Campbell Hausfeld IN615601AV User Manual

1.44 Mb
Loading...

Operating Instructions

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference.

Oil-Lubricated Compressors

D e s c r i p t i o n

This residential oil-lubricated compressor is designed for do-it-yourselfers with a variety of home and automotive jobs. These compressors power spray guns, impact wrenches and other tools. Compressed air from this unit will contain moisture. Install a water filter or air dryer if application requires dry air.

Safety Guidelines

This manual contains information that is very important to know and understand. This information is provided for SAFETY and to PREVENT EQUIPMENT PROBLEMS . To help recognize this information, observe the following symbols.

Danger indicates an imminently

hazardous situation which, if not avoided, WILL result in death or serious injury.

Warning indicates a potentially

hazardous situation which, if not avoided, COULD result in death or serious injury.

Caution indicates a p o t e n t i a l l y

hazardous situation which, if not avoided, MAY result in minor or moderate injury.

Notice indicates i m p o r t a n t

information, that if not followed, MAY cause damage to equipment.

U n p a c k i n g

After unpacking the unit, inspect carefully for any damage that may have occurred during transit. Make sure to tighten fittings, bolts, etc., before putting unit into service. In case of questions, damaged or missing parts, please call 1-800-543-6400 for customer assistance or call the nearest Campbell Hausfeld Authorized Service Center. Have the serial number, model number, and parts list (with missing parts circled) before calling.

DO NOT RETURN THE

PRODUCT TO THE

R E T A I L E R !

Record the Model No., Serial No. and date of purchase located on the base below the pump in the space below.

Model No. _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

Serial No. _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

Date of purchase _________________

Retain these numbers for future reference.

General Safety

I n f o rm a t i o n

CALIFORNIA PROPOSITION 65

You can create dust when you cut, sand,

drill or grind materials such as wood, paint, metal, concrete, cement, or other masonry. This dust often contains chemicals known to cause cancer, birth defects, or other reproductive harm. Wear protective gear.

This product or its power cord may

contain chemicals, including lead, known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.

GENERAL SAFETY INFORMATION

Do not operate unit if damaged

during shipping, handling or use. Damage may result in bursting and cause injury or property damage.

Do not run unattended. Leaving

compressor in AUTO position may allow it to turn on inadvertently. To prevent this and possible damage from power surge, turn to OFF position after each use.

Since the air compressor and other components (filters, lubricators, hoses, etc.) used, make up a high pressure pumping system, the following safety precautions must be observed at all times:

1 . Read all manuals included with this product carefully. Be thoroughly familiar with the controls and

the proper use of the equipment.

© 2008 Campbell Hausfeld/Scott Fetzer

For parts, product & service information

IN615601AV 12/08

visit www.chpower.com

Oil-Lubricated Compressors

General Safety I n f o rm a t i o n

( C o n t i n u e d )

2 . Follow all local electrical and safety codes as well as in the US, National Electrical Code (NEC) and Occupational Safety and Health Act ( O S H A ) .

3 . Only persons well acquainted with these rules of safe operation should be allowed to use the compressor.

4 . Keep visitors away and NEVER allow children in the work area.

5 . Wear safety glasses and use hearing protection when operating the pump or unit.

6 . Do not stand on or use the pump or unit as a handhold.

7 . Before each use, inspect compressed air system and electrical components for signs of damage, deterioration, weakness or leakage. Repair or replace defective items before using.

8.Check all fasteners at frequent intervals for proper tightness.

Motors, electrical equipment and controls can cause electrical arcs that will ignite a

flammable gas or vapor. Never operate or repair the unit near a flammable gas or vapor. Never store flammable liquids or gases in the vicinity of the

c o m p r e s s o r .

Compressor parts may be hot even if the unit is stopped.

9 . Keep fingers away from a running compressor; fast moving and hot parts will cause injury and/or burns.

