Brother LS2300PRW Operation Manual

5 (1)
Brother LS2300PRW Operation Manual

IMPORTANT SAFETY INSTRUCTIONS

When using the sewing machine, basic safety precautions should always be followed, including the following:

“Read all instructions before using.” DANGER – To reduce the risk of electric shock:

1.The sewing machine should never be left unattended when plugged in. Always unplug this sewing machine from the electrical outlet immediately after using and before cleaning.

2.Always unplug before changing the light bulb. Replace bulb with same type rated 15 watts.

WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons:

1.Do not allow this machine to be used as a toy. Close attention is necessary when the sewing machine is used by or near children.

2.Use this sewing machine only for its intended use as described in this manual. Use only accessories recommended by the manufacturer as contained in this manual.

3.Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the sewing machine to the nearest authorized dealer or service center for examination, repair, electrical or mechanical adjustment.

4.Never operate the sewing machine with any of the air openings blocked. Keep the ventilation openings of the sewing machine and foot controller free from the accumulation of lint, dust and loose cloth.

5.Never drop or insert any object into any openings.

6.Do not use this machine outdoors.

7.Do not operate this machine where aerosol (spray) products are being used or where oxygen is being administered.

8.To disconnect, turn the main switch to the symbol “O” position which represents off, then remove plug from outlet.

9.Do not unplug by pulling on the cord. To unplug, grasp the plug and pull, not the cord. 10.Keep fingers away from all moving parts. Special care is required around the

sewing machine needle.

11.Always use the proper needle plate. The wrong plate can cause the needle to break. 12.Do not use a bent needle.

13.Do not pull or push the fabric while stitching. It may deflect the needle causing it to break.

14.Switch the sewing machine to the off, symbol “O” position when making any adjustments in the needle area, such as threading the needle, changing the needle, threading the bobbin, or changing the presser foot.

15.Always unplug the sewing machine from the electrical outlet when removing covers, lubricating, or when making any other user service adjustments mentioned in this instruction manual.

16.This sewing machine is not intended for use by young children or impaired persons without supervision.

1

17.Young children should be supervised to ensure that they do not play with this sewing machine.

SAVE THESE INSTRUCTIONS

This sewing machine is intended for household use.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

CONGRATULATIONS ON CHOOSING OUR MACHINE

To fully enjoy all the features, we suggest that you study the manual before using the machine.

PLEASE READ BEFORE USING THIS MACHINE

For safe operation

1.Be sure to keep your eye on the needle while sewing. Do not touch the handwheel, thread takeup lever, needle, or other moving parts.

2.Remember to turn off the power switch and unplug the cord when:

Operation is completed

Replacing or removing the needle or any other parts

A power failure occurs during use

Maintaining the machine

Leaving the machine unattended

3.Do not store anything on the foot controller.

4.Plug the machine directly into the wall. Do not use extension cords.

For a longer service life

1.When storing this machine, avoid direct sunlight and high humidity locations. Do not use or store the machine near a space heater, iron, halogen lamp, or other hot objects.

2.Use only neutral soaps or detergents to clean the case. Benzene, thinner, and scouring powders can damage the case and machine, and should never be used.

3.Do not drop or hit the machine.

4.Always consult the operation manual when replacing or installing any assemblies, the presser feet, needle, or other parts to assure correct installation.

For repair or adjustment

In the event a malfunction occurs or adjustment is required, first follow the troubleshooting table in the back of the operation manual to inspect and adjust the machine yourself. If the problem persists, please consult your local authorized Brother dealer.

For additional product information and updates, visit our web site at www.brother.com

The contents of this manual and specifications of this product are subject to change without notice.

FOR USERS IN THE UK, EIRE, MALTA AND CYPRUS ONLY IMPORTANT

In the event of replacing the plug fuse, use a fuse approved by ASTA to BS 1362, i.e. carrying the mark, rating as marked on plug.

Always replace the fuse cover. Never use plugs with the fuse cover omitted.

If the available electrical outlet is not suitable for the plug supplied with this equipment, you should contact your authorized dealer to obtain the correct lead.

2

——————————————————————————————————————————————————————————

CONTENTS

 

CONTENTS .........................................................................................................................

3

1. KNOWING YOUR SEWING MACHINE ..........................................................

5

NAMES OF MACHINE PARTS AND THEIR FUNCTIONS ....................................................

5

The main parts .................................................................................................................................................

5

Needle and presser foot section ......................................................................................................................

6

Flat bed attachment .........................................................................................................................................

6

ACCESSORIES .....................................................................................................................

7

OPTIONAL ACCESSORIES ..................................................................................................

7

USING YOUR SEWING MACHINE .....................................................................................

8

Power supply precautions ................................................................................................................................

8

Power supply ....................................................................................................................................................

8

Foot controller ..................................................................................................................................................

9

Steadying the machine .....................................................................................................................................

9

THREADING THE MACHINE ............................................................................................

10

Winding the bobbin ........................................................................................................................................

10

Lower threading .............................................................................................................................................

11

Upper threading .............................................................................................................................................

13

Drawing up the lower thread ..........................................................................................................................

14

REPLACING THE NEEDLE .................................................................................................

15

Needle precautions ........................................................................................................................................

15

Selecting the needle depending on the thread and fabric types ....................................................................

