Campbell Hausfeld IN626100AV, WX8019 User Manual

1.31 Mb
Loading...

See Warranty on page 6 for important information about commercial use of this product.

Operating Instructions

WX8019

 

 

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference.

Oilless Compressors

Description

Oilless compressors are designed for a variety of home tasks. These compressors can power smaller pneumatic tools, but work ideally for brad nailers, finishing nailers and staplers. These units operate without oil.

Safety Guidelines

This manual contains information that is very important to know and understand. This information is provided for SAFETY and to PREVENT EQUIPMENT PROBLEMS. To help recognize this information, observe the following symbols.

Danger indicates an imminently

hazardous situation which, if not avoided, will result in death or serious injury.

Warning indicates a potentially

hazardous situation which, if not avoided, COULD result in death or serious injury.

Caution indicates a potentially

hazardous situation which, if not avoided, MAY result in minor or moderate injury.

Notice indicates important

information, that if not followed, may cause damage to equipment.

Unpacking

After unpacking the unit, inspect carefully for any damage that may have occurred during transit. Make sure to tighten fittings, bolts, etc., before putting unit into service. In case of questions, damaged or missing parts, please call the nearest Maxus Authorized Service Center. Have the serial number, model number and parts list (with missing parts circled before calling).

DO NOT RETURN THE STOP! PRODUCT TO THE

RETAILER!

Do not operate unit if damaged

during shipping, handling or use. Damage may result in bursting and cause injury or property damage.

Record the Model and Serial numbers (located on the compressor) and the date of purchase in the spaces below.

Model No. ________________________

Serial No. ________________________

Date of purchase __________________

Retain these numbers for future reference.

CALIFORNIA PROPOSITION 65

You can

create dust when you cut, sand, drill or grind materials such as wood, paint, metal,

concrete, cement, or other masonry. This dust often contains

chemicals known to cause cancer, birth defects, or other reproductive harm. Wear protective gear.

This product or its power cord

contains lead, a chemical known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.

Breathable Air Warning

This compressor/pump is NOT equipped and should NOT be used “as is” to supply breathing quality air. For any application of air for human consumption, you must fit the air compressor/pump with suitable in-line safety and alarm equipment. This additional equipment is necessary to properly filter and purify the air to meet minimal specifications for Grade D breathing as described in Compressed Gas Association Commodity Specification G 7.1 - 1966, OSHA 29 CFR 1910. 134, and/or Canadian Standards Associations (CSA).

DISCLAIMER OF WARRANTIES IN THE EVENT THE COMPRESSOR IS USED FOR THE PURPOSE OF BREATHING AIR APPLICATION AND

PROPER IN-LINE SAFETY AND ALARM EQUIPMENT IS NOT SIMULTANEOUSLY USED, EXISTING WARRANTIES ARE VOID, AND THE MANUFACTURER DISCLAIMS ANY LIABILITY WHATSOEVER FOR ANY LOSS, PERSONAL INJURY OR DAMAGE.

General Safety

Information

OPERATIONAL SAFETY

Since the air compressor and other components (material pump, spray guns, filters, lubricators, hoses, etc.) used, make up a high pressure pumping system, the following safety precautions must be observed at all times:

1. Read all manuals included

with this product carefully. Be thoroughly familiar MANUAL with the controls and the

proper use of the equipment.

REMINDER: Keep your dated proof of purchase for warranty purposes!

Attach it to this manual or file it for safekeeping.

© 2009

IN626100AV 4/09

Oilless Compressors

General Safety

Information (cont.)

2.Follow all local electrical and safety codes, as well as in the U.S.A., National Electrical Codes (NEC) and Occupational Safety and Health Act (OSHA).

3.Only persons well acquainted with these rules of safe operation should be allowed to use the compressor.

4.Keep visitors away and NEVER allow children in the work area.

5.Wear safety glasses and use hearing protection when operating the pump or unit.

6.Do not stand on or use the pump or unit as a handhold.

7.Before each use, inspect compressed air system and electrical components for signs of damage, deterioration, weakness or leakage. Repair or replace defective items before using.

