Digital
ThermoFresh®
1.0 & 1.5 Gallon Server
with Countup Timer
USE & CARE INFORMATION
CAUTION: CLEAN AND SANITIZE YOUR SERVER BEFORE USING. SEE NOTE #1 of DAILY CLEANING.
BUNN-O-MATIC CORPORATION OF CANADA
280 INDUSTRIAL PARKWAY SOUTH,
AURORA, ONTARIO, L4G 3T9
PHONE: (905) 841-2866 FAX: (905) 841-2775
43240.7009B 11/12 ©2012 Bunn-O-Matic Corporation
INTRODUCTION
This server is intended for use with a BUNN® DUAL® TF DBC®, SINGLE® TF DBC® or ICB family brewers. When proper precautions are followed, 1.0 up to 1.5 gallons of coffee may be brewed directly into the server and then transported to a remote serving location. The server must be placed on a sturdy counter or shelf.
NOTE: Calibration of the brewer is required prior to the use of the Digital TF Server.
USER NOTICES
The notices on this server should be kept in good condition. Replace unreadable or damaged labels.
WARNING |
|
|
AVERTISSEMENT |
|
|
|
|
HOT LIQUID |
|
|
LIQUIDE CHAUD |
|
|
|
|
|
|
|
|
35710.7000
DO
NE
|
|
|
|
|
|
|
E |
|
|
|
N |
|
|
|
|
G |
|
|
|
||
|
|
|
E |
|
|
|
|
|
||
|
O |
M |
R |
|
|
|
|
|||
|
|
T SUB |
|
|
|
R |
|
|
|
|
P |
|
|
|
E |
|
|
|
|||
|
|
G |
|
|
|
|
|
|||
|
A |
|
R |
|
|
|
|
|
|
|
|
|
S IMME |
|
|
|
|
|
|
|
|
45457.7000 |
|
39043.0000 |
39043.0001 |
39043.0002 |
||||||
DAILY CLEANING
CAUTION: CLEAN AND SANITIZE YOUR SERVER DAILY
NOTE: Bunn-O-Matic recommends the 3 step method for cleaning and sanitizing the server. The 3 step method consists of hot soapy water using an approved detergent, a fresh water rinse, and an aqueous sanitizing solution using an approved non-chlorine sanitizer. Do not submerge server.
1.Run a complete brew cycle of just hot water into the server and let it set for a minute. Empty the server completely by opening the faucet.
2.Remove the sensor assembly, fill server with cleaning solution and thoroughly clean the inside of server.
3.Rinse server thoroughly using fresh water rinse.
4.Fill server with sanitizing solution and let the server set for 5 minutes, then drain through fully open faucet. Thoroughly rinse server after sanitizing.
5.Remove the faucet handle/stem assembly by unscrewing the faucet nut just beneath the faucet handle.
6.Use enclosed cleaning brush to thoroughly clean the faucet body and tube.
7.Disassemble the faucet/stem assembly. Thoroughly wash all faucet parts in a mild detergent and water solution. Rinse the parts in hot water. Sanitize the parts for five minutes, thoroughly rinse, then air dry completely.
8.Use enclosed cleaning brush to thoroughly clean the fill tube of the sensor assembly.
NOTE: Never submerge the Digital ThermoFresh® Server Display or sensor assembly in water.
9.Wipe sensor assembly with a clean, damp cloth.
10.Reassemble the faucet and attach it to the dispenser.
11.Wash the entire outside surface of the server and display with a clean damp cloth.
PERIODIC CLEANING
1.Remove the sensor assembly from the server.
2.Remove the two thumb screws and slide display assembly from the server.
3.Wipe the surface of the display unit, area under the display unit, and sensor assembly with a clean damp cloth.
4.Wash the entire outside surface of the sensor assembly with a mild detergent and water solution and rinse with hot water. Do not submerse. NOTE: Thoroughly cleaning the sensor assembly fins will prevent inaccurate level readings.
