Breville Consumer Service Center
USA |
|
Canada |
|
Mail: |
Breville USA |
Mail: |
Breville Canada |
|
19400 S. Western Ave |
|
2555, Avenue de l’Aviation |
|
Torrance CA |
|
Pointe-Claire (Montreal) |
|
90501-1119 |
|
Quebec H9P 2Z2 |
Phone: |
1-866-273-8455 |
Phone: |
1-855-683-3535 |
|
1-866-BREVILLE |
|
|
Email: |
askus@brevilleusa.com |
Email: |
askus@breville.ca |
www.breville.com
Breville is a registered trademark of Breville Pty. Ltd. A.B.N. 98 000 092 928.
Copyright Breville Pty. Ltd. 2012.
Due to continued product improvement, the products illustrated/photographed in this booklet may vary slightly from the actual product.
the Dual Boiler™
Instruction Booklet - Livret d’instructions
Model BES900XL /B Issue - D12 |
BES900XL /B |
Contents
CONGRATULATIONS
on the purchase of your Breville product
Register online for product support and exclusive offers.*
USA Consumers: www.brevilleusa.com
Canadian Consumers: www.breville.ca
*Registering is not a substitute for proof of purchase when submitting a Warranty Claim.
4 Breville recommends safety first
6 Know your Breville Dual Boiler™
10Operating your Breville Dual Boiler™
24 Coffee making tips & preparation
28 Care & cleaning
32 Troubleshooting
38 Coffees to try
40 French
3
Breville recommends safety first
At Breville we are very safety conscious. We design and manufacture consumer products with the safety of you, our valued customer, foremost in mind. In addition we ask that you exercise a degree of care when using any electrical appliance and adhere to the following precautions.
Important safeguards
When using electrical appliances, basic safety precautions should always be followed, including the following:
•Carefully read all instructions before operating and save for future reference.
•Remove any packaging material and promotional labels or stickers before using the espresso machine for the first time.
•Do not place the espresso machine near the edge of a bench or table during operation. Ensure the surface is level, clean and free of water and other substances.
•Do not place the espresso machine on or near a hot gas or electric burner, or where it could touch a heated oven.
•Do not use the espresso machine on metal surfaces, for example, a sink drain board.
•Always ensure the espresso machine is properly assembled before connecting to power outlet and operating.
•The appliance is not intended to be operated by means of an external timer or separate remote control system.
•Use only cold, preferably filtered water in the water tank. Do not use any other liquid. We do not recommend the use of de-mineralized or distilled water as this may affect the taste of the coffee and how the espresso machine is designed to function.
•Never use the espresso machine without water in the water tank.
•Ensure the portafilter is firmly inserted and secured into the group head before using the machine. It should be rotated to the right until the handle is past the center and is securely locked in place.
Rotating past the center will not damage the silicone seal.
•Never remove the portafilter during the brewing operation as the machine
is under pressure.
•Do not touch hot surfaces. Use handles or knobs. Allow the espresso machine to cool down before moving or cleaning any parts.
•Do not leave the espresso machine unattended when in use.
•Do not place anything other than cups for warming on top of the espresso machine.
•Always switch Off the espresso machine by pressing the Power button to Off and unplug if appliance is to be left unattended, not in use, before
cleaning, before attempting to move the appliance, disassembling, assembling and when storing the appliance.
•Keep the appliance and accessories clean. Follow the cleaning instructions provided in this book.
•The use of accessory attachments not recommended by Breville may result in fire, electric shock or injury to persons.
IMPORTANT SAFEGUARDS FOR ALL ELECTRICAL APPLIANCES
•Fully unwind cord before use.
•To protect against electric shock, do not immerse cord, plug or appliance in water or any other liquid.
•Do not let the cord hang over the edge of a bench or table, touch hot surfaces, or become knotted.
Breville recommends safety first
•This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
•Children should be supervised to ensure they do not play with the appliance.
•This appliance is recommended for household use only. Do not use this appliance for anything other than its intended use. Do not use in moving vehicles or boats. Do not use outdoors.
•It is recommended to regularly inspect the appliance. Do not use the appliance if the power cord, power plug, or appliance becomes damaged in anyway. Immediately cease use and call Breville Consumer Service for examination, repair or adjustment.
•For any maintenance other than cleaning, visit www.Breville.com or call Breville Consumer Service.
