Campbell Hausfeld CHN20102, IN703201AV User Manual

1.86 Mb
Loading...

See Warranty on page 8 for important information about commercial use of this product.

Operating Instructions

CHN20102

 

 

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference.

Finishing Nailer

Table of Contents

Description . . . . . . . . . . . . . . . . . . . . . 1

Unpacking . . . . . . . . . . . . . . . . . . . . . . 1

Safety Guidelines . . . . . . . . . . . . . . . . 1

Important Safety Information . . . . . . 1

Tool Components and

Specifications. . . . . . . . . . . . . . . . . . . . 2

Operating Instructions . . . . . . . . . . . . 4

Lubrication . . . . . . . . . . . . . . . . . . . . 4

Recommended Hookup. . . . . . . . . . 4

Operational Mode . . . . . . . . . . . . . . 5

Work Contact Element (WCE) . . . . . 5

Loading/Unloading The Tool. . . . . . 5

Adjusting the Nail Penetration. . . . 5

Adjusting the Direction

of the Exhaust . . . . . . . . . . . . . . . . . 5

User-Maintenance Instructions . . . . . 6

Clearing A Jam From The Tool . . . . 6

Technical Service . . . . . . . . . . . . . . . 6

Fastener And Replacement Parts . . 6

Tool Repair . . . . . . . . . . . . . . . . . . . . 6

Assembly Procedure For Seals. . . . . 6

Fastener Interchange Information. . . 6

Troubleshooting Chart . . . . . . . . . . . . 7

Warranty . . . . . . . . . . . . . . . . . . . . . . . 8

Description

This nailer is designed for decorative trim, molding, window casings, furniture trim and picture frame assembly. Features include: convenient rear loading magazine which holds up to 100 nails, no-mar tip, adjustable

exhaust, single cycle trigger, quick clear nose, and an adjustable depth of drive mechanism.

Unpacking

After unpacking the unit, inspect carefully for any damage that may have occurred during transit. Make sure to tighten fittings, bolts, etc., before putting unit into service.

Safety Guidelines

This manual contains information that is very important to know and understand. This information is provided for SAFETY and to PREVENT EQUIPMENT PROBLEMS. To help

recognize this information, observe the following symbols.

Danger indicates an imminently

hazardous situation which, if not avoided, WILL result in death or serious injury.

Warning indicates a potentially

hazardous situation which, if not avoided, COULD result in death or serious injury.

Caution indicates a potentially

hazardous situation which, if not avoided, MAY result in minor or moderate injury.

Notice indicates important

information, that if not followed, may cause damage to equipment.

NOTE: Information that requires special attention.

Model CHN20102

Locate model and date code on tool and record below:

Model No.: _____________________

Date Code: _____________________

Retain these numbers for future reference.

When using tools, basic precautions should always be followed, including

the following:

CALIFORNIA PROPOSITION 65

This product or

its power cord may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.

Important Safety Instructions

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS

You can create dust when you cut, sand, drill or grind

materials such as wood,

paint, metal, concrete, cement, or other masonry. This dust often contains chemicals known to cause cancer, birth defects, or other reproductive harm. Wear protective gear.

REMINDER: Keep your dated proof of purchase for warranty purposes!

Attach it to this manual or file it for safekeeping.

Campbell Hausfeld Nailers meet or exceed Industries’ Standards as set forth by the American IN703201AV 8/09 National Standard Institute/International Staple, Nail and Tool Association in ANSI/ISANTA

SNT-101-2002.

© 2009 Campbell Hausfeld/Scott Fetzer

For parts, product & service information

visit www.chpower.com

 

Operating Instructions

 

 

 

 

 

 

 

 

 

CHN20102

Important Safety Instructions

PERSONAL SAFETY

g.

Always wear hearing

 

 

 

 

(Continued)

a.

Stay alert. Watch what you are

 

protection when using

 

 

GENERAL

 

doing and use common sense

 

the tool. Prolonged

 

 

 

 

exposure to high intensity

 

 

a.

To reduce the risks of

 

 

when operating the tool. Do not

 

 

 

 

electric shock, fire, and

 

 

use the tool while tired or under

 

noise is able to cause

 

 

 

 

hearing loss.