5.Replace the display unit and sensor assembly.
2 |
43240.9 030912 |
|
SERVER WITH STAND
REPLACEMENT PARTS |
17 |
16 15 14 13 |
||
1. |
42554.1001 |
Display Kit, Countup (Includes items 2 - 4) |
|
|
|
42826.1000 |
Screw, Thumb #6-32 x .25" |
|
12 34 |
2. |
46247.1000 |
Batteries, 4 Pack AAA |
|
1 |
3. |
42546.0001 |
Gasket, Battery Cover |
|
|
4. |
42547.0001 |
Cover, Battery |
|
2 |
|
02361.0000 |
Screw, Pan Head #4-40 x .25" |
|
|
5. |
43135.0000 |
Handle, Faucet |
18 |
3 |
6. |
29165.1002 |
Faucet Bonnet |
|
|
7. |
00601.1000 |
Faucet Spring (Package of 6) |
32 |
4 |
8. |
29164.1000 |
Faucet Stem (Package of 6) |
|
|
9. |
00600.1000 |
Faucet Seat Cup (Package of 6) |
19 |
5 |
10. |
42567.0000 |
Faucet Body |
|
|
11. |
42543.0000 |
Guard, Faucet |
33 |
6 |
|
35074.1000 |
Screw, Pan Head M4 x .7 x .25 |
|
|
12. |
43231.0000 |
Washer, M4 x 9MM |
35 |
7 |
42584.1000 |
Plug, Front (Package of 10) |
|
|
|
13. |
42818.1001 |
Sensor Assy, 1.0 Gal (Includes items 14 &15) |
20 |
8 |
|
42565.1000 |
Sensor Assy, 1.5 Gal (Includes items 14 &15) |
|
|
14. |
42563.1002 |
Cap, Sensor Assy (Package of 5) |
21 |
9 |
15. |
39043.0000 |
Decal, Do Not Submerge |
|
|
16. |
42562.0000* |
Handle, Server |
22 |
10 |
17. |
42758.0000* |
Shoulder Screw |
|
|
18. |
42585.1000 |
Plug, Rear (Package of 10) |
23 |
11 |
19. |
43246.1000 |
Cover Assy, Top |
|
|
|
42761.0000* |
Screw, Pan Head M4 x 9 |
24 |
|
20. |
35710.0000 |
Decal, Warning Hot Liquid |
|
|
21. |
32591.1000 |
Tube, Silicone .50" ID x 12.0" LG (cut to length) |
25 |
|
22. |
28526.1000 |
Tube, Silicone .31" ID x 12.0" LG (cut to length) |
|
31 |
23. |
42912.0000 |
Foot, Rubber |
26 |
|
|
43163.0000 |
Screw, Pan Head #8 x .75" |
|
|
24. |
42295.0001 |
Elbow, 90° |
27 |
|
25. |
42890.1000 |
Base Cover |
|
|
26. |
35016.0001 |
Insert, Stand |
|
|
27. |
38929.0002 |
Stand, Server |
|
|
|
39617.0000 |
Screw, Pan Hd Plastite #6 x .75" |
28 |
|
28. |
38930.0002 |
Base Plate, Stand |
|
|
|
44010.0000 |
Screw, Pan Head #8 x .50" |
29 |
|
29. |
39443.1003 |
Pad, Adhesive Back .75" Dia. |
|
|
30. |
38931.1002 |
Kit, Drip Tray (Includes item 31) |
|
P4166 |
31. |
38932.0000 |
Cover, Drip Tray |
|
|
|
|
|||
32. |
45457.0000* |
Decal, Do not Submerge |
|
|
33. |
39043.0002* |
Decal, Do not Spray |
|
30 |
34.39043.0001* Decal, Do not Submerge Server
