Brother CE1100PRW Operation Manual

4 (3)
Brother CE1100PRW Operation Manual

Operation Manual

Sewing Machine

KNOWING YOUR SEWING MACHINE

Product Code: 885-V60/V61/V62/V63/V64/V65

SEWING BASICS

UTILITY STITCHES

APPENDIX

Please visit us at http://solutions.brother.com where you can get product

support and answers to frequently asked questions (FAQs).

——————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

IMPORTANT SAFETY INSTRUCTIONS

Please read these safety instructions before attempting to use the machine.

DANGER - To reduce the risk of electric shock:

1Always unplug the machine from the electrical outlet immediately after using, when cleaning, when making any user servicing adjustments mentioned in this manual, or if you are leaving the machine unattended.

WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons.

2Always unplug the machine from the electrical outlet when making any adjustments mentioned in the instruction manual:

To unplug the machine, switch the machine to the symbol “O” position to turn it off, then grasp the plug and pull it out of the electrical outlet. Do not pull on the cord.

Plug the machine directly into the electrical outlet. Do not use an extension cord.

Always unplug your machine if the power is cut.

3 Never operate this machine if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or water is spilled on the unit. Return the machine to the nearest authorized dealer or service center for examination, repair, electrical or mechanical adjustment.

While the machine is stored or in use if you notice anything unusual, such as an odor, heat, discoloration or deformation, stop using the machine and immediately unplug the power cord.

When transporting the machine, be sure to carry it by its handle. Lifting the machine by any other part may damage the machine or result in the machine falling, which could cause injuries.

When lifting the machine, be careful not to make any sudden or careless movements, otherwise you may injure your back or knees.

1

————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

4 Always keep your work area clear:

Never operate the machine with any air openings blocked. Keep ventilation openings of the machine and foot control free from the build up of lint, dust, and loose cloth.

Do not store objects on the foot controller.

Do not use extension cords. Plug the machine directly into the electrical outlet.

Never drop or insert any object into any opening.

Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

Do not use the machine near a heat source, such as a stove or iron; otherwise, the machine, power cord or garment being sewn may ignite, resulting in fire or an electric shock.

Do not place this machine on an unstable surface, such as an unsteady or slanted table, otherwise the machine may fall, resulting in injuries.

5 Special care is required when sewing:

Always pay close attention to the needle. Do not use bent or damaged needles.

Keep fingers away from all moving parts. Special care is required around the machine needle.

Switch the machine to the symbol “O” position to turn it off when making any adjustments in the needle area.

Do not use a damaged or incorrect needle plate, as it could cause the needle to break.

Do not push or pull the fabric when sewing, and follow careful instruction when freehand stitching so that you do not deflect the needle and cause it to break.

6 This machine is not a toy:

Your close attention is necessary when the machine is used by or near children.

The plastic bag that this machine was supplied in should be kept out of the reach of children or disposed of. Never allow children to play with the bag due to the danger of suffocation.

Do not use outdoors.

7 For a longer service life:

When storing this machine, avoid direct sunlight and high humidity locations. Do not use or store the machine near a space heater, iron, halogen lamp, or other hot objects.

Use only neutral soaps or detergents to clean the case. Benzene, thinner, and scouring powders can damage the case and machine, and should never be used.

Always consult the operation manual when replacing or installing any assemblies, the presser feet, needle, or other parts to assure correct installation.

2

——————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

8 For repair or adjustment:

If the Light unit (light-emitting diode) is damaged, it must be replaced by authorized dealer.

In the event a malfunction occurs or adjustment is required, first follow the troubleshooting table in the back of the operation manual to inspect and adjust the machine yourself. If the problem persists, please consult your local authorized Brother dealer.

Use this machine only for its intended use as described in this manual.

Use accessories recommended by the manufacturer as contained in this manual.

The contents of this manual and specifications of this product are subject to change without notice. For additional product information, visit our web site at www.brother.com

SAVE THESE INSTRUCTIONS

This machine is intended for household use.

FOR USERS IN THE UK, EIRE, MALTA AND

CYPRUS ONLY

IMPORTANT

In the event of replacing the plug fuse, use a fuse approved by ASTA to BS 1362, i.e. carrying the

mark, rating as marked on plug.

Always replace the fuse cover. Never use plugs with the fuse cover omitted.

If the available electrical outlet is not suitable for the plug supplied with this equipment, you should contact your authorized dealer to obtain the correct lead.

FOR USERS IN AC INPUT 220-240V COUNTRIES AND MEXICO

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

3

————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

CONTENTS

 

IMPORTANT SAFETY INSTRUCTIONS ...............................................................................

1

1. KNOWING YOUR SEWING MACHINE ..........................................................

6

ACCESSORIES .....................................................................................................................

6

Included accessories ........................................................................................................................................

6

Optional accessories ........................................................................................................................................

7

Accessory compartment ...................................................................................................................................

7

NAMES OF MACHINE PARTS AND THEIR FUNCTIONS ....................................................

8

The main parts .................................................................................................................................................

8

Needle and presser foot section ......................................................................................................................

9

Operation buttons .............................................................................................................................................

9

Operation panel ..............................................................................................................................................