15

Checking the needle ......................................................................................................................................

16

Replacing the needle .....................................................................................................................................

16

Sewing with a twin needle (Option) ................................................................................................................

18

REPLACING THE PRESSER FOOT ......................................................................................

19

Replacing the presser foot .............................................................................................................................

19

Removing the presser foot holder ..................................................................................................................

20

2. SEWING BASICS ...........................................................................................

21

SEWING ............................................................................................................................

21

General sewing procedure .............................................................................................................................

21

Stitch width knob ............................................................................................................................................

22

Stitch length knob ...........................................................................................................................................

22

Needle position selector .................................................................................................................................

22

Starting to sew ...............................................................................................................................................

23

Sewing in reverse ...........................................................................................................................................

23

Thread tension ...............................................................................................................................................

24

USEFUL SEWING TIPS ......................................................................................................

25

Trial sewing ....................................................................................................................................................

25

Changing the sewing direction .......................................................................................................................

25

Sewing curves ................................................................................................................................................

25

Sewing thick fabrics .......................................................................................................................................

25

Sewing thin fabrics .........................................................................................................................................

26

Sewing stretch fabrics ....................................................................................................................................

26

Using a free-arm style ....................................................................................................................................

26

3

3. UTILITY STITCHES ........................................................................................

27

USEFUL STITCHES ............................................................................................................

27

Zigzag stitches ...............................................................................................................................................

27

Basic stitching ................................................................................................................................................

27

Blind hem stitching .........................................................................................................................................

28

Darning ...........................................................................................................................................................

29

Over edge stitch .............................................................................................................................................

29

BUTTONHOLE SEWING/ BUTTON SEWING ...................................................................

30

Buttonhole sewing ..........................................................................................................................................

30

Button sewing .................................................................................................................................................

31

ZIPPER INSERTION ...........................................................................................................

33

APPLIQUÉ, MONOGRAMMING AND EMBROIDERING .................................................

34

Appliqués .......................................................................................................................................................

34

Monogramming and embroidering .................................................................................................................

34

DECORATIVE STITCHING ................................................................................................

36

Gathering .......................................................................................................................................................

36

Satin stitches ..................................................................................................................................................

36

Attaching the lace ...........................................................................................................................................

37

Cording ...........................................................................................................................................................

37

4. APPENDIX .....................................................................................................

38

MAINTENANCE ................................................................................................................

38

Oiling ..............................................................................................................................................................

38

Changing the bulb ..........................................................................................................................................

38

Cleaning the machine surface ........................................................................................................................

39

Cleaning the shuttle race ...............................................................................................................................

39

Cleaning the feed dogs ..................................................................................................................................

40

Bobbin case tension adjustment ....................................................................................................................

41

TROUBLESHOOTING .......................................................................................................

42

When the thread is entangled ........................................................................................................................

45

INDEX ...............................................................................................................................

46

4

KNOWING YOUR SEWING MACHINE —————————————————————————————————————————

1 KNOWING YOUR SEWING MACHINE

NAMES OF MACHINE PARTS AND THEIR FUNCTIONS

The main parts

aNeedle position selector (page 22)

Shift this lever to select needle position.

bStitch width knob (page 22)

Turn this knob to set the stitch width.

c Thread take-up lever (page 13)

d Flat bed attachment with accessory storage (page 6 and 26)

eUpper tension control dial (page 24)

This controls the tension of the upper thread.

fStitch length knob (page 22)

Turn this knob to set the stitch length.

gReverse sewing lever (page 23)

Press and hold down the reverse sewing lever to sew in the opposite direction.

h Built-in handle

iSpool pin (page 10 and 13)

The spool pin holds the spool of thread.

jBobbin winder (page 10)

The bobbin winder winds thread onto the bobbin for use as the lower thread.

kHandwheel

Use the handwheel to manually raise and lower the needle.

lMain power/sewing light switch (page 8)

Use this switch to turn on and off the main power and sewing light.

mFoot controller jack

Insert the foot controller plug into the foot controller jack, which also supplies power to this machine.

nThread cutter (page 23)

Pass the threads through the thread cutter to cut them.

oPresser foot lever (page 13)

Use the presser foot lever to raise and lower the presser foot.

pBobbin winding pre-tension disc/thread guide (page 10 and 13)

The thread guide/bobbin winding pre-tension disc is used when winding the thread onto the bobbin and threading the machine.

qFoot controller (page 9)

Use the foot controller to control the sewing speed and to start and stop sewing.

Part code;

XC7359-021 (110/120V Area), XC7438-421 (220/240V Area), XC7456-421 (U.K.), XE0629-001 (Australia, New Zealand), XD0852-021 (Korea), XC7438-421 (Russia), XD0112-121 (Argentina), XE3414-001 (Brazil(120V)), XE4302-001 (Brazil(220V)),XE3447-001 (Taiwan)

5

Needle and presser foot section

aPresser foot holder assembly

The presser foot is installed onto the presser foot holder assembly.

bPresser foot screw

Use the presser foot screw to hold the presser foot holder assembly in place.

cPresser foot (Zigzag)

The presser foot applies pressure consistently on the fabric as the sewing takes place. Attach the appropriate presser foot for the selected stitching.

dFeed dogs

The feed dogs feed the fabric in the sewing direction.

eNeedle plate

The needle plate is marked with guides for sewing straight seams.

f Shuttle hook

gShuttle cover

Open the shuttle cover to set the bobbin.

h Bobbin case i Needle

j Needle bar thread guide

kNeedle clamp screw

Use the needle clamp screw to hold the needle in place.