35.42889.0000 Seal
36.35071.0000 Decal, Black Wrap 1.5 Gal. (Not Illustrated)
37974.0000 Decal, Black Wrap 1.0 Gal. (Not Illustrated)
37.35301.0001 Brush, Cleaning (Not Illustrated)
*Components of item 19
3 |
43240.9 030912 |
SERVER WITHOUT STAND
REPLACEMENT PARTS |
17 |
16 |
15 |
14 |
13 |
|
1.42554.1001 Display Kit, (Countup)(Includes items 2 - 4)
|
42826.1000 |
Screw, Thumb #6-32 x .25" |
12 |
28 |
|
2. |
46247.1000 |
Batteries, 4 Pack AAA |
|||
|
|
||||
3. |
42546.0001 |
Gasket, Battery Cover |
|
|
|
4. |
42547.0001 |
Cover, Battery |
|
|
|
|
02361.0000 |
Screw, Pan Head #4-40 x .25" |
|
|
|
5. |
43135.0000 |
Handle, Faucet |
|
|
|
6. |
29165.1002 |
Faucet Bonnet |
18 |
|
|
7. |
00601.1000 |
Faucet Spring (Package of 6) |
|
||
8. |
29164.1000 |
Faucet Stem (Package of 6) |
26 |
|
|
9. |
00600.1000 |
Faucet Seat Cup (Package of 6) |
|
||
10. |
42567.0000 |
Faucet Body |
19 |
|
|
11. |
42543.0000 |
Guard, Faucet |
|
||
|
35074.1000 |
Screw, Pan Head M4 x .7 x .25 |
27 |
|
|
|
43231.0000 |
Washer, M4 x 9MM |
|
||
12. |
42584.1000 |
Plug, Front (Package of 10) |
29 |
|
|
13. |
42818.1001 |
Sensor Assy, 1.0 Gal (Includes items 14 &15) |
|
||
|
42565.1000 |
Sensor Assy, 1.5 Gal (Includes items 14 &15) |
20 |
|
|
14. |
42563.1002 |
Cap |
|
||
15. |
39043.0000 |
Decal, Do Not Submerge |
21 |
|
|
16. |
42562.0000* |
Handle, Server |
|
||
17. |
42758.0000* |
Shoulder Screw |
22 |
|
|
18. |
42585.1000 |
Plug, Rear (Package of 10) |
|
||
19. |
43246.1000 |
Cover Assy, |
23 |
|
|
|
42761.0000* |
Screw, Pan Head M4 x 9 |
|
||
20. |
35710.0000 |
Decal, Warning Hot Liquid |
24 |
|
|
21. |
32591.1000 |
Tube, Silicone .50" ID x 12.0" (cut to length) |
|
||
22. |
28526.1000 |
Tube, Silicone .313" ID x 12.0" (cut to length) |
25 |
|
|
23. |
42912.0000 |
Foot, Rubber |
|
||
|
43163.0000 |
Screw, Pan Head #8 x .75" |
|
|
|
24. |
42295.0001 |
Elbow, 90° |
|
|
|
25. |
42890.1000 |
Base Cover |
|
|
26.45457.0000* Decal, Do not Submerge
27.39043.0002* Decal, Do not Spray
28.39043.0001* Decal, Do not Submerge Server
29.42889.0000 Seal
30.35071.0000 Decal, Black Wrap 1.5 Gal. (Not Illustrated)
37974.0000 Decal, Black Wrap 1.0 Gal. (Not Illustrated)
31.35301.0001 Brush, Cleaning (Not Illustrated)
*Components of item 19
STAND FOR SERVERS WITHOUT STAND
REPLACEMENT PARTS
-39795.0003 Stand, Assy (Includes items 1 - 8)