 

 

 

the influence of drugs, alcohol,

 

 

injury to persons, read all

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

or medication. A moment of

h. Do not attach the hose or tool to

 

the instructions before

 

 

 

 

 

inattention while operating the

 

your body. Attach the hose to the

 

using the tool.

 

 

b. Be thoroughly familiar with the

 

tool increases the risk of injury to

 

structure to reduce the risk of loss of

 

persons.

 

balance if the hose shifts.

 

controls and the proper use of the

 

 

 

b.

Dress properly. Do not wear loose

i. Always assume that the tool

 

equipment. Follow all instructions.

 

Contact your Husky representative if

 

clothing or jewelry. Contain long

 

contains fasteners. Do not point

 

you have any questions.

 

hair. Keep hair, clothing, and

 

the tool toward yourself or anyone

c.

Only persons well acquainted with

 

gloves away from moving parts.

 

whether it contains fasteners or not.

 

Loose clothes, jewelry, or long

j.

 

 

 

 

 

 

 

 

these rules of safe operation should

 

 

 

 

 

Do not nail on

 

 

hair increases the risk of injury to

 

 

 

 

 

be allowed to use the unit.

 

 

 

 

 

 

top of another

 

 

persons as a result of being caught

 

nail. This is able to cause the nail to

 

 

Read and

 

 

 

 

 

in moving parts.

 

be deflected and hit someone, or

 

 

understand tool

 

 

 

 

 

 

 

 

 

cause the tool to react and result in a

labels and manual. Failure to follow

c.

Avoid unintentional starting.

 

 

risk of injury to persons.

warnings, dangers, and cautions could

 

Be sure the switch is off before

k.

 

 

 

 

Remove finger

result in DEATH or SERIOUS INJURY.

 

connecting to the air supply. Do not

 

 

 

 

 

 

 

 

 

 

from the trigger

 

 

 

 

 

 

 

 

 

 

WORK AREA

 

carry the tool with your finger on

 

 

 

 

 

 

 

when not driving fasteners. Never

a.

Keep the work area clean and well

 

the switch or connect the tool to the

 

carry the tool with finger on trigger,

 

air supply with the switch on.

 

the tool is able to fire a fastener.

 

lighted. Cluttered benches and dark

 

 

 

d.

Do not overreach. Keep proper

 

 

 

 

Always remain in a

 

areas increase the risks of electric

 

 

 

 

 

 

 

 

 

firmly balanced

 

shock, fire, and injury to persons.

 

footing and balance at all times.

 

 

 

 

 

 

position when using or handling the

 

 

 

 

 

Proper footing and balance enables

b.

Do not operate the tool

 

 

tool.

 

 

 

 

better control of the tool in

 

in explosive atmospheres,

 

 

 

 

 

 

Avoid long extended

 

 

 

unexpected situations.

 

 

 

 

 

such as in the presence of

 

 

 

 

 

 

periods of work

 

 

 

 

 

 

 

 

 

 

 

flammable liquids, gases,

 

e. Use safety equipment. A dust mask,

with the tool. Stop using the tool if you

 

 

feel pain in hands or arms.

 

or dust. The tool is able to create

 

non-skid safety shoes and a hard

 

 

 

 

 

 

 

 

 

 

 

sparks resulting in the ignition of

 

hat must be used for the applicable

 

 

 

 

 

 

 

 

 

the dust or fumes.

 

conditions.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

c.

Keep bystanders, children, and

f.

Always wear eye

 

 

 

 

 

 

 

 

 

 

 

visitors away while operating the

 

protection.

 

 

 

 

 

 

 

 

 

 

 

tool. Distractions are able to result in

 

 

 

 

 

 

 

 

 

 

 

 

 

the loss of control of the tool.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Tool Components and Specifications

REQUIRES: 0.7 SCFM with

10nails per minute @ 90 psi

AIR INLET: 1/4 inch NPT

NAIL SIZE RANGE:

1inch to 2-1/2 inch

MAGAZINE CAPACITY:

100Nails per Load, 16 gauge

WEIGHT: 4 lbs. 8 oz.

