2800PSI
Owner’s Manual / Manual del Propietario
CAUTION
Before using this product, read this manual and follow all Safety Rules and Operating Instructions.
PRECAUCIÓN
Antes de utilizar el producto, lea este manual y siga todas las Reglas de Seguridad e Instrucciones de Uso.
Questions? Help is just a moment away! Preguntas? La ayuda es justa un momento lejos! Call: Pressure Washer Helpline
Llame: Línea Directa del Lavador a Presión - 1-800-743-4115 M-F 8-5 CT web: www.briggsandstratton.com
SpeedClean™ is a trademark of Briggs & Stratton Power Products. SpeedClean™ es una marca registrada de Briggs & Stratton Power Products.
BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC
JEFFERSON,WISCONSIN, U.S.A.
Model No. 020212-0 (2,800 PSI Pressure Washer) Manual No. 194445GS Revision 2 (04/12/2005)
SpeedClean™ 2800 PSI Pressure Washer
SAVE THESE INSTRUCTIONS
TABLE OF CONTENTS
Safety Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Know Your Pressure Washer. . . . . . . . . . . . . . . . . . . . . . . . 5
Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-12
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-15
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
EQUIPMENT
DESCRIPTION
Read this manual carefully and become familiar with your pressure washer. Know its applications, its limitations and any hazards involved.
This manual contains information for a high pressure washer that operates at 2,800 PSI at a flow rate of
2.5 gallons per minute.This powerful, high quality system features large 10” wheels, a pump equipped with an automatic cool down system, chemical injection system, nozzle extension with quick connect, quick connect spray tips, safety goggles, heavy duty 25’ hose and more.
Every effort has been made to ensure that information in this manual is accurate and current. However, we reserve the right to change, alter or otherwise improve the product and this document at any time without prior notice.
Copyright © 2005 Briggs & Stratton Power Products Group, LLC. All rights reserved. No part of this material may be reproduced or transmitted in any form by any means without the express written permission of Briggs & Stratton Power Products Group, LLC.
SAFETY RULES
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
The safety alert symbol (
) is used with a signal word (DANGER, CAUTION,WARNING), a pictorial and/or a safety message to alert you to hazards. DANGER indicates a hazard which, if not avoided, will result in death or serious injury. WARNING indicates a hazard which, if not avoided, could result in death or serious injury. CAUTION indicates a hazard which, if not avoided, might result in minor or moderate injury. CAUTION, when used without the alert symbol, indicates a situation that could result in equipment damage. Follow safety messages to avoid or reduce the risk of injury or death.
WARNING
The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
Hazard Symbols and Meanings
Toxic Fumes |
Electrical Shock |
Slippery Surface |
Fall |
Fluid Injection |
Fire |
Explosion |
Hot Surface |
Moving Parts |
Flying Objects |
Kickback |
2
SpeedClean™ 2800 PSI Pressure Washer
WARNING
Running engine gives off carbon monoxide, an odorless, colorless, poison gas.
Breathing carbon monoxide will cause nausea, fainting or death.
Some chemicals or detergents may be harmful if inhaled or ingested, causing severe nausea, fainting or poisoning.
•Operate pressure washer ONLY outdoors.
•Keep exhaust gas from entering a confined area through windows, doors, ventilation intakes or other openings.
•DO NOT operate pressure washer inside any building or enclosure.
•Use a respirator or mask whenever there is a chance that vapors may be inhaled.
•Read all instructions with mask so you are certain the mask will provide the necessary protection against inhaling harmful vapors.
WARNING
Use of pressure washer can create puddles and slippery surfaces.
High pressure spray could cause you to fall if you are too close to the cleaning surface.
•Keep spray nozzle between 8 to 24 inches away from cleaning surface.
•Operate this unit on a stable surface.
•The cleaning area should have adequate slopes and drainage to reduce the possibility of a fall due to slippery surfaces.
•Be extremely careful if you must use the pressure washer from a ladder, scaffolding or any other relatively unstable location.