Flat bed attachment

The accessories are stored in a compartment inside the flat bed attachment.

aLift the bottom of the flat bed attachment 1 toward you, and then pull the flat bed

attachment out to remove it.

a Flat bed attachment b Storage compartment

Note

Put the accessories in the bag, and then store the bag inside the compartment. If the accessories are not in a bag, they may fall out, and be lost or damaged.

6

KNOWING YOUR SEWING MACHINE —————————————————————————————————————————

ACCESSORIES

The following accessories are stored in the flat bed attachment. We have designed these accessories to help you be able to carry out most sewing tasks.

Note

(For U.S.A. only)

Foot controller: Model KD-1902, N

This foot controller can be used on the following machine models: LS-2000/LS2250PRW/LS2300PRW.

The screw of the presser foot holder is available through your authorized dealer. (Part code: 132730-122)

A replacement for the factory-installed presser foot is available through your authorized dealer. (Part number: 138135-122)

1.

2.

3.

4.

90/14 needle

No.

Part Name

 

Part Code

 

No.

Part Name

 

Part Code

 

 

 

 

Americas

 

Others

 

 

 

Americas

Others

1

Zipper foot “I”

X59370-021 (LS-2000/LS2250PRW)

3

Bobbin

SA156 (Americas)

SFB:

XE9369-001 (Others)

 

SABOBBIN (U.S.A. only)

XA5539-151

 

 

 

 

 

 

 

2

Darning plate

XA3442-121

 

4

Needle set

XE7064-001

 

OPTIONAL ACCESSORIES

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1.

 

 

2.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

No.

Part Name

 

Part Code

 

 

 

 

Americas

 

Others

1

Extra spool pin

130920

-021

2

Twin needle

131096-121

7

USING YOUR SEWING MACHINE

Power supply precautions

1

 

Be sure to observe the following precautions concerning the power supply.

WARNING

Use only regular household electricity for the power source. Using other power sources may result in fire, electric shock, or damage to the machine.

Turn off the main power and remove the plug in the following circumstances:

When you are away from the machine

After using the machine

When the power fails during use

When the machine does not operate correctly due to a bad connection or a disconnection

During electrical storms

CAUTION

Do not use extension cords or multi-plug adapters with many other appliances plugged in to them. Fire or electric shock may result.

Do not touch the plug with wet hands. Electric shock may result.

When unplugging the machine, always turn off the main power first. Always grasp the plug to remove it from the outlet. Pulling on the cord may damage the cord, or lead to fire or electric shock.

Do not allow the power cord to be cut, damaged, modified, forcefully bent, pulled, twisted, or bundled. Do not place heavy objects on the cord. Do not subject the cord to heat. These things may damage the cord and cause fire or electric shock. If the cord or plug is damaged, take the machine to your authorized dealer for repairs before continuing use.

Unplug the power cord if the machine is not to be used for a long period of time. Otherwise a fire may result.

Power supply

aInsert the foot controller plug, located between the foot controller and the power supply plug on the cord, into the jack on the machine. Then, insert the power supply plug into a wall outlet.

bSet the main power switch to “I”.

The sewing lamp comes on when the machine is turned on.

1

a Foot controller plug

8

KNOWING YOUR SEWING MACHINE —————————————————————————————————————————

cTo turn off the machine, set the main power switch to “ ”.

The sewing lamp goes off when the machine is turned off.

Note

If a power outage occurs while the sewing machine is being operated, turn off the sewing machine and unplug the power

supply cord. When restarting the sewing machine, follow the necessary procedure to correctly operate the machine.

(For U.S.A. only)

This appliance has a polarized plug (one blade wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug.

If it still does not fit, contact a qualified electrician to install the proper outlet. Do not modify the plug in any way.

Foot controller

CAUTION

When connecting the foot controller, be sure to turn off the sewing machine in order to prevent the machine from accidentally being started.

When you press the foot controller down lightly, the machine will run at a low speed. When you press harder, the machine’s speed will increase. When you take your foot off the foot controller, the machine will stop.

Slower

Faster

You should make sure that nothing is placed on the foot controller when the machine is not in use.

CAUTION

Do not allow pieces of cloth and dust to build up on the foot controller. Doing so could cause a fire or an electric shock.

A new sewing machine or one that has not been in use for a long period of time should be oiled as described on page 38. After oiling, be sure to wipe off any excess oil.

Steadying the machine

If the sewing machine has been placed on an uneven surface, turn the rubber cushion in the right-front corner of the base plate to adjust its height until the sewing machine is stable.

9

THREADING THE MACHINE

Winding the bobbin

1

 

This section describes how to wind the thread onto the bobbin.

1 Pulling it in as far as possible.

a Pre-tension disk

b Bobbin winder shaft c Bobbin

CAUTION

Only use bobbins (part code: SA156, SABOBBIN, SFB: XA5539-151) that have been designed for this sewing machine. Using other bobbins may cause damage to the machine.

