Campbell Hausfeld IN734500AV, CHN10610 User Manual

4.84 Mb
Loading...

See Warranty on page 8 for important information about commercial use of this product.

Operating Instructions

CHN10610

 

 

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference.

Upholstery Stapler

Table of Contents

Descripion . . . . . . . . . . . . . . . . . . . . . . .1 Unpacking . . . . . . . . . . . . . . . . . . . . . . .1 Safety Guidelines . . . . . . . . . . . . . . . . .1 Important Safety Information . . . . . . .1

Tool Components and

Specifications . . . . . . . . . . . . . . . . . . . . .2 Operating Instructions . . . . . . . . . . . . .4 Lubrication . . . . . . . . . . . . . . . . . . . . .4 Recommended Hookup . . . . . . . . . . .4 Operational Mode . . . . . . . . . . . . . . .5 Trigger Only Mode . . . . . . . . . . . . . . .5 Loading/Unloading The Tool . . . . . . .5 Adjusting Direction of Exhaust . . . . .5 Clearing A Jam From The Tool . . . . .5 User-Maintenance Instructions . . . . . .5 Fasteners . . . . . . . . . . . . . . . . . . . . . . . .5 Troubleshooting Chart .. .. .. .. .. .. .. .. .. .. .. .. ..6 Warranty . . . . . . . . . . . . . . . . . . . . . . . .8

Description

This stapler is designed for upholstery, crafts, and tacking.. Features include: adjustable exhaust, narrow nose for fitting in tight spaces, rubber comfort grip and a trigger lock..

Unpacking

After unpacking the unit, inspect carefully for any damage that may have occurred during transit.. Make sure to tighten fittings, bolts, etc.., before putting unit into service..

Safety Guidelines

This manual contains information that is very important to know and understand.. This information is provided for SAFETY and to PREVENT EQUIPMENT PROBLEMS.. To help

recognize this information, observe the following symbols..

Danger indicates an imminently

hazardous situation which, if not avoided, WILL result in death or serious injury.

Warning indicates a potentially

hazardous situation which, if not avoided, COULD result in death or serious injury.

Caution indicates a potentially

hazardous situation which, if not avoided, MAY result in minor or moderate injury.

Notice indicates important

information, that if not followed, may cause damage to equipment.

NOTE: Information that requires special attention..

Important Safety Instructions

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS

When using tools, basic precautions should always be followed, including

the following:

Model CHN10610

Locate model and date code on tool and record below:

Model No..: _____________________

Date Code: _____________________

Retain these numbers for future reference..

California proposition 65

This product or

its power cord may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Wash hands after handling.

You can create dust when you cut, sand, drill or grind

materials such as wood,

paint, metal, concrete, cement, or other masonry. This dust often contains chemicals known to cause cancer, birth defects, or other reproductive harm. Wear protective gear.

REMINDER: Keep your dated proof of purchase for warranty purposes!

Attach it to this manual or file it for safekeeping.

Campbell Hausfeld Tools meet or exceed Industries’ Standards as set forth by the American National Standard

IN734500AV 5/10

Institute/International Staple, Nail and Tool Association in ANSI/ISANTA SNT-101-2002..

 

© 2010 Campbell Hausfeld/Scott Fetzer

For parts, product & service information

 

visit www.chpower.com

Operating Instructions

Important Safety Instructions

c..

Keep bystanders, children, and

 

e..

Use safety equipment. A dust mask,

(Continued)

 

visitors away while operating the

 

 

non-skid safety shoes and a hard

General

 

tool. Distractions are able to result in

 

hat must be used for the applicable

 

the loss of control of the tool..

 

 

conditions..

 

a..

To reduce the risks of

 

 

 

 

 

 

 

f..

Always wear eye

 

 

electric shock, fire, and

Personal Safety

 

 

 

injury to persons, read all

a..

Stay alert. Watch what you are

 

 

protection.

 

 

 

g..

Always wear hearing

 

 

the instructions before

 

doing and use common sense

 

 

 

using the tool.

 

when operating the tool. Do not

 

 

protection when using

 

 

 

 

 

 

the tool. Prolonged

 

b.

Be thoroughly familiar with the

 

use the tool while tired or under

 

 

 

 

controls and the proper use of the

 

the influence of drugs, alcohol,

 

 

exposure to high intensity

 

 

equipment.. Follow all instructions..