8.Check all fasteners at frequent intervals for proper tightness.

Motors, electrical equipment and controls can cause electrical

arcs that will ignite a flammable gas or vapor.

Never operate or repair in or near a flammable gas or vapor. Never store flammable liquids or gases in the vicinity of the compressor.

Compressor parts may be hot even if the unit is stopped.

9.Keep fingers away from a running compressor; fast moving and hot parts will cause injury and/or burns.

10.If the equipment should start to abnormally vibrate, STOP the engine/motor and check immediately for the cause. Vibration is generally a warning of trouble.

11.To reduce fire hazard, keep engine/motor exterior free of oil, solvent, or excessive grease.

Never remove or

attempt to adjust safety valve. Keep safety valve free from paint and other accumulations.

Never attempt

to repair or modify a tank! Welding, drilling or any other modification will weaken the tank resulting in damage

from rupture or explosion. Always replace worn or damaged tanks.

Drain liquid from tank daily.

12.Tanks rust from moisture build-up, which weakens the tank. Make sure to drain tank daily and inspect periodically for unsafe conditions such as rust formation and corrosion.

13.Fast moving air will stir up dust and debris which may be harmful. Release air slowly when draining moisture or depressurizing the compressor system.

SPRAYING PRECAUTIONS

Do not spray flammable materials in vicinity of open flame or near ignition sources including the compressor unit.

14.Do not smoke when spraying paint, insecticides, or other flammable substances.

15.Use a face mask /

respirator when spraying and spray in a well ventilated area to prevent health and fire hazards.

16.Do not direct paint or other sprayed material at the compressor. Locate compressor as far away from the spraying area as possible to minimize overspray accumulation on the compressor.

17.When spraying or cleaning with solvents or toxic chemicals, follow the instructions provided by the chemical manufacturer.

Installation

LOCATION

The tank must sit level or slope slightly towards the drain valve to allow the tank to drain properly. It is extremely important to install the compressor in a clean, well ventilated area where the surrounding air temperature will not be more than 40°C (104°F).

A minimum clearance of 0.1 meters

(4 inches) between the compressor and a wall is required because objects could obstruct air flow.

Do not locate the compressor air inlet

near steam, paint spray, sandblast areas or any other source of contamination. This debris will damage the motor.

ELECTRICAL INSTALLATION

All wiring and electrical

connections should be performed by a qualified electrician. Installation must be in accordance with local codes and national electrical codes.

GROUNDING INSTRUCTIONS

1.This product is for use on a nominal 240 volt circuit and has a grounding plug that looks like the plug illustrated in Figure 1. Make sure the product is connected to an outlet having the same configuration as the plug. This product must be grounded. In the event of an electrical short circuit, grounding reduces risk of electrical shock by providing an escape wire for electric current. This product is equipped with a cord having a grounding wire with an appropriate grounding plug. Cord must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Grounded

Outlet

Grounded Pin

Figure 1

Improper use of grounding plug can result in a possible risk of electrical shock!

2

 

 

 

 

 

WX8019

Installation (cont.)

Regulator

Tank Pressure

 

 

 

 

Do not use a

 

 

 

 

 

Gauge

 

grounding adapter

Outlet Pressure

 

 

with this product!

 

 

 

2. If repair or replacement of cord or

Gauge

 

 

 

 

 

plug is necessary, do not connect

 

 

 

grounding wire to either flat blade

 

 

Safety

terminal. The wire with insulation

 

 

Valve

having an external surface that is

 

 

 

green (with or without yellow

 

 

 

stripes) is the grounding wire.

 

 

 

 

Never connect

Tank

 

 

 

green (or green

 

 

 

 

 

 

and yellow) wire to a live terminal.

 

 

 

3. Check with a qualified electrician or

 

 

 

serviceman if grounding instructions

 

 

 

are not completely understood, or if

 

 

Quick connect

in doubt as to whether product is

 

 

coupler

 

 

 

properly grounded. Do not modify

Pump Shroud

 

 

 

 

 

plug provided; if it will not fit outlet,

Figure 2

 

 

have proper outlet installed by a

 

 

 

qualified electrician.