LENGTH: 12.5 inches

HEIGHT: 11.5 inches

MAXIMUM PRESSURE:

110psi

PRESSURE RANGE:

70psi – 110 psi

Nail Discharge Area

 

 

 

Cap Exhaust

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Latch

 

Button

 

Area

Trigger

Loading

Adjustment

 

Nail Length

Nail

Switch

 

 

Magazine

www.chpower.com

2

Operating Instructions

 

CHN20102

Important Safety Instructions

Never use

Always assume the

(Continued)

gasoline

tool contains

or other flammable liquids

fasteners. Respect the tool as a working

TOOL USE AND CARE

to clean the tool. Never use

implement; no horseplay. Always keep

a.

Use clamps or another practical way

the tool in the presence of

others at a safe distance from the work

 

to secure and support the workpiece

flammable liquids or gases. Vapors

area in case of accidental discharge of

 

could ignite by a spark and cause an

fasteners. Do not point the tool toward

 

to a stable platform. Holding the

 

yourself or anyone whether it contains

 

explosion which will result in death or

 

work by hand or against the body is

fasteners or not. Accidental triggering

 

serious personal injury.

 

unstable and is able to lead to loss

 

of the tool could result in death or

 

 

serious personal injury.

 

of control.

 

 

 

 

b. Do not force the tool. Use the

Do not remove, tamper

 

 

correct tool for the application. The

with, or otherwise cause

Do not drive a fastener

 

the trigger lock or trigger

 

correct tool will do the job better

on top of other

 

to become inoperable. Do not operate

 

and safer at the rate for which the

fasteners. The fastener

 

any tool which has been modified in a

 

could glance and cause death or a

 

tool is designed.

like fashion. Death or serious personal

 

serious puncture wound.

c.

Do not use the tool if the switch

injury could result.

 

 

! WARNING

 

does not turn the tool on or off. Any

 

 

 

Do not operate or allow

 

tool that cannot be controlled with

Do not touch the trigger

 

the switch is dangerous and must be

anyone else to operate

 

unless driving fasteners.

the tool if any warnings

 

repaired.

 

Never attach air line to

or warning labels are not legible.

d.

Disconnect the

tool or carry tool while touching the

Warnings or warning labels are located

trigger. The tool could eject a fastener

on the tool magazine and body.

 

tool from the air

 

which will result in death or serious

Do not drop or

 

source before making adjustments,

 

doing tool maintenance, clearing

personal injury. Also actuate the trigger

throw the tool.

 

jams, leaving work area,loading,

lock to the safe position when not in

Dropping or throwing the tool can

 

or unloading the tool. Such

use.

result in damage that will make the tool

 

precautionary measures reduce the

 

unusable or unsafe. If the tool has been

 

risk of injury to persons.

 

dropped or thrown, examine the tool

e.

Store the tool when it is idle out

Always disconnect the

closely for bent, cracked or broken parts

and air leaks. STOP and repair before

tool from the power

 

of reach of children and other

using or serious injury could occur.

 

source when unattended,

 

untrained persons. A tool is

Avoid using the

 

performing any maintenance or repair,

 

dangerous in the hands of untrained

clearing a jam, or moving the tool to a

tool when the

 

users.

new location. Do not load the tool with

magazine is empty. Accelerated wear on

 

fasteners when the trigger is depressed.

the tool may occur.

f.

Maintain the tool with care. Keep

The tool could eject a fastener causing

Clean and check all

 

a cutting tool sharp and clean. A

death or serious personal injury.

 

air supply hoses

 

properly maintained tool, with sharp

 

 

 

and fittings before connecting the

 

cutting edges reduces the risk of

Always fit tool with a

tool to an air supply. Replace any

 

binding and is easier to control.

damaged or worn hoses or fittings.

 

fitting or hose coupling

Tool performance or durability may be

g.

Check for misalignment or binding

on or near the tool in

reduced.

 

of moving parts, breakage of parts,

such a manner that all compressed air

SERVICE

 

and any other condition that affects

in the tool is discharged at the time the

 

fitting or hose coupling is disconnected.