10

Spool pin ........................................................................................................................................................

10

USING YOUR SEWING MACHINE ...................................................................................

12

Power supply precautions ..............................................................................................................................

12

Power supply ..................................................................................................................................................

12

Foot controller ................................................................................................................................................

13

Sewing speed controller (for models equipped with the start/stop button) .....................................................

13

Changing the needle stop position .................................................................................................................

13

Changing the initial needle position ...............................................................................................................

14

Cancelling the operation beep (for models equipped with the operation beep) .............................................

14

THREADING THE MACHINE ............................................................................................

15

Winding the bobbin ........................................................................................................................................

15

Lower threading .............................................................................................................................................

20

Upper threading .............................................................................................................................................

23

Drawing up the lower thread ..........................................................................................................................

28

REPLACING THE NEEDLE .................................................................................................

29

Needle precautions ........................................................................................................................................

29

Needle types and their uses ...........................................................................................................................

29

Checking the needle ......................................................................................................................................

30

Replacing the needle .....................................................................................................................................

30

Sewing with the twin needle ...........................................................................................................................

32

REPLACING THE PRESSER FOOT ......................................................................................

34

Replacing the presser foot .............................................................................................................................

34

Removing the presser foot holder ..................................................................................................................

35

2. SEWING BASICS ...........................................................................................

36

SEWING ............................................................................................................................

36

General sewing procedure .............................................................................................................................

36

Selecting a stitch ............................................................................................................................................

37

Adjusting the stitch length and width ..............................................................................................................

38

Starting to sew ...............................................................................................................................................

39

Thread tension ...............................................................................................................................................

41

USEFUL SEWING TIPS ......................................................................................................

42

Trial sewing ....................................................................................................................................................

42

Changing the sewing direction .......................................................................................................................

42

Sewing curves ................................................................................................................................................

42

Sewing thick fabrics .......................................................................................................................................

42

Sewing hook-and-loop fastener .....................................................................................................................

43

Sewing thin fabrics .........................................................................................................................................

44

Sewing stretch fabrics ....................................................................................................................................

44

Stitching cylindrical pieces .............................................................................................................................

44

4

——————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

3. UTILITY STITCHES ........................................................................................

45

OVERCASTING STITCHES ................................................................................................

45

Using zigzag foot ............................................................................................................................................

45

Using overcasting foot ....................................................................................................................................

46

BASIC STITCHING ............................................................................................................

47

Basic stitching ................................................................................................................................................

47

BLIND HEM STITCHING ..................................................................................................

48

BUTTONHOLE SEWING ...................................................................................................

51

Button sewing .................................................................................................................................................

55

ZIPPER INSERTION ...........................................................................................................

57

SEWING STRETCH FABRICS AND ELASTIC TAPE ............................................................

59

Stretch stitching ..............................................................................................................................................

59

Elastic attaching .............................................................................................................................................

59

APPLIQUÉ, PATCHWORK AND QUILT STITCHING ........................................................

61

Appliqués .......................................................................................................................................................

62

Patchwork (crazy quilt) stitching .....................................................................................................................

62

Piecing ...........................................................................................................................................................

62

Quilting ...........................................................................................................................................................

63

Free-motion quilting .......................................................................................................................................

64

REINFORCEMENT STITCHING .........................................................................................

66

Triple stretch stitching ....................................................................................................................................

66

Bar tack stitching ............................................................................................................................................

66

DECORATIVE STITCHING ................................................................................................

68

Fagoting .........................................................................................................................................................

69

Scallop stitching .............................................................................................................................................

70

Smocking .......................................................................................................................................................

70

Shell tuck stitching .........................................................................................................................................

71

Joining ............................................................................................................................................................

71

Heirloom stitching ...........................................................................................................................................

72

4. APPENDIX .....................................................................................................

73

STITCH SETTINGS .............................................................................................................

73

Utility stitches .................................................................................................................................................

73

MAINTENANCE ................................................................................................................

80

Restrictions on oiling ......................................................................................................................................

80

Precautions on storing the machine ...............................................................................................................

80

Cleaning the machine surface ........................................................................................................................

80

Cleaning the race ...........................................................................................................................................

80

TROUBLESHOOTING .......................................................................................................

83

Frequent troubleshooting topics .....................................................................................................................

83

Upper thread tightened up .............................................................................................................................

83

Tangled thread on wrong side of fabric ..........................................................................................................

84

Incorrect thread tension .................................................................................................................................

87

Fabric is caught in the machine and cannot be removed ...............................................................................

88

List of symptoms ............................................................................................................................................

92

ERROR MESSAGES ............................................................................................................

97

Operation beep (for models equipped with the operation beep) ....................................................................

97

INDEX ...............................................................................................................................

98

5

KNOWING YOUR SEWING MACHINE —————————————————————————————————————————————————————————————————————————————————

1 KNOWING YOUR SEWING MACHINE

ACCESSORIES

Included accessories

After opening the box, check that the following accessories are included. If any item is missing or damaged, contact your dealer.

Note

Foot controller: Model T

This foot controller can be used on the machine with product code 885-V60/V61/V62/V63/V64/V65. The product code is mentioned on the machine rating plate.