 

Glossary of Terms

 

MOISTURE IN COMPRESSED AIR

 

 

 

 

WIRING

 

 

Pressure Switch - Auto/Off Switch - In

 

Moisture in compressed air will form

1. Local electrical wiring codes differ

 

into droplets as it comes from an air

the AUTO position, the compressor

 

compressor pump. When humidity

from area to area. Source wiring,

 

shuts off automatically when tank

 

is high or when a compressor is in

plug and protector must be rated for

 

pressure reaches the maximum preset

 

continuous use for an extended

at least the amperage and voltage

 

 

period of time, this moisture will

pressure. In the OFF position, the

 

indicated on motor nameplate, and

 

collect in the tank. When using a

compressor will not operate. This

 

meet all electrical codes for this

 

paint sprayer, this water will be

switch should be in the OFF position

 

minimum.

 

 

 

carried from the tank through the

2. Use a slow blow fuse or a circuit

when connecting or disconnecting the

 

hose, and out of the gun as droplets

power cord from the electrical outlet or

 

mixed with the spray material.

breaker.

 

 

 

 

 

when changing air tools.

 

IMPORTANT: This condensation

 

 

 

 

Minimum Gauge of Extension Cord

Regulator - The regulator controls the

 

will cause water spots in a paint

 

job, especially when spraying other

 

 

 

amount of air pressure released at the

 

25 ft.

50 ft.

100 ft.

 

than water based paints. A filter in

hose outlet.

 

14

12

10

 

the air line (MP3105), located as

 

 

Use of an extension cord may cause

ASME Safety Valve - This valve

 

near to the gun as possible, will

automatically releases air if the tank

 

help eliminate this moisture.

excess heat to motor. This could lead

pressure exceeds the preset maximum.

 

 

to tripped breaker (at electrical

Reduce tank pressure below 10 psi by

Discharge Tube - This tube carries

panel) or tripped thermal overload

pulling the safety valve, then drain

(on compressor motor). If this occurs,

compressed air from the pump to the

moisture from tank. Drain daily to

eliminate extension cord and plug

check valve. This tube becomes very hot

avoid tank corrosion.

compressor directly into electrical

during use. To avoid the risk of severe

LUBRICATION

outlet. Avoid using extension cords;

burns, never touch the discharge tube.

use longer air hose(s) instead.

This is an oilless product and does not

Check Valve - One-way valve that

 

 

 

require lubrication to operate.

 

 

 

allows air to enter the tank, but

 

 

 

 

 

 

 

 

prevents air in the tank from flowing

 

 

 

 

 

back into the compressor pump.

 

 

Tank Drain - This valve is located on the bottom of the tank. Use this valve to drain moisture from the tank daily to reduce the risk of corrosion.

3

Figure 3

Oilless Compressors

Operation

ASME SAFETY VALVE

Do not remove or attempt to adjust

the safety valve!

This valve should be checked under pressure occasionally by pulling the ring by hand. If air leaks after

ring has been

released, or valve is stuck and cannot be actuated by ring, it MUST be replaced.

REGULATOR KNOB

1.This knob controls air pressure to an air operated tool, or paint spray gun.

2.Turning knob clockwise increases air pressure at outlet.

3.Turning counterclockwise will lower air pressure at outlet.

4.Fully counterclockwise will shut off flow of air completely.

OUTLET PRESSURE GAUGE

1.This gauge shows at-a-glance, air pressure at outlet. Air pressure is measured in bar [1 bar is equal to 14.5 pounds per square inch (psi)].

2.Be sure this gauge reads ZERO before changing air tools or disconnecting hose from outlet.

TANK PRESSURE GAUGE

Gauge shows pressure in tank indicating compressor is building pressure properly.

Maintenance

Disconnect power source then release all pressure from the system before attempting to install, service, relocate or perform any maintenance.

The compressor should be checked often for any visible problems and the following maintenance procedures should be performed each time the compressor is used.