 

 

the tool’s operation. If damaged,

a. Tool service must be performed only

 

Do not use a check valve or any other

 

have the tool serviced before using.

fitting which allows air to remain in the

by qualified repair personnel.

 

Many accidents are caused by poorly

tool. Death or serious personal injury

b. When servicing a tool, use only

 

could occur.

 

maintained tools. There is a risk of

identical replacement parts. Use

 

 

 

bursting if the tool is damaged.

 

only authorized parts.

h.

Use only those fasteners listed

Never place hands or any

c. Use only the lubricants supplied

 

in the Accessories section of this

other body parts in the

with the tool or specified by the

 

manual. Fasteners not identified

fastener discharge area of

manufacturer.

 

the tool. The tool might eject a fastener

 

for use with this tool by the tool

Do not make any

 

and could result in death or serious

 

manufacturer are able to result in

 

personal injury.

modifications

 

a risk of injury to persons or tool

 

to the tool without first obtaining

 

damage when used in this tool.

 

written approval from Husky. Do not

i.

Selecting an appropriate tool

Never carry the tool by

use the tool if any shields or guards are

removed or altered. Do not use the tool

the air hose or pull the

 

actuation system, taking into

as a hammer. Personal injury or tool

 

hose to move the tool

 

consideration the work application

damage may occur.

 

or a compressor. Keep hoses away from

 

for which the tool is used.

heat, oil and sharp edges. Replace any

 

 

 

hose that is damaged, weak or worn.

 

 

 

Personal injury or tool damage could

 

 

 

occur.

 

 

 

3

www.chpower.com

Operating Instructions

 

 

 

 

 

 

CHN20102

Important Safety Instructions

 

 

 

RECOMMENDED HOOKUP

 

(Continued)

 

 

Use only a pressure-regulated

 

The illustration below shows the

 

Disconnect air

 

 

 

recommended hookup for the tool.

 

 

compressed air source to limit

110 psi

supply and release

the air pressure supplied to

 

 

 

 

1.

The air compressor

70 psi

tension from the pusher before

 

 

the tool. The regulated pressure must

 

 

 

must be able to

Min.

attempting to clear jams because

 

 

not exceed 110 psi. If the regulator

 

 

 

 

110 psi

fasteners can be ejected from the front

fails, the pressure delivered to the

 

maintain a minimum

 

Max.

of the tool. Personal injury may occur.

tool must not exceed 200 psi. The tool

 

of 70 psi when the

 

 

AIR SOURCE

 

 

could explode which will cause death or

 

tool is being used. An inadequate air

 

 

serious personal injury.

 

 

supply can cause a loss of power and

a. Never connect to an air source that

 

 

 

 

 

 

 

SAVE THESE INSTRUCTIONS

 

inconsistent driving.

 

is capable of exceeding 200 psi.

 

 

 

 

 

 

DO NOT DISCARD

 

2. An oiler can be

 

Over pressurizing the tool is able

 

 

 

 

 

 

 

to result in bursting, abnormal

 

 

Operating Instructions

 

 

used to provide oil

 

operation, breakage of the tool or

 

 

circulation through

 

 

 

 

 

 

serious injury to persons. Use only

LUBRICATION

 

 

the tool. A filter can

 

clean, dry, regulated compressed air

This tool requires lubrication before

 

be used to remove liquid and solid

at the rated pressure or within the

using the tool for the first time and

 

impurities which can rust or “gum

rated pressure range as marked on

before each use. If an inline oiler is

 

up” internal parts of the tool.

 

the tool. Always verify prior to using

used, manual lubrication through the

3. Always use air supply hoses with

the tool that the air source has been

air inlet is not required on a daily basis.

 

a minimum working pressure

 

adjusted to the rated air pressure or

 

The work surface

 

rating equal to or greater than the

within the rated air-pressure range.

 

 

pressure from the power source if a

 

can become

 

 

b. Never use oxygen, carbon dioxide,

damaged by excessive lubrication.