 

or medication. A moment of

 

 

noise is able to cause

 

 

Contact your Campbell Hausfeld

 

inattention while operating the

 

 

hearing loss..

 

 

representative if you have any

 

tool increases the risk of injury to

 

h..

Do not attach the hose or tool to

 

questions..

 

persons..

 

 

your body. Attach the hose to the

c.

Only persons well acquainted with

b..

Dress properly. Do not wear loose

 

 

structure to reduce the risk of loss of

 

these rules of safe operation should

 

clothing or jewelry. Contain long

 

 

balance if the hose shifts..

 

 

be allowed to use the unit..

 

hair. Keep hair, clothing, and

 

i..

Always assume that the tool

 

Read and

 

gloves away from moving parts.

 

 

contains fasteners. Do not point

 

understand tool

 

Loose clothes, jewelry, or long

 

 

the tool toward yourself or anyone

labels and manual. Failure to follow

 

hair increases the risk of injury to

 

 

whether it contains fasteners or not..

warnings, dangers, and cautions could

 

 

 

 

persons as a result of being caught

 

j.

Do not nail on

result in DEATH or SERIOUS INJURY.

 

 

 

in moving parts..

 

Work Area

 

 

 

top of another

c..

Avoid unintentional starting.

 

 

nail. This is able to cause the nail to

 

 

 

 

be deflected and hit someone, or

a..

Keep the work area clean and well

 

Be sure the switch is off before

 

 

 

 

 

cause the tool to react and result in a

 

lighted. Cluttered benches and dark

 

connecting to the air supply. Do not

 

 

 

 

risk of injury to persons.

 

 

areas increase the risks of electric

 

carry the tool with your finger on

 

k..

Remove finger

 

shock, fire, and injury to persons..

 

the switch or connect the tool to th

 

 

 

from the trigger

 

 

 

air supply with the switch on..

 

 

b..

Do not operate the tool

 

 

 

when not driving fasteners. Never

 

in explosive atmospheres,

d..

Do not overreach. Keep proper

 

 

carry the tool with finger on trigger,

 

such as in the presence

 

footing and balance at all times.

 

 

the tool is able to fire a fastener.

 

 

 

 

Activate the trigger lock when not in

 

of flammable liquids,

 

Proper footing and balance enables

 

 

 

 

use.

 

 

gases, or dust. The tool is

 

better control of the tool in

 

 

Always remain in a

 

able to create sparks resulting in the

 

unexpected situations..

 

 

 

 

 

 

firmly balanced

 

ignition of the dust or fumes..

 

 

 

 

 

 

 

 

position when using or handling the

 

 

 

 

 

tool.

 

Tool Components and Specifications

Adjustable Cap Exhaust

 

Requires: 0..15 average SCFM with 10

 

 

 

 

 

 

 

fasteners per minute @ 90 psi

 

 

 

 

 

 

Air inlet: 1/4 inch NPT

 

 

 

 

 

Latch

STAPLE SIZE RANGE: 1/4 inch to 9/16 inch

 

 

 

Trigger

Lever

MAGAZINE CAPACITY: 100+ Arrow® T50® staples or

 

 

Lock

 

 

equivalent (see Fastener Section)

 

 

 

 

Magazine

 

 

 

 

 

 

 

 

WEIGHT: 2 lbs.., 1 oz..

 

 

 

 

 

 

LENGTH: 8-1/2 inch

 

 

 

 

 

 

HEIGHT: 5-5/8 inch

 

Trigger

 

 

 

 

 

 

 

 

 

 

MAXIMUM PRESSURE: 100 psi

 

Fastener Discharge Area

 

PRESSURE RANGE: 60 psi – 100 psi

 

 

 

 

 

 

 

 

www.chpower.com

 

 

 

 

 

 

2

CHN10610

Important Safety Instructions (Continued)

Avoid long extended periods of work

with the tool. Stop using the tool if you feel pain in hands or arms.

Tool Use and Care

a..Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against the body is unstable and is able to lead to loss of control..

b..Do not force the tool. Use the correct tool for the application.. The correct tool will do the job better and safer at the rate for which the tool is designed..

c..Do not use the tool if the switch does not turn the tool on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired..

d.