1 0 . If the equipment should start to abnormally vibrate, STOP the engine/motor and check immediately for the cause. Vibration is generally a warning of trouble.

1 1 . To reduce fire hazard, keep engine/motor exterior free of oil, solvent, or grease.

Never remove or attempt to adjust

safety valve. Keep safety valve free from paint and other accumulations.

Never attempt to repair or modify a tank! Welding, drilling or any other modification will

weaken the tank resulting in damage from rupture or explosion. Always replace worn or damaged tanks.

Drain liquid from tank daily.

1 2 . Tanks rust from moisture build-up, which weakens the tank. Make sure to drain tank daily and inspect periodically for unsafe conditions such as rust formation and corrosion.

1 3 . Fast moving air will stir up dust and debris which may be harmful. Release air slowly when draining moisture or depressurizing the compressor system.

This product or its power cord

contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Wash hands after handling.

SPRAYING PRECAUTIONS

Do not spray f l a m m a b l e

materials in vicinity of open flame or near ignition sources including the compressor unit.

1 4 . Do not smoke when spraying paint, insecticides, or other flammable

s u b s t a n c e s .

1 5 . Use a face mask/ respirator when spraying and spray in a well ventilated area to prevent health and fire hazards.

1 6 . Do not direct paint or other sprayed material at the compressor. Locate compressor as far away from the spraying area as possible to minimize overspray accumulation on the compressor.

1 7 . When spraying or cleaning with solvents or toxic chemicals, follow the instructions provided by the chemical manufacturer.

Lock Nuts

W a s h e r s

S c r e w s

Figure 1 - Handle Assembly

A s s e m b l y

HANDLE ASSEMBLY (Figure 1)

1 . Place ends of handle around tank, behind the mounting plate. Align holes in handle to holes in mounting p l a t e .

2 . Assemble four (4) screws and washers (from parts package) through holes in mounting plate and handle. Secure with lock nuts.

Never use the handle to lift the

unit completely off the ground. Only use the handle to lift one end so the wheels may be used to move the unit.

WHEEL ASSEMBLY (Figure 2)

Wheel assembly kit includes:

-2 wheels*

-2 axle bolts*

-2 lock washers*

-2 nuts*

The items marked with an asterisk (*) were shipped loose with the unit.

1 . Wheel has an offset hub. With offset hub facing axle iron, assemble axle bolt through holes in wheel and axle i r o n .

N u t

Lock washer

W h e e l

Axle bolt

Figure 2 - Wheel Assembly

w w w . c h p o w e r . c o m

2

Assembly ( C o n t i n u e d )

2 . Place lock washer on axle bolt. Then tighten nut securely to threaded part of axle bolt.

3 . Repeat procedure with other side.

LUBRICATION

THIS UNIT IS SHIPPED WITHOUT

O I L ! Follow lubrication instructions before operating compressor.

Use oil shipped with the compressor.

Do not use regular automotive oil such as 10W-30. Additives in regular motor oil can cause valve deposits and reduce pump life. For maximum pump life, drain and replace oil after the first few hours of run time.

The compressor pump takes approximately 380 ml (13 ozs.) of oil. The sight glass, located on the crankcase portion of the pump, is marked with “max” and “min” levels. Avoid overfilling by adding oil gradually and checking the oil level with the sight glass several

M a x .

M i n.

Figure 3 - Proper oil level

Side view of unit

Intake filter

Oil fill / breather

Sight glass

Handle

Oil drain plug

Drain valve

Figure 6 - Unit Identification

Figure 4 - Intake filter installation

times. Add enough oil to reach the “max” level on the sight glass. Proper oil level is illustrated in Figure 3.

INTAKE FILTER

Thread the intake air filter into the threaded opening in the side of the compressor head as illustrated in Figure 4. Tighten gently with a wrench.

I n s t a l l a t i o n

L O C A T I O N

It is extremely important to install the compressor in a clean, well ventilated area where the surrounding air temperature will not be more than

1 0 0 ° F .