 

regulator fails, or 150 psi, whichever

combustible gases or any bottled

Proper lubrication is the owner’s

 

is greater. Use 1/4 inch air hose for

responsibility. Failure to lubricate the

 

gas as an air source for the tool.

 

 

runs up to 50 feet. Use 3/8 inch or

 

tool properly will dramatically shorten

 

Such gases are capable of explosion

 

greater air hoses for 50 foot run or

the life of the tool and void your

 

and serious injury to persons.

 

 

warranty.

 

 

longer.

 

 

 

 

1.

Disconnect the air

 

 

150 psi or greater

 

 

 

 

 

supply from the tool

 

 

 

Do not use any type of

O

 

 

 

 

 

 

CO2

 

to add lubricant.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

reactive gases, including, but

 

 

 

 

 

4.

Use a pressure regulator on the

not limited to, oxygen and

 

 

2.

Turn the tool so the

 

 

compressor, with an operating

combustible gases, as a power source.

 

 

 

air inlet is facing up. Place

OIL

 

pressure of 0 - 125 psi. A pressure

Use filtered, lubricated, regulated

 

 

 

 

 

 

 

 

 

compressed air only. Use of a reactive

 

4-5 drops of 30 W non-

 

 

regulator is required to control

gas instead of compressed air may

 

 

detergent oil into air inlet.

 

 

the operating pressure of the tool

cause the tool to explode which will

 

Do not use detergent

 

 

between 70 and 110 psi.

 

cause death or serious personal injury.

oils, oil additives, or airtool oils. Air tool oils contain solvents which will damage the tool's internal components.

3. After adding oil, run tool briefly. Wipe off any excess oil from the cap exhaust.

Recommended Hookup

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Regulator

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Quick

 

 

 

 

Quick Plug

Quick

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Coupler

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Quick Plug

 

Coupler

 

 

 

 

(Optional)

(Optional)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Air Hose

Lubricator

Filter

www.chpower.com

4

Operating Instructions

 

 

 

 

 

 

CHN20102

Operating Instructions

 

6.

Remove the nailer

 

 

ADJUSTING THE NAIL PENETRATION

(Continued)

 

 

 

from the work

 

 

The tool is equipped with an adjustable

OPERATIONAL MODE - SINGLE CYCLE

 

surface. The Work

 

 

depth of drive feature. This allows the

 

Contact Element

 

 

 

Always know the

 

 

 

user to determine how deep a fastener

 

 

(WCE) must return to

 

 

 

operational mode of

 

 

 

will be driven into the work surface.

 

 

its original down position. The nailer

the tool before using. Failure to know

 

1. Adjust operating pressure so nails

the operational mode could result in

 

MUST NOT OPERATE. Do not use

 

are driven consistently. Do not

death or serious personal injury.

 

 

the tool if it operates while lifted

 

 

 

 

 

exceed 110 psi.

 

This tool requires the

 

 

 

from the work surface. Personal

 

 

 

 

2. To drive the nail shallower, turn

trigger to be pulled

 

 

 

injury may result.

 

 

each time a nail is

 

 

7.

Pull the trigger

 

 

the wheel (C) to right to the extent

driven. The nailer

1

2

 

 

desired.

 

 

and depress the

 

 

 

can be actuated by

 

 

 

 

 

 

 

 

 

 

work contact

 

 

 

 

depressing the WCE against the work

 

1

2

 

 

 

element (WCE)

 

 

surface followed by pulling the trigger.

 

 

 

 

 

 

against the work surface. The nailer

(C)

 

 

 

 

 

 

 

The trigger must be released to reset

 

MUST NOT OPERATE.

 

 

 

 

the tool before another nail can be

8.

Depress the Work

 

 

 

 

driven.

 

 

 

 

 

 

 

 

 

Contact Element

 

 

 

 

 

 

 

 

 

 

 

 

 

WORK CONTACT ELEMENT (WCE)

 

(WCE) against

1

2

 

 

 

the work surface.

 

 

 

 

 

 

 

 

 

 

Check the operation

 

 

 

 

 

 

 

Pull the trigger. The nailer MUST

 

 

 

of the Work Contact

 

3. To sink a nail deeper, turn the wheel

Element (WCE) trip mechanism before

 

OPERATE.