1.Pull ring on safety valve and allow it to snap back to normal position.

Safety valve must be replaced if it

cannot be actuated or it leaks air after ring is released.

2.With compressor shut off and pressure released: Drain moisture from tank by opening drain valve underneath tank (See Figure 4).

Drain

Valve

Figure 4

3.Turn power OFF and clean dust and dirt from motor, tank, and air lines. IMPORTANT: Unit should be located as far from spraying area as hose will allow to prevent over-spray from clogging intake port.

THERMAL OVERLOAD PROTECTOR

This compressor is equipped with an

automatic reset thermal overload protector which will shut off motor if it becomes overheated.

If thermal overload protector shuts motor OFF frequently look for the following causes.

1.Low voltage.

2.Wrong gauge wire or length of extension cord.

3.Clogged air filter.

4.Lack of proper ventilation.

The motor must be allowed to cool

down before start-up is possible. The motor will automatically restart without warning if left plugged into electrical outlet, if the motor is turned on.

STORAGE

1.When not in use, store hose and compressor in a cool, dry place.

2.Drain tank of moisture

3.Disconnect hose and hang open ends down to allow any moisture to drain.

4

WX8019

Troubleshooting Chart

 

Symptom

Possible Cause(s)

Corrective Action

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Compressor will not run

1.

No electrical power

1.

Plugged in? Switch on? Check fuse/breaker

 

 

 

 

 

2.

Breaker open

2.

Reset, determine cause of problem

 

 

 

 

 

3.

Pressure switch bad

3.

Replace

 

 

 

 

 

4.

Motor over worked

4.

Turn off, let cool, turn on.

 

 

 

 

 

5. Tank pressure above cut-in

5.

Bleed tank pressure down to cut-in.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fuses blow/circuit breaker

1.

Incorrect size fuse, circuit overloaded

1.

Check for proper fuse, use time-delay fuse. Disconnect

 

 

 

 

trips repeatedly

 

 

 

 

other electrical appliances from circuit or operate

 

 

 

 

 

 

 

 

 

compressor on its own branch circuit

 

 

 

 

 

2.

Extension cord usage - wrong gauge wire

2.

Remove extension cord or refer to Extension Cord Chart on

 

 

 

 

 

 

and/or too long.

 

 

page 3

 

 

 

 

 

3.

Worn check valve

3.

Replace check valve

 

 

 

 

 

 

 

 

 

 

Do not disassemble check valve

 

 

 

 

 

 

 

 

 

 

with air in tank; bleed tank

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4.

Defective unloader valve (on pressure

4.

Replace unloader valve.

 

 

 

 

 

 

switch)

 

 

 

 

 

 

 

 

 

 

5.

Defective motor capacitor(s)

5.

Replace capacitor(s)

 

 

 

 

 

6.

Defective motor

6.

Replace motor

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Tank pressure drops when

1.

Loose connections (fittings, tubing, etc.)

1.

Check all connections with soap and water solution.

 

 

 

 

compressor shuts off

 

 

 

 

Tighten; or remove and apply pipe dope or pipe tape to the

 

 

 

 

 

2.

Open tank drain valve

 

 

threads, then reassemble.

 

 

 

 

 

 

 

2.

Close tank drain valve

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Air output lower than

1.

Excessive air usage

1.

Decrease air usage; compressor not large enough for air

 

 

 

 

normal/low discharge

 

 

 

 

requirement

 

 

 

 

pressure

2.

Clogged intake filter

2.

Clean or replace filter

 

 

 

 

 

3.

Open tank drain valve

3.

Close tank drain valve

 

 

 

 

 

4.

Air leaks in piping (on machine or in

4.

Check all connections with soap and water solution.

 

 

 

 

 

 

outside system)

 

 

Tighten; or remove and apply pipe dope or pipe tape to the

 

 

 

 

 

 

 

 

 

threads, then reassemble.

 

 

 

 

 

5.

Piston ring worn

5.

Replace piston and cylinder.

 

 

 

 

 

6.

Broken valve (in pump)

6.

Replace valve

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Excessive moisture in

1.