The screw of the presser foot holder is available through your authorized dealer. (Part code: 132730-122)

The included accessories vary depending on the machine model.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

 

11.

12.

13.

14.

15.

75/11 1 needle 90/14 1 needle 100/16 1 needle

90/14 1 needle

16. 17. 18. 19.

No.

Part Name

Part Code

Americas

Others

 

 

1

Zigzag foot “J” (on machine)

XC3021-031

2

Buttonhole foot “A”

XC2691-033

3

Overcasting foot “G”

XE6305-101

4

Monogramming foot “N”

XD0810-031

5

Zipper foot “I”

X59370-021

6

Blind stitch foot “R”

XC4051-031

7

Button fitting foot “M”

XE2137-001

8

Seam ripper

XZ5082-001

9

Bobbin (4)

SA156

SFB:

(One is on machine.)

XA5539-151

10

Needle set

XC8834-021

No.

Part Name

Part Code

Americas

Others

 

 

11

Twin needle

131096-121

12

Ball point needle

XD0360-021

 

(gold colored)

 

 

13

Cleaning brush

X59476-021

14

Disc-shaped screwdriver

XC1074-051

15

Spool cap (large)

130012-024

16

Spool cap (medium)

XE1372-001

 

(on machine)

 

 

17

Spool cap (small)

130013-124

18

Extra spool pin

XE2241-001

19

Foot controller

XD0501-021 (EU area)

XC8816-021 (Other areas)

 

 

Memo

● About zigzag foot “J”;

Press the black button on the left side of the foot when it is difficult for thick seams to be fed, for example, at the beginning of sewing thick fabrics. (page 43)

aBlack button

6

——————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

Optional accessories

The following are available as optional accessories to be purchased separately. Depending on the model you purchased, the following accessory may be included with your machine.

 

 

 

 

 

 

 

 

 

 

 

 

1

1.

 

 

2.

 

 

3.

4.

5.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

No.

Part Name

Part Code

Americas

Others

 

 

1

Walking Foot

SA140

F033N:

XC2214-002

 

 

 

2

Quilting Foot

SA129

F005N:

XC1948-002

 

 

 

3

1/4-Inch Quilting Foot

SA125

F001N:

XC1944-052

 

 

 

No.

Part Name

Part Code

Americas

Others

 

 

4

Quilting guide

SA132

F016N:

XC2215-002

 

 

 

5

Eyelet punch

XZ5051-001

Accessory compartment

The accessories are stored in a compartment inside the flat bed attachment. Slide the flat bed attachment to the left to open it.

Note

● Put the accessories in the bag, and then store the bag inside the compartment. If the accessories are not in a bag, they may fall out, and be lost or damaged.

aFlat bed attachment

bStorage compartment

7

KNOWING YOUR SEWING MACHINE —————————————————————————————————————————————————————————————————————————————————

NAMES OF MACHINE PARTS AND THEIR FUNCTIONS

The illustrations in this operation manual may differ from the actual machine.

The main parts

aBobbin winder (page 15)

This winds the thread onto the bobbin for use as the lower thread.

bUpper tension-control dial (page 41)

This controls the tension of the upper thread.

cBobbin-winding thread guide and pretension disc (page 15)

Pass the thread under this thread guide and around the pretension disc when winding the bobbin thread.

dThread take-up lever (page 25)

eThread cutter (page 40)

Pass the threads through the thread cutter to cut them.

fFlat bed attachment with accessory compartment (page 7 and 44)

gOperation buttons (page 9)

The operation buttons differ depending on the sewing machine model.

hOperation panel (page 10)

This is used to select the stitch and specify the various settings. Design and position of the operation panel differs depending on the sewing machine model.

iSpool pin (page 10, 15 and 23)

This holds the spool of thread.

jHandwheel

This is used to manually raise and lower the needle.

kAir vent

This vent allows the air surrounding the motor to circulate. Do not cover the air vent while the sewing machine is being used.

lMain power and sewing light switch (page 12)

You can turn the main power and sewing light switch on and off.

mJack/socket connector (page 12)

Insert the plug on the power supply cord into the jack/ socket connector.

nFoot controller (page 13)

You can use this to control the sewing speed, and to start and stop sewing.

oFoot controller jack/socket (page 13)

Plug in the foot controller plug.

pFeed dog position lever (page 55 and 65)

Use the feed dog position lever to lower the feed dogs.

qPresser foot lever (page 23)

This is used to raise and lower the presser foot.

rThread guide (page 16 and 25)

This is used when winding the thread onto the bobbin and then threading the machine.

sThread guide cover (page 17 and 23)

Pass the thread under this thread guide when winding the bobbin thread and threading the machine.

tHandle

Carry the sewing machine by its handle when transporting the machine.