•This appliance is equipped with a power cord having a grounding wire with a grounding plug. The appliance must be grounded using a 3-hole properly grounded outlet. In the event of an electrical short circuit, grounding reduces the risk of electrical shock.
•If the appliance is of the grounded type, the extension cord should be a grounding 3-wire cord. If the power outlet is a standard 2-prong wall outlet, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.
•Do not, under any circumstances, cut or remove the third (ground) prong from the power cord or use an adapter.
•Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded.
WARNING
Fully unwind the cord before use. short cord instructions
Your Breville appliance is fitted with a short power supply cord as a safety precaution to prevent personal injury or property damage resulting from pulling, tripping or becoming entangled with a longer cord. Do not allow children to use or be near this appliance without close adult supervision.
Longer detachable power supply cords or extension cords are available and may be used if care is exercised. If an extension cord is used, (1) the marked electrical rating of the cord set or extension cord should be at least as great as the electrical rating of the appliance, (2) the cord should be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped over unintentionally and (3) the extension cord must include a 3-prong grounding plug.
CSA Duty Cycle Marking:
The Canadian Standards Authority requires any appliances capable of drawing over 1500W to be marked with a ‘duty cycle’ in minutes. For the BES900XL, this ‘duty cycle’ represents the maximum time for which the appliance will draw over 1500W during any 2 hour period of use. It does not indicate the appliance is unsafe for continuous use or is required to be switched off at certain intervals during normal use.
CALIFORNIA PROPOSITION 65:
(Applicable to California residents only).
This product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
FOR HOUSEHOLD USE ONLY SAVE THESE INSTRUCTIONS
4 |
5 |
KNOW
your Breville Dual Boiler™
FEATURES OF YOUR Breville Dual Boiler™
TRIPLE HEAT SYSTEM
Dual Stainless Steel Boilers
Dedicated espresso and steam boilers for simultaneous milk texturing and espresso extraction at the optimum temperature.
Actively Heated Group Head
Commercial 58mm group head with embedded element for optimal thermal stability during extraction.
Precision control
Electronic PID Temperature Control
Electronic temperature control delivers precise water temperature to 1°F (1°C) for optimum espresso flavor. User programmable.
Regulated Extraction Pressure
15 bar Italian pump with over-pressure valve (OPV) limits the maximum pressure throughout extraction to optimum levels.
Low Pressure Pre-Infusion
Gradually increases water pressure to gently expand grinds for an even extraction.
User programmable.
Dual Pumps
Dedicated espresso and steam boiler pumps help maintain constant pressure throughout extraction.
Programmable Shot Temp
Allows user to adjust water temperature to achieve optimal espresso flavor.
Additional features
LCD Interface
Displays current settings and simplifies programming functions.
High Volume Instant Steam
Dedicated 32 fl. oz (950ml) steam boiler delivers instant and continuous steam.
Commercial Steam Wand
Stainless steel 360° swivel-action steam wand with 3 hole tip for a silkier texture.
Volumetric Control
Manual or programmed 1 & 2 cup shot volumes. User programmable.
Instant Hot Water
Dedicated Hot Water outlet for making Americanos or pre-heating cups.
58mm Full Stainless Steel Portafilter
Helps to promote a more even extraction and is easier to clean.
Shot Clock
Displays duration of the espresso shot being extracted.
7
Know your Breville Dual Boiler™
All parts of the Dual Boiler™ that come into contact with coffee and water are BPA Free.
2 |
9 |
|
3 |
|
|
4 |
10 |
|
|
||
5 |
11 |
|
6 |
||
|
||
7 |
12 |
|
8 |
13 |
|
1 |
||
|
||
|
14 |
|
Register your unique serial number |
15 |
|
at www.breville.com for exclusive |
||
product support. |
|
|
Your serial number can be located |
16 |
|
when you remove the rear water tank. |
||
Include all numbers, hyphens and |
17 |
|
“US/CN” when registering. |
||
“0” = the number zero. |
|
1.Rear 84 fl.oz (2.5L) removable water tank with integrated water filter.
2.Top-fill water tank lid
3.Hot water dial
4.Backlit LCD interface displays current settings and simplifies programming functions.
5.Espresso pressure gauge monitors extraction pressure.