Excessive water in tank

1.

Drain tank

 

 

 

 

discharge air

2.

High humidity

2.

Move to area of less humidity; use air line filter

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Compressor runs

1.

Defective pressure switch

1.

Replace switch

 

 

 

 

continuously

2.

Excessive air usage

2.

Decrease air usage; compressor not large enough for air

 

 

 

 

 

 

 

 

 

requirement

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Motor hums but cannot

1.

Circuit overloaded

1.

Disconnect other electrical appliances from circuit or

 

 

 

 

run or runs slowly

 

 

 

 

operate compressor on its own branch circuit

 

 

 

 

 

2.

Extension cord usage - wrong gauge wire

2.

Remove extension cord or refer to Extension Cord Chart on

 

 

 

 

 

 

and/or too long.

 

 

page 3

 

 

 

 

 

3.

Loose electrical connections

3.

Check all electrical connections

 

 

 

 

 

4.

Worn check valve

4.

Replace check valve

 

 

 

 

 

 

 

 

 

 

Do not disassemble check valve

 

 

 

 

 

 

 

 

 

 

with air in tank; bleed tank

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5.

Defective unloader valve (on pressure

5.

Replace unloader valve

 

 

 

 

 

 

switch)

 

 

 

 

 

 

 

 

 

 

6.

Defective motor capacitor(s)

6.

Replace capacitor(s)

 

 

 

 

 

7.

Defective motor

7.Replace motor

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Thermal overload

1

Lack of proper ventilation / room

1.

Move compressor to well ventilated area

 

 

 

 

protector cuts out

 

temperature too high

 

 

 

 

 

 

 

 

 

repeatedly

2.

Clogged intake filter

2.

Clean or replace filter

 

 

 

 

 

3.

Circuit overloaded

3.

Check for proper fuse, use time-delay fuse. Disconnect

 

 

 

 

 

 

 

 

 

other electrical appliances from circuit or operate

 

 

 

 

 

 

 

 

 

compressor on its own branch circuit

 

 

 

 

 

4.

Extension cord usage - wrong gauge wire

4.

Remove extension cord or refer to Extension Cord Chart on

 

 

 

 

 

 

and/or too long.

 

 

page 3

 

 

 

 

 

5.

Worn check valve

5.

Replace check valve

 

 

 

 

 

 

 

 

 

 

Do not disassemble check valve

 

 

 

 

 

 

 

 

 

 

with air in tank; bleed tank

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6.

Defective unloader valve (on pressure

6.

Replace unloader valve.

 

 

 

 

 

 

switch)

 

 

 

 

 

 

 

 

 

 

7.

Defective motor

7.

Replace motor

 

 

 

 

 

 

 

 

 

 

 

 

 

5

Oilless Compressors

WX8019

 

 

Limited Warranty

1.DURATION: From the date of purchase by the original purchaser as follows: three years or five years, depending on the model.

2.WHO GIVES THIS WARRANTY (WARRANTOR): Maxus, 100 Production Drive, Harrison, Ohio, 45030

3.WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the Maxus product.

4.WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: Any Maxus air compressor, air tool or supplementary air accessory supplied or manufactured by Warrantor.

5.WHAT IS COVERED UNDER THIS WARRANTY: Defects due to material and workmanship with the exceptions noted below.

6.WHAT IS NOT COVERED UNDER THIS WARRANTY:

A.Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED FROM THE DATE OF ORIGINAL PURCHASE AS STATED IN THE DURATION. If this product is used for commercial, industrial or rental purposes, the warranty will apply for ninety (90) days from the date of purchase. Four cylinder single-stage and two-stage products are not limited to a ninety

(90)day warranty when used in commercial or industrial applications. Some States do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.

B.ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY DEFECT, FAILURE, OR MALFUNCTION OF THE PRODUCT. Some States do not allow the exclusion or limitations of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

C.Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate products in accordance with instructions provided in the owner’s manual(s) supplied with product.

D.Pre-delivery service, i.e. assembly, oil or lubricants, and adjustment.

