Broan BKSH130BL ADA HIGH VOLTAGE WIRING INSTRUCTIONS

ADA HIGH VOLTAGE WIRING INSTRUCTIONS FOR SINGLE BLOWER RANGE HOODS WITH

ELONGATED ROCKER SWITCH CONTROL

! WARNING

For residential (domestic) installation only. Before proceeding, switch power off at service panel and lock service disconnecting means to prevent power from being switched on accidentally. Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction codes and standards. Also, it is recommended to wear safety glasses and gloves.

ACCESS TO RANGE HOOD CONTROL PANEL CONNECTIONS

NOTE: The illustrations in this procedure are generic; some hood details may slightly differ from the hood you have on hand but the procedure itself applies to all single blower range hoods listed in this document (see page 3).

Remove filters from the hood and set them aside. NOTE: Some models have only one filter.

Remove the wiring cover (shaded part on illustration below) retaining screw. Slide out the wiring cover from the hood and set it aside with its screw.

Using a 11/32'' socket, remove the 6 nuts retaining the blower chamber to the hood assembly (2 nuts on inner back and 2 other nuts per sides), then use a Phillips no. 2 screwdriver to remove both front corner screws. See picture below for nuts and screws locations. Pull out the blower chamber from the hood assembly and set it aside with its retaining screws and nuts.

Wiring cover

screw

Unplug the blower connector from the main harness.

Nuts

Nuts

Screw

HD0672

Remove and set aside the 4 front screws retaining the bent plate to the hood.

Screw locations

HD0673

Fold back the bent plate to access to control panel connections.

HE0253

HD0900

1

99045859A

CAUTION

Use standard switches that are rated 120 VCA, 15 A. Only use wires suitable for at least 90oC (194oF). Ensure the wires are reliably routed away from the halogen lights.

According to your needs, there are 2 ways to wire a 2-rocker switch control to these range hoods: 120 VAC power cable entering the range hood or 120 VAC power cable entering the switch box.

120 VAC POWER CABLE ENTERING THE HOOD

	2-ROCKER
	SWITCH
Install a 2-rocker switch at a convenient place for the	RED
	(motor)	GROUND
user. Use a 14/3 cable to wire it to the range hood
	WHITE
(see diagram at right).	BLACK
NOTE: Code requires both ends of WHITE wire
	(lights)
insulation to be colored; use a permanent
marker.

Motor switch

Light switch

	14/3 CABLE
NOTE: Allow enough length of 14/3 cable to perform the RED wire	TO HOOD
connection in the hood nose.

Insert the 14/3 cable along with the 14/2 house wiring cable in the	3	5
hood through an UL approved wire clamp, suitable for 2 cables.		TO CONTROL PANEL
Add a GROUND wire and connect one end to the GREEN ground		2
screw. Use an appropriate wire nut to connect the other end of the
added GROUND wire with the ground wire coming from the 14/3	4
cable and the ground wire coming from 14/2 house wiring cable.		MOTOR
Connect BLACK wire from house wiring to WHITE wire from		GROUND
		WIRE

14/3 cable using an appropriate wire nut.

	Connect BLACK wire from 14/3 cable to BLACK wire from range		BLACK
			WHITE
	hood wiring using an appropriate wire nut.
		1
	Connect WHITE wire from house wiring to WHITE wire range		RED
			GROUND
	hood wiring using an appropriate wire nut.
	Run RED wire from 14/3 cable through bend plate wiring opening
	120 VAC
	for hood control connection. See next page for RED wire HOUSE WIRING	14/3 CABLE
	connection.
	120 VAC POWER CABLE ENTERING THE SWITCH
	2-ROCKER
	SWITCH

		RED
		(motor)	GROUND
Install a 2-rocker switch at a convenient place for the	BLACK		14/3 CABLE
user. Feed the switch box with 120 VAC house wiring			TO HOOD
and use a 14/3 cable to wire it to the range hood (see			WHITE
diagram at right).		BLACK
		(lights)
			WHITE
			120 VAC
			LINE IN

Motor switch

Light switch

	NOTE: Allow enough length of 14/3 cable to perform the RED wire	4
	connection in the hood nose.
		TO CONTROL PANEL
	Insert the 14/3 cable in the hood through an UL approved wire	3
	clamp. Connect ground wire to the GREEN ground screw.	2
		MOTOR
	Connect WHITE wire from 14/3 cable to WHITE wire from range	GROUND
		WIRE
	hood wiring using an appropriate wire nut.
	Connect BLACK wire from 14/3 cable to BLACK wire from range		BLACK
			WHITE
	hood wiring using an appropriate wire nut.
		1	RED
	Run RED wire from 14/3 cable through bend plate wiring opening for		GROUND
	hood control connection. See next page for RED wire connection.
		14/3 CABLE

2