6.Integrated & removable 58mm tamper
7.Actively heated 58mm group head with embedded element for thermal stability during extraction.
8.58mm full stainless steel portafilter
9.6 cup warming tray
10.Manual and programmable 1 & 2 cup buttons control extraction volume.
11.Easy to operate steam lever for instant and continuous steam.
12.Dedicated hot water outlet delivers instant hot water for Americanos & pre-heating cups.
13.360° swivel action steam wand with 3 hole tip for a silkier texture.
14.Backlit water level indicator
15.Storage tray houses accessories when not in use.
16.Drop down swivel foot for easy maneuverability.
17.Removable drip tray with Empty Me! indicator.
NOT SHOWN
15 bar Italian pump
Dual stainless steel boilers Electronic PID temperature control Over-pressure valve (OPV)
Low pressure pre-infusion
Know your Breville Dual Boiler™
18
|
21 |
|
22 |
19 |
|
20 |
23 |
|
Power save mode powers down and switches machine off.
Safety thermal cut-out protection
Accessories
18.Stainless steel frothing jug
19.Cleaning disc
20.Cleaning tablets
21.Dual wall filter basket (2 cup)
22.Dual wall filter basket (1 cup)
23.Allen key
24.Single wall filter basket (2 cup)
25.Single wall filter basket (1 cup)
26.Cleaning tool
27.Water filter holder and filter
24
25
26 |
27 |
|
LCD INTERFACE
Display Modes
•Shot Temp
•Shot Clock Timer
•Clock
Programmable Functions
•Shot Temp
•Shot Volume - 1 & 2 cup
•Pre-Infusion duration & power
•Auto Start
•Temperature Unit - ˚F/˚C
•Audio Volume
8 |
|
9 |
|
|
|
OPERATING
your Breville Dual Boiler™
Operating your Breville Dual Boiler™
BEFORE FIRST USE
Machine Preparation
Remove and discard all labels and packaging materials attached to your espresso machine. Ensure you have removed all parts and accessories before discarding the packaging.
Remove the water tank located at the back of the machine by pulling down the water tank handle. Remove the plastic bag containing the water filter and water filter holder. Clean parts and accessories (water tank, portafilter, filter baskets, jug) using warm water and a gentle dish washing liquid, then rinse well.
Conditioning the Water Filter
•Soak the water filter in a cup of water for 5 minutes, then rinse under cold running water.
•Wash the water filter holder with cold water, taking specific care to rinse the stainless steel mesh.
•Insert the water filter into the two parts of the water filter holder.
•Set Date Dial 2 months ahead
•To install the assembled water filter holder into the water tank, align the base of the water filter holder with the adapter inside the water tank. Push down to lock into place.
•Slide the water tank back into position at the back of the machine by pushing then lifting up the water tank handle.
CAUTION
Do not descale this machine. Use the provided water filter especially if you have hard water. Change every 2 months. Contact Breville Consumer Service or visit www.breville.com for replacement filters or for advice.
|
|
REPLACEMENT DUE |
|
Remove tank & filter holder Soak new filter for |
Rinse new filter & mesh |
Place filter into filter holder Set date 2 months ahead |
Install filter & replace tank |
5 minutes |
|
|
|
11
Operating your Breville Dual Boiler™
FIRST USE
Initial Start Up
•Fill water tank with cold, preferably filtered water. You can do this by either opening the top-fill water tank lid (push to open), or by removing the water tank at the back of the machine.
CAUTION
We recommend using cold, filtered water. We do not recommend the use of de-mineralized or distilled water as this may affect the taste of the coffee and how the machine is designed
to function.
•Check STEAM LEVER and HOT WATER dial are in the CLOSED position.
•Press the POWER button to switch the machine On. The POWER button will flash and the LCD screen will display the current espresso boiler temperature.
•A pumping sound will be heard indicating empty boilers are being filled with water for the first time. This is normal.
•When the machine has reached the default operating temperature (200˚F / 93˚C), the POWER button light will stop flashing and the MANUAL, 1 CUP and 2 CUP buttons will illuminate. The machine is now in STANDBY mode, ready for the next step ‘Flushing The Machine’.
NOTE
If the machine does not enter STANDBY mode, the boilers may need further “priming”. Rotate the HOT WATER dial to the OPEN position. When water starts to flow from the Hot Water outlet, rotate the HOT WATER dial to the CLOSED position.