E.Normal adjustments or expendable items which are explained in the owner’s manual(s) provided with the product including but not limited to belts and pressure switch.

F.Items or service that are normally required to maintain the product, i.e. lubricants, filters and gaskets, etc.

G.Gasoline engines and components are expressly excluded from coverage under this limited warranty. The Purchaser must comply with the warranty given by the engine manufacturer which is supplied with the product.

H.Additional items not covered under this warranty: 1. All Compressors

a.Any component damaged in shipment or any failure caused by installing or operating unit under conditions not in accordance with installation and operation guidelines.

b.Pump or valve failure caused by rain, excessive humidity or corrosive environments.

c.Cosmetic defects that do not interfere with compressor functionality.

d.Rusted tanks, including but not limited to rust due to improper drainage.

e.Electric motors and check valves after the first year of ownership.

f.Drain cocks.

g.Damage due to improper wiring.

h.Other items not listed but considered general wear parts.

2.Lubricated Compressors

a.Pump wear or valve damage caused by using oil not specified.

b.Pump wear or valve damage caused by any oil contamination or by failure to follow proper oil maintenance guidelines.

3.Belt Drive / Direct Drive / Gas Driven Compressors

a.Belts.

b.Ring wear from inadequate filter maintenance.

c.Manually adjusted load/unload and throttle control devices.

7.RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s option, products or components which are defective, have malfunctioned and/or failed to conform within duration of the warranty period.

8.RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:

A.Provide maintenance records to make warranty claim.

B.Portable products or components must be delivered or shipped to the nearest Maxus Authorized Service Center. Freight costs, if any, must be borne by the purchaser.

C.Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).

9.WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY:

A.Repair or replacement will be scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of replacement parts.

B.If the purchaser does not receive satisfactory results from the Authorized Service Center, the purchaser should contact the Maxus Product Service Department (see paragraph 2).

Limited Warranty applies in the U.S. and Canada only and gives you specific legal rights. You may also have other rights which vary from State to State or country to country.

6

Voir la Garantie à la page 12 pour de l’information importante sur l’utilisation commercial de ce produit.

Instructions D’Utilisation

WX8019

 

 

S’il vous plaît lire et conserver ces instructions. Lire attentivement avant de monter, installer, utiliser ou de procéder à l’entretien du produit décrit. Se protéger ainsi que les autres en observant toutes les instructions de sécurité, sinon, il y a risque de blessure et/ou dégâts matériels ! Conserver ces instructions comme référence.

Compresseur Sans Huile

Description

Les compresseurs sans huile sont conçus pour une variété de projets domestiques. Ces compresseurs peuvent actionner de petits outils pneumatiques, mais ils travaillent spécialement bien avec les cloueuses de pointes de vitrier, couleuses de finissage et les agrafeuses. Ces modèles fonctionnent sans huile.

Directives de Sécurité

Ce manuel contient de l’information très importante qui est fournie pour la SÉCURITÉ et pour ÉVITER LES PROBLÈMES D’ÉQUIPEMENT. Rechercher les symboles suivants pour cette information.

Danger indique une situation

hasardeuse imminente qui RÉSULTERA en perte de vie ou blessures graves.

Avertissement indique une

situation hasardeuse potentielle qui PEUT résulter en perte de vie ou blessures graves.

Attention indique une situation

hasardeuse potentielle qui PEUT résulter en blessures.

Avis indique de l’information

importante pour éviter le dommage de l’équipement.

Déballage

Lors du déballage de ce produit, l’examiner soigneusement pour rechercher toute trace de dommage susceptible de s’être produit en cours de transport. Veiller à serrer tout raccord, boulon, etc., avant de mettre ce produit en service. En cas de dommage ou de parties manquantes, S.V.P. composer le 1-888-MAXUS4U pour demander conseil ou appeler un Centre De Service Autorisé Maxus.

Prière d’avoir le numéro de série, numéro de modèle et liste de parties (avec les parties manquantes encerclées) avant d’appeler.

NE PAS RENVOYER LE ARRÊT! PRODUIT AU

MARCHAND!