8

——————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

Needle and presser foot section

aNeedle threader (for models equipped with the needle threader) (page 26)

bButtonhole lever

Lower the buttonhole lever when sewing buttonholes and bar tacks.

cPresser foot holder

The presser foot is installed onto the presser foot holder.

dPresser foot holder screw

Use the presser foot holder screw to hold the presser foot holder in place.

ePresser foot

The presser foot applies pressure consistently on the

fabric as the sewing takes place. Attach the appropriate

1

presser foot for the selected stitching.

fNeedle plate cover release

Use when removing the needle plate cover.

gNeedle plate cover

Remove the needle plate cover to clean the race.

hFeed dogs

The feed dogs feed the fabric in the sewing direction.

iQuick-set bobbin (for models equipped with the quickset bobbin)

You can start sewing without pulling up the bobbin thread.

jBobbin cover

Open the bobbin cover to set the bobbin.

kNeedle plate

The needle plate is marked with guides for sewing straight seams.

lNeedle bar thread guide

Pass the upper thread through the needle bar thread guide.

mPresser foot lever

Raise and lower the presser foot lever to raise and lower the presser foot.

nNeedle clamp screw

Use the needle clamp screw to hold the needle in place.

Operation buttons

The operation buttons help you to easily perform various basic sewing machine operations. The operation buttons differ depending on the sewing machine model.

aReverse/reinforcement stitch button

Press the reverse/reinforcement stitch button to sew reverse stitches. Reverse stitches are sewn by keeping the button pressed down to sew in the opposite direction. For details, refer to “Sewing reinforcement stitches” (page 40).

Buttons provided on some models

b Start/stop button (for models equipped with the start/stop button)

Press the start/stop button to start or stop sewing. The machine sews at a slow speed at the beginning of sewing while the button is depressed. When sewing is stopped, the needle is lowered in the fabric. For details, refer to “Starting to sew” (page 39).

c Needle position button (for models equipped with the needle position button)

Press the needle position button to raise or lower the needle. Be sure to raise the needle before threading the needle. Use this button to change the sewing direction or for detailed sewing in small areas. Pressing the button twice sews one stitch.

dSewing speed controller (for models equipped with the sewing speed controller)

Slide the sewing speed controller to adjust the sewing speed.

9

KNOWING YOUR SEWING MACHINE —————————————————————————————————————————————————————————————————————————————————

Operation panel

The operation panel, located on the front of the sewing machine, allows you to select a stitch and specify how the stitch will be sewn.

The operation panel differs depending on the sewing machine model.

aLCD (liquid crystal display)

The number of the selected stitch (1), the presser foot type to be used (2), the stitch length (mm) (3), and the stitch width (mm) (4) are displayed here.

The display location (2) of the presser foot type differs depending on the model.

This manual shows, as an example, the LCD (illustration above) of models where the presser foot type appears above the number of the selected stitch.

bStitch selection keys

Press the stitch selection keys, and then select the number for the stitch that you wish to use. For details, refer to “Selecting a stitch” (page 37).

cStitch length adjustment key

Press this key to adjust the stitch length. (Press the “–” side to reduce the stitch length; press the “+” side to increase the stitch length.)

dStitch width adjustment key

Press this key to adjust the stitch width. (Press the “–” side to reduce the stitch width; press the “+” side to increase the stitch width.)

Spool pin

As shown, press down on the spool pin lever with your finger to raise the spool pin.

CAUTION

Do not grab the bar to raise the spool pin, otherwise, the spool pin may bend or break.

Storing the spool cap

The enclosed spool cap (large, medium, small) can be stored by attaching it to the spool pin as shown in the illustration. When attaching the spool cap, position it with the rounded side toward the spool pin.

10

——————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

Storing the spool pin

When placing the cover on the sewing machine before storing or if the spool pin will not be used, return the spool pin to its storage position. Remove the spool from the spool pin, and then fold up the spool pin, as shown in the illustration, until it snaps into place to secure it.

Installing the spool pin

aIf the spool pin has been removed from the machine, insert the tab on the spool pin into the hole on the back of the machine, as

shown.

1

aHole

bTab

bPushplace.the spool pin down until it locks into

11

KNOWING YOUR SEWING MACHINE —————————————————————————————————————————————————————————————————————————————————

USING YOUR SEWING MACHINE

Power supply precautions

Be sure to observe the following precautions concerning the power supply.

WARNING

Use only regular household electricity for the power source. Using other power sources may result in fire, electric shock, or damage to the machine.

Make sure that the plugs on the power cord are firmly inserted into the electrical outlet and the power supply jack on the machine.

Do not insert the plug on the power cord into an electrical outlet that is in poor condition.

Turn off the main power and remove the plug in the following circumstances:

When you are away from the machine

After using the machine

When the power fails during use

When the machine does not operate correctly due to a bad connection or a disconnection

During electrical storms

CAUTION

Use only the power cord included with this machine.

Do not use extension cords or multi-plug adapters with many other appliances plugged in to them. Fire or electric shock may result.

Do not touch the plug with wet hands. Electric shock may result.

When unplugging the machine, always turn off the main power first. Always grasp the plug to remove it from the outlet. Pulling on the cord may damage the cord, or lead to fire or electric shock.

Do not allow the power cord to be cut, damaged, modified, forcefully bent, pulled, twisted, or bundled. Do not place heavy objects on the cord. Do not subject the cord to heat. These things may damage the cord and cause fire or electric shock. If the cord or plug is damaged, take the machine to your authorized dealer for repairs before continuing use.

Unplug the power cord if the machine is not to be used for a long period of time. Otherwise a fire may result.

Power supply

aInsert the plug into a wall outlet.

