top of another

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

labels and manual. Failure to follow

 

hair increases the risk of injury to

 

nail. This is able to cause the nail to

warnings, dangers, and cautions could

 

 

be deflected and hit someone, or

 

persons as a result of being caught

 

result in DEATH or SERIOUS INJURY.

 

 

cause the tool to react and result in a

 

in moving parts.

 

Work Area

 

 

risk of injury to persons.

c.

Avoid unintentional starting.

k.

 

 

 

 

Remove finger

a.

Keep the work area clean and well

 

 

 

 

 

 

 

 

 

Be sure the switch is off before

 

 

 

 

 

from the trigger

 

 

 

 

 

 

 

lighted. Cluttered benches and dark

 

connecting to the air supply. Do not

 

when not driving fasteners. Never

 

areas increase the risks of electric

 

carry the tool with your finger on

 

carry the tool with finger on trigger,

 

shock, fire, and injury to persons.

 

the switch or connect the tool to the

 

the tool is able to fire a fastener.

b. Do not operate the tool

 

 

air supply with the switch on.

 

 

 

 

Always remain in a

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

firmly balanced

 

in explosive atmospheres,

 

d.

Do not overreach. Keep proper

 

 

 

 

 

 

position when using or handling the

 

such as in the presence of

 

 

footing and balance at all times.

tool.

 

flammable liquids, gases,

 

 

Proper footing and balance enables

 

 

 

 

Avoid long extended

 

or dust. The tool is able to create

 

better control of the tool in

 

 

 

 

periods of work

 

 

 

 

 

 

 

 

 

 

 

 

 

sparks resulting in the ignition of

 

unexpected situations.

with the tool. Stop using the tool if you

the dust or fumes.

e. Use safety equipment. A dust mask,

feel pain in hands or arms.

 

 

 

 

non-skid safety shoes and a hard

 

 

hat must be used for the applicable

 

 

conditions.

 

Tool Components and Specifications

Requires: 0.7 SCFM with

 

Adjustable Exhaust

 

 

 

 

 

10 fasteners per minute @ 90 psi

 

Trigger

 

 

Air inlet: 1/4 inch NPT

 

 

 

 

 

 

 

MAGAZINE CAPACITY:

 

 

 

 

100+ Fasteners per Load

 

 

 

 

BRADS: 3/8 inch to 2 inch, 18 gauge

 

 

 

 

FINISH NAILS: 3/4 inch to 2-1/2 inch, 16 gauge

Magazine

 

Latch

Staples: 1/2 inch to 1-5/8 inch;

 

16 gauge

Button

 

Rail

Nail Slot

 

1/4 inch crown

Adjustable

 

 

 

 

WEIGHT: 5 lbs. 7 oz.

Depth Control

 

 

 

 

 

 

 

LENGTH: 12-3/4 inches

Quick

 

 

 

Clear

 

 

 

HEIGHT: 12 inches

 

 

 

Nose

 

 

 

MAXIMUM PRESSURE:

 

 

 

 

120 psi

Work Contact

18 gauge Nail Ribs

 

 

PRESSURE RANGE:

Element (WCE)

 

 

 

 

 

 

 

Magazine

 

60 psi – 120 psi

 

 

 

 

Fastener Discharge Area

 

 

 

 

 

 

www.chpower.com

2

Operating Instructions

 

SB660000

Important Safety Instructions

Never use

Always assume the

(Continued)

gasoline

tool contains

or other flammable liquids

fasteners. Respect the tool as a working

Tool Use and Care

to clean the tool. Never use

implement; no horseplay. Always keep

a.

Use clamps or another practical way

the tool in the presence of

others at a safe distance from the work

 

to secure and support the workpiece

flammable liquids or gases. Vapors

area in case of accidental discharge of

 

could ignite by a spark and cause an

fasteners. Do not point the tool toward

 

to a stable platform. Holding the

 

yourself or anyone whether it contains

 

explosion which will result in death or

 

work by hand or against the body is

fasteners or not. Accidental triggering

 

serious personal injury.

 

unstable and is able to lead to loss

Do

of the tool could result in death or

 

serious personal injury.

 

of control.

 

not

Do

b. Do not force the tool. Use the

remove, tamper with,

not

or otherwise cause the

 

correct tool for the application. The

drive a fastener on top

 

trigger lock or trigger

 

correct tool will do the job better

of other fasteners. The

 

to become inoperable.