We designed the bobbin that comes with this machine. If you use bobbins from other models, the machine will not work properly. Only use the bobbin that comes with this machine or bobbins of the same type (part code: SA156, SABOBBIN, SFB: XA5539-151).

Actual size

 

 

 

 

 

 

 

 

 

This model

 

Other models

a 11.5 mm (7/16 inches)

 

 

aPull up the spool pin as far as possible, and then put a spool of thread on this pin.

bPass the thread around the pre-tension disk.

CAUTION

If the spool of thread is not in the right place, the thread may tangle on the spool pin.

cPass the end of the thread through the hole on the bobbin from the inside of the bobbin.

dPut the bobbin onto the bobbin winder shaft and slide the bobbin winder shaft to the right. Turn the bobbin clockwise, by hand, until the spring on the shaft slides into the groove of the bobbin.

eTurn on the sewing machine.

fWhile holding the end of the thread, gently press the foot controller to wind the thread around the bobbin a few times. Then stop the machine.

a Spring on the shaft b Groove of the bobbin

10

KNOWING YOUR SEWING MACHINE —————————————————————————————————————————

gTrim the excess thread above the bobbin.

CAUTION

Make sure you follow the instructions carefully. If you do not cut the thread completely, and the bobbin is wound, when the thread runs low it may tangle around the bobbin and cause the needle to break.

hPress the foot controller to start.

iWhen the bobbin seems full and begins spinning slowly, take your foot off the foot controller.

jCut the thread, slide the bobbin winder shaft to the left and remove the bobbin.

Memo

When the sewing machine is started or the handwheel is turned after winding the thread around the bobbin, the machine will make a clicking sound; this is not a malfunction.

The needle bar does not move when you slide the bobbin winding shaft to the right.

CAUTION

Winding the bobbin improperly may cause the thread tension to loosen, breaking the needle and resulting in injury.

Lower threading

Install the bobbin wound with thread.

CAUTION

Winding the bobbin improperly may cause the thread tension to loosen, breaking the needle and resulting in injury.

12

a Wound evenly

bWound poorly

The bobbin was designed specifically for this sewing machine. If bobbins from other models are used, the machine will not operate correctly. Use only the enclosed bobbin or bobbins of the same type (part code: SA156, SABOBBIN, SFB: XA5539-151).

Actual size

This model

Other models

a11.5 mm (7/16 inches)

Make sure you turn the power off while threading the machine. If you accidentally step on the foot controller and the machine starts to sew, you could be injured.

-“ Moving parts - To reduce the risk of injury. Disconnect from supply circuit before servicing. Remove cover.”

aRaise the needle to its highest position by turning the handwheel toward you (counterclockwise) and raise the presser foot lever.

12

a Wound evenly b Wound poorly

11

bOpen the shuttle cover behind the flat bed attachment at the front of the machine.

a Flat bed attachment b Shuttle cover

cRemove the bobbin case by pulling its latch toward you and pulling it out from the shuttle race.

a Bobbin case latch

dUnwind about 10 cm (4 inches) of thread from a full bobbin, and then insert the bobbin into the bobbin case.

Only use bobbins that were designed to be used with this machine.

CAUTION

Make sure you set the bobbin so the thread unrolls in the right direction. If the thread unrolls in the wrong direction, it may cause the thread tension to be incorrect or break the needle.

ePull the trailing thread through the slot, down and to the left, as shown below, until it enters the delivery eye under the tension spring.

1

a Tension spring

fHold the bobbin case by the latch, fully insert the bobbin case into the shuttle race, and then release the latch.

Make sure the bobbin case finger fits into the notch at the top of the shuttle race.

a Bobbin case finger b Notch

gClose the shuttle cover.

CAUTION

Make sure that the bobbin case is properly placed back into the machine. If it is incorrectly installed, it will fall out from the shuttle when the machine starts to sew.

12

KNOWING YOUR SEWING MACHINE —————————————————————————————————————————

Upper threading

Set the upper thread and thread the needle.

a Spool pin

b Thread guide (rear) c Thread guide (front) d Thread take-up lever

CAUTION

Make sure you thread the machine properly. Otherwise, the thread could tangle and break the needle.

aRaiselever. the presser foot using the presser foot

a Presser foot lever

bRaise the needle by turning the handwheel toward you (counterclockwise) to raise the thread take-up lever to its highest position.

cPull up the spool pin as far as possible, and then put a spool of thread on this pin.

CAUTION

If the spool of thread is in the wrong place, or is set incorrectly, the thread may tangle on the spool pin and cause the needle to break.

dFeed the upper thread through both thread guides: the rear one first, then the front one.

ePull the thread down and around the upper tension control dial from the right to the left so the thread picks up the thread check spring.

If the needle is not correctly raised, the sewing machine can not be threaded. Be sure to turn the handwheel before threading the sewing machine.

a Upper tension control dial b Thread check spring

13

fWhile holding the thread as shown below, pull it between the tension discs.

gGuide the thread through the thread take-up lever from right to left.

a Thread take-up lever

hPut the thread behind the needle bar thread guide above the needle.