1 2

aMain power switch

bJack/socket connector

bSet the main power switch to “I”.

XThe sewing lamp comes on when the machine is turned on.

cTo turn off the machine, set the main power switch to “{”.

XThe sewing lamp goes off when the machine is turned off.

Note

If a power outage occurs while the sewing machine is being operated, turn off the sewing machine and unplug the power supply cord. When restarting the sewing machine, follow the necessary procedure to correctly operate the machine.

(For U.S.A. only)

This appliance has a polarized plug (one blade wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug.

If it still does not fit, contact a qualified electrician to install the proper outlet. Do not modify the plug in any way.

12

——————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

Foot controller

Insert the foot controller plug into its jack/socket on the rear side of the sewing machine.

a Foot controller jack/socket

CAUTION

When connecting the foot controller, be sure to turn off the sewing machine in order to prevent the machine from accidentally being started.

When you press the foot controller down lightly, the machine will run at a low speed. When you press harder, the machine’s speed will increase. When you take your foot off the foot controller, the machine will stop.

Slower

Faster

You should make sure that nothing is placed on the foot controller when the machine is not in use.

CAUTION

Do not allow pieces of cloth and dust to build up on the foot controller. Doing so could cause a fire or an electric shock.

Note

When the foot controller is plugged in, the start/stop button cannot be used to start sewing (only for models equipped with the start/stop button).

Sewing speed controller (for models equipped with the start/stop button)

Slide the sewing speed controller to the left or

1

aright to select the desired sewing speed.

 

Slide the sewing speed controller to the left to sew at a slower speed, or slide the speed controller to the right to sew at a faster speed.

a Sewing speed controller

The speed set using the sewing speed controller is the foot controller’s maximum sewing speed.

Changing the needle stop position

Normally, the sewing machine is set to leave the needle in the fabric when sewing is stopped. Instead, the machine can be set to leave the needle raised when sewing is stopped.

aTurn off the sewing machine.

bHold down the “–” side of (stitch selection

key) on the left and turn on the sewing machine.

After turning on the sewing machine, release the “–” side of (stitch selection key).

XThe needle stop position changes to the raised position.

Memo

Perform the same operation to change the needle stop position to the lowered position.

13

KNOWING YOUR SEWING MACHINE —————————————————————————————————————————————————————————————————————————————————

Changing the initial needle position

Normally, the straight stitch (left needle position) is automatically selected when the sewing machine is turned on. The machine can be set so that the straight stitch (center needle position) is automatically selected when it is turned on.

aTurn off the sewing machine.

bHold down the “+” side of (stitch selection key) on the left and turn on the sewing machine.

After turning on the sewing machine, release the “+” side of (stitch selection key).

XThe initial needle position changes to the center needle position.

Memo

The specified initial needle position is maintained even after the machine is turned off.

Perform the same operation to change the initial needle position to the left needle position.

Cancelling the operation beep (for models equipped with the operation beep)

When the sewing machine is purchased, it is set to beep each time a key is pressed. This setting can be changed so that the machine does not beep.

aTurn off the sewing machine.

bHold down the “–” side of (stitch width adjustment key) and turn on the sewing machine.

After turning on the sewing machine, release the “-” side of (stitch width adjustment key).

XThe machine is now set so that it will not beep.

Memo

Perform the same operation to change the setting so that machine beeps.

14

——————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

THREADING THE MACHINE

Winding the bobbin

1

 

This section describes how to wind the thread onto the bobbin.

• For details on the fast bobbin winding, see page 18.

a Bobbin-winding thread guide

b Bobbin winder shaft c Bobbin

CAUTION

Only use bobbins (part code: SA156, SFB: XA5539-151) that have been designed for this sewing machine. Using other bobbins may cause damage to the machine.

We designed the bobbin that comes with this machine. If you use bobbins from other models, the machine will not work properly. Only use the bobbin that comes with this machine or bobbins of the same type (part code: SA156, SFB: XA5539-151).

Actual size

11.5 mm (7/16 inch)

This model

Other models

 

 

aAs shown, press down on the spool pin lever with your finger.

X The spool pin swings up.

CAUTION

Do not grab the bar to raise the spool pin, otherwise, the spool pin may bend or break.

bRemove the spool cap.

aSpool pin

bSpool cap

CAUTION

Be sure to raise the spool pin when winding the bobbin. The thread may become tangled if the bobbin winder is used without raising the spool pin.

15

KNOWING YOUR SEWING MACHINE —————————————————————————————————————————————————————————————————————————————————

cFully insert the spool of thread for the bobbin onto the spool pin.

Slide the spool onto the pin so that the spool is horizontal and the thread unwinds to the front at the bottom.

dSlide the spool cap onto the spool pin.

With the slightly rounded side of the spool cap positioned toward the left, slide the spool cap onto the spool pin as far as possible to the right so that the spool is moved to the right end of the spool pin.

CAUTION

If the spool or the spool cap is not positioned correctly, the thread may become tangled around the spool pin or the machine may be damaged.

Three spool cap sizes are available, allowing you to choose a spool cap that best fits the size of spool being used. If the spool cap is too small for the spool being used, the thread may catch on the slit in the spool or the machine may be damaged.