 

and safer at the rate for which the

fastener could glance

 

Do not operate any

 

and cause death or a

 

tool is designed.

tool which has been modified in a like

 

serious puncture wound.

c.

Do not use the tool if the switch

fashion. Death or serious personal

 

injury could result.

! WARNING

 

does not turn the tool on or off. Any

 

 

 

Do

Do not operate or allow

 

tool that cannot be controlled with

 

not

anyone else to operate

 

the switch is dangerous and must be

 

touch the trigger unless

the tool if any warnings

 

repaired.

 

driving fasteners. Never

or warning labels are not legible.

d.

Disconnect the

attach air line to tool or

Warnings or warning labels are located

carry tool while touching the trigger.

on the tool magazine and body.

 

tool from the air

 

The tool could eject a fastener which

Do not drop or

 

source before making adjustments,

 

will result in death or serious personal

 

doing tool maintenance, clearing

throw the tool.

 

injury. Also actuate the trigger lock to

 

jams, leaving work area,loading,

Dropping or throwing the tool can

 

the safe position when not in use.

 

or unloading the tool. Such

result in damage that will make the tool

 

 

 

precautionary measures reduce the

 

unusable or unsafe. If the tool has been

 

risk of injury to persons.

 

dropped or thrown, examine the tool

 

Always disconnect the

closely for bent, cracked or broken parts

e.

Store the tool when it is idle out

and air leaks. STOP and repair before

tool from the power

 

of reach of children and other

using or serious injury could occur.

 

source when unattended, performing

 

untrained persons. A tool is

any maintenance or repair, clearing

Avoid using the

 

dangerous in the hands of untrained

a jam, or moving the tool to a new

tool when the

 

users.

location. Do not load the tool with

magazine is empty. Accelerated wear on

 

fasteners when the trigger is depressed.

the tool may occur.

 

 

f.

Maintain the tool with care. Keep

The tool could eject a fastener causing

Clean and check all

 

a cutting tool sharp and clean. A

death or serious personal injury.

 

air supply hoses

 

 

 

properly maintained tool, with sharp

 

and fittings before connecting the

 

cutting edges reduces the risk of

Always fit tool with a

tool to an air supply. Replace any

 

binding and is easier to control.

damaged or worn hoses or fittings.

 

fitting or hose coupling

 

Tool performance or durability may be

 

 

g.

Check for misalignment or binding

on or near the tool in

reduced.

 

of moving parts, breakage of parts,

such a manner that all

 

 

compressed air in the tool is discharged

Service

 

and any other condition that affects

 

at the time the fitting or hose coupling

 

a. Tool service must be performed only

 

the tool’s operation. If damaged,

is disconnected. Do not use a check

 

have the tool serviced before using.

valve or any other fitting which allows

by qualified repair personnel.

 

Many accidents are caused by poorly

air to remain in the tool. Death or

b. When servicing a tool, use only

 

serious personal injury could occur.

 

maintained tools. There is a risk of

Never

identical replacement parts. Use

 

bursting if the tool is damaged.

only authorized parts.

 

place

 

 

 

h.

Use only those fasteners listed

hands or any other body

c. Use only the lubricants supplied

 

in the Accessories section of this

parts in the fastener

with the tool or specified by the

 

discharge area of the tool.

 

manual. Fasteners not identified

manufacturer.

 

The tool might eject a fastener and

 

for use with this tool by the tool

could result in death or serious personal

Do not make any

 

manufacturer are able to result in

injury.

modifications to

 

a risk of injury to persons or tool

Never

the tool without first obtaining written

 

damage when used in this tool.

carry

approval from Campbell Hausfeld. Do

i.

Select an appropriate tool actuation

the tool by the air hose

not use the tool if any shields or guards

or pull the hose to move

are removed or altered. Do not use the

 

system, taking into consideration the

the tool or a compressor.

tool as a hammer. Personal injury or

 

work application for which the tool

Keep hoses away from

tool damage may occur.

 

is used.

heat, oil and sharp

 

 

edges. Replace any hose

 

 

 

 

 

 

that is damaged, weak or

 

 

 

worn. Personal injury or

 

 

 

tool damage could occur.

 

 

 

3

www.chpower.com

Operating Instructions

 

 

 

 

SB660000

Important Safety Instructions

 

 

Recommended Hookup

 

(Continued)

 

Use only a pressure-regulated

The illustration below shows the

 

Disconnect air

 

recommended hookup for the tool.