Ne pas utiliser un modèle qui a été

endommagé pendant le transport, la manipulation ou l’utilisation. Le dommage peut résulter en explosion et peut causer des blessures ou dégâts matériels.

Enregistrer les numeros de Modele et de Serie (Situes sur le compresseur) et la date d’achat dans l’espace cidessous.

No. de Modèle _____________________

No. de Série

_____________________

Date d’Achat

_____________________

Garder ces numéros pour référence.

PROPOSITION 65 CALIFORNIE

Vous pouvez créer de la poussière en coupant,

ponçant, perçant ou meulant les matériaux tels que le bois, la peinture, le métal, le béton, le

ciment ou autre maçonnerie. Cette poussière contient souvent des produits chimiques reconnus pour causer le cancer, les déformations congénitales ou autres problèmes de la reproduction. Portez de l’équipement de protection.

Avertissement D’Air

Respirable

Ce compresseur/pompe n’est pas équipé pour et ne devrait pas être utilisé “comme soi” pour fournir de l’air respirable. En cas d’applications d’air pour la consommation humaine, le compresseur d’air/pompe doit être équipé avec de l’équipement de sécurité en canalisation et d’alarme. Cet équipement additionnel est nécessaire pour filtrer et purifier l’air afin d’atteindre les spécifications minimales pour la respiration Grade D décrites dans le Compressed Gas Association Commodity Specification G 7.1 - 1966, OSHA 29 CFR 1910. 134, et/ou Canadian Standards Associations (CSA).

DÉNÉGATION DES GARANTIES SI LE COMPRESSEUR EST UTILISÉ POUR LES APPLICATIONS D’AIR

RESPIRABLE ET L’ÉQUIPEMENT DE SÉCURITÉ EN CANALISATION ET D’ALARME N’EST PAS UTILISÉ SIMULTANÉMENT, LES GARANTIES EN EXISTANCE SERONT ANNULÉES, ET LE FABRICANT NIE TOUTE RESPONSABILITÉ POUR N’IMPORTE QUELLE PERTE, BLESSURE OU DOMMAGE.

Ce produit ou son

cordon contient du plomb, un produit chimique qui de l’avis de l’État de Californie peut causer le cancer et des anomalies congénitales ou d’autres problèmes

pour la reproduction. Se laver les mains après toute manipulation.

Généralités sur la Sécurité

SÉCURITÉ DE FONCTIONNEMENT

Puisque le compresseur d’air et les autres pièces détachées (pompe, pistolets, filtres, graisseurs, tuyaux, etc.) font partie d’un système de haute pression, il est nécessaire de suivre les précautions suivantes:

MÉMENTO : Gardez votre preuve datée d’achat à fin de la garantie !

Joignez-la à ce manuel ou classez-la dans un dossier pour plus de sécurité.

© 2009

7 Fr

IN626100AV 4/09

 

 

Oilless Compressors

Généralités sur la Sécurité (suite)

1. Lire attentivement tous

manuels compris avec ce produit. Se familiariser MANUAL avec ce produit, ses

commandes et son utilisation.

2.Suivre tous les codes de sécurité locaux ainsi que les National Electrical Codes (NEC) and Occupational Safety and Health Act (OSHA) des É.-U.

3.Seules les personnes bien familiarisées avec ces règles d’utilisation doivent être autorisées à se servir du compresseur.

4.Garder les visiteurs à l’écart de/et NE JAMAIS permettre les enfants dans l’endroit de travail.

5.Utiliser des lunettes de

sécurité et la protection auditive pendant l’utilisation du modèle.

6.Ne pas se tenir debout sur/ni utiliser le modèle comme une prise.

7.Inspecter le système d’air comprimé et pièces détachées électriques pour toute indication de dommage, détérioration, faiblesse ou fuites avant chaque utilisation. Réparer ou remplacer toutes pièces défectueuses avant l’utilisation.

8.Inspecter le degré de serrage de toutes attaches par intervalles régulières.

