Size:
1.44 Mb
Download

Assembly Instructions and Parts List

PW1686

 

 

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference.

Electric Pressure

Washer

NOTE: REFER TO PRODUCT MANUAL

FOR ALL SAFETY INSTRUCTIONS

Specifications

 

 

Max Pressure

 

Motor

 

Maximum

 

 

 

with

 

Power

 

Inlet

 

 

Cleaning

Standard

Maximum

(Single

 

Water

Unit

Model

Power

Lance

Capacity

Phase)

Voltage

Temp.

Weight

 

 

 

 

 

 

 

PW1686

2640

1650 psi

1.6 GPM 14 Amps

120V

100˚F

38 lbs.

Assembly Instructions

1.Attach detergent suction tube to hose barb on detergent tank and put cap on detergent tank (Figure 1).

2.Slide accessory storage bracket onto back of pressure washer (Figure 1).

3.Slide cord holder and lance storage collar onto side of pressure washer (Figure 1).

4.Align handle on back of pressure washer and attach using screws provided (Figure 1).

5.Assemble one wheel to axle and slide through back of pressure washer and detergent tank (Figure 2).

3

3

 

4

 

1

 

2

Figure 1

Figure 2

© 2003 Campbell Hausfeld

For parts, product & service information

IN463600AV 12/03

visit www.chpower.com

 

Assembly Instructions and Parts List

PW1686

Assembly Instructions (Continued)

6. Assemble second wheel to axle (Figure 3).

7. Attach hose holder with screws provided (Figure 4).

8. Attach lance storage holder with screw provided (FIgure 5).

9. Align hub cap locking tabs with wheels and press into place (Figure 5).

Figure 3

Figure 5

Figure 4

www.chpower.com

2

! WARNING
! CAUTION
! CAUTION

Assembly Instructions and Parts List

PW1686

Garden Hose Connection

GARDEN HOSE CONNECTION INSTRUCTIONS

1.Attach nipple adapter to inlet fitting on the unit (this may already be attached to the pump).

2. Attach quick connect fitting to garden hose.

3.Pull side “A” of quick connect fitting toward garden hose and push onto nipple adapter.

4.Push side “A” of quick connect fitting towards nipple adapter and release.

"A"

Quick Connect Fitting

Garden Hose

Nipple

Adapter

Figure 6 - Garden Hose Connection

Power Cord

1.Plug the power cord into a grounded 120V outlet and press the reset button as shown in Figure 7.

2.THIS MUST BE DONE EACH TIME THE UNIT IS PLUGGED IN AN OUTLET.

Reset

Figure 7 - Grounded plug/reset button

! IMPORTANT !

This pressure washer is equipped with a microswitch sensitive to water flow. This Instant Start/Stop switch (ISS) senses water flow in the pump. When the trigger is released, water stops flowing through the pump. The ISS then automatically turns the motor off to protect pump from overheating.

OPERATION

1.Pull trigger on gun.

2.Turn the “ON/OFF” switch to “ON”.

3.Release trigger. The pressure washer motor will stop running.

4.To spray again, pull trigger and motor and pump will restart.

Note: Occasionally the motor may run for a short time to bring fresh, cool water into the pump even if trigger is released. This is part of normal operation and will not damage the unit.

Always turn the

“ON/OFF” switch to “OFF” then trigger gun to release hose pressure before unplugging power cord.

Risk of equipment dam- age. Always make sure the “ON/OFF” switch on the unit is “OFF” and unit is unplugged prior to storage.

Risk of Injection.

Unit will start spraying when trigger is squeezed if on/off switch is in “ON” position. Always point gun in safe direction.

Call 1-800-330-0712 for Technical Service

www.chpower.com

3

Assembly Instructions and Parts List

PW1686

System Connection

1.Insert lance into the gun and turn clockwise to positive stop as shown in Figure 8.

Figure 8 - Gun/Lance Connection

2.Ensure that the power switch is in the “OFF” position.

3.Attach the high pressure hose and gun assembly to the unit.

4.Connect garden hose as explained under Garden Hose Connection Instructions.

5.Plug the power cord into a grounded 120V outlet, that is on a dedicated circuit.

6.Turn water on.

7.Depress and hold the trigger on the gun for one minute to release pressure and remove any air trapped in the system.

8.Turn the “ON/OFF” switch to the “ON” position.

NOTE: REFER TO PRODUCT MANUAL FOR OPERATING INSTRUCTIONS

High

Pressure

Hose

Gun

On/Off

Switch

13 mm

INLET

Garden

Hose

Figure 9

www.chpower.com

4

Assembly Instructions and Parts List

PW1686

 

 

Replacement Parts List

For Replacement Parts,

Call 1-800-330-0712

Please provide following information:

-Model number -Serial number (if any)

-Part description and number as shown in parts list

 

Address parts correspondence to:

 

The Campbell Group / Parts Dept.

8

100 Production Drive

 

 

Harrison, OH

45030 U.S.A.

 

9

 

4

20

10

 

 

1

 

 

 

 

11

 

 

9

 

 

 

19

9

5

 

3

2

12

 

 

 

 

 

13

6

 

18 14

16

17

15

7

Ref.

 

Part

 

 

No.

Description

Number

Qty.

 

 

 

 

 

 

1

Adjustable pressure lance

PM271080SV

1

 

2

Turbo lance

PM022621AV

1

 

3

Hose

PM243600AV

1

 

4

Gun

PM037201SJ

1

 

5

Nipple adapter

PM022100AV

1

 

6

Quick connect fitting

PM020600SV

1

 

7

Tip cleaner

PM008500AV

1

 

8

Handle

PM271000SV

1

 

9

Hardware pack

PM271010SV

1

 

10

Lance storage collar

PM271020SV

1

 

11

Accessories storage bracket

PM271030SV

1

 

12

Lance storage holder

PM271040SV

1

 

13

Hose holder

PM270050SV

1

 

14

Detergent tank cap

PM060000SV

1

 

15

Detergent tank

PM271050SV

1

 

16

Wheel cover

PM066300SV

2

 

17

Wheel

PM066301SV

2

 

18

Axle

PM271060SV

1

 

19

Cord holder

PM271070SV

1

 

20

O-ring

PM232200SV

1

 

 

 

 

 

 

www.chpower.com

5