 

 

 

 

 

(C) to left to the extent desired.

each use. The WCE must move freely

 

An improperly

 

 

 

 

 

without binding through its entire

 

 

 

4. Make sure trigger and

 

 

 

functioning tool

 

travel distance. The WCE spring must

must not be used. Do not actuate the

work contact element

 

return the WCE to its fully extended

tool unless the tool is placed firmly

(WCE) move freely up

 

position after being depressed. Do

 

 

 

against the work piece.

 

 

and down without

 

not operate the nailer if the WCE trip

 

 

 

 

 

 

 

 

 

 

 

 

binding or sticking after

mechanism is not operating properly.

LOADING/UNLOADING THE NAILER

Personal injury may occur.

 

 

1. Always disconnect the tool from the

each adjustment.

 

1.

Disconnect the air

 

 

 

 

 

 

 

air supply before loading fasteners.

ADJUSTING THE DIRECTION OF THE

 

supply from the

 

 

2. Insert nails into rear slot as shown.

EXHAUST

 

 

nailer.

 

 

 

 

 

 

 

 

 

 

 

The tool is equipped

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

with an adjustable

 

2.

Remove all nails

 

 

 

 

 

 

direction exhaust

 

 

from the magazine

 

 

 

 

 

 

deflector. This is

Rotate

 

(see Loading/

 

 

 

 

 

 

intended to allow

 

 

 

 

 

 

 

 

 

Unloading).

 

 

 

 

 

 

the user to change the direction of the

 

 

 

 

 

 

 

 

exhaust. Simply twist the deflector to

3. Make sure the trigger

 

 

 

 

 

 

any direction desired.

 

 

and work contact

 

 

 

 

 

 

 

 

 

element (WCE) move

 

 

3. Pull pusher back until it is behind

 

 

 

freely up and down

 

 

 

nail clip, then release.

 

 

 

 

 

without sticking or

 

 

4. Always unload all fasteners before

 

 

 

binding.

 

 

 

 

 

 

 

 

removing tool from service.

 

 

 

 

 

 

 

 

 

 

 

4.

Reconnect air

 

 

 

Unloading is the reverse of loading,

 

 

 

supply to the

 

 

 

except always disconnect the air

 

 

 

nailer.

 

 

 

hose before unloading.

 

 

 

 

5.

Depress the Work

 

 

 

 

 

 

 

 

 

Contact Element

 

 

 

 

 

 

 

 

 

(WCE) against the

 

 

 

 

 

 

 

 

 

work surface without

 

 

 

 

 

 

 

 

 

pulling the trigger.

 

 

 

 

 

 

 

 

 

The nailer MUST NOT OPERATE.

 

 

 

 

 

 

 

Do not use the tool if it operates

 

 

 

 

 

 

 

without pulling the trigger. Personal

 

 

 

 

 

 

 

injury may result.

 

 

 

 

 

 

 

 

5

www.chpower.com

Operating Instructions

 

 

 

 

 

 

 

CHN20102

User - Maintenance

TECHNICAL SERVICE

 

 

ASSEMBLY PROCEDURE FOR SEALS

Instructions

Please call our Tool Hotline at 1-800-

When repairing a tool, the internal

CLEARING A JAM FROM THE TOOL

543-6400 with any questions regarding

parts must be cleaned and lubricated.

1.

Disconnect the air

the operation or repair of this tool or

Parker O-lube or equivalent must be

for additional copies of this manual.

used on all o-rings. Each o-ring must be

 

supply from the

 

 

 

 

 

coated with O-lube before assembling.

 

tool.

FASTENER AND REPLACEMENT

 

 

 

A small amount of oil must be used on

 

 

PARTS

 

 

 

 

 

 

 

 

all moving surfaces and pivots. After

 

 

 

Use only headless

2.

Remove all nails

 

reassembling, a few drops of 30W

 

 

micropins, 16 gauge.

 

 

non-detergent oil or equivalent, must

 

from the magazine

Tool performance, safety and durability

 

be added through the air line before

 

(see Loading/

could be reduced if improper fasteners

 

are used. When ordering replacement

testing.