Flushing The Machine.
When the machine has reached STANDBY mode, run the following 3 steps:
1.Press 2 CUP button to run water through group head.
2.Rotate HOT WATER dial to the OPEN position and run for 30 seconds.
3.Move STEAM LEVER to the OPEN position and run for 10 seconds.
Repeat this cycle until tank is empty.
TIP
To easily maneuver your machine, use the drop down swivel foot located under the drip tray. When turned to the UNLOCK position, the swivel foot drops down and lifts the machine upwards, making it easier to access the rear water tank or reposition the machine to another location.
START UP
Press the POWER button to switch the machine On. The POWER button will flash and the LCD screen will display the current espresso boiler temperature.
When the machine has reached the default operating temperature (200˚F / 93˚C), the POWER button light will stop flashing and the MANUAL, 1 CUP and 2 CUP buttons will illuminate. The machine is now in STANDBY mode ready for use.
Operating your Breville Dual Boiler™
NOTE
The machine is in START UP mode when the POWER button light is flashing. During this time, the MANUAL, 1 CUP and 2 CUP buttons will be disabled. Similarly, if you press the MENU button during START UP mode and select SHOT VOL or CLEAN CYCLE, the LCD screen will display BUSY.
Always wait until the machine is in STANDBY mode. This is when the POWER button light stops flashing and the MANUAL, 1 CUP and 2 CUP buttons illuminate.
POWER SAVE MODE
The machine will enter POWER SAVE mode after remaining idle for 1 hour and turn Off completely if not used for a continuous
4 hour period (refer to ‘Auto Power Off’, page 21).
Pressing any button during POWER SAVE mode (except POWER), or operating the STEAM LEVER or HOT WATER dial will cause the machine to enter START UP mode.
Pressing the POWER button during POWER SAVE will turn the machine Off.
LCD INTERFACE
Display modes
3 modes can be displayed on the LCD screen: Shot Temp, Shot Clock or Clock.
Press UP or DOWN arrow to change the display mode.
1. Shot Temp
Displays selected extraction temperature. The default is set at 200°F (93°C), but can be changed from 190°F - 205°F (86°C - 96°C).
See ‘Extraction Temperature’, page 16.
2. Shot Clock
Displays duration of current espresso extraction in seconds. See ‘Extraction Guide’, page 27.
3. Clock
Displays current time. The default is 12:00AM if the time has not been set. See ‘Set Clock’, page 17.
12 |
|
13 |
|
|
|
Operating your Breville Dual Boiler™
GENERAL OPERATION
1 CUP BUTTON
Press 1 CUP button once to extract a single shot of espresso at the pre-programmed volume (approx. 1oz / 30ml). The extraction will start using the low pressure pre-infusion.
The machine will stop after 1 CUP volume has been extracted and will return to STANDBY mode.
2 CUP BUTTON
Press 2 CUP button once to extract a double shot of espresso at the pre-
programmed volume (approx. 2oz / 60ml). The extraction will start using the low pressure pre-infusion.
MANUAL BUTTON
The MANUAL button allows you to control the espresso pour volume to suit your preference.
Press MANUAL button once to start the espresso extraction. The extraction will start using the low pressure pre-infusion.
Press MANUAL button again to stop extraction.
NOTE
To stop an extraction at any time, press the 1 CUP, 2 CUP or MANUAL button and the machine will return to STANDBY mode.
NOTE
To reprogram the 1 CUP or 2 CUP pour volume to suit your preference, refer to ‘Shot Volume’, page 16.
The machine will stop after 2 CUP volume has been extracted and will return to STANDBY mode.
Operating your Breville Dual Boiler™
Steam
For instant steam, move STEAM LEVER to OPEN position. The STEAM LED will illuminate.
To turn steam off, move STEAM LEVER to CLOSED position. The machine will return to STANDBY mode.
CAUTION: BURN HAZARD
Pressurized steam can still be released, even after machine has been switched off.
Children must always be supervised.
Hot Water
For instant hot water, rotate the HOT WATER dial to OPEN position. The HOT WATER LED will be On.
To turn hot water off, rotate the HOT WATER dial to CLOSED position. The machine will return to STANDBY mode.
NOTE
The HOT WATER dial will cease to dispense hot water after approx.