•Firmly grasp spray gun with both hands when using high pressure spray to avoid injury if gun kicks back.
WARNING
Rapid retraction of starter cord (kickback) will pull hand and arm toward engine faster than you can let go.
Broken bones, fractures, bruises or sprains could result.
•When starting engine, pull cord slowly until resistance is felt and then pull rapidly to avoid kickback.
•If engine starts and fails to continue to run or if increased resistance is felt during starting pull attempts, squeeze trigger on spray gun.
WARNING
Fuel and its vapors are extremely flammable an explosive.
Fire or explosion can cause severe burns or death.
WHEN ADDING FUEL
•Turn pressure washer OFF and let it cool at least 2 minutes before removing gas cap.
•Fill fuel tank outdoors.
•DO NOT overfill tank.Allow space for fuel expansion.
•Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition sources.
•DO NOT light a cigarette or smoke.
WHEN OPERATING EQUIPMENT
•DO NOT tip engine or equipment at angle which causes fuel to spill.
•DO NOT spray flammable liquids.
WHEN TRANSPORTING OR REPAIRING EQUIPMENT
•Transport/repair with fuel tank EMPTY or with fuel shutoff valve OFF.
WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK
•Store away from furnaces, stoves, water heaters, clothes dryers or other appliances that have pilot light or other ignition source because they can ignite fuel vapors.
WARNING
The high pressure stream of water that this equipment produces can pierce skin and its underlying tissues, leading to serious injury and possible amputation.
Spray gun retains high pressure when pressure washer is shut down, which can cause injury.
•NEVER aim spray gun at people, animals or plants.
•DO NOT allow CHILDREN to operate pressure washer.
•NEVER repair high pressure hose. Replace it.
•NEVER repair leaking connections with sealant of any kind. Replace o-ring or seal.
•Keep high pressure hose connected to pump and spray gun while system is pressurized.
•Squeeze trigger on spray gun to relieve trapped pressure, every time you stop engine. Engage trigger lock on spray gun.
WARNING
Spray contact with electrical wiring can result in electrocution.
•Keep water spray away from electric wiring or fatal electric shock may result.
3
SpeedClean™ 2800 PSI Pressure Washer
WARNING
Running engines produce heat.Temperature of muffler and nearby areas can reach or exceed 150°F (65°C).
Severe burns can occur on contact.
Combustible debris, such as leaves, grass, brush, etc. can catch fire.
•DO NOT touch hot surfaces.
•Allow equipment to cool before touching.
•The pressure washer must be at least 5 feet from structures having combustible walls and/or other combustible materials.
•Keep at least 3 feet of clearance on all sides of pressure washer for adequate cooling, maintenance and servicing.
•In the State of California a spark arrester is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. If you equip the muffler with a spark arrester, it must be maintained in effective working order.
WARNING
Starter and other rotating parts can entangle hands, hair, clothing, or accessories.
•DO NOT wear loose clothing, jewelry or anything that may be caught in the starter or other rotating parts.
•Tie up long hair and remove jewelry.
WARNING
High pressure spray can cause paint chips or other particles to become airborne.
•Always wear eye protection when using this equipment or in vicinity of where equipment is in use.
WARNING
Unintentional sparking can result in fire or electric shock.
WHEN ADJUSTING OR MAKING REPAIRS TO YOUR PRESSURE WASHER
•Disconnect spark plug wire from spark plug and place wire where it cannot contact spark plug.
CAUTION
Excessively high or low operating speeds increase risk of injury and damage to pressure washer.
•DO NOT tamper with governed speed.
•DO NOT operate pressure washer above rated pressure.
CAUTION
A pressure washer produces a high pressure spray which increases risk of injury and damage to unit.
•DO NOT secure spray gun in open position.
•DO NOT leave spray gun unattended while machine is running.
•NEVER use a spray gun which does not have a trigger lock or trigger guard in place and in working order.
•Always be certain spray gun, nozzles and accessories are correctly attached.
CAUTION
High pressure spray may damage fragile items including glass.