 

 

 

Disconnect the

 

 

 

 

 

 

 

 

 

 

tool from the air

 

 

 

 

 

 

 

 

 

source before making adjustments,

 

doing tool maintenance, clearing

 

jams, leaving work area,loading,

 

or unloading the tool. Such

 

precautionary measures reduce the

risk of injury to persons..

e..Store the tool when it is idle out of reach of children and other untrained persons. A tool is

dangerous in the hands of untrained users..

f..Maintain the tool with care. A properly maintained tool reduces the risk of problems and is easier to control..

g..Check for misalignment or binding of moving parts, breakage of parts, and any other condition that affects the tool’s operation. If damaged, have the tool serviced before using.. Many accidents are caused by poorly maintained tools.. There is a risk of bursting if the tool is damaged..

h..Use only those fasteners listed in the Accessories section of this manual. Fasteners not identified for use with this tool by the tool manufacturer are able to result in a risk of injury to persons or tool damage when used in this tool..

i.Selecting an appropriate tool actuation system, taking into consideration the work application for which the tool is used..

Never use

gasoline or other flammable liquids to clean the tool. Never use

the tool in the presence of flammable liquids or gases. Vapors could ignite by a spark and cause an

explosion which will result in death or serious personal injury.

Do not remove, tamper with, or otherwise cause the trigger lock or trigger

to become inoperable. Do not operate any tool which has been modified in a like fashion. Death or serious personal injury could result.

Do not

touch the trigger unless driving fasteners. Never attach air line to tool or

carry tool while touching the trigger. The tool could eject a fastener which will result in death or serious personal injury. Also actuate the trigger lock to the safe position when not in use.

Always disconnect the tool from the power source when unattended,

performing any maintenance or repair, clearing a jam, loading, unloading or moving the tool to a new location. Do not load the tool with fasteners when the trigger is depressed. The tool could eject a fastener causing death or serious personal injury.

Always fit tool with a fitting near the tool in such a manner that all

compressed air in the tool is discharged at the time the fitting is disconnected. Do not use a check valve or any other fitting which allows air to remain in the tool. Death or serious personal injury could occur.

Never place hands or any other body parts in the fastener discharge area of

the tool. The tool might eject a fastener and could result in death or serious personal injury.

Never carry the tool by the air hose or pull the hose to move the tool or

a compressor. Keep hoses away from heat, oil and sharp edges. Replace any

hose that is damaged, weak or worn. Personal injury or tool damage could occur.

Always assume the tool contains

fasteners. Respect the tool as a working implement; no horseplay. Always keep others at a safe distance from the work area in case of accidental discharge of fasteners. Do not point the tool toward yourself or anyone whether it contains fasteners or not. Accidental triggering of the tool could result in death or serious personal injury.

! WARNING

Do not operate or allow anyone else to operate the tool if any warnings or warning labels are not legible. Warnings or warning labels are located on the tool magazine and body.

Do not drop or throw the tool.

Dropping or throwing the tool can result in damage that will make the tool unusable or unsafe. If the tool has been dropped or thrown, examine the tool closely for bent, cracked or broken parts and air leaks. STOP and repair before using or serious injury could occur.

Avoid using the tool when the

magazine is empty. Accelerated wear on the tool may occur.

Clean and check all air supply hoses

and fittings before connecting the tool to an air supply. Replace any damaged or worn hoses or fittings. Tool performance or durability may be reduced.

Service

a..Tool service must be performed only by qualified repair personnel.

b..When servicing a tool, use only identical replacement parts. Use only authorized parts.

www.chpower.com

3

60 psi Min.
100 psi Max.

Operating Instructions

Important Safety Instructions

 

 

1.

Disconnect the air

 

(Continued)

 

O CO2

 

supply from the tool

 

Do not use any type of

 

to add lubricant..

 

c.. Use only the lubricants supplied

 

 

 

reactive gases, including, but

 

 

 

 

with the tool or specified by the

 

 

 

 

not limited to, oxygen and

 

 

 

 

manufacturer.

 

2.

Turn the tool so the air

 

combustible gases, as a power source.

OIL

Do not make any

Use filtered, lubricated, regulated

 

inlet is facing up.. Place

 

modifications to

compressed air only. Use of a reactive

 

4-5 drops of 30 W non-

 

the tool without first obtaining written

gas instead of compressed air may

 

detergent oil into air inlet..