The thread can easily be passed behind the needle bar thread guide by holding the thread in your left hand, then feeding the thread with your right hand.

a Needle bar thread guide

iThread the needle from front to back and pull out about 5 cm (2 inches) of thread.

a 5 cm (2 inches)

Note

If the thread take-up lever is lowered, the upper thread cannot be wrapped around the thread take-up lever. Make sure you raise the presser foot lever and the thread take-up lever before you feed the upper thread.

If you incorrectly feed the thread you may cause sewing problems.

Drawing up the lower thread

aLightly hold the end of the upper thread.

1

a Upper thread

bWhile holding the end of the upper thread, raise the needle to its highest position by turning the handwheel toward you (counterclockwise).

cPullthread.on the upper thread to draw up the lower

a Upper thread b Lower thread

dPull out about 15 cm (6 inches) of both threads and pull them toward the back of the machine under the presser foot.

a Upper thread b Lower thread

14

KNOWING YOUR SEWING MACHINE —————————————————————————————————————————

REPLACING THE NEEDLE

This section provides information on sewing machine needles.

Needle precautions

Be sure to observe the following precautions concerning the handling of the needle. Failure to observe these precautions is extremely dangerous. Be sure to read and carefully follow the instructions below.

CAUTION

Only use home sewing machine needles. Use of any other needle may bend the needle or damage the machine.

Never use bent needles. Bent needles can easily break, possibly resulting in injury.

Selecting the needle depending on the thread and fabric types

The sewing machine needle that should be used depends on the fabric and thread thickness. Refer to the following table when choosing the thread and needle appropriate for the fabric that you wish to sew. Use the same size thread for the upper (spool) and lower (bobbin) threads.

 

Sewing fabrics

Needle sizes

Thread sizes

 

 

 

Fine tricot, Fine lace,

 

Cotton: 80

Very thin

 

 

Synthetic/ Polyester Long

 

Thin linen, Silk,

65/9

 

Fiber

 

 

Organza, Chiffon

 

 

 

 

Fine Mercerized Cotton

 

 

 

 

 

 

 

 

Cotton: 60-80

Lightweight

 

Voile, Taffeta,

75/11

Silk: “A”

 

Synthetic/ Polyester Long

 

Synthetics, Silk, Batiste

 

 

 

Fiber

 

 

 

 

 

 

 

 

Mercerized 50

 

 

Cotton, Gingham,

 

Cotton: 50-60

 

 

Poplin, Percale, Pique,

 

 

 

 

Silk: “A”

Medium weight

 

Satin, Velvet,

90/14 (Supplied with

 

Synthetic/ Polyester Long

 

Lightweight wool,

your machine.)

 

 

Fiber

 

 

Fine corduroy, Suitings,

 

 

 

 

Mercerized 50-60

 

 

Linen, Muslin

 

 

 

 

 

Heavyweight

 

Denim, Gabardine,

 

Cotton: 40-50

 

Tweed, Corduroy,

100/16

Mercerized Heavy Duty

 

 

Canvas, Duck

 

Polyester Long Fiber

Knits

 

Single knit, Double knit,

 

Cotton Wrapped

 

90/14 (Ball point)

Polyester

 

 

Jersey, Tricot

 

Polyester Long Fiber

 

 

 

 

 

 

 

 

 

Memo

The smaller the thread number, the thicker the thread; and the larger the needle number, the thicker the needle.

Use the ball point needle when sewing on stretch fabrics or fabrics where skipped stitches easily occur.

Use a 90/14 to 100/16 needle with transparent nylon threads, regardless of the fabric being sewn.

A 75/11 needle is already installed when the sewing machine is purchased.

15

CAUTION

The appropriate fabric, thread and needle combinations are shown in the table on the previous page. If the combination of the fabric, thread and needle is not correct, particularly when sewing thick fabrics (such as denim) with thin needles (such as 65/9 to 75/11), the needle may bend or break. In addition, the stitching may be uneven or puckered or there may be skipped stitches.

Checking the needle

Sewing with a bent needle is extremely dangerous since the needle may break while the machine is being operated.

Before using the needle, place the flat side of the needle on a flat surface and check that the distance between the needle and the flat surface is even.

1

2

a Flat side

bNeedle type marking

Correct needle

1

aFlat surface

Incorrect needle

If the distance between the needle and the flat surface is not even, the needle is bent. Do not use a bent needle.

1

a Flat surface

Replacing the needle

Replace the needle as described below. Use a coin and a needle that has been determined to be straight

according to the instructions in “Checking the 1 needle” .

aTurn off the sewing machine.

CAUTION

Before replacing the needle, be sure to turn off the sewing machine, otherwise injuries may occur if the foot controller is accidentally pressed and the machine starts sewing.

bRaise the needle to its highest position by turning the handwheel toward you (counterclockwise).

cLower the presser foot lever.

a Presser foot lever

16

KNOWING YOUR SEWING MACHINE —————————————————————————————————————————

dHold the needle with your left hand, and then use a coin to turn the needle clamp screw counterclockwise to remove the needle.

Note

The needle can be removed by simply loosening the needle clamp screw about one turn. (If the needle clamp screw is loosened too much, the needle clamp (which holds the needle) may fall off. Therefore, do not loosen the needle clamp screw too much.)

a Coin

b Needle clamp screw

Do not apply strong force when loosening or tightening the needle clamp screw, otherwise certain parts of the sewing machine may be damaged.

fWhile holding the needle with your left hand, use the coin to tighten the needle clamp screw by turning it clockwise.