•DO NOT point spray gun at glass when using 0° (pin point) spray tip.
•NEVER aim spray gun at plants.
CAUTION
Improper treatment of pressure washer can damage it and shorten its life.
•If you have questions about intended use, ask dealer or contact Briggs & Stratton Power Products.
•NEVER operate units with broken or missing parts, or without protective housing or covers.
•DO NOT by–pass any safety device on this machine.
•Before starting pressure washer in cold weather, check all parts of the equipment to be sure ice has not formed there.
•NEVER move machine by pulling on high pressure hose. Use handle provided on unit.
•Check fuel system for leaks or signs of deterioration, such as chafed or spongy hose, loose or missing clamps, or damaged tank or cap. Correct all defects before operating pressure washer.
•This equipment is designed to be used with Briggs & Stratton Power Products authorized parts ONLY. If equipment is used with parts that DO NOT comply with minimum specifications, user assumes all risks and liabilities.
4
SpeedClean™ 2800 PSI Pressure Washer
KNOW YOUR PRESSURE WASHER
Read this owner’s manual and safety rules before operating your pressure washer.
Compare the illustrations with your pressure washer to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.
Spray Gun
High Pressure Hose
Pump equipped with |
|
Automatic Cool Down System |
Water Inlet |
Air Filter — Protects engine by filtering dust and debris out of intake air.
Automatic Cool Down System — Cycles water through pump when water reaches 125°-155°F.Warm water will discharge from pump onto ground.This system prevents internal pump damage.
Chemical Injection Siphon/Filter — Use to siphon detergent or other pressure washer chemicals into the low pressure stream.
Choke Lever — Prepares a cold engine for starting.
Fuel Tank — Fill tank with regular unleaded pressure washer. Always leave room for fuel expansion.
Fuel Valve — Used to turn fuel on and off to engine.
High Pressure Hose — Connect one end to the water pump and the other end to the spray gun.
High Pressure Outlet — To connect high pressure hose.
Fuel Tank |
Throttle Lever |
|
|
|
Choke Lever |
|
Fuel Valve |
|
Recoil Starter |
|
(on front of engine) |
|
Air Filter |
|
Spray Tips |
Oil Fill Cap
Nozzle Extension with
Quick Connect
Chemical Injection |
High Pressure Outlet |
|
|
Siphon/Filter |
|
Nozzle Extension with Quick Connect — Allows you to switch between four different spray tips.
Oil Fill Cap — Fill engine with oil here.
Pump — Develops high pressure.
Recoil Starter — Use for starting the engine manually.
Safety Goggles (not shown) — Always use the enclosed goggles or other eye protection when running your pressure washer.
Spray Gun — Controls the application of water onto cleaning surface with trigger device. Includes safety latch.
Spray Tips — Chemical injection, 0°, 15°, and 40°: for various high pressure cleaning applications.
Throttle Lever—Sets engine in starting mode for recoil starter and stops a running engine.
Water Inlet — Connect garden hose here.
5
SpeedClean™ 2800 PSI Pressure Washer
ASSEMBLY
IMPORTANT: Read entire owner’s manual before you attempt to assemble or operate your new pressure washer.
Remove Pressure Washer From
Carton
1.Remove the parts bag, accessories, and inserts included with pressure washer.
2.Slice two corners at the end of carton from top to bottom so the panel can be folded down flat.
3.Remove pressure washer from carton.
Carton Contents
Items in the carton include:
•Main Unit
•Safety Goggles
•Handle
•High Pressure Hose
•Spray Gun
•Nozzle Extension with Quick Connect Fitting
•Oil Bottle
•Parts Bag (which includes the following):
•Owner’s Manual
•Engine Manual
•Owner’s Registration Card
•Bag containing 4 multi–colored Quick Connect Nozzles
•Handle Fastening Hardware Kit (which includes):
•Carriage Bolts (2)
•Plastic Knobs (2)
•“L” Bolts (2)
•Lock Nuts (2)
PREPARING PRESSURE WASHER FOR USE
If you have any problems with the assembly of your pressure washer or if parts are missing or damaged, call the pressure washer helpline at 1-800-743-4115. If calling for assistance, please have the model, revision, and serial number from the data tag available.