Memo

When sewing with fine, cross-wound thread, use the small spool cap, and leave a small space between the cap and the spool.

c b

a

aSpool cap (small)

bSpool (cross-wound thread)

cSpace

eWhile holding the spool with your right hand, and then pass the thread under the thread guide.

a Thread guide

fPass the thread under the thread guide cover from the back to the front.

Hold the thread with your right hand so that there is no slack in the thread that is pulled out, and then pass the thread under the thread guide cover with your left hand.

a Thread guide cover

16

——————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

gPull the thread to the right, pass it under the hook of the bobbin-winding thread guide, and then wind the thread counterclockwise between the discs, pulling it in as far as possible.

a Bobbin-winding thread guide

Make sure that the thread passes under the pretension disk.

bHook

cPretension disk

dPull it in as far as possible.

Note

Make sure that the thread is pulled as far as possible into the pretension disk, otherwise the bobbin may not be wound cleanly.

hPut the bobbin onto the bobbin winder shaft and slide the bobbin winder shaft to the right. Turn the bobbin clockwise, by hand, until the spring on the shaft slides into the notch in the bobbin.

Make sure to pull out 7 to 10 cm (2-3/4 to 3-15/16 inches) of thread from the hole on the bobbin.

aSpring on the shaft

bNotch

c7-10 cm (2-3/4 – 3-15/16 inches)

CAUTION

Pull the thread taut and hold the end of the thread straight up. If the thread is too short,

not pulled taut or held at an angle, injuries 1 may occur when the thread is wound around

the bobbin.

iTurn on the sewing machine.

jWhile holding the end of the thread, gently press the foot controller or press (start/ stop button) (for models equipped with the start/stop button) to wind the thread around the bobbin a few times. Then stop the machine.

Note

If the sewing machine is to be operated using the foot controller, connect the foot controller before turning on the machine.

When the foot controller is plugged in, the start/stop button cannot be used to start sewing (only for models equipped with the start/stop button).

kTrim the excess thread above the bobbin.

Leave 1 cm (3/8 inch) of thread from the hole on the bobbin.

1

a 1 cm (3/8 inch)

CAUTION

Make sure you follow the instructions carefully. If you do not cut the thread completely, and the bobbin is wound, when the thread runs low it may tangle around the bobbin and cause the needle to break.

17

KNOWING YOUR SEWING MACHINE —————————————————————————————————————————————————————————————————————————————————

lSlide the sewing speed controller to the right (to set the speed to fast). (For models equipped with the sewing speed controller.)

a Sewing speed controller

mPress the foot controller or press (start/ stop button) (for models equipped with the start/stop button) to start.

nWhen the bobbin seems full and begins spinning slowly, take your foot off the foot controller or press (start/stop button) (for models equipped with the start/stop button).

oCut the thread, slide the bobbin winder shaft to the left and remove the bobbin.

pSlide the sewing speed controller back to its original position (for models equipped with the sewing speed controller).

Memo

When the sewing machine is started or the handwheel is turned after winding the thread around the bobbin, the machine will make a clicking sound; this is not a malfunction.

The needle bar does not move when you slide the bobbin winding shaft to the right.

CAUTION

Not winding the bobbin properly may cause the thread tension to loosen, and may break the needle.

1 2

aWound evenly

bWound poorly

For models equipped with the fast bobbin winding system

aPlace the bobbin on the bobbin winder shaft so that the spring on the shaft fits into the notch in the bobbin.

aNotch

bBobbin winder shaft spring

bSlide the bobbin winder shaft to the right.

cFollow steps a through g of the procedure in “Winding the bobbin” to pass the thread around the pre-tension disk (page 15).

dWhile holding the thread that wraps around the pre-tension disk with your left hand, use your right hand to wind the free end of the thread clockwise around the bobbin five or six times.

18

——————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

ePull the thread to the right and pass it through the slit in the bobbin winder seat.

a Slit in bobbin winder seat (with built-in cutter)

X The thread is cut to a suitable length.

CAUTION

Be sure to cut the thread as described. If the bobbin is wound without cutting the thread using the cutter built into the slit in the bobbin winder seat, the thread may become tangled in the bobbin or the needle may bend or break when the bobbin thread starts to run out.

fSlide the sewing speed controller to the right (to set the speed to fast) (for models equipped with the sewing speed controller).

a Sewing speed controller

gTurn on the sewing machine.

hPress the foot controller or press (start/ stop button) (for models equipped with the start/stop button) to start.

Note

If the sewing machine is to be operated using the foot controller, connect the foot controller before turning on the machine.

When the foot controller is plugged in, the start/stop button cannot be used to start sewing (only for models equipped with the start/stop button).

iWhen the bobbin begins spinning slowly, take your foot off the foot controller or press (start/stop button) (for models equipped with the start/stop button).

jCut the thread, slide the bobbin winder shaft to the left, and then remove the bobbin from the shaft.

1

kSlide the sewing speed controller back to its original position (for models equipped with the sewing speed controller).

CAUTION

Not winding the bobbin properly may cause the thread tension to loosen, and may break the needle.

