Boss Audio BV9150 User Manual

User’s Manual

BV9150

MP3-COMPATIBLE DOUBLE-DIN

IN-DASH DVD/MP3/CD AM/FM

RECEIVER WITH 4.5" (114mm)

WIDESCREEN TOUCHSCREEN

TFT MONITOR

WITH USB AND SD MEMORY CARD

PORTS AND FRONT PANEL AUX INPUT

BV9150

MP3-COMPATIBLE DOUBLE-DIN IN-DASH DVD/MP3/CD AM/FM RECEIVER WITH 4.5" (114mm) WIDESCREEN TOUCHSCREEN TFT MONITOR

WITH USB AND SD MEMORY CARD PORTS AND

FRONT PANEL AUX INPUT

02.2012

3451 Lunar Court • Oxnard, CA 93030

iPod® is a trademark of Apple, Inc. registered in the U.S. and other countries.

tech support: www.bossaudio.com/support

BOSS Audio Systems

www.bossaudio.com

800.999.1236

Boss Audio Systems is not affiliated with Apple, Inc.

To ensure safety while driving

and to comply with laws,

drivers should not watch video or

operate the video device while driving.

4.5" In-Dash Double-DIN DVD/MP3/CD Receiver with USB, SD Memory Card

Ports and Front Panel AV Input

1. HANDLING COMPACT DISCS

MOISTURE CONDENSATION

On a rainy day or in a very damp area, moisture may condense on the lenses inside the unit. Should this occur, the unit will not operate properly. In such a case, remove the disc and wait for about an hour until the moisture has evaporated.

NOTES ON CDs

A dirty or defective disc may cause sound dropouts while playing. To enjoy optimum sound, handle the disc as follows. Handle the disc by its edge. To keep the disc clean, do not touch the surface (P.1).

P. 1

Do not stick paper or tape on the disc (P.2).

P. 2

Do not expose the discs to direct sunlight or

heat sources such as hot air-ducts, or leave them in a car parked in direct sunlight where there can be a considerable rise in temperature inside the car (P.3).

P. 3

Before playing, clean the discs with an

optional cleaning cloth. Wipe each disc from the centre out (P.4).

P. 4

Do not use solvents such as benzine,

thinner,commercially available cleaners, or antistatic spray intended for analog discs.

NOTES ON DISCS

If you use the discs explained below, the sticky residue can cause the CD to stop spinning and may cause malfunction or ruin your discs.

Do not use CDs that have a sticky residue on the surface (for example, from peeled-off stickers or from ink, or glue leaking from under the stickers).

Paste or sticky residue.

P. 5

****

*******

Do not use CDs with old labels that are beginning to peel off.

Stickers that are beginning to peel away leave a sticky residue (P.6).

P. 6

**************

*******

Do not use CDs with labels or stickers attached.

Labels are attached (P.7).

P. 7

*******

Do Not Use Special Shape CDs

Be sure to use round shape CDs only. Do not use any special shape CDs. Use of special shape CDs may cause the unit to malfunction.(P.8).

P. 8

CD-Rs and CD-RWs which have not undergone finalization processing cannot be played. (For more information on finalization processing, refer to the manual for your CD-R/CD-RW writing software or CD-R/CD-RW recorder.) Additionally, depending on the recording status, it may prove impossible to play certain CDs recorded on CD-R or CD-RW.

2. INSTALLATION

Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and system work properly. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle. Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a sudden stop, like an emergency stop. If installation angle exceeds 30 from horizontal, the unit might not give its optimum performance.

Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from heater, or where it would be subject to dust dirt or excessive vibration. Be sure to remove the front panel before installing the unit.

SUB-W OUT

BACKSIGHT RCA

DIN FRONT/REAR-MOUNT

This unit can be property installed either from Front (conventional DIN Front-mount) or Rear (DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods A and B.