Perform these tasks to prepare unit for operation:
1.Fill out and send in registration card.
2.Attach handle to main unit.
3.Add oil to engine crankcase.
4.Add fuel to fuel tank.
5.Connect high pressure hose to spray gun and pump.
6.Connect water supply to pump.
7.Attach nozzle extension to spray gun.
8.Select/attach quick connect spray tip to nozzle extension.
Attach Handle to Unit
NOTE: All assembly operations given in this section will be described from the perspective of assembling the pressure washer from the rear.
1.Place handle assembly onto handle supports connected to main unit. Make sure holes in handle align with holes on handle supports (Figure 1).
Figure 1 — Attach Handle to Base
Handle
Align Holes
Handle
Supports
NOTE: It may be necessary to move the handle supports from side to side in order to align the handle so it will slide over the handle supports.
6
SpeedClean™ 2800 PSI Pressure Washer
2.Insert carriage bolts through holes from outside of the unit and attach a plastic knob from inside of unit (Figure 2).Tighten by hand.
Figure 2 — Secure Handle
3.Insert one “L” hook through hole just under billboard on left side of handle (viewing from rear of unit). Hold hook in place and attach a plastic knob from inside of unit (Figure 3).Tighten by hand.
Add Engine Oil and Fuel
• Place pressure washer on a level surface.
CAUTION
Any attempt to crank or start the engine before it has been properly filled with the recommended oil will result in equipment failure.
•Refer to engine manual for oil and fuel fill information.
•Damage to equipment resulting from failure to follow this instruction will void warranty.
•Refer to engine owner’s manual and follow oil and fuel recommendations and instructions.
NOTE: Check oil often during engine break–in. Refer to engine owner’s manual for recommendations.
Figure 3 — Attach “L” Hooks to Handle
Spray Gun
Hook
Hose Hook
Connect Hose and Water Supply to Pump
IMPORTANT: To avoid pump damage, you must assemble the nozzle extension to the spray gun and attach all hoses before you start the engine.
1.Uncoil high pressure hose and attach one end of hose to base of spray gun (Figure 4).Tighten by hand.
Figure 4 — Connect High Pressure Hose to Spray Gun
4.Insert other “L” hook through hole just above billboard on right side of handle (viewing from rear of unit). Hold hook in place and attach a plastic knob from inside of unit (Figure 3).Tighten by hand.
7
SpeedClean™ 2800 PSI Pressure Washer
NOTE: Remove and discard all pump shipping caps before attaching hoses.
2.Attach other end of high pressure hose to high pressure outlet on pump (Figure 5).Tighten by hand.
Figure 5 — Connect High Pressure Hose to Pump
3.Before connecting garden hose to water inlet, inspect inlet screen (Figure 6). Clean screen if it contains debris or replace if damaged. DO NOT run pressure washer if inlet screen is damaged.
Figure 6 — Connect the Garden Hose to Water Inlet
Inspect inlet screen, |
DO NOT use if |
damaged, clean if dirty. |
4.Run water through your garden hose for 30 seconds to clean out any debris.
IMPORTANT: DO NOT siphon standing water for the water supply. Use ONLY cold water (less than 100°F).
5.Connect garden hose (not to exceed 50 feet in length) to water inlet.Tighten by hand (Figure 6).
CAUTION
There MUST be at least ten feet of unrestricted garden hose between the pressure washer inlet and any flow shut off device, such as a ‘Y’ shut-off connector or other convenience-type water shut-off valve.
•Damage to equipment resulting from failure to follow this instruction will void warranty.
6.Turn ON water and squeeze trigger on gun to purge pump system of air and impurities.
WARNING
High pressure spray can cause paint chips or other particles to become airborne.
•Always wear eye protection when using this equipment or in vicinity of where equipment is in use.
•Before starting the pressure washer, be sure you are wearing adequate eye protection.