1 2

aWound evenly

bWound poorly

Memo

When the sewing machine is started or the handwheel is turned after winding the thread around the bobbin, the machine will make a clicking sound; this is not a malfunction.

The needle bar does not move when you slide the bobbin winding shaft to the right.

19

KNOWING YOUR SEWING MACHINE —————————————————————————————————————————————————————————————————————————————————

Lower threading

Install the bobbin wound with thread.

• For more details on quick-set bobbin, see page 21.

CAUTION

Winding the bobbin improperly may cause the thread tension to loosen, breaking the needle and resulting in injury.

12

aWound evenly

bWound poorly

The bobbin was designed specifically for this sewing machine. If bobbins from other models are used, the machine will not operate correctly. Use only the enclosed bobbin or bobbins of the same type (part code: SA156, SFB: XA5539-151).

Actual size

11.5 mm (7/16 inch)

This model

Other models

CAUTION

Make sure you turn the power off while threading the machine. If you accidentally step on the foot controller and the machine starts to sew, you could be injured.

Memo

The direction for feeding the bobbin thread is indicated by marks on the needle plate cover. Be sure to thread the machine as indicated.

aRaise the needle to its highest position by turning the handwheel toward you (counterclockwise) or

press (needle position button) (for models equipped with the needle position button), and raise the presser foot lever.

bTurn off the sewing machine.

cSlide the button and open the cover.

1 2

aCover

bSlide button

dPut the bobbin in so the thread comes out in the direction shown by the arrow.

CAUTION

Make sure you set the bobbin so the thread unrolls in the right direction. If the thread unrolls in the wrong direction, it may cause the thread tension to be incorrect or break the needle.

20

——————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

eHold the end of the thread, push the bobbin down with your finger, and then pass the thread through the slit, as shown.

If the thread is not correctly inserted through the tension-adjusting spring of the bobbin case, it may cause incorrect thread tension (page 41).

1

a Tension-adjusting spring

fReplace the bobbin cover. Put the left tab in place (see arrow a), and then press lightly on the right side (see arrow b) until the cover clicks into place.

Replace the cover so that the end of the thread comes out from the left side of the cover (as shown by the line in the diagram).

For models equipped with the quick-set bobbin

Memo

The direction for feeding the bobbin thread is indicated by marks on the needle plate cover. Be sure to thread the machine as indicated.

aRaise the needle to its highest position by turning the handwheel toward you (counterclockwise) or

press (needle position button) (for models equipped with the needle position button), and raise the presser foot lever.

1

bTurn off the sewing machine.

cSlide the button and open the cover.

1 2

aCover

bSlide button

dInsert the bobbin with your right hand so that the end of the thread is on the left, and then, after pulling the thread firmly around the tab with your left hand as shown, lightly pull the thread to guide it through the slit.

a Tab

CAUTION

Make sure you set the bobbin so the thread unrolls in the right direction. If the thread unrolls in the wrong direction, it may cause the thread tension to be incorrect or break the needle.

21

KNOWING YOUR SEWING MACHINE —————————————————————————————————————————————————————————————————————————————————

eWhile lightly holding down the bobbin with your right hand as shown, guide the thread through the slit (a and b).

• At this time, check that the bobbin easily

rotates counterclockwise.

Then, pull the thread toward you to cut it with the cutter (c).

aSlit

bCutter (Cut the thread with the cutter.)

Note

If the thread is not correctly inserted through the tension-adjusting spring of the bobbin case, it may cause incorrect thread tension (page 41).

fReplace the bobbin cover. Put the left tab in place (see arrow a), and then press lightly on the right side (see arrow b) until the cover clicks into place.

Memo

You can begin sewing immediately without drawing up the bobbin thread. If you want to draw up the bobbin thread before you start to sew, follow to the procedure in “Drawing up the lower thread” (page 28).

1

a Tension-adjusting spring

22

——————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

Upper threading

Set the upper thread and thread the needle.

• For details on the needle threader, see page 26.

1

aSpool pin

bMark on the handwheel

CAUTION

When threading the upper thread, carefully follow the instructions. If the upper threading is not correct, the thread may become tangled or the needle may bend or break.

Never use a thread weight of 20 or lower.

Use the needle and the thread in the correct combination. For details on the correct combination of needles and threads, refer to “Needle types and their uses” (page 29).

aTurn on the sewing machine.

bRaiselever.the presser foot using the presser foot

a Presser foot lever

CAUTION

If the presser foot is not raised, the sewing machine cannot be threaded correctly.

cRaise the needle by turning the handwheel toward you (counterclockwise) so that the mark on the wheel points up, or press (needle position button) (for models equipped with the needle position button) once or twice to raise the needle.

or

a Mark

b Needle position button

If the needle is not correctly raised, the sewing machine can not be threaded. Be sure to turn the handwheel so that the mark on the wheel points up before threading the sewing machine.

23

KNOWING YOUR SEWING MACHINE —————————————————————————————————————————————————————————————————————————————————

dAs shown, press down on the spool pin lever with your finger.

X The spool pin swings up.

CAUTION

Do not grab the bar to raise the spool pin, otherwise, the spool pin may bend or break.

eRemove the spool cap.

aSpool pin

bSpool cap

CAUTION

Be sure to raise the spool pin before use. If the spool of thread is in the wrong place, or is set incorrectly, the thread may tangle on the spool pin and cause the needle to break.

fFully insert the spool for the upper thread onto the spool pin.