1. |
39449.0005 |
Bracket, Rear |
2. |
39448.0003 |
Bracket, Front |
3. |
38929.0002 |
Stand, Server |
4.00970.0000 Nut, Keps #8-32
5.38930.0002 Base Plate, Stand
44010.0000 |
Screw, Pan Head #8 x .50" |
6.39443.1003 Pad, Adhesive Back .75" Dia.
7. 38932.0000 |
Cover, Drip Tray |
8.38931.1002 Drip Tray Kit (Includes item 7)
2
1 |
3 |
|
4
5
6
1
2
3
4
5
6
7
8
9
10
11
7
8
4 |
43240.9 030912 |
|
DIGITAL DISPLAY
The Digital ThermoFresh® Server is equipped with a digital probe and display called a Digital Sight Gauge. The probe contains a circuit board designed to sense liquid levels & hold times. During the monitoring process, the probe sends information to the display. The display then allows the user to monitor the liquid level and freshness (hold time) of the beverage held in the server.
HORIZONTAL BAR
Using the Digital Sight Gauge display, the liquid level in the server can be |
|
monitored by watching the horizontal bars. The 1.0 gallon display is equipped with |
|
4 bars and the 1.5 gallon with 6 bars to represent the level inside the dispenser. |
|
(each bar represents a quart, or one quarter of a gallon) |
|
All four/six bars will be displayed when the server is full. When the level of |
|
the liquid drops to a certain level, the highest bar on the display will no longer be |
|
illuminated. These bars will continue to disappear as the level inside the dispens- |
|
er drops. (See Fig. 1) |
|
COUNT UP TIMER |
FIG. 1 |
The Digital display is set to count up to 4:00 hours. The display counts up in one minute increments, flashing at 2:00 hours and continuing to flash once it reaches 4:00 hours. (See Fig. 1)
TIMER RESET
The display will reset to 0 when any of the following occurs:
•The liquid level in the server is increased by 1 bar for a sustained period of time. (brewing into, or adding additional liquid to existing beverage)
•A fresh new beverage is brewed into the server.
•When the contact pins of the sensor assembly are disengaged from the display for more than 20 seconds.
DISPLAY OFF
When the sensor assembly on the server is removed or loosened for more than 20 seconds, the display on the Digital Sight Gauge breaks contact with the pins on the surface of the server. When this happens, the outline that surrounds the Horizontal Level Bars will flash on and off and the time disappears. This indicates that the display has been disengaged from the probe and cannot receive data.
When the display is in place and engaged, but the server is empty, the outline surrounding the Horizontal Level Bars will be on but not flashing and the Freshness Time will not be displayed. All other portions of the display will not be visible. This indicates the display is engaged and ready to receive data from the probe, but the server is empty.
The only time the display will be completely blank, is when the batteries have been removed or have expired. (See the “Battery Replacement” section for additional
information.) |
Flashing Notification Table |
||
|
Position |
Minutes |
|
FRESHNESS TIME |
0 |
30 |
|
1 |
60 |
||
This unit is factory set to count up to 2:00 hours, and begin flashing. If a reset condition |
|||
2 |
90 |
||
has not occurred, it will continue to flash and count up to a maximum of 4:00 hours. |
3 |
120 (Default) |
|
Flashing notification is adjustable and can be set between 15 minutes and 3 hours 45 |
4 |
150 |
|
5 |
180 |
||
minutes in 15 minute increments. Setting changed by opening battery compartment and |
|||
6 |
210 |
||
positioning rotary switch using a small screwdriver. Settings are defined in the Flashing |
|||
7 |
240 |
||
Notification Table. |
|||
8 |
15 |
||
|
|||
LOW BATTERY INDICATOR |
9 |
45 |
|
A |
75 |
||
When the batteries in the display unit are running low, the display is also equipped with |
B |
105 |
|
C |
135 |
||
a battery icon. The upper most bar used in monitoring liquid levels, will begin to flash in the |
|||
D |
165 |
||
shape of a battery to indicate that it is time to replace the batteries. (See FIG. 1) |
|||
E |
195 |
||
|
|||
|
F |
Disable Timer |
|
5 |
43240.9 030912 |
|
Loading...