Checklist Before Starting Engine
Review the unit’s assembly to ensure you have performed all of the following.
1.Make sure handle is in place and secure.
2.Check that oil has been added to proper level in engine crankcase.
3.Add proper fuel to fuel tank.
4.Check for properly tightened hose connections.
5.Check to make sure that there are no kinks, cuts, or damage to the high pressure hose.
6.Provide a proper water supply at an adequate flow.
7.Be sure to read “Safety Rules” and “How To Use Your Pressure Washer” before using the pressure washer.
8
SpeedClean™ 2800 PSI Pressure Washer
HOW TO USE YOUR PRESSURE WASHER
If you have any problems operating your pressure washer, please call the pressure washer helpline at 1-800-743-4115.
Pressure Washer Location
Pressure Washer Clearance
WARNING
Running engine gives off carbon monoxide, an odorless, colorless, poison gas.
Breathing carbon monoxide will cause nausea, fainting or death.
•Operate pressure washer ONLY outdoors.
•Keep exhaust gas from entering a confined area through windows, doors, ventilation intakes or other openings.
•DO NOT operate pressure washer inside any building or enclosure.
The pressure washer must be at least 5 ft. (152 cm) from structures having combustible walls and/or other combustible materials. Leave at least 3 ft. (92 cm) all around pressure washer including overhead, for adequate cooling, maintenance and servicing.
Place pressure washer in a well ventilated area, which will allow for removal of deadly exhaust gas. DO NOT place pressure washer where exhaust gas could accumulate and enter inside or be drawn into a potentially occupied building. Ensure exhaust gas is kept away from any windows, doors, ventilation intakes or other openings that can allow exhaust gas to collect in a confined area
(Figure 7). Prevailing winds and air currents should be taken into consideration when positioning pressure washer.
Figure 7 — Pressure Washer Clearance
Typical Pressure
Washer Shown
Exhaust Port
How to Start Pressure Washer
To start your pressure washer for the first time, follow these instructions step-by-step.This starting information also applies if you have let the pressure washer sit idle for at least a day.
1.Place pressure washer near an outside water source capable of supplying water at a flow rate greater than 3.5 gallons per minute and no less than 20 PSI at pressure washer end of garden hose.
2.Check that high pressure hose is tightly connected to spray gun and pump. See “Preparing Pressure Washer for Use” for illustrations.
3.Make sure unit is in level position.
4.Connect garden hose to water inlet on pressure washer pump. Turn ON water.
CAUTION
DO NOT run the pump without the water supply connected and turned on.
•Damage to equipment resulting from failure to follow this instruction will void warranty.
5.Squeeze trigger on gun until you have a steady stream of water.This purges the pump of air and impurities.
6.Attach nozzle extension to spray gun (Figure 8). Tighten by hand.
Figure 8 — Connect Nozzle Extension to Spray Gun
7.Place colored quick connect spray tips in slots on holder that’s attached to nozzle extension (Figure 9).
Figure 9 — Install Spray Tips in Holder
8.Choose spray tip you want to use and insert it into nozzle extension. See “How to Use Spray Tips”.
9
SpeedClean™ 2800 PSI Pressure Washer
9.Engage safety latch to spray gun trigger (Figure 10).
Figure 10 — Spray Gun with Safety Latch Engaged
Safety Latch
10.Start engine according to instructions given in engine owner’s manual. Also see operating instructions tag located on the pressure washer.
WARNING
Rapid retraction of starter cord (kickback) will pull hand and arm toward engine faster than you can let go.
Broken bones, fractures, bruises or sprains could result.
•When starting engine, pull cord slowly until resistance is felt and then pull rapidly to avoid kickback.
•If engine starts and fails to continue to run or if increased resistance is felt during starting pull attempts, squeeze trigger on spray gun.
NOTE: Always keep the throttle lever in the “Fast” position when operating the pressure washer.
WARNING
Running engines produce heat.Temperature of muffler and nearby areas can reach or exceed 150°F (65°C).
Severe burns can occur on contact.