A minimum clearance of 18 inches between the compressor and a wall is required because objects could obstruct air flow.

 

 

 

Top view of unit

Exhaust

 

Pressure Switch

Tube

 

 

(Auto/Off)

 

 

 

 

 

Check

Safety Regulator

Valve

Valve

Grounding

Pin

Grounded Outlet

Figure 5 - Grounding Method

Do not locate the compressor air inlet

near steam, paint spray, sandblast areas or any other source of contamination. This debris will damage the motor.

ELECTRICAL INSTALLATION

All wiring and e l e c t r i c a l

connections should be performed by a qualified electrician. Installation must be in accordance with local codes and national electrical codes.

W I R I N G

1 . Local electrical wiring codes differ from area to area. Source wiring, plug and protector must be rated for at least the amperage and voltage indicated on motor nameplate, and meet all electrical codes for this minimum.

2 . Use a slow blow fuse or a circuit b r e a k e r .

3 . This product is for use on a nominal 120 volt circuit and has a grounding plug that looks like the plug illustrated in Figure 5. Make sure the product is connected to an outlet having the same configuration as the plug. This product must be grounded. In the event of an electrical short circuit, grounding reduces risk of electrical shock by providing an escape wire for electric current. This product is equipped with a cord having a grounding wire with an appropriate grounding plug. Plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Overheating, short circuiting and fire

damage will result from inadequate w i r i n g .

Extension cords for 120V/15 Amp Unit

Length of Cord (ft)

2 5

5 0

1 0 0

 

 

 

 

Gauge of Cord

1 4

1 2

1 0

 

 

 

 

w w w . c h p o w e r . c o m

3

Oil-Lubricated Compressors

Operation

• P r e ssure Switch - Auto/Off Switch (Figure7) - In the AUTO position, the compressor shuts off automatically when tank pressure reaches the maximum preset pressure. In the OFF position, the compressor will not operate. This switch should be in the OFF position when connecting or disconnecting the power cord from the electrical outlet or when changing air tools.

Figure 7 - Auto/Off switch

R e g u l a t o r - The regulator controls the amount of air pressure released at the hose outlet.

ASME Safety Valve - This valve automatically releases air if the tank pressure exceeds the preset maximum.

Exhaust Tube - This tube carries compressed air from the pump to the check valve. This tube becomes very hot during use. To avoid the risk of severe burns, never touch the exhaust tube.

Check Valve - A one-way valve that allows air to enter the tank, but prevents air in the tank from flowing back into the compressor pump.

Handle - Designed to move the c o m p r e s s o r .

Never use the handle on wheeled

units to lift the unit completely off the g r o u n d .

Drain Valve - This valve is located on the bottom of the tank. Use this valve to drain moisture from the tank daily to reduce the risk of corrosion.

Reduce tank pressure below 10 psi, then drain moisture from tank daily to avoid tank corrosion. Drain moisture from tank by opening the drain valve located underneath the tank.

BEFORE FIRST START-UP

BREAK-IN PROCEDURE

(Complete this procedure before using compressor for the first time. Once completed, it is not necessary to repeat.)

1 . Turn regulator knob fully clockwise (to the right) to open air flow.

2 . Turn on/off switch to OFF position.

3 . Plug in power cord.

4 . Turn on/off switch to AUTO position and run compressor for 30 minutes.

5 . Turn on/off switch to OFF position.

6 . Unplug power cord.

The compressor is now ready for use.

BEFORE EACH START-UP

OPERATING PROCEDURE

1 . Turn regulator knob fully counter clockwise (to the left) to close air flow.

2.Connect air hose to outlet of r e g u l a t o r .

3 . Turn on/off switch to OFF position.

4 . Plug in power cord.

5 . Turn on/off switch to AUTO position and let compressor run until it reaches automatic shutoff pressure.

6 . Attach tire chuck or tool to end of h o s e .