30 seconds. Depending on the size of your cup, you may need to close, then re-open the HOT WATER dial. See ‘HOT WATER LED Flashing’, page 21.
NOTE
You cannot run hot water and extract espresso at the same time.
LCD PROGRAMMING FUNCTIONS
To program the machine, press MENU button once. The LCD will display all programming functions. Continue to press MENU button until the function you’d like to program is flashing.
At any stage during programming, press EXIT to return to STANDBY mode.
NOTE
The MENU button is disabled during an extraction pour, or when the STEAM LEVER or HOT WATER dial are OPEN.
14 |
|
15 |
|
|
|
Operating your Breville Dual Boiler™
SHOT VOLUME
1 CUP Volume Programming
Press MENU button until SHOT VOL icon flashes and 1 CUP is displayed on the LCD screen.
Press 1 CUP button to start espresso extraction. Press 1 CUP again once desired volume of espresso has been extracted.
The machine will beep twice. Press the EXIT button to set the new 1 CUP volume.
Extraction temperature
Press MENU button until SHOT TEMP icon flashes. The LCD will display the current shot temperature setting.
2 CUP Volume Programming
Press MENU button until SHOT VOL icon flashes and 2 CUP is displayed on the LCD screen.
Press 2 CUP button to start espresso extraction. Press 2 CUP again once desired volume of espresso has been extracted.
The machine will beep twice. Press the EXIT button to set the new 2 CUP volume.
NOTE
To reset machine to original default settings, refer to ‘Resetting Default Settings’, page 19.
Press UP or DOWN arrow to adjust SHOT TEMP to the desired setting. The default is set at 200°F (93°C) but can be changed from 190°F - 205°F (86°C - 96°C).
The new SHOT TEMP setting will be displayed on the LCD screen. Press the EXIT button to set the new extraction temperature.
The optimum temperature will depend on the origin of the coffee beans, their freshness and degree of roast.
We recommend a temperature range between 194°F - 203°F (90°C - 95°C) for optimal flavor.
Operating your Breville Dual Boiler™
Set Clock
Setting the clock is optional. Press MENU button until SET CLOCK icon flashes.
The default is 12.00AM if time has not been set.
Press UP or DOWN arrow to adjust
the time. For faster scrolling, press and hold the UP or DOWN arrow. Press the EXIT button to set the clock.
AUTO START
Auto Start is optional. It allows you to program the specific time when the machine will automatically turn on. By programming your machine, you will not have to wait for it to pre-heat. We recommend programming the machine to start 30 minutes before you plan to use it.
Auto Start - turning the feature ON/OFF
Press MENU button until AUTO START icon flashes and the current Auto Start setting (ON or OFF) is displayed on the LCD screen.
Press UP or DOWN arrow to set the AUTO START to ON or OFF.
16 |
|
17 |
|
|
|
Operating your Breville Dual Boiler™
If AUTO START is ON, the LCD will display a clock icon.
Auto Start - Setting the ON time
Ensure Auto Start is set to ON.
Press MENU button until AUTO START icon flashes and the current Auto Start time is displayed on the LCD screen.
The default AUTO START time is 7:00AM.
Clean Cycle
Select this feature when the LCD screen displays CLEAN ME! Refer to page 22 and 29 for instructions.
Press UP or DOWN arrow to adjust
AUTO START to the desired time. For faster scrolling, press and hold the UP or DOWN arrow. Press the EXIT button to set the new Auto Start time.
Operating your Breville Dual Boiler™
Resetting Default Settings
The machine has the following default settings:
1.Temperature – 200°F (93°C)
2.Pre-Brew Infusion – PP60, Pd07 seconds
3.Auto Start - OFF
4.Auto Start Time - 7.00AM
5.Audio - LO
6.Clock – 12:00am
7.Temperature Unit – Fahrenheit
8.Auto Power Off – On
9.1 CUP default volume
-approx. 1oz/30ml
10.2 CUP default volume
-approx. 2oz/60ml
To reset machine to original default settings, first ensure machine is switched Off. Press and hold 1 CUP & 2 CUP buttons and then press the POWER button.
The LCD will display REST. All programmed settings will be reset to the original default settings.
ADVANCED FUNCTIONS
Press & Hold - 1 CUP
Press & hold 1 CUP button to deliver water to the group head at full pump pressure and release button to stop extraction.