 

compressed air source to limit 120 psi

supply and release

 

 

 

the air pressure supplied to

1.

The air compressor

60 psi

tension from the pusher before

 

 

the tool. The regulated pressure must

 

 

must be able to

Min.

attempting to clear jams because

 

 

 

not exceed 120 psi. If the regulator

 

 

 

120 psi

fasteners can be ejected from the front

 

maintain a minimum

fails, the pressure delivered to the

 

of the tool. Personal injury may occur.

 

of 60 psi when the

Max.

tool must not exceed 200 psi. The tool

 

 

Air Source

 

could explode which will cause death or

 

tool is being used. An inadequate air

 

serious personal injury.

 

supply can cause a loss of power and

a. Never connect to an air source that

 

 

 

 

 

Save These Instructions

 

inconsistent driving.

 

is capable of exceeding 200 psi.

 

 

 

 

Do Not Discard

2.

An oiler can be

 

Over pressurizing the tool is able

 

 

 

 

 

used to provide oil

 

to result in bursting, abnormal

 

 

 

 

 

 

Operating Instructions

 

circulation through

 

operation, breakage of the tool or

 

 

serious injury to persons. Use only

Lubrication

 

the tool. A filter can

 

 

be used to remove

 

clean, dry, regulated compressed air

 

 

 

 

 

 

This tool requires lubrication before

 

liquid and solid impurities which can

at the rated pressure or within the

 

using the tool for the first time and

 

rust or “gum up” internal parts of

rated pressure range as marked on

 

before each use. If an inline oiler is

 

the tool.

 

the tool. Always verify prior to using

 

 

used, manual lubrication through the

 

 

 

the tool that the air source has been

3.

Always use air supply hoses with

air inlet is not required on a daily basis.

adjusted to the rated air pressure or

 

a minimum working pressure

 

 

The work surface

 

 

within the rated air-pressure range.

 

 

rating equal to or greater than the

b. Never use oxygen, carbon dioxide,

 

can become

 

pressure from the power source if a

damaged by excessive lubrication.

 

 

regulator fails, or 150 psi, whichever

combustible gases or any bottled

Proper lubrication is the owner’s

 

 

is greater. Use 1/4 inch air hose for

gas as an air source for the tool.

responsibility. Failure to lubricate the

 

Such gases are capable of explosion

tool properly will dramatically shorten

 

runs up to 50 feet. Use 3/8 inch or

the life of the tool and void your

 

greater air hoses for 50 foot run or

and serious injury to persons.

 

 

 

warranty.

 

longer.

 

 

 

 

 

 

 

 

 

 

 

 

 

1.

Disconnect the air

 

 

 

Do not use any type of

O CO2

 

supply from the tool

 

150 psi or greater

 

reactive gases, including, but

 

 

to add lubricant.

 

 

 

not limited to, oxygen and

 

2.

Turn the tool so the

4.

Use a pressure regulator on the

combustible gases, as a power source.

 

air inlet is facing up.

 

compressor, with an operating

Use filtered, lubricated, regulated

 

 

 

 

 

Place 4-5 drops of

 

pressure of 0 psi - 125 psi. A pressure

compressed air only. Use of a reactive

 

 

gas instead of compressed air may

 

30 W non-detergent

 

regulator is required to control

cause the tool to explode which will

 

oil into air inlet. Do

 

the operating pressure of the tool

cause death or serious personal injury.

 

not use detergent

 

between 60 psi and 120 psi.

 

 

 

 

 

 

oils, oil additives, or airtool oils. Air tool oils contain solvents which will damage the tool's internal components.

3. After adding oil, run tool briefly. Wipe off any excess oil from the cap exhaust.

Minimum Recommended Hookup

 

Quick

 

Quick Plug

Coupler

Quick Plug

Quick

Coupler

Air Hose

www.chpower.com

4

Operating Instructions

 

 

SB660000

Operating Instructions

5.

Depress the WCE

3a. For 18 gauge nails, insert a stick

(Continued)

 

against the work

of Campbell Hausfeld nails or

Operational Mode - Single Cycle

 

surface without

equivalent (see “Fasteners” section)

 

pulling the trigger.

into the magazine against the

Always know the

 

 

The tool must not

ribs. Make sure the pointed ends

operational mode of

 

the tool before using. Failure to know

 

operate. Do not use the tool if it

of the fasteners are resting on the

the operational mode could result in

 

operates without pulling the trigger.

bottom ledge of the magazine when

death or serious personal injury.