7 . Turn regulator knob clockwise (to the right) to desired pressure of tool being used.

On/Off cycling of compressor

In the AUTO position, the compressor pumps air into the tank. When a shutoff (preset “cut-out”) pressure is reached, the compressor automatically shuts off.

If the compressor is left in the AUTO position and air is depleted from the tank by use of a tire chuck, tool, etc., the compressor will restart automatically at its preset “cut-in” pressure. When a tool is being used continuously, the compressor will cycle on and off automatically.

In the OFF position, the pressure switch cannot function and the compressor will not operate. Make sure switch is in OFF position when connecting or disconnecting power cord from electrical outlet.

ASME SAFETY VALVE

Do not remove or attempt to adjust

the safety valve!

Check the safety valve by performing the following steps:

1 . Plug the compressor in and run until shut off pressure is reached (see Operating Procedure).

2 . Wearing safety glasses, pull the ring on the safety valve (see Figures 6 and 8) to release pressure from compressor tank. Use your other hand to deflect fast-moving air from being directed toward your face.

Figure 8

w w w . c h p o w e r . c o m

4

Operation ( C o n t i n u e d )

3 . The safety valve should automatically close at approximately 40-50 PSI. If the safety valve does not allow air to be released when you pull on the ring, or if it does not close automatically, it MUST be replaced.

Safety valve must be replaced if it

cannot be actuated or it leaks air after ring is released.

PRESSURE GAUGES

Gauge attached to regulator indicates air pressure going to hose (and any tool attached to end of hose).

Gauge attached to pressure switch indicates air pressure in tank.

M a i n t e n a n c e

Disconnect power source and then release all pressure from the system before attempting to install, service, relocate or perform any

m a i n t e n a n c e .

Check compressor often for any visible problems and follow maintenance

procedures each time compressor is u s e d .

1 . Turn compressor off and release pressure from system. To release pressure from system, pull ring on ASME safety valve (see Figures 6 and 8 ). Deflect escaping air by shielding valve with one hand as you pull ring with other hand. Pull ring until tank is empty.

A large amount of fast moving air will

be released when the safety valve is opened with pressure in the tank. Wear ANSI approved Z87.1 safety glasses.

2 . Drain moisture from tank by opening drain valve (see Figure 6) underneath tank. Tilt tank to remove all

m o i s t u r e .

3 . Clean dust and dirt from tank, air lines and pump cover while compressor is still OFF.

OIL CHANGE

1 . Allow compressor to run and warm up oil. Unplug unit.

2 . Position a pan under pump end of u n i t .

3 . Remove oil drain plug (see Figure 6). Allow oil to collect in pan. Tilt unit to completely drain.

4 . Replace drain plug, fill pump to full line on sight glass. Use Chevron synthetic 5W-30, Mobil 1 5W-30 or 10W-30 synthetic motor oil. Using other types of oil will cause starting p r o b l e m s .

5 . Change oil after every 50 hours of u s e .

I N T A K E AIR FILTER MAINTENANCE

Removal, Inspection and Replacement (Figure 9)

Filter element

F i l t e r c o v e r

Figure 9 - Intake filter maintenance

The intake filter element should be removed and checked periodically. A clogged intake filter can decrease compressor performance and cause the compressor to overheat.

1.Rotate the filter cover counter clockwise and remove .

2 . Remove the filter element and i n s p e c t .

3 . If the filter element is dirty or clogged, replace it.

4 . Reinstall filter and cover.

IMPORTANT: Locate unit as far from spraying area as hose will allow to prevent overspray from clogging filter.

OVERLOAD PROTECTOR SECTION

This compressor is equipped with a

thermal overload protector which will shut off motor if it becomes overloaded.

If overload protector shuts motor OFF frequently, look for the following

c a u s e s .

1 . Low voltage.

2 . Clogged air filter.

3 . Lack of proper ventilation.