 

 

 

 

Unloading). Failure

 

 

 

 

parts or fasteners, specify by part

 

 

 

 

 

 

 

to do so will cause

 

STORAGE

 

 

 

 

number.

 

 

 

 

 

 

 

the nails to eject from the front of

 

 

 

 

 

 

 

TOOL REPAIR

 

 

 

The tool should be stored in a cool dry

 

the tool.

 

 

 

 

 

 

 

place.

 

 

 

 

 

 

 

 

 

 

 

 

 

3.

Undo latch by

Only qualified personnel should repair

 

 

 

 

 

 

 

 

 

 

pulling out

the tool and they should use genuine

 

 

 

 

 

 

and down. The

Campbell Hausfeld replacement parts

 

 

 

 

 

 

wire latch will

and accessories, or parts and accessories

 

 

 

 

 

 

disengage from

which perform equivalently.

 

 

 

 

 

 

 

the hooks on the nose.

 

 

 

 

 

 

 

 

 

4.

The door can

 

 

 

 

 

 

 

 

 

 

now be rotated,

 

 

 

 

 

 

 

 

 

 

exposing the

 

 

 

 

 

 

 

 

 

 

jammed fastener.

 

 

 

 

 

 

 

 

 

5.

Remove the

 

 

 

 

 

 

 

 

 

 

jammed fastener,

 

 

 

 

 

 

 

 

 

 

using pliers or

 

 

 

 

 

 

 

 

 

 

a screwdriver if

 

 

 

 

 

 

 

 

 

 

required.

Fasteners

 

 

 

 

 

 

 

 

6.

Rotate door back

 

 

 

 

 

 

 

 

The following Campbell Hausfeld finishing nails are available at local retail stores.

 

into the closed

 

If you need help locating any item, call customer service at 1-800-543-6400.

 

 

position.

 

 

Campbell Hausfeld nails meet or exceed ASTM Standard F1667.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Nails

Nails

7.

Extend the wire

 

 

Shank

 

 

 

 

Per

Per

Model

Length

Gauge

Finish

Head

Collation

Stick

Box

 

latch and place

 

 

 

 

 

 

 

 

 

 

 

over the hooks on

FB005060

2

16

Galvanized

Brad

Adhesive

50

2500

 

the nose.

 

inch

Gauge

 

 

 

 

 

 

8.

Close the latch by

FB160025

1

16

Galvanized

Brad

Adhesive

50

1000

 

pushing the latch

 

inch

Gauge

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

up and in until the

FB160040

1-1/2

16

Galvanized

Brad

Adhesive

50

1000

 

latch snaps into

 

inch

Gauge

 

 

 

 

 

 

 

place.

FB160065

2-1/2

16

Galvanized

Brad

Adhesive

50

1000

9.

Make sure the

 

inch

Gauge

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

trigger and work

Interchange Information

 

 

 

 

 

 

 

contact element

 

 

 

 

 

 

 

(WCE) move freely

Nails used in the Campbell Hausfeld CHN201 Finishing Nailer will also work in

 

up and down

Hitachi NT65A, Paslode 3250-F16, IM250F, Duo Fast LFN-764, Sears 18321, Porter

 

without sticking or binding.

Cable FN200 and FN250.

 

 

 

 

 

 

www.chpower.com

6

Operating Instructions

CHN20102

Troubleshooting Chart

Stop using tool immediately if any of the following problems occur. Serious personal injury could occur. Any repairs or replacements must be done by a Qualified Service Person or Authorized Service Center.

Symptom

Possible Cause(s)

Corrective Action

Air leaking at trigger valve

O-rings in trigger valve housing are

Replace o-rings

area.

damaged

 

 

 

 

 

 

Air leaking between housing

1. Damaged o-rings

1.

Replace o-rings

and nose.

2.

Damage to bumper

2.

Replace bumper

 

 

 

 

 

Air leaking between housing

1. Loose screws

1.

Tighten screws

and cap.

2.

Damaged seal

2.