 

Personal injury may result.

loading. Make sure the nails are not

 

 

This tool requires the trigger to be

6. Remove the tool from

dirty or damaged.

pulled each time a nail is driven. The

 

 

the work surface.

 

nailer can be actuated by depressing the

 

 

 

The WCE must return

 

Work Contact Element (WCE) against

 

 

 

to its original down

 

the work surface followed by pulling

 

 

 

position. The tool

 

the trigger.

 

 

 

must not operate. Do not use the

 

 

 

 

The trigger must be released to reset

 

tool if it operates while lifted from

 

the tool before another nail can be

 

the work surface. Personal injury

 

driven.

 

may result.

 

 

7.

Pull the

3b. For 16 gauge nails, insert the nail

 

 

trigger

 

 

points down into the slot next to the

 

 

and

 

 

rail.

 

 

depress

 

 

 

 

 

the WCE

 

 

 

against

 

Work contact element (WCE)

 

the work surface. The tool MUST

 

 

NOT operate.

 

Check the operation

 

 

8.

Depress

 

of the Work Contact

 

Element (WCE) trip mechanism before

 

the WCE

 

each use. The WCE must move freely

 

against

 

without binding through its entire

 

Magazine Rail

 

the work

travel distance. The WCE spring must

 

 

 

surface.

 

return the WCE to its fully extended

 

3c. For staples, load a clip of staples

 

Pull the

position after being depressed. Do

 

with the crowns straddling the

not operate the nailer if the WCE trip

 

trigger. The tool MUST operate.

 

magazine rail.

mechanism is not operating properly.

 

 

 

An improperly

 

Personal injury may occur.

 

 

 

functioning tool

 

1. Disconnect the air

 

 

must not be used. Do not actuate the

 

supply from the tool.

tool unless the tool is placed firmly

 

 

against the work piece.

 

2.

Remove all fasteners

Loading/Unloading The Nailer

 

 

from the magazine

1. Always disconnect the tool from the

 

 

(see Loading/

 

air supply before loading fasteners.

 

 

Unloading).

2.

Push

Latch

Magazine Rail

 

 

 

3.

Make sure the trigger

 

down on

Button

4. Push the magazine cover forward

 

and WCE move freely

 

the latch

 

until latch button pops up.

 

up and down without

 

button.

 

 

 

sticking or binding.

 

Pull back

 

 

4.

Reconnect air supply

 

on the

 

 

 

magazine

 

 

 

to the tool.

 

 

 

 

 

cover.

 

 

 

 

 

 

 

5. Always unload all fasteners before removing tool from service. Unloading is the reverse of loading, except that you must disconnect the air supply before unloading.

5

www.chpower.com

Operating Instructions

SB660000

Operating Instructions (Continued)

Adjusting the Fastener Penetration

The tool is equipped with an adjustable depth of drive feature. This allows the user to determine how deep a fastener will be driven into the work surface.

1. Adjust operating pressure so nails

 

are driven consistently. Do not

 

exceed 120 psi.

 

2.

To drive the

 

 

nail shallower,

 

 

turn the

 

 

wheel (C)

(C)

 

to right to

 

 

 

the extent

 

 

desired.

 

3. To sink a nail

 

 

deeper, turn

 

 

the wheel

 

 

(C) to left to

 

 

the extent

 

 

desired.

 

4.Make sure

trigger and WCE move freely up and down without binding or sticking after each adjustment.

Adjusting The Direction Of The

Exhaust

The tool is equipped

 

with an adjustable

 

direction exhaust

 

deflector. This is

 

intended to allow

Rotate

the user to change

 

the direction of the exhaust. Simply twist the deflector to any direction desired.

User - Maintenance Instructions

Clearing A Jam From The Tool

1. Disconnect the air supply from the nailer.

2. Remove

all nails from the

magazine (see Loading/

Unloading). Failure to do so will cause the nails to eject from the front of the tool.

3. Undo latch by pulling out and down. The wire latch will disengage

from the hooks on the nose.

