Boss Audio 822UA-1 User Manual
MP3-Compatible Double-Din In Dash CD Receiver
with USB and SD Memory Card Ports
and Front Panel AUX Input
LOCATION OF CONTROLS
PANEL
RELEASE
BUTTON
POWER
BUTTON
PRESET MEMORY BUTTONS
CD
SLOT
(M1-M6)
MODE
BUTTON
MONO
BUTTON
EJECT
BUTTON
SCAN
BUTTON
CD
PAUSE
BUTTON
ENCODER
VOLUME
KNOB
FUNCTION
SELECT
BUTTON
POWER BUTTON
MP3/AMS BUTTON
TUNING / SEEK / CD TRACK UP / DOWN BUTTON
BAND / LOUDNESS / MP3 ENTER BUTTON
VOLUME UP / DOWN BUTTONS
CD PAUSE BUTTON
CD SHUFFLE BUTTON
LOCAL/DX BUTTON
FM STEREO / MONO BUTTON
DSP
BUTTON
CD
SCAN
BUTTON
MUTE
BUTTON
CD
REPEAT
BUTTON
DISPLAY/
ID3 TAG
INFORMATION
BUTTON
CD
SHUFFLE
BUTTON
BAND/
AMS/MP3
MENU
BUTTON
DIRECTORY
UP/ DOWN
LOUDNESS/
MP3 ENTER
LOCAL
BUTTON
BUTTON
TUNING / SEEK /
TRACK / MP3 FILES SEARCH
UP/DOWN BUTTON
DSP BUTTON
MODE BUTTON
DISPLAY/ ID3 TAG INFORMATION BUTTON
FUNCTION SELECT BUTTON
CD SCAN BUTTON
REPEAT BUTTON
PRESET MEMORY BUTTONS
DIR ECTOR Y UP/DO WN BUTT ONS
SCAN BUTTON
REMOTE CONTROL
E - 1
HANDLING COMPACT DISCS
MOISTURE CONDENSATION
On a rainy day or in a very damp area, moisture may condense on the lenses inside the unit.
Should this occur, the unit will not operate properly. In such a case, remove the disc and wait
for about an hour until the moisture has evaporated.
NOTES ON CDs
1.
A dirty or defective disc may cause sound
dropouts while playing. To enjoy optimum
sound, handle the disc as follows.
Handle the disc by its edge. To keep the
disc clean, do not touch the surface (P.1).
Do not stick paper or tape on the disc (P.2).
2.
Do not expose the discs to direct sunlight or
3.
heat sources such as hot air-ducts, or leave
them in a car parked in direct sunlight where
there can be a considerable rise in
temperature inside the car (P.3).
Before playing, clean the discs with an
4.
optional cleaning cloth. Wipe each disc from
the centre out (P.4).
P. 1
P. 2
P. 3
NOTES ON DISCS
If you use the discs explained below, the
sticky residue can cause the CD to stop
spinning and may cause malfunction or
ruin your discs.
Do not use second-hand or rental CDs that
have a sticky residue on the surface (for
example, from peeled-off stickers or from
ink, or glue leaking from under the
stickers).
There are paste residue.
Ink is sticky (P.5).
P. 5
Do not use rental CDs with old labels that
are beginning to peel off.
Stickers that are beginning
to peel away, leaving a
sticky residue (P.6).
P. 6
Do not use your CDs with labels or
stickers attached.
Labels are attached (P.7).
P. 7
Do Not Use Special Shape CDs
Be sure to use round shape CDs only for
this unit and do not use any special shape
CDs. Use of special shape CDs may
cause the unit to malfunction.(P.8).
*******
*******
*******
*******
**************
*******
*******
*******
****
*******
*******
*******
*******
*******
P. 4
Do not use solvents such as benzine,
5.
thinner,commercially available cleaners, or
antistatic spray intended for analog discs.
P. 8
Be sure to use CDs with disc mark
CD-Rs and CD-RWs which have not
undergone finalization processing cannot
be played. (For more information on
finalization processing, refer to the manual
for your CD-R/CD-RW writing software or
CD-R/CD-RW recorder.) Additionally,
depending on the recording status, it may
prove impossible to play certain CDs
record on CD-R or CD-RW.
E - 2
INSTALLATION
Before finally installing the unit, connect the wiring temporarily and make sure it is all
connected up properly and the unit and system work properly.
Use only the parts included with the unit to ensure proper installation. The use of
unauthorized parts can cause malfunctions.
Consult with your nearest dealer if installation requires the drilling of holes or other
modifications of the vehicle.
Install the unit where it does not get in the driver's way and cannot injure the passenger if
there is a sudden stop, like an emergency stop.I
If installation angle exceeds 30° from horizontal, the unit might not give its optimum
performance.
Avoid installing the unit where it would be subject to high temperature, such as from direct
sunlight, or from hot air, from heater, or where it would be subject to dust dirt or excessive
vibration.
Be sure to remove the front panel before installing the unit.
DIN FRONT/REAR-MOUNT
This unit can be property installed either from “Front” (conventional DIN Front-mount) or
“Rear”(DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit
chassis). For details, refer to the following illustrated installation methods A and B.
DIN FRONT-MOUNT (Method A)
Installation the unit
1
178
2
1. Dashboard
2. Screw
30°
ANTENNA JACK
FRONT LINE OUT LEFT
FRONT LINE OUT RIGHT
REAR LINE OUT LEFT
REAR LINE OUT RIGHT
100
1
7
4
2
3
6
5
1. Dashboard
2. Nut (5mm)
3. Spring washer
4. Screw (5x15mm)
5. Screw
6. Support Strap
Be sure to use the support strap to secure the
back of the unit in place. The strap can be bent by
hand to the desired angle.
7. Plain washer
Trim Plate Installation:
Push the trim plate against the chassis until it is fitted.
You must do this before you install the front panel, otherwise it can't be attached.
E - 3
Loading...