If the overload protector is

actuated, the motor must be allowed to cool down for 30 minutes. To reset once the motor has cooled down, turn pressure switch to the OFF position then to the AUTO position.

S T O R A G E

1 . Drain tank of moisture.

2 . When not in use, store compressor in a cool, dry place.

3 . Disconnect hose and hang open ends down to allow any moisture to drain.

w w w . c h p o w e r . c o m

5

Oil-Lubricated Compressors

Troubleshooting Chart

 

Symptom

Possible Cause(s)

Corrective Action

 

 

 

 

 

 

Compressor will not run

1 . Switch in OFF position

1

. Make sure compressor is plugged in and switch is ON.

 

 

2

. No electrical power at wall outlet

2

. Check circuit breaker or fuse at electrical panel.

 

 

3

. Compressor has reached automatic

3

. Release air from tank until compressor restarts

 

 

 

shutoff pressure

 

a u t o m a t i c a l l y .

 

 

4

. Motor overloaded

4

. Allow compressor to cool for approximately 30

 

 

 

 

 

minutes. To reset, turn pressure switch to OFF, then

 

 

 

 

 

AUTO. Make sure compressor is run in a clean, well-

 

 

 

 

 

ventilated area.

 

 

5

. Pressure switch bad

5

. Replace pressure switch.

 

 

 

 

 

 

Motor hums but cannot

1 . Defective check valve

1

. Repair or replace.

 

run or runs slowly

2 . Defective unloader valve (on pressure

2

. Repair or replace.

 

 

 

s w i t c h )

3

. Check voltage at wall outlet with voltmeter.

 

 

3

. Low voltage

 

 

4

. Loose electrical connections

4

. Check all electrical connections.

 

 

5

. Wrong gauge wire or length of

5

. Check extension cord chart for proper extension cord

 

 

 

extension cord

 

u s a g e .

 

 

6

. Defective motor capacitor

6

. Replace capacitor.

 

 

7

. Shorted or open motor winding

7

. Replace motor assembly.

 

 

 

 

 

Do not disassemble check valve

 

 

 

 

 

with air in tank; bleed tank

 

 

 

 

 

 

Flow blows/circuit

1 . Incorrect fuse size, circuit overloaded

1

. Check for proper fuse. Use time delay fuse.

 

breaker trips repeatedly

 

 

 

Disconnect other electrical appliances from circuit or

 

 

 

 

 

operate compressor on its own branch circuit.

 

 

2

. Wrong gauge wire or length of

2

. Check extension cord chart for proper extension cord

 

 

 

extension cord

 

u s a g e .

 

 

3

. Defective check valve

3

. Repair or replace.

 

 

4

. Defective unloader valve (on pressure

4

. Repair or replace.

 

 

 

s w i t c h )

5

. Replace capacitor.

 

 

5

. Defective motor capacitor

 

 

6

. Motor shorted or seized

6

. Replace motor assembly.

 

 

 

 

 

Do not disassemble check valve

 

 

 

 

 

with air in tank; bleed tank

 

 

 

 

 

 

Thermal overload

1 . Low voltage

1

. Check voltage at wall outlet with voltmeter.

 

protector cuts out

2 . Wrong gauge wire or length of

2

. Check extension cord chart for proper extension cord

 

r e p e a t e d l y

 

extension cord

 

u s a g e .

 

 

3

. Clogged intake filter

3

. Clean or replace filter.

 

 

4

. Lack of proper ventilation/room

4

. Move compressor to well-ventilated area.

 

 

 

temperature too high

5

. Repair or replace.

 

 

5

. Defective check valve

 

 

6

. Defective unloader valve (on pressure

6

. Repair or replace.

 

 

 

s w i t c h )

7

. Replace valve assembly.

 

 

7

. Compressor valves failed

 

 

 

 

 

Do not disassemble check valve

 

 

 

 

 

with air in tank; bleed tank

 

 

 

 

 

 

Knocks, rattles, and/or

1 . Loose mounting bolts

1

. Tighten bolts.

