BT SYNERGY 4000 User Manual

0 (0)

Synergy 4000 – Edition 1 – 8.05.06 – 7372

User Guide

BT SYNERGY 4000

BT SYNERGY 4000 User Manual

Synergy 4000 – Issue 2 – Edition 1 – 05.07.06 – 7699

2 Getting started

WARNING

Do not place your BT Synergy 4000 in the bathroom or other humid areas.

Handset range

The BT Synergy 4000 has a range of up to 300 metres outdoors when there is a clear line of sight between the base and handset. Any obstruction between the base and handset will reduce the range significantly. With the base indoors and handset either indoors or outdoors, the range will normally be up to 50 metres. Thick stone walls can severely affect the range.

Signal strength

The icon on your handset indicates when you are in range.

When you move out of range of the base, the out of range tone will sound every minute. This tone is repeated until you move back into range.

IMPORTANT

The charger must be plugged into the mains power socket at all times. Only use the power cable supplied with the product.

Location

You need to place your BT Synergy 4000 charger within 2 metres of a mains power socket so that the cable

will reach.

Make sure it is at least 1 metre away from other electrical appliances to avoid interference.

Your BT Synergy 4000 works by sending radio signals between the handset and base. The strength of the signal depends on where you site the base. Putting it as high as possible ensures the best signal.

Connect the charger to the mains power

1.Push the mains power cord into the power socket on the underside of the charger until you hear it click into place. Plug the other end into the mains power wall socket.

Power adaptor cable

If you experience any problems, please call the Helpline on 0870 605 8047 or email bt.helpdesk@suncorptech.com

Synergy 4000 – Issue 2 – Edition 1 – 05.07.06 – 7699

Charge the handset

1.Rechargeable batteries are already fitted in your handset. To activate the batteries, pull the plastic tab away from the bottom of the handset as shown.

and tab this Remove 24 for batteries charge use before hours

batteries Rechargeable fitted already

PULL

2. Place the handset on the charger to charge for at least 24 hours. The red Charging light comes on (this will stay on even when the batteries are fully charged). When the handset is fully charged the display shows the symbol.

Registering your handset to either your BT Synergy 4100 or 4500 base

If you are registering the handset to another DECT GAP compatible base station that is not a BT Synergy 4100 or 4500, please refer to the user guide for that base for registration instructions.

Before registration, make sure the handset batteries are fully charged and that you are close to the main base station.

Getting started

3

Talk/Standby time

In ideal conditions, fully charged handset batteries should give up to 10 hours talk time or up to 100 hours standby time on a single charge. The base must remain plugged in to the mains and switched on at all times.

Note that new batteries do not reach full capacity until they have been in normal use for several days.

Battery low warning

If the symbol flashes in the display and you hear a warning beep every 10-15 seconds, you will need to recharge the handset before you can use it again.

During charging, the symbol will scroll in the display.

Battery performance

To keep your batteries in the best condition, leave the handset off the base for a few hours at a time.

Running the batteries right down at least once a week will help them last as long as possible.

The charge capacity of rechargeable batteries will reduce with time as they wear out, giving the handset less talk/standby time. Eventually they will need to be replaced. New batteries are available from the BT Synergy 4000 Helpline on 0870 605 8047.

If you experience any problems, please call the Helpline on 0870 605 8047 or email bt.helpdesk@suncorptech.com

Synergy 4000 – Issue 2 – Edition 1 – 05.07.06 – 7699

4

Getting started

 

 

 

 

 

 

 

After charging your handset for the

At the base:

 

 

first time, subsequent charging time

1. Press and hold

for 10 seconds, until you hear a beep,

 

is about 6–8 hours a day. Batteries

 

and handset may become warm

then release it.

 

 

during charging. This is normal.

 

 

 

 

At the handset:

IMPORTANT

DECT GAP Profile only guarantees that basic calling functions will work correctly between different makes/types of handset and base. There is a possibility that certain services, such as Caller Display, will not work correctly.

The BT Synergy default base PIN is 0000.

2.Press Menu or Menu until Registration is displayed, then select the OK option.

3.Register Base is displayed select the OK option to confirm.

4.Use the keypad to enter the number of the base you want to register to (1 4), then select the OK option.

The display shows, e.g. Search for Base 2 (for base 2) and the icon flashes.

5.Enter your 4 digit PIN, then select the OK option. When the base is located, your handset display will be updated with the handset number for the selected base.

Using your phone

If you need further instructions on using your phone or require an explanation on any of the features, then please refer to your main BT Synergy 4100 or 4500 user guide.

If you require any further assistance, then please call the Helpline on 0870 605 8047 or email bt.helpdesk@suncorptech.com

If you experience any problems, please call the Helpline on 0870 605 8047 or email bt.helpdesk@suncorptech.com

Loading...
+ 8 hidden pages