This by-passes the pre-infusion step and delivers water to the group head at full pump pressure. This function can be used when purging the group head.
Press & Hold - 2 CUP
Press & hold 2 CUP button to deliver water to the group head at full pump pressure and release button to stop extraction.
This by-passes the pre-infusion step and delivers water to the group head at full pump pressure. This function can be used when purging the group head.
Press & Hold - MANUAL
Press & hold the MANUAL button to deliver water to the group head at low pre-infusion pressure. When MANUAL button is released, water will continue at full pump pressure. Press MANUAL button again to stop extraction.
This function can be used to manually control the pre-infusion duration.
The machine will return to STANDBY mode.
18 |
|
19 |
|
|
|
Operating your Breville Dual Boiler™
AdvanceD programming
Pre-Infusion Programming
Press UP and DOWN arrows together to enter PRE-INFUSION programming mode.
Press MENU button to move between Pre-Infusion Duration (Pd) and Pre-Infusion Power (PP).
Pre-Infusion Duration (Pd)
The LCD will display the current Pre-Infusion Duration.
Press UP or DOWN arrow to vary time.
We recommend a range between 5-15secs as being optimum. Press EXIT button to set the new Pre-Infusion Duration.
Pre-Infusion Power (PP)
The LCD will display current
Pre-Infusion Power as a percentage of total pump power.
Press UP or DOWN arrow to vary power.
We recommend a range between 55-65 as being optimum. Press EXIT button to set the new Pre-Infusion Power.
Temperature Unit - ˚F/˚C
Press POWER button to switch machine Off.
While holding DOWN arrow, press the POWER button. The LCD will display the current temperature unit (˚F or ˚C).
Press UP or DOWN arrow to select desired temperature unit. Press the EXIT button to set the new temperature unit.
Machine Audio
Machine Audio refers to the volume level of the ‘beeps’ heard.
• |
HI |
- high volume |
• |
LO |
- low volume |
•OFF - no volume
Press POWER button to switch machine Off.
While holding UP arrow, press the POWER button. The LCD will display the current audio volume.
Press UP or DOWN arrow to select desired volume. Press the EXIT button to
set the new volume.
Operating your Breville Dual Boiler™
Auto Power Off
The AUTO POWER Off feature will switch the machine Off if it remains idle for more than 4 hours.
To disable this feature so the machine remains On continuously, do the following:
Ensure machine is switched Off. Hold down MENU button and press POWER button.
The current AUTO POWER OFF setting (ON or OFF) will flash on the LCD screen.
Press UP or DOWN arrow to select AUTO POWER ON or OFF. Press EXIT button to set.
ALERTS
STEAM LED Flashing At START UP
The machine will not enter START UP mode when the STEAM LEVER is in the OPEN position and the STEAM LED is flashing.
Move the STEAM LEVER to the CLOSED position for the machine to enter START UP mode.
HOT WATER LED Flashing At START UP
The machine will not enter START UP mode when the HOT WATER dial is in the OPEN position and the HOT WATER LED is flashing.
Move the HOT WATER dial to the CLOSED position for the machine to enter START UP mode.
HOT WATER LED Flashing
The HOT WATER LED will flash when the hot water function has been operating for longer than approx. 30 seconds.
Hot water will cease to dispense. Move the HOT WATER dial to the CLOSED position, then back to the OPEN position if more hot water is required.
Fill Tank
The machine will detect a low water level. The FILL TANK icon will be displayed on the LCD screen. Add water to the tank.
20 |
|
21 |
|
|
|
Operating your Breville Dual Boiler™
Clean Me!
The machine will detect when 200 extractions have been carried out since the last clean cycle.
The CLEAN ME! icon will be displayed on the LCD screen the next time the machine enters START UP mode.
For information on how to clean the machine, refer to ‘Cleaning Cycle’, page 29.
Service
To ensure a long life of optimal brewing and steaming performance, it is important the machine is serviced by an authorized Breville service agent when the ‘SERVICE’ prompt scrolls across the LCD screen.
The ‘SERVICE’ prompt will appear after 6,000 cycles - approximately 4-5 years of regular use in a domestic environment. The frequency of this prompt will depend on your frequency of use.
Contact Breville Consumer Service for advice.
22 |
|
23 |
|
|
|
Loading...