 

excessive vibration

2 . Tank not level

2. Use sturdy wedge/object to bring tank to level position.

 

 

3

. Cylinder or piston is worn/scored

3

. Replace or repair as necessary.

 

 

 

 

 

 

Tank pressure drops

1 . Loose drain valve

1

. T i g h t e n .

 

when compressor shuts

2 . Check valve leaking

2

. Remove check valve. Clean or replace.

 

o f f

3 . Loose connections at fittings, tubing,

3

. Check all connections with soap and water solution.

 

 

 

e t c .

 

If a leak is detected, (1) tighten or (2) remove fitting

 

 

 

 

 

and apply pipe tape to threads and reassemble.

 

 

4

. Tank leaks

4

. Check tank for leaks with soap and water solution. If

 

 

 

 

 

leak is detected, tank must be replaced with genuine

 

 

 

 

 

replacement part.

Do not disassemble check valve with air in tank; bleed tank

Compressor runs continuously and air output is lower than normal/low discharge p r e s s u r e

1

. Excessive air usage, compressor too

1

. Decrease usage or purchase unit with higher air

 

 

s m a l l

 

delivery (SCFM).

2.

Clogged intake filter

2

. Clean or replace.

3

. Loose connections at fittings, tubing,

3

. Check all connections with soap and water solution.

 

 

e t c .

 

If a leak is detected, (1) tighten or (2) remove fitting

 

 

 

 

and apply pipe tape to threads and reassemble.

w w w . c h p o w e r . c o m

6

Troubleshooting Chart (Continued)

 

Symptom

Possible Cause(s)

Corrective Action

 

 

 

 

 

 

 

 

 

4 . Tank leaks

4

. Check tank for leaks with soap and water solution. If

 

 

 

 

 

 

leak is detected, tank must be replaced with genuine

 

 

 

 

 

 

replacement part.

 

 

 

5.

Broken valves

5

. Replace compressor valves as necessary.

 

 

 

6.

Piston ring worn

6

. Replace piston and cylinder.

 

 

 

 

 

 

 

 

Excessive moisture in

1 . Excessive water in tank

1

. Drain tank.

 

 

discharge air

2 . High humidity

2

. Move to area of less humidity; use air line filter.

 

 

 

 

 

 

NOTE: Water condensation is not caused by

 

 

 

 

 

 

compressor malfunction.

 

 

 

 

 

 

 

 

Compressor runs

1 . Defective pressure switch

1

. Replace switch.

 

 

continuously and safety

2 . Defective safety valve

2

. Replace safety valve with genuine replacement part.

 

 

valve opens as pressure

 

 

 

 

 

 

r i s e s

 

 

 

 

 

 

 

 

 

 

 

 

Excessive starting and

1. Excessive condensation in tank

1

. Drain more often.

 

 

stopping (auto start)

2 . Loose connections at fittings, tubing,

2

. Check all connections with soap and water solution.

 

 

 

 

e t c .

 

If a leak is detected, (1) tighten or (2) remove fitting

 

 

 

 

 

 

and apply pipe tape to threads and reassemble.

 

 

 

3 . Tank leaks

3

. Check tank for leaks with soap and water solution. If

 

 

 

 

 

 

leak is detected, tank must be replaced with genuine

 

 

 

 

 

 

replacement part.

 

 

 

 

 

 

Do not disassemble check valve

 

 

 

 

 

 

with air in tank; bleed tank

 

 

 

 

 

 

 

 

Air leaking from

1 . Check valve stuck in an open position

1

. Repair or replace check valve.

 

 

unloader valve on

2 . Unloader valve stuck in open position

2

. Repair or replace unloader valve.