4. The door can now be rotated, exposing the jammed fastener.

5. Remove the jammed fastener, using pliers or a screwdriver if required.

6 Rotate door back into the closed position.

7. Extend the wire latch and place over the hooks on the nose.

8. Close the latch by pushing the latch up and in until the latch snaps into place.

9. Make sure the trigger and WCE move freely up and down without sticking or binding.

Technical Service

Please call our Tool Hotline at 1-800- 543-6400 with any questions regarding the operation or repair of this tool or for additional copies of this manual.

Fastener And Replacement Parts

Use only genuine Campbell Hausfeld

18 gauge fasteners (or equivalent - see Fastener Interchange Information). Tool performance, safety and durability could be reduced if improper fasteners are used. When ordering replacement parts or fasteners, specify by part number.

Tool Repair

Only qualified personnel should repair the tool and they should use genuine Campbell Hausfeld replacement parts and accessories, or parts and accessories which perform equivalently.

Assembly Procedure For Seals

When repairing a tool, the internal parts must be cleaned and lubricated. Parker O-lube or equivalent must be used on all o-rings. Each o-ring must be coated with O-lube before assembling. A small amount of oil must be used on all moving surfaces and pivots. After reassembling, a few drops of 30W non-detergent oil or equivalent, must be added through the air line before testing.

Storage

The tool should be stored in a cool dry place.

www.chpower.com

6

Operating Instructions

SB660000

Fasteners

18 gauge Brad Nails

The following Campbell Hausfeld Brad nails are available at local retail stores. For help locating any item, call customer service at 1-800-543-6400. Campbell Hausfeld nails meet or exceed ASTM Standard F1667.

 

 

 

 

 

 

Nails Per

Nails Per

Model

Length

Shank Gauge

Finish

Head

Collation

Stick

Box

FB180016

5/8 inch

18 Gauge

Galvanized

Brad / Brown

Adhesive

100

1000

FB180025

1 inch

18 Gauge

Galvanized

Brad / Brown

Adhesive

100

1000

FB180030

1-1/4 inch

18 Gauge

Galvanized

Brad / Brown

Adhesive

100

1000

FB180040

1-1/2 inch

18 Gauge

Galvanized

Brad / Brown

Adhesive

100

1000

FB180050

2 inch

18 Gauge

Galvanized

Brad / Brown

Adhesive

100

1000

This tool drives most brands of brad nails with these specifications:

Length: 3/8 inch to 2 inch

Gauge: 18

16 gauge Finish Nails

The following Campbell Hausfeld finishing nails are available at local retail stores. If you need help locating any item, call customer service at 1-800-543-6400. Campbell Hausfeld nails meet or exceed ASTM Standard F1667.

 

 

 

 

 

 

Nails Per

Nails Per

Model

Length

Shank Gauge

Finish

Head

Collation

Stick

Box

FB160025

1”

16 Gauge

Galvanized

Brad

Adhesive

50

1000

FB160040

1-1/2”

16 Gauge

Galvanized

Brad

Adhesive

50

1000

FB160050

2”

16 Gauge

Galvanized

Brad

Adhesive

50

1000

FB160065

2-1/2”

16 Gauge

Galvanized

Brad

Adhesive

50

1000

This tool drives most brands of finish nails with these specifications:

Length: 3/4 inch to 2-1/2 inch

Gauge: 16

7

www.chpower.com

Operating Instructions

SB660000

Fasteners

Crown staples

The following Campbell Hausfeld staples are available at local retail stores. If you need help locating any item, call customer service at 1-800-543-6400. Campbell Hausfeld staples meet or exceed astm Standard F1667.

 

 

Wire

Crown

 

 

 

Staples

Staples

Model

Length

Diameter

Size

Point

Finish

Collation

Per Stick

Per Box

FN180615

1/2 inch

18 Gauge

1/4 inch

Chisel

Galvanized / Vinyl Coated

Adhesive

100

1000

FN180620

3/4 inch

18 Gauge

1/4 inch

Chisel

Galvanized / Vinyl Coated

Adhesive

100

1000

FN180625

1 inch

18 Gauge

1/4 inch

Chisel

Galvanized / Vinyl Coated

Adhesive

100

1000

FN180630

1-1/4 inch

18 Gauge

1/4 inch

Chisel

Galvanized / Vinyl Coated

Adhesive

100

1000

This tool drives most brands of 1/4 inch crown staples with these specifications:

Length: 1/2 inch to 1-5/8 inch

Gauge: 18

www.chpower.com

8

+ 24 hidden pages