Slide the spool onto the pin so that the spool is horizontal and the thread unwinds to the front at the bottom.

gSlide the spool cap onto the spool pin.

With the slightly rounded side of the spool cap positioned toward the left, slide the spool cap onto the spool pin as far as possible to the right so that the spool is moved to the right end of the spool pin.

CAUTION

If the spool or the spool cap is not positioned correctly, the thread may become tangled around the spool pin or the needle may break.

Three spool cap sizes are available, allowing you to choose a spool cap that best fits the size of spool being used. If the spool cap is too small for the spool being used, the thread may catch on the slit in the spool or the needle may break.

24

——————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

Memo

When sewing with fine, cross-wound thread, use the small spool cap, and leave a small space between the cap and the spool.

c b

a

aSpool cap (small)

bSpool (cross-wound thread)

cSpace

hWhile holding the spool with your right hand, and then pass the thread under the thread guide.

a Thread guide

iPass the thread under the thread guide cover from the back to the front.

Hold the thread with your right hand so that there is no slack in the thread that is pulled out, and then pass the thread under the thread guide cover with your left hand.

jFeed the upper thread as shown in the illustration below.

1

kMake sure you guide the thread through the thread take-up lever from right to left as shown in the illustration below.

a Thread take-up lever

Memo

If the needle is not raised, the thread takeup lever cannot be threaded. Be sure to press the needle position button to raise the needle before threading the thread take-up lever.

a Thread guide cover

25

KNOWING YOUR SEWING MACHINE —————————————————————————————————————————————————————————————————————————————————

lPut the thread behind the needle bar thread guide above the needle.

The thread can easily be passed behind the needle bar thread guide by holding the thread in your left hand, then feeding the thread with your right hand.

1

a Needle bar thread guide

mTurn off the sewing machine.

CAUTION

Make sure you turn the power off while threading the machine without using the needle threader (for models equipped with the needle threader). If you accidentally step on the foot controller and the machine starts to sew, you could be injured.

nThread the needle from front to back and pull out about 5 cm (2 inches) of thread.

Note

If the thread take-up lever is lowered, the upper thread cannot be wrapped around the thread take-up lever. Make sure you raise the presser foot lever and the thread take-up lever before you feed the upper thread.

If you incorrectly feed the thread you may cause sewing problems.

Using the needle threader (for models equipped with the needle threader)

CAUTION

The needle threader can be used with a 75/11 through 100/16 home sewing machine needle. However, the needle threader cannot be used with a 65/9 home sewing machine needle. When using special thread such as transparent nylon thread or metallic thread, the needle threader cannot be used.

Thread with a thickness of 130/120 or thicker cannot be used with the needle threader.

The needle threader cannot be used with the wing needle or the twin needle.

If the needle threader cannot be used, refer to “Upper threading” (page 23).

aFollow steps a through m of the procedure in “Upper threading” to thread the machine to the needle bar thread guide.

bLower the presser foot lever.

cWhile lowering the needle threader lever, hook the thread onto the guide.

a Needle holder

b Needle threader lever

c Guide

a 5 cm (2 inches)

26

——————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

dFully lower the needle threader lever.

XThe end of the needle threader rotates toward you and the hook passes through the eye of the needle.

eCatch the thread on the hook as shown below.

aHook

bThread

fWhile lightly holding the thread, release the needle threader lever. The hook will pull the thread through the needle.

gPull the loop of the thread passed through the eye of the needle toward the rear of the machine.

1

a Loop of thread

CAUTION

Be careful not to pull on the thread with force or it may bend the needle.

If the thread does not pass through the eye of the needle, start from step c again.

hRaise the presser foot lever.

a Presser foot lever

iPass the end of the thread through the presser foot, and then pull out about 5 cm (2 inches) of thread toward the rear of the machine.

a 5 cm (2 inches)

Note

If you incorrectly feed the thread you may cause sewing problems.

27

KNOWING YOUR SEWING MACHINE —————————————————————————————————————————————————————————————————————————————————

Drawing up the lower thread

aLightly hold the end of the upper thread.

a Upper thread

bWhile holding the end of the upper thread, raise the needle either by turning the handwheel toward you (counterclockwise) so that the mark on the wheel points up or by pressing (needle position button) (for models equipped with the needle position button) once or twice.

or

a Mark

b Needle position button

cPullthread.on the upper thread to draw up the lower

dPull out about 10 cm (4 inches) of both threads and pull them toward the back of the machine under the presser foot.

aUpper thread

bLower thread

For models equipped with the quick-set bobbin

You can begin sewing immediately without drawing up the bobbin thread. When sewing gathers or darts, you can draw up the lower thread by hand so that some thread will be left over. Before you draw up the lower thread, put the bobbin back in.

aPass the thread along the slit in the direction of the arrow, and leave it there without cutting it.

• The bobbin cover should still be removed.

bDraw up the lower thread as described in steps 1 to 4.

cReplace the bobbin cover.

aUpper thread

bLower thread

28

Loading...
+ 74 hidden pages