Install the twin needle in the same way.

CAUTION

Be sure to insert the needle until it touches the needle stopper and securely tighten the needle clamp screw with a coin, otherwise the needle may break or damage may result.

eWith the flat side of the needle toward the rear of the machine, insert the needle until it touches the needle stopper.

a Needle stopper

17

Sewing with a twin needle (Option)

We have designed your machine so you can sew with the optional twin needle and two top threads. You can use the same color or two different colors of thread for making decorative stitches.

1

CAUTION

Use only twin needles that have been made for this machine (part code: 131096-121). Other needles could break, and damage the machine.

Do not sew with bent needles. The needle could break and injure you.

Use the zigzag presser foot.

Use a setting of less than 3 on the stitch width knob.

Set the needle position selector to M.

Slowly turn the handwheel toward you (counterclockwise) and check that the needle does not touch the presser foot. If the needle hits the presser foot, the needle may bend or break.

When changing the sewing direction, be sure to raise the needle before turning the fabric. If the fabric is turned while the needle is lowered, the needle may bend or break.

Twin needle threading

aAttach the twin needle.

Attach the twin needle in the same way as a single needle (page 16).

bAttach the optional extra spool pin.

Put the extra spool pin in the hole on the top of the machine. Put the second spool of thread onto the extra spool pin.

a First spool b Second spool

cUse the thread from the first spool to thread the machine to the needle bar thread guide.

The path for threading the machine to the needle bar thread guide is the same as for normally threading the machine (for a single needle). See page 13 for more details.

dThread the left needle from front to back.

eUse the thread from the second spool to thread the machine to the thread take-up lever.

The path for threading the machine to the thread take-up lever is the same as for normally threading the machine (for a single needle). See page 13 for more details.

fThread the right needle from front to back.

Do not pass the thread behind the needle bar thread guide.

aLeft needle thread passes through the needle bar thread guide.

bRight needle thread passes in front of the needle bar thread guide.

c Needle bar thread guide

18

KNOWING YOUR SEWING MACHINE —————————————————————————————————————————

REPLACING THE PRESSER FOOT

CAUTION

Always turn off the power before you change the presser foot. If you leave the power on and step on the controller, the machine will start and you may be injured.

Always use the correct presser foot for the stitch pattern you have chosen. If you use the wrong presser foot, the needle may strike the presser foot and bend or break, and may cause injury.

Only use presser feet that have been designed to be used with this machine. Using other any presser feet may cause an accident or injury.

Replacing the presser foot

Replace the presser foot as described below.

aIfturntheitsewingoff. machine has been turned on,

CAUTION

Before replacing the presser foot, be sure to turn off the sewing machine, otherwise injuries may occur if the foot controller is accidentally pressed and the machine starts sewing.

bRaise the needle to its highest position by turning the handwheel toward you (counterclockwise).

cRaise the presser foot lever.

dPress the black button at the back of the presser foot holder to release the presser foot.

a Black button

b Presser foot holder

ePlace a different presser foot below the holder so that the presser foot pin is aligned with the shank in the holder.

Position the presser foot so the letter indicating the presser foot type (A, I, etc.) is positioned to be read.

a Presser foot holder b Shank

c Pin

fSlowly lower the presser foot lever so that the presser foot pin snaps into the shank in the presser foot holder.

a Presser foot lever

a Presser foot lever

 

The presser foot is attached.

19

gRaise the presser foot lever to check that the presser foot is securely attached.

Removing the presser foot holder

Remove the presser foot holder when cleaning the sewing machine or when installing a presser foot that does not use the presser foot holder. Use a coin to remove the presser foot holder.

Removing the presser foot holder

a Remove the presser foot.

For details, refer to “Replacing the presser foot” (page 19).

b Use a coin to loosen the presser foot holder screw.

a Coin

b Presser foot holder

c Presser foot holder screw

Attaching the presser foot holder

aAlign the presser foot holder with the lowerleft side of the presser bar.

1

a Presser foot holder b Presser bar

b Hold the presser foot holder in place with your right hand, and then tighten the screw using a coin in your left hand.

a Coin

b Presser foot holder

c Presser foot holder screw

Note

If the presser foot holder is not correctly installed, the thread tension will be incorrect.

20

SEWING BASICS ———————————————————————————————————————————————————

2 SEWING BASICS

SEWING

Basic sewing operations are described below.

Before operating the sewing machine, read the following precautions.

CAUTION

While the machine is in operation, pay special attention to the needle location. In addition, keep your hands away from all moving parts such as the needle and handwheel, otherwise injuries may occur.

Do not pull or push the fabric too hard while sewing, otherwise injuries may occur or the needle may break.

Never use bent needles. Bent needles can easily break, possibly resulting in injuries.

Make sure that the needle does not strike basting pins, otherwise the needle may break or bend.

General sewing procedure

Follow the basic procedures below to sew.

1

Turn on the

Turn on the sewing machine.

machine.

For details on turning on the machine, refer to “Power supply” (page 8).

 

 

 

 

 

 

 

 

 

2

Select the stitch.

Select the stitch appropriate for the area to be sewn.