Combustible debris, such as leaves, grass, brush, etc. can catch fire.
•DO NOT touch hot surfaces.
•Allow equipment to cool before touching.
•The pressure washer must be at least 5 feet from structures having combustible walls and/or other combustible materials.
•Keep at least 3 feet of clearance on all sides of pressure washer for adequate cooling, maintenance and servicing.
•In the State of California a spark arrester is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. If you equip the muffler with a spark arrester, it must be maintained in effective working order.
How to Stop Your Pressure Washer
1.Let engine idle for two minutes.
2.Turn engine off according to instructions given in engine owner’s manual.
3.Squeeze trigger on spray gun to relieve trapped pressure in hose to avoid injury.
NOTE: A small amount of water will squirt out when pressure is released.
WARNING
The high pressure stream of water that this equipment produces can pierce skin and its underlying tissues, leading to serious injury and possible amputation.
Spray gun retains high pressure when pressure washer is shut down, which can cause injury.
•Keep high pressure hose connected to pump and spray gun while system is pressurized.
•Squeeze trigger on spray gun to relieve trapped pressure, every time you stop engine. Engage trigger lock on spray gun.
4.Engage trigger lock on spray gun when not in use.
How to Use Spray Tips
The quick–connect on the nozzle extension allows you to switch between four different quick connect spray tips.The spray tips vary the spray pattern as shown (Figure 11).
CAUTION
A pressure washer produces a high pressure spray which increases risk of injury and damage to unit.
•NEVER exchange spray tips without locking the safety latch on the trigger.
Follow these instructions to change spray tips:
1.Engage safety latch on spray gun.
2.Pull back collar on quick–connect and pull current spray tip off. Store spray tips in slots on holder that’s attached to nozzle extension.
3.Select desired spray tip:
•For gentle rinse, select white 40° spray tip.
•To scour surface, select yellow 15° or red 0° spray tip.
•To apply chemical, select black spray tip.
10
SpeedClean™ 2800 PSI Pressure Washer
Figure 11 — Spray Tip Spray Patterns
Low Pressure
Black
Use to apply chemical
High Pressure
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
15° Yellow |
|
|
|
|
0° Red |
||||||||||||||||
40° White |
|
|
|
|
|
||||||||||||||||||||||||||||||
4.Pull back on collar, insert new spray tip and release collar.Tug on spray tip to make sure it is securely in place.
5.For most effective cleaning, keep spray tip from 8 to 24 inches away from cleaning surface. If you get spray tip too close, you may damage cleaning surface.
6.DO NOT get closer than 6 inches when cleaning tires.
Cleaning and Applying Chemical
IMPORTANT: Use soaps designed specifically for pressure washers. Household detergents could damage the pump.
CAUTION
You must attach all hoses before you start the engine.
•Starting the engine without all the hoses connected and without the water turned ON will damage the pump.
•Damage to equipment resulting from failure to follow this instruction will void warranty.
To apply detergent follow these steps:
1.Review the use of spray tips.
2.Prepare detergent solution as required by manufacturer.
3.Place chemical injection siphon/filter into detergent container.
CAUTION
Keep the chemical injection tube from coming in contact with the hot muffler.
•When inserting the filter into a detergent solution bottle, route the tube so as to keep it from inadvertently contacting the hot muffler.
4.Make sure black spray tip is installed.
NOTE: Detergent cannot be applied with the high pressure spray tips (White,Yellow, or Red).
5.Make sure garden hose is connected to water inlet. Check that high pressure hose is connected to spray gun and pump and start engine.
6.Apply detergent to a dry surface, starting at lower portion of area to be washed and work upward, using long, even, overlapping strokes.
7.Allow detergent to soak in between 3–5 minutes before washing and rinsing. Reapply as needed to prevent surface from drying. DO NOT allow detergent to dry on (prevents streaking).
IMPORTANT: You must flush the chemical injection system after each use by placing the filter into a bucket of clean water, then run the pressure washer in low pressure for 1-2 minutes.
11
Loading...