Brother PT-110 User Manual

0 (0)

brother«

Printed in Japan

 

UN8173001

Please read this instruction leaflet before using the

P-Touch. Keep it in a handy place for future reference.

This model uses Brother's M-TAPE line (tape bearing

the logo).

MODEL:PT-110

YHth the P-Toitch Home& Hobby Ж you can маке labc!^ eiurpiy nmi en^ily. iii}uvly o~,i the P-Touch. keu in your ff/cssiiyc mdy/ess the Print key/You\cm mefourd^^^ oftexi, vm-iou^ si J//n-isrio'r;is boid, italic, undalinc.. MUI irnnie. .Vlessitycs can be an either ane or two lines. You caii alsa inchiiic |7Сй';Ь'о7 characters and special synihois in your message, biiv diffcreni tape color$4silver, ^oldy pink, green апФЫие) MUI -хоо xoidlhs ('9 rmn and 12 mm\ are агчп1аЫе.

FCC NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part IS of the FCC Rules. These limits are designed to

provide

reasonable

protection

against harmful

interference

in a

residential

instal­

lation,

This

equipment

generates, uses, and

can radiate

radio

frequency

energy

and, if

not

installed

and

used

in accordance with the Instructions,

may cause

harm­

ful interference to radio communications. However, there is no guarantee that in­

terference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or

television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the in­ terference by one or more of the following measures:

-Reorient or relocate the receiving antenna

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/television technician for help.

2)Remove the old batteries and insert six new AA size alkaline batteries, miaking sure that their orientation is as shown in the illustration engraved on the inside of the case. The three batteries on top all point in one direction, while the three underneath point in the opposite direction.

When inserting new batteries, always insert them posi­ tive end first. When removing old batteries, always remove them negative end first.

Always replace worn out ba tteries with brand new ones, and always replace all six at once.

Care and precautions

1)Use a soft dry cloth to clean the machine.

2)Use only AA size alkaline batteries.

3)Do not expose the machine or the tape cassette to high temperature, high humidity or excessive dust.

4)If you do not intend to use the machine for an extended period of time, remove the batteries.

5)Do not touch the cutter lever when printing or while replacing the cutter unit.

6)Do not touch the cutter blade.

7)Do not put the tapes in your mouth.

8)Do not stick tapes onto your skin.

Putting in the batteries

1)To remove the battery compartment cover, press down firmly on the triangular catch located on the end of the machine furthest from the tape cutter, and pull the battery compartment cover away from the P-Touch so that it disengages.

3)To replace the cover, fit the tabs on the cover into the slots in the P-Touch case and push down firmly on the catch at the opposite end of the cover so that the cover snaps securely back into place,

Accessories

The following accessories are availáblb:

Tape cassettes

1/2" (12mm)

 

 

$9.89 (SRP)

 

 

 

 

Black on silver

M-931

м-921

Black on gold

M-831

м-821

Black on blue

M-531

м-521

Black on green

M-731

М-721

Black on pink

M-E31

М-Е21

 

 

 

Replacement

TC7 $9.95 (SRP)

 

cutter unit

 

 

 

 

 

 

Most retailers and distributors carry a full line of tape cassettes. If you wish to order accessories for your P- Touch direct from Brother, please refer to the "Acces­ sory Order Form" included separately.

Changing the cutter unit

If the cutter becomes blunt and ceases to cut the tape cleanly, replace it.

1)Open the cassette compartment.

2)Grasp the tab on the cutter unit and lift it out, taking care not to touch the blade or the cutter lever.

3)Insert a new cutter unit. If the cutter lever is stuck in the pushed-in position, rotate the new cutter unit as you insert it, to push the lever back into its normal position.

CAUTION

When changing the cutter unit, be sure not to touch the cutter blade.

Make sure that small children do not try to put the cutter unit in their mouths.

Changing the tape cassette

1) To remove the tape cassette compartment cover, press the textured area of the catch located on the end of the machine closest to the tape cutter.

2)Press down firmly on the catch so that the cover hinges up, then remove it.

3)Lift out the old cassette. Remove the paper tab from the new tape cassette. Make sure that the end of the tape in the new cassette feeds through the guide posts on the cassette.

4)Insert the tape cassette, making sure that it clicks into place. Ensure that the cassette sits properly on the

two metal posts.

Tape exit slot

Rubber pinch roller

Metal post

5)To replace the cover, fit the tab on the cover into the slots in the P-Touch case and push down firmly on

the cover so that it snaps securely back mto place. 6) Hold down the 0> key and press the ^ key, then

cut the tape.

The amount of tape left is visible through the zvindoiv in the back of the P-Touch.

When there is only a little tape remaining, the tape becomes green.

Cleaning

If dust accumulates on the print head, one or more un­ printed horizontal lines may appear on your labels. Should this happen, clean the P-Touch as follows,

1) Turn off the P-Touch.

2) Open the cassette compartment and remove the cas­ sette.

3)Wipe the print head and pinch roller up and down using a dry cotton swab.

4) Replace the cassette, replace the cover, switch on, hold down the @ key and press the key to feed the tape, and try a test print.

5)If the tape is still speckled with dust, repeat steps 1-4, this time using a cotton swab dipped in rubbing alco­ hol.

Loading...
+ 2 hidden pages