For details on selecting a stitch, refer to “Stitch width knob” (page 22).

 

 

 

 

 

 

 

 

 

 

3

Attach the presser

Attach the presser foot appropriate for the stitch.

For details on replacing the presser foot, refer to “Replacing the presser

foot.

 

foot” (page 19).

 

 

 

 

 

 

 

 

 

 

4

Start sewing.

Position the fabric, and then start sewing. When sewing is finished, cut the

threads.

 

 

For details on starting to sew, refer to “Starting to sew” (page 23).

 

 

 

21

Stitch width knob

The width of the zigzag stitch is regulated by operating the stitch width knob. The numbers above the knob represent the stitch width in millimeters (mm). The larger numbers set a wider stitch width. When the knob is set at 0, a straight stitch is sewn.

a Stitch width knob

Note

Do not move the knob while the needle is in the fabric.

When using the twin needle, the knob should always be set below 3.

Stitch length knob

The stitch length is regulated by turning this knob. The numbers above the knob represent the stitch length in millimeters (mm).

The larger numbers set a longer stitch length. When the knob is set to 0, the fabric is not fed. This setting is used for sewing on a button.

The F area is used for making a Satin Stitch (a close zigzag stitch), which can be used in making buttonholes and decorative stitches. The position needed for making the Satin Stitch may need to be adjusted according to the fabric and thread being used. To determine the correct knob position, first test the length settings on a fabric scrap.

a Stitch length knob

2

b Shorter

c Longer

 

Needle position selector

By shifting this lever to L (left), M (middle) or R (right), you can sew straight and zigzag stitches on the baseline.

When you sew close to the edge of the fabric, select L or R so the fabric is fed more easily.

This selector should be set at M (middle) for almost all stitches, but set it to other positions for the following applications.

1.Buttonhole sewing (see “Buttonhole sewing” on page 30.)

2.Button sewing (see “Button sewing” on page 31.)

3.Satin stitches (see “Satin stitches” on page 36.)

Note

Do not move the selector while the needle is in the fabric.

Always set the selector to M when using the twin needle.

22

bTolever.sew forward, release the reverse sewing
Press and hold down the reverse sewing lever while sewing.
a
(counterclockwise).
jRaise the presser foot lever.
kPull the fabric to the left side of the machine, and then pass the threads through the thread cutter on the back of the presser foot bar to cut them.
a Thread cutter
Sewing in reverse
Reverse sewing is used to lock the threads at the end of the seam or wherever reinforcement is needed.
Raise the needle to its highest position by turning the handwheel toward you
i
a Presser foot lever
gSlowly press down on the foot controller.
The machine starts sewing. hTake your foot off the foot controller.
The machine stops sewing.
Lower the presser foot lever.
f
———————————————————————————————————————————————————

SEWING BASICS

Starting to sew

aTurn on the sewing machine.

bRaise the needle to its highest position by turning the handwheel toward you (counterclockwise).

cRaise the presser foot lever.

a Presser foot lever

dPlace the fabric under the presser foot, pass the thread under the presser foot, and then pull out about 5 cm (2 inches) of thread toward the rear of the machine.

a 5 cm (2 inches)

eWhile holding the end of the thread and the fabric with your left hand, turn the handwheel toward you (counterclockwise) with your right hand to lower the needle to the starting point of the stitching.

23

Thread tension

The thread tension will affect the quality of your stitches. You may need to adjust it when you change fabric or thread.

Memo

Before beginning to change tension adjustments make sure the upper thread and bobbin are inserted correctly.

We recommend you do a test sample on a scrap of fabric before you start to sew.

Correct tension

Correct tension is important as too much or too little tension will weaken your seams or cause puckers on your fabric.

 

1

 

a Wrong side

2

b Surface

 

c Upper thread

 

d Lower thread

3

4

Upper tension is too tight

Loops appear on the surface of the fabric.

Note

If the bobbin thread was incorrectly inserted, the upper thread may be too tight. In this case, refer to “Lower threading” (page 11) and reinsert the bobbin.

 

1

 

 

 

a Wrong side

 

 

b Surface

2

 

c Upper thread

 

d Lower thread

 

 

 

 

e Loops appear on

3

5

surface of fabric

 

4

Solution

Reduce the tension by turning the upper tensioncontrol dial to a lower number.

Upper tension is too loose

Loops appear on the wrong side of the fabric.

Note

If the upper thread was incorrectly threaded, the upper thread may be too loose. In this case, refer to “Upper threading” (page 13) and rethread.

1

5

2

 

 

 

 

a Wrong side

 

 

b Surface

2

 

c Upper thread

 

d Lower thread

 

 

 

 

e Loops appear on

3

4

Solution

Increase the tension by turning the upper tensioncontrol dial to a higher number.

wrong side of fabric

Bobbin tension is too loose

Loops may appear on the surface of the fabric when sewing thin fabric with thin thread.

 

1

 

 

 

a Wrong side

 

 

b Surface

2

 

c Upper thread

 

d Lower thread

 

 

 

 

e Loops appear on

3

5

surface of fabric

 

4

Solution

Reduce the tension by turning the upper tensioncontrol dial to a lower number.

If the problem persists, increase the tension in the bobbin by turning the screw clockwise with a screwdriver.