Ne jamais essayer

de réparer ou de modifier un réservoir! Le soudage, perçage ou autre modifications peuvent affaiblir le réservoir

et peuvent résulter en dommage de rupture ou d’explosion. Toujours remplacer un réservoir usé, fendu ou endommagé.

Les pièces du

compresseur peuvent être chaudes, même si le modèle est hors circuit.

9.Garder les doigts à l’écart du compresseur; les pièces mobiles et chaudes peuvent causer des blessures et/ou des brûlures.

10.Si l’équipement vibre anormalement, ARRÊTER le moteur et l’inspecter immédiatement. La vibration est généralement une indication d’un problème.

11.Pour réduire le risque d’incendie, garder l’extérieur du moteur libre d’huile, de solvant ou de graisse excessive.

Ne jamais enlever ou essayer

d’ajuster la soupape de sûreté. Tenir la soupape de sûreté libre de peinture et d’autres accumulations.

Ne jamais essayer de réparer ou de modifier un réservoir! Le soudage, perçage ou autre

modifications peuvent affaiblir le réservoir et peuvent résulter en dommage de rupture ou d’explosion. Toujours remplacer un réservoir usé, fendu ou endommagé.

Purger le réservoir quotidiennement.

12.L’accumulation d’humidité cause la rouille qui peut affaiblir le réservoir. Assurez vous de drainer le réservoir chaque jour et de contrôler périodiquement pour découvrir de conditions de danger comme la formation d’oxydation et la corrosion.

13.L’air mouvante peut agiter la poussière et le débris qui peut être dangereux. Lâcher l’air lentement en purgeant l’humidité ou pendant la dépressurisation du système du compresseur.

PRÉCAUTIONS DE PULVÉRISATION

Ne pas

pulvériser les matériaux inflammables dans un endroit de flamme ouverte ni près d’une source d’ignition y compris le compresseur.

14.Ne pas fumer pendant la pulvérisation de la peinture, d’insecticides ou autres matières inflammables.

15.Utiliser un masque / respirateur pendant la pulvérisation et pulvériser dans un endroit bien ventilé pour éviter le

risque de blessures et d’incendie.

16.Ne pas diriger la peinture ou autre matériel pulvérisé vers le compresseur. Situer le compresseur aussi loin que possible de l’endroit de pulvérisation pour réduire l’accumulation de surpulvérisation sur le compresseur.

17.Suivre les instructions du fabriquant pendant la pulvérisation ou le nettoyage avec des solvants ou produits chimiques toxiques.

Installation

ENDROIT

Le réservoir doit être nivelé ou incliné un peu vers le robinet de vidange afin de permettre le vidange correct.

Il est très important d’installer le compresseur dans un endroit propre et bien ventilé où la température n’excédera pas 40˚ C (104˚ F).

Laisser un espace libre de 10,16 cm (minimum) entre le compresseur et le mur car les objets peuvent obstruer la circulation d’air.

Ne pas situer la prise d’air du

compresseur près de la vapeur, un jet pulvérisé de peinture, endroits de décapage au sable ou autre sources de contamination. Le débris endommagera le moteur.

INSTALLATION ÉLECTRIQUE

Seul un électri-cien qualifié doit

effectuer l’installa-tion électrique et raccordements électriques. Respecter toutes les codes locals et nationales de l’électricité.

INSTRUCTIONS DE MISE À LA TERRE

1.Ce produit est conçu pour l’utilisation d’un circuit de 120 volts et a une fiche de mise à la terre comme celle indiquée sur la Figure 1. Assurer que le modèle est branché à une prise de courant qui a la même configuration que la fiche. Ce produit doit être mis à la terre. Dans l’évenement d’un court-circuit, la mise à la terre diminue le risque de secousse électrique en fournissant un fil d’échappement pour le courant électrique. Ce produit est équipé avec un cordon qui a un fil de terre avec une fiiche de terre. Le cordon doit être branché dans une prise de courant qui a été installée et mise à la terre correctement en respectant tous les codes et règlements locaux.

Grounded

Outlet

Grounded Pin

Figure 1

8 Fr

+ 16 hidden pages