Replace seal

 

 

 

 

 

Tool skips driving fastener

1. Worn bumper

1.

Replace bumper

 

2.

Dirt in nose piece

2.

Clean drive channel

 

3.

Dirt or damage prevent fasteners or

3.

Clean magazine

 

 

pusher from moving freely in magazine

 

 

 

4.

Damaged pusher spring

4.

Replace spring

 

5.

Inadequate air flow to tool

5.

Check fitting, hose, or compressor

 

6.

Worn o-rings on piston or lack of

6.

Replace and lubricate o-rings

 

 

lubrication

 

 

 

7.

Damaged o-rings on trigger valve

7.

Replace o-rings

 

8.

Air leaks

8.

Tighten screws and fittings

 

9.

Cap seal leaking

9.

Replace seal

Tool runs slow or has loss of

1. Tool not lubricated sufficiently

1.

Lubricate nailer

power

2.

Broken spring in cylinder cap

2.

Replace spring

 

 

3.

Exhaust port in cap is blocked

3.

Replace damaged internal parts

Fasteners are jammed in tool

1. Guide on driver is worn

1.

Replace guide

 

2.

Fasteners are not correct size

2.

Use only recommended fasteners

 

3.

Fasteners are bent

3.

Replace with undamaged fasteners

 

4.

Magazine or nose screws are loose

4.

Tighten screws

 

5.

Driver is damaged

5.

Replace driver

 

 

 

Air leaking at trigger valve

O-rings or seals are damaged

Replace O-rings or seals

stem

 

 

 

 

7

www.chpower.com

Operating Instructions

CHN20102

Limited Warranty

1.DURATION: From the date of purchase by the original purchaser as follows: One (1) Year.

2.WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive, Harrison, Ohio, 45030, Telephone: (800) 543-6400

3.WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the Campbell Hausfeld product.

4.WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: Any Campbell Hausfeld nailer, stapler, air tool, spray gun, inflator or air accessory supplied or manufactured by Warrantor.

5.WHAT IS COVERED UNDER THIS WARRANTY: Substantial defects in material and workmanship which occur within the duration of the warranty period.

6.WHAT IS NOT COVERED UNDER THIS WARRANTY:

A.Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED FROM THE DATE OF ORIGINAL PURCHASE AS STATED IN THE DURATION. If this product is used for commercial, industrial or rental purposes, the warranty will apply for ninety (90) days from the date of purchase. Some States do not allow limitation on how long an implied warranty lasts, so the above limitations may not apply to you.

B.ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY DEFECT, FAILURE, OR MALFUNCTION OF THE CAMPBELL HAUSFELD PRODUCT. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

C.Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate products in accordance with instructions provided in the owner’s manual(s) supplied with product. Accident, purchaser's abuse, neglect or failure to operate products in accordance with instructions shall also include the removal or alteration of any safety devices. If such safety devices are removed or altered, this warranty is void.

D.Normal adjustments which are explained in the owner’s manual(s) provided with the product.

E.Items or service that are normally required to maintain the product, i.e. o-rings, springs, bumpers, debris shields, driver blades, fuses, batteries, gaskets, packings or seals, fluid nozzles, needles, sandblast nozzles, lubricants, material hoses, filter elements, motor vanes, abrasives, blades, cut-off wheels, chisels, chisel retainers, cutters, collets, chucks, rivet jaws, screw driver bits, sanding pads, back-up pads, impact mechanism, or any other expendable part not specifically listed. These items will only be covered for ninety (90) days from date of original purchase. Underlined items are warranted for defects in material and workmanship only.

7.RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s option, products or components which are defective, have malfunctioned and/or failed to conform within duration of the warranty period.

8.RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:

A.Provide dated proof of purchase and maintenance records.

B.Call Campbell Hausfeld (800) 543-6400 to obtain your warranty service options. Freight costs must be borne by the purchaser.

C.Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).

9.WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY: Repair or replacement will be scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of replacement parts.

This Limited Warranty applies in the United States, Canada and Mexico only and gives you specific legal rights. You may also have other rights which vary from state to state or country to country.

www.chpower.com

8

+ 16 hidden pages