Be sure not to turn the screw more than one full turn. In addition, be sure to return the screw to its original position before the next time that the machine is used.

Note

The bobbin thread tension has been adjusted at the factory for general use. For most sewing applications, no adjustment is needed.

24

SEWING BASICS ———————————————————————————————————————————————————

USEFUL SEWING TIPS

Various ways to achieve better results for your sewing projects are described below. Refer to these tips when sewing your project.

Trial sewing

A trial piece of fabric should be sewn since, depending on the type of fabric and stitching being sewn, the desired results may not be achieved.

For the trial sewing, use a piece of fabric and thread that are the same as those used for your project, and check the thread tension and stitch length and width. Since the results differ depending on the type of stitching and the number of layers of fabric sewn, perform the trial sewing under the same conditions that will be used with your project.

Changing the sewing direction

aWhen the stitching reaches a corner, stop the sewing machine.

Leave the needle lowered (in the fabric). If the needle was raised, lower the needle by turning the handwheel toward you (counterclockwise).

CAUTION

When using the twin needle, be sure to raise the needle before changing the sewing direction. If the fabric is turned while the needle is lowered, the needle may bend or break.

bRaisefabric.the presser foot lever, and then turn the

Turn the fabric using the needle as a pivot.

cLowersewing.the presser foot lever and continue

Sewing curves

Stop sewing, and then slightly change the sewing direction to sew around the curve.

When sewing along a curve while using a zigzag stitch, select a shorter stitch length in order to obtain a finer stitch.

Sewing thick fabrics

If the fabric does not fit under the presser foot

If the fabric does not fit easily under the presser foot, raise the presser foot lever even higher to bring the presser foot to its highest position.

CAUTION

If fabric more than 6 mm (15/64 inches) thick is sewn or if the fabric is pushed with too much force, the needle may bend or break.

25

Sewing thin fabrics

When sewing thin fabrics, the stitching may become misaligned or the fabric may not feed correctly. If this occurs, place thin paper or stabilizer material under the fabric and sew it together with the fabric. When you have finished sewing, tear off any excess paper.

2

a Stabilizer material or paper

Sewing stretch fabrics

First, baste the pieces of fabric together, and then sew without stretching the fabric.

a Basting

Using a free-arm style

Free-arm sewing is convenient for sewing tubular and hard-to-reach areas.

To change your machine to the free-arm style, lift the bottom of the flat bed attachment toward you, and then pull the flat bed attachment out to remove it.

a Flat bed attachment

26

UTILITY STITCHES ——————————————————————————————————————————————————

3 UTILITY STITCHES

USEFUL STITCHES

Zigzag stitches

You can use the zigzag stitches to join together seams and finish them in one operation. They are also useful for sewing stretch materials.

Stitch width

1-5 (For twin needle sewing,

always use a setting of less than 3.)

 

Stitch length

1-4 (For the Satin Stitch, set at F.)

Needle position

M, L, R (For twin needle sewing,

always set at M.)

 

Presser foot

Zigzag

Needle

Single or Twin

 

 

Simple zigzag stitch

Set the stitch length between 1 and 4 for a simple zigzag stitch.

aLower the needle into the fabric at the beginning of the stitching.

bStart sawing.

For details, refer to “Starting to sew” (page 23).

Memo

When sewing with a zigzag stitch, use straight stitches at the beginning and end of the zigzag stitch for reinforcement.

cWhen sewing is finished, cut the thread.

For details, refer to “Starting to sew” (page 23).

CAUTION

Slowly turn the handwheel toward you (counterclockwise) and check that the needle does not touch the presser foot. If the needle hits the presser foot, the needle may bend or break.

Satin stitch

When the stitch length is set in the F range and the stitch width is set above 1, it produces a Satin Stitch (a close zigzag stitch). The Satin Stitch can be used for making buttonholes and decorative stitches or edging.

Note

It is recommended that a test sample be made on a fabric scrap before sewing on your project.

Basic stitching

Straight stitches are used for sewing plain seams.

Stitch width

0

Stitch length

F-4

Needle position

M, L, R (For twin needle sewing,

always set at M.)

 

Presser foot

Zigzag

Needle

Single or Twin

 

 

aBaste or pin together the fabric pieces.

bLower the needle into the fabric at the beginning of the stitching.

cStart sewing.

For details, refer to “Starting to sew” (page 23).

27

dWhen sewing is finished, cut the thread.

For details, refer to “Starting to sew” (page 23).

Blind hem stitching

You can use the Blind Hem Stitch to finish the edge of a project, like the hem of a pair of trousers, without the stitch showing.

Stitch width

3-5

Stitch length

2-3

Needle position

R

Presser foot

Zigzag

Needle

Single

 

 

aBoth the upper and lower threads should be the same color as the fabric.

bFold back the fabric to the desired location of the hem (a). Then, fold the edge of the fabric (b). Leave a 6 mm (1/4") overlap at the edge.

ab

cSew 5-6 stitches on the fold using the R needle position, a straight stitch (0 width) and stitch length of 3-4. Quickly set the width to 2-3, sew 1 stitch and set the width back to 0. Repeat.

3

dWhen the fabric is unfolded, you will have a

Blind Stitch hem.

28

Loading...
+ 67 hidden pages