 

approval from Campbell Hausfeld. Do

cause the tool to explode which will

 

Do not use detergent

 

not use the tool if any shields or guards

cause death or serious personal injury.

 

 

 

oils, oil additives, or airtool oils..

are removed or altered. Do not use the

 

 

 

 

 

 

Air tool oils contain solvents which

tool as a hammer. Personal injury or

 

 

 

tool damage may occur.

Use only a pressure-regulated

 

 

will damage the tool's internal

Disconnect air

100 psi

 

components..

 

compressed air source to limit

 

 

supply and release

 

 

 

 

the air pressure supplied to

 

3.

After adding oil, run

 

tension from the pusher before

 

 

the tool. The regulated pressure must

 

tool briefly.. Wipe off

 

attempting to clear jams because

 

 

not exceed 100 psi. If the regulator

 

 

 

any excess oil from the

 

fasteners can be ejected from the front

 

 

fails, the pressure delivered to the

 

 

of the tool. Personal injury may occur.

 

cap exhaust..

 

tool must not exceed 200 psi. The tool

 

 

Air Source

could explode which will cause death or

Recommended Hookup

 

serious personal injury.

 

 

 

 

 

 

 

a..Never connect to an air source that is capable of exceeding 200 psi.

Over pressurizing the tool is able to result in bursting, abnormal operation, breakage of the tool or serious injury to persons.. Use only clean, dry, regulated compressed air at the rated pressure or within the rated pressure range as marked on

the tool.. Always verify prior to using the tool that the air source has been adjusted to the rated air pressure or within the rated air-pressure range..

b..Never use oxygen, carbon dioxide, combustible gases or any bottled gas as an air source for the tool.

Such gases are capable of explosion and serious injury to persons..

Save These Instructions

Do Not Discard

Operating Instructions

Lubrication

This tool requires lubrication before using the tool for the first time and before each use.. If an inline oiler is used, manual lubrication through the air inlet is not required on a daily basis..

The work surface can become

damaged by excessive lubrication. Proper lubrication is the owner’s responsibility. Failure to lubricate the tool properly will dramatically shorten the life of the tool and void your warranty.

The illustration below shows the recommended hookup for the tool..

1. The air compressor must be able to

maintain a minimum of 60 psi when the

tool is being used.. An inadequate air supply can cause a loss of power and inconsistent driving..

2. An oiler can be used to provide oil circulation through the tool.. A filter can

be used to remove liquid and solid impurities which can rust or “gum up” internal parts of the tool..

Recommended Hookup

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Quick

 

 

Regulator

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Quick

Quick Plug

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Coupler

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Quick Plug

 

 

 

Coupler

(Optional)

(Optional)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Air Hose

Lubricator

Filter

www.chpower.com

4

CHN10610

Operating Instructions (Continued)

3.Always use air supply hoses with a minimum working pressure rating equal to or greater than the pressure from the power source if a regulator fails, or 150 psi, whichever is greater.. Use 1/4 in.. air hose for runs up to 50 ft.. Use 3/8 in.. air hoses for 50 ft.. run or longer.. For better performance, install a 3/8 in.. quick plug (1/4 in.. NPT threads) with an inside diameter of

..315 in.. (8mm) on the tool and a 3/8 in.. quick coupler on the air hose..

150 psi or greater

3/8 inch I..D..

4.Use a pressure regulator on the compressor, with an operating pressure of 0 psi - 125 psi.. A pressure regulator is required to control

the operating pressure of the tool between 60 psi and 100 psi..

Operational Mode

Always know the operational mode of

the tool before using. Failure to know the operational mode could result in death or serious personal injury.

Trigger Only Mode (with Trigger LOCK)

The tool is a single-actuator device.. This mode requires that, with the trigger lock not positioned in the safe mode, only a pull of the trigger will fire a fastener..

After verifying there are no fasteners in the tool, safety check the operation of the activated trigger lock to prevent the tool from firing a fastener before storage.. Always disconnect from

compressed air when not in use..

LOADING/UNLOADING THE TOOL

1.Always disconnect the tool from the air supply before loading fasteners..

2.

Turn stapler upside

 

 

down and pull the

 

 

latch.. Pull back on the

 

 

magazine cover..

 

3. Insert a stick of

 

 

Arrow® T50® staples

 

 

or equivalent (see

 

 

Fastener Section) into the magazine

 

with the crown side down.. Make

 

sure the staples are not dirty or

 

damaged..