 

 

pressure switch

 

 

 

Do not disassemble check valve

 

 

 

 

 

 

with air in tank; bleed tank

 

 

 

 

 

 

 

 

w w w . c h p o w e r . c o m

7

Oil-Lubricated Compressors

Limited Wa rr a n t y

1 . DURATION: From the date of purchase by the original purchaser as follows: Standard Duty - One Year; Serious Duty - Two Years; Extreme Duty - Three Years. Maxus branded compressors carry a five (5) year warranty.

2 . WHO GIVES THIS WARRANTY (WARRANTOR):

Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive, Harrison, Ohio, 45030, Telephone: (800) 543-6400

3 . WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the Campbell Hausfeld compressor.

4 . WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: Any Campbell Hausfeld air compressor.

5 . WHAT IS COVERED UNDER THIS WARRANTY: Substantial defects due to material and workmanship with the exceptions noted below.

6.WHAT IS NOT COVERED UNDER THIS WARRANTY:

A . Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED FROM THE DATE OF ORIGINAL PURCHASE AS STATED IN THE DURATION. If the compressor is used for commercial (everyday use in a business operation), industrial (daily plant operation), or rental purposes, the warranty will apply for ninety

(90)days from the date of purchase. Extreme Duty Compressors are not limited to a ninety (90) day warranty when used in contractor applications. Maxus brand compressors are not limited to a ninety (90) day warranty when used in commercial and contractor applications. Four cylinder single-stage and two-stage compressors are not limited to a ninety (90) day warranty when used in commercial or industrial applications. Some states do not allow limitations on

how long an implied warranty lasts, so the above limitations may not apply to you.

B . ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY DEFECT, FAILURE, OR MALFUNCTION OF THE CAMPBELL HAUSFELD PRODUCT. Some States do not allow the exclusion or limitations of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

C . Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate products in accordance with instructions provided in the owner’s manual(s) supplied with compressor.

D . Pre-delivery service, i.e. assembly, oil or lubricants, and adjustment.

E . Items or service that are normally required to maintain the product, i.e. lubricants, filters and gaskets, etc.

F . Gasoline engines and components are expressly excluded from coverage under this limited warranty. The Purchaser must comply with the warranty given by the engine manufacturer which is supplied with the product.

G . Additional items not covered under this warranty: 1 . All Compressors

a . Any component damaged in shipment or any failure caused by installing or operating unit under conditions not in accordance with installation and operation guidelines or damaged by contact with tools or surroundings.

b . Pump or valve failure caused by rain, excessive humidity, corrosive environments or other contaminants. c . Cosmetic defects that do not interfere with compressor functionality.

d . Rusted tanks, including but not limited to rust due to improper drainage or corrosive environments. e . Electric motors, check valves and pressure switches after the first year of ownership.

f . Drain cocks.

g . Damage due to incorrect voltage or improper wiring.

h . Other items not listed but considered general wear parts.

i . Pressure switches, air governors and safety valves modified from factory settings. 2 . Lubricated Compressors

a . Pump wear or valve damage caused by using oil not specified.

b . Pump wear or valve damage caused by any oil contamination or by failure to follow proper oil maintenance g u i d e l i n e s .

3 . Belt Drive / Direct Drive / Gas Driven Compressors a . B e l t s .

b . Ring wear or valve damage from inadequate filter maintenance. c . Manually adjusted load/unload and throttle control devices.

7 . RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s option, compressor or component which is defective, has malfunctioned and/or failed to conform within duration of the warranty period.

8 . RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:

A . Provide dated proof of purchase and maintenance records.

B . Portable compressors or components must be delivered or shipped to the nearest Campbell Hausfeld Authorized Service Center. Freight costs, if any, must be borne by the purchaser.

C . Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).

9 . WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY: Repair or replacement will be scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of replacement parts.

This Limited Warranty applies in the U.S., Canada and Mexico only and gives you specific legal rights. You may also have other rights which vary from State to State or country to country.

w w w . c h p o w e r . c o m

8

+ 16 hidden pages