Camden Door Controls CM-333-40, CM-333-41, CM-333-42, CM-333-43, CM-333-44 User Manual

...
0 (0)

D o o r A c t i v a t i o n D e v i c e s

CM-333 Series

Battery Operated with Relay Output Active Infra-red “Hands-Free” Switches

INSTALLATION INSTRUCTIONS

1. GENERAL DESCRIPTION

Sure-Wave™ Hands-Free Switch are active infra-red devices utilizing micro burst sensor technology, designed for use in ADA compliant automatic door control applications. The switches eliminate the spread of germs by avoiding physical contact and offer building occupants greater convenience when moving through the premises. Sure-Wave™ switches are available with either stainless steel or impact resistant polycarbonate faceplates, in narrow (jamb), single gang or double gang configurations. All models are ROHS compliant with

lead-free construction.

2. SPECIFICATIONS

Descriptions

CM-333

 

 

No. of IR Sensors

1

 

 

Batteries (Supplied)

'AA' Alkaline Batteries

(Supplied)

 

 

 

Estimated Battery Life

2 Years

(Based on 100

 

Operations/Day)

 

 

Standard Operating

1”- 12” (25.4mm - 304mm)

Range

Factory Set to 6” (152 mm)

 

 

Operating Mode

Momentary

Momentary with Alarm

 

Inputs

Request to Exit’ External

(Door Contact) Input

 

Wireless Output

TX-99 Plug-in 915Mhz. Spread

Spectrum Wireless

 

Transmitter

Relay Output

(1) Form ‘C‘ (SPDT)

 

 

Relay Contact Rating

2 Amps @ 30 VDC

 

 

Output Type

Fail-secure

 

 

3. APPLICATION

Sure-Wave™ battery powered hands-free switches are American Disability Act (ADA) compliant, and provide barrier free access and egress to buildings and washroom facilities. The rugged construction makes them ideal for use on low-energy automatic doors, drive-up windows, and interior and exterior doors in virtually any commercial (office, retail), institutional (school, hospital or clinic), or industrial (manufacturing) facility.

Three standard face plate widths are available:

CM-333: 2 ¾” x 4 ½” polycarbonate or stainless steel, fits on single gang electrical boxes.

CM-333/N: 1 ¾” x 4 ½” polycarbonate or stainless steel, fits 1 ¾” door frames or our CM-23D Jamb box.

CM-333/W: 4 ½” x 4 ½” polycarbonate or stainless steel, fits on single gang, double gang or 4 x 4 electrical boxes. All

faceplates may be ordered up with a plain face, with the waving hand symbol (/40), with the waving hand symbol and words: WAVE TO OPEN (/41) or with the waving hand icon, wheelchair and words: WAVE TO OPEN (/42).

4. INSTALLATION

Mounting

Sure-Wave™ may be mounted in door jambs, single or double gang electrical boxes, and 4 x 4 boxes.

NOTE: The sealing gasket (included) is recommended for outdoor or wet locations. If using with Automatic doors install in accordance with ANSI A156.10 / A156.19. Select from one of the following three mounting subsections:

SINGLE GANG ELECTRICAL BOX: CM-333

1.a) If using an in-wall box ensure the box is plumb and square, and flush with the wall surface. (See Diagram 1)

b)If using a surface box, ensure it is secure & plumb.

2.Bring your 2-conductor wire through the back or side of the enclosure and leave approximately 6” tail for wiring connection.

3.Make the electrical connections to the device according to the wiring section (following).

4.Using the dip switch located on the end of the unit, set the operating mode. (See Section 6)

Page 1 of 4

Camden Door Controls CM-333-40, CM-333-41, CM-333-42, CM-333-43, CM-333-44 User Manual

CM-333 BATTERY OPERATED

WITH RELAY OUTPUT ACTIVE INFRA-RED “HANDS-FREE” SWITCHES

INSTALLATION INSTRUCTIONS

5.Attach the unit to the enclosure using the two #6-32 screws provided.

6.Attach the unit to the enclosure using the two #6-32 screws provided. #6-32 x 3/8 machine screws or tamperproof screws.

Do not overtighten!!

DIAGRAM 1

PROPER BOX

INSTALLATION

Smooth

Wall Finish

Wall

Flush

Wall Box

Rough Wall

Finish

Recessed

Unaligned

Box

Box

2 GANG (or 4x4) ELECTRICAL BOX: CM-333W

1. a) If using an in-wall box ensure the box is plumb and square, and flush with the wall surface. (See Diagram 1)

1. b) If using a surface box, ensure it is secure & plumb.

1.c) If using a 4 x 4 box, ensure the box is plumb and square, and flush with the wall surface, then attach the metal adaptor plate (included in the CM-333W package) to the box using appropriate fasteners.

2.Bring your 2-conductor wire through the back or side of the enclosure and leave approximately 6” tail for wiring connection.

3. Make the electrical connections to the device according to the wiring section (following).

4.Using the dip switch located on the end of the unit, set the operating mode. (See Section 6)

5.Attach the unit to the enclosure using the two #6-32 screws provided.

6.Attach the faceplate to the unit using the two black #6-32 x 3/8 machine screws or tamperproof screws.

Do not overtighten!!

DOOR FRAME: CM-324N

1. a) If mounting directly in a 1¾” wide aluminum jamb, make a cutout in the door frame at the intended location as per Diagram 3. (See Diagram). Drill and tap two mounting holes as shown.

1.b) If mounting the unit in our CM-23D deep jamb box, first mount the jamb box according to the instructions packaged with the enclosure. Using the CM-23D as a guide, drill a wire access hole through the jamb to fish the wiring through.

2.Bring your 2-conductor wire through the back or side of the enclosure and leave approximately 6” tail for wiring connection.

3.Make the electrical connections to the device according to the wiring section (following).

4.Using the dip switch located on the end of the unit, set the operating mode. (See Section 6)

5.Attach the unit to the enclosure or jamb using the two #6-32 screws provided.

6.Attach the faceplate to the unit using the two black #6-32 x 3/8 machine screws or tamperproof screws.

Do not overtighten!!

Wiring

CAUTION: Do not apply power to the unit until all secondary wiring is complete, and dip-switches have been set.

The CM-333 is powered from 2 AA batteries (supplied). The battery holder has been pre-installed. Insert the batteries into the battery holder. Please be careful that the polarity of the batteries is correct.

The CM-333 output is a form ‘C’ relay. Selecting the correct output is also dependent on the operating mode chosen. Most applications will utilize the N.O. and Common terminals.

DIAGRAM 2

Power In -

Power In +

Request To

Exit Input

 

 

 

 

 

 

 

N

C

N

 

 

 

C

O

O

 

 

 

 

M

 

 

 

 

 

 

 

 

 

 

N

 

C

 

N

 

 

C

 

O

 

O

 

 

 

 

M

 

 

 

Page 2 of 4

Loading...
+ 2 hidden pages