 

4.

Push the magazine

 

 

cover forward until

 

 

the latch catches..

 

5.

Always unload all

 

 

fasteners before

 

 

removing tool from

 

 

service.. Unloading

 

 

is the reverse of

 

 

loading, except always disconnect

 

the air hose before unloading..

Adjusting The Direction Of The

Exhaust

 

The tool is

 

equipped with

 

an adjustable

Rotate

direction exhaust

 

deflector.. This is intended to allow the user to change the direction of the exhaust.. Simply twist the deflector to any direction desired..

Clearing A Jam From The Tool

1. Disconnect the air supply from the tool..

2.Remove all fasteners from the magazine (see "Loading/ Unloading The Tool")..

3.With the magazine open, remove the jammed fastener, using pliers, a screwdriver or a pick if required..

4.Close magazine..

User-Maintenance Instructions

Technical Service

Please call our Tool Hotline at 1-800- 543-6400 with any questions regarding the operation or repair of this tool or for additional copies of this manual..

Fastener And Replacement Parts

Use only Arrow® T50® or equivalent staples.

Tool performance, safety and durability could be reduced if improper fasteners are used. When ordering replacement parts or fasteners, specify by part number.

Tool Repair

Only qualified personnel should repair the tool and they should use genuine Campbell Hausfeld replacement parts and accessories, or parts and accessories which perform equivalently..

Assembly Procedure For Seals

When repairing a tool, the internal parts must be cleaned and lubricated.. Parker O-lube or equivalent must be used on all o-rings.. Each o-ring must be coated with O-lube before assembling.. A small

amount of oil must be used on all moving surfaces and pivots.. After reassembling, a few drops of 30W non-detergent oil or equivalent, must be added through the air line before testing..

Storage

The stapler should be stored in a cool dry place..

Fasteners

Fasteners used in this stapler include:

Arrow® T50® staples or any equivalent fastener with the approximate dimensions illustrated below..

1/4 inch - 9/16 inch

6mm - 14mm 1..3mm

10..7mm

9..3mm

0..7mm

www.chpower.com

5

Operating Instructions

Troubleshooting Chart

Stop using tool immediately if any of the following problems occur. Serious personal injury could occur. Any repairs or replacements must be done by a Qualified Service Person or Authorized Service Center.

Symptom

Possible Cause(s)

Corrective Action

Air leaking at trigger valve

O-Rings in trigger valve housing are

Replace o-rings

area..

damaged

 

 

 

 

 

 

Air leaking between housing

1. Damaged O-Rings

1.

Replace o-rings

and nose..

2.

Damage to bumper

2.

Replace bumper

 

 

 

 

 

 

Air leaking between housing

1.

Loose screws

1.

Tighten screws

and cap..

2.

Damaged gasket

2.

Replace gasket

 

 

 

 

 

 

Tool skips driving fastener

1.

Worn bumper

1.

Replace bumper

 

2.

Dirt in nose piece

2.

Clean drive channel

 

3.

Dirt or damage prevent fasteners or

3.

Clean magazine

 

 

pusher from moving freely in magazine

 

 

 

4.

Damaged pusher spring

4.

Replace spring

 

5.

Inadequate air flow to tool

5.

Check fitting, hose, or compressor

 

6.

Worn O-Ring on piston or lack of

6.

Replace and lubricate o-rings

 

 

lubrication

 

 

 

7.

Damaged O-Ring on trigger valve

7.

Replace o-rings

 

8.

Air leaks

8.

Tighten screws and fittings

 

9.

Cap gasket leaking

9.

Replace gasket

 

 

 

 

 

Tool runs slow or has loss of

1.

Tool not lubricated sufficiently

1.

Lubricate tool

power

2.

Broken spring in cylinder cap

2.

Replace spring

 

 

3.

Exhaust port in cap is blocked

3.

Replace damaged internal parts

 

 

 

 

Fasteners are jammed in tool

1. Guide on driver is worn

1.

Replace guide

 

2.

Fasteners are not correct size

2.

Use only recommended fasteners

 

3.

Fasteners are bent

3.

Replace with undamaged fasteners

 

4.

Magazine or nose screws are loose

4.

Tighten screws

 

5.

Driver is damaged

5.

Replace driver

www.chpower.com

6

+ 18 hidden pages