DIN FRONT-MOUNT (Method A) Installation the unit

178

1. Dashboard

2. Screw

ANTENNA JACK

A/V IN (VIDEO IN) A/V IN (AUDO LEFT) A/V IN (AUDIO RIGHT)

VIDEO OUT (1 & 2) REAR LINE OUT LEFT & RIGHT FRONT LINE OUT LEFT & RIGHT

100

1. Dashboard

2. Nut (5mm)

3. Spring washer

4. Screw (5x15mm)

5. Screw

6. Support Strap Be sure to use the support strap to secure the

back of the unit in place. The strap can be bent by hand to the desired angle.

7. Plain washer

Trim Plate Installation: Push the trim plate against the chassis until it is fitted.

You must do this before you install the front panel, otherwise it can't be attached.

DIN REAR-MOUNT (METHOD B)

Installation using the screw holes on the sides of the unit. Fastening the unit to the factory radio mounting bracket.

Factory radio mounting bracket

Screw

Hook

Screw

Dashboard or console

DETACHABLE CONTROL PANEL (D.C.P.)

Removing The Detachable Control Panel (D.C.P.).

1. Turn the power off

2. Press the D.C.P. release button

PANEL RELEASE BUTTON

Attaching the DCP

3. Remove the D.C.P.

1. Attach the panel at the right side first, with point B on the main unit touching point A on the D.C.P. (As shown on the digram).

2. Then press the left side of D.C.P. onto the

main unit until a click sound is heard.

Note: the mounting box, outer trim ring,and half-sleeve are not used for this installation.

Note: The mounting box, metal half sleeve, hook & screws are not included in the packnig.

CAUTION

DO NOT insert the D.C.P from the left side. Doing so may damage it. The D.C.P can easily be damaged by shocks. After removing it, place it in a protective case and be careful not to drop it or subject it to strong shocks. When the release button is pressed and the D.C.P is unlocked, the car's vibrations may cause it to fall. To prevent damage to the D.C.P, always store it in a protective case after detaching it. The rear connector that connects the main unit and the D.C.P is an extremely important part. Be careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc.

Note:

If the D.C.P is dirty, wipe off the dirt with soft, dry cloth only. And use a cotton swab soaked in isopropyl

Socket

alcohol to clean the socket on the back of the D.C.P.

IMPORTANT

These 2 screws are used to prevent damage to the CD mechanism during transportation Please make sure to remove the 2 screws before installing the unit into the vehicle. DO NOT insert a CD into the unit before removing the 2 screws.

3. ELECTRICAL CONNECTION

a. Make sure your car battery is a 12 volt (6 filler caps) negative ground system (if not, a

converter will be necessary).

b. Before starting wiring connections, disconnect the power supply by removing the fuse from

the fuse box. c. Connect the power wire to one of the extra terminals of the fuse box. d. Connect the black ground wire to a metal part of the car. It is important to make good

contact. e. Make other wiring connections as shown. f. If your car does not have ISO connector, you can purchase it from car accessory shops.

Notes: INCORRECT WIRING OR OPERATION WILL VOID THE WARRANTY OF THIS UNIT.

(CAR UNIT BACK SIDE)

FUSE

RESET BUTTON

The RESET button is located on the main unit (as shown on the diagram). To press it vertically with a ballpoint pen or metal object to activate it. The reset button should be activated for the following reasons:

Initial installation of the unit when all wiring is completed. All the function buttons do not operate. Error symbol on the display.

Note: If you press the RESET button, and the unit still cannot function normally, please use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the control panel.

Fuse Replacement:

To replace the fuse, pull out the blown fuse from the socket. Insert a new one with same rating

BAND/

PANEL

RELEASE

BUTTON

POWER

BUTTON

MUTE

BUTTON

MODE

BUTTON

LOUDNESS/

APL/NTSC

BUTTON

INFRARED

REMOTE SENSOR

ENCODER

VOLUME

DSP/

LEFT/

RIGHT

BUTTON

KNOB

AMS/

PLAY/PAUSE

BUTTON

FUNCTION

SELECT BUTTON

DISPLAY BUTTON

BUTTON

TUNING /

SEEK

UP/DOWN

NEXT/BACK

BUTTON

LOC

SCAN

BUTTON

EJECT

BUTTON

FM MONO /

STEREO BUTTON

+ 20 hidden pages