Bosch HBL33, HBL8750, HBL34, HBL54, BL54 User Manual

...
0 (0)

Installation Manual

Guide d’installation

Manual de instalación

Built-In Ovens

Models: HBL33, HBN33, HBL34, HBN34, HBL35, HBN35, HBL54, HBN54,

HBL56, HBN56, HBL57, HBL8550, HBL8650, HBL8750

Table of Contents

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1

Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Before you Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Tools and Parts Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Parts Included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

27” Appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

30” Appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Removing Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

For Convection Microwave Combination Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Preparing Oven . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Electrical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Oven Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Testing Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Before Calling Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

This Bosch Appliance is made by

BSH Home Appliances Corporation

5551 McFadden Ave.

Huntington Beach, CA 92649

Questions?

1-800-944-2904

www.boschappliances.com

We look forward to hearing from you!

Safety

mImportant Safety Instructions

READ AND SAVE THESE INSTRUCTIONS

 

WARNING:

 

If the information in this manual is not followed exactly, fire or shock may result

 

causing property damage or personal injury.

 

WARNING:

 

Do not repair or replace any part of the appliance unless specifically recommended

 

in the manuals. Improper installation, service or maintenance can cause injury or

 

property damage. Refer to this manual for guidance. All other servicing should be

 

done by a qualified technician.

Appliance Handling Safety

Do not lift appliance by door handle. Remove the door for easier handling and

 

installation. See instructions in Use and Care Manual.

 

Unit is heavy and requires at least two people or proper equipment to move.

 

Hidden surfaces may have sharp edges. Use caution when reaching behind or

 

under appliance.

Safety Codes and Standards

This appliance complies with one or more of the following Standards:

 

• UL 858, The Standard for the Safety of Household Electric Ranges

 

• UL 923, The Standard for the Safety of Microwave Cooking Appliances

 

• UL 507, The Standard for the Safety of Electric Fans

 

• ANSI Z21.1, The American National Standard for Household Cooking Gas

 

Appliances

 

• CAN/CSA-C22.2 No. 113-M1984 Fans and Ventilators

 

• CAN/CSA-C22.2 No. 61-M89 Household Cooking Ranges

 

It is the responsibility of the owner and the installer to determine if additional

 

requirements and/or standards apply to specific installations.

Electric Safety

Before you plug in an electrical cord, be sure all controls are in the OFF position.

 

If required by the National Electrical Code (or Canadian Electrical Code), this

 

appliance must be installed on a separate branch circuit.

 

Installer - show the owner the location of the circuit breaker or fuse. Mark it for easy

 

reference.

 

Important - Save these instructions for the local electrical inspector's use.

 

Before installing, turn power OFF at the service panel. Lock service panel to prevent

 

power from being turned ON accidentally.

 

Refer to data plate for more information. See "Data Plate" under "Service" for data

 

plate location.

English 1

mImportant Safety Instructions

READ AND SAVE THESE INSTRUCTIONS

 

Be sure your appliance is properly installed and grounded by a qualified technician.

 

Installation, electrical connections and grounding must comply with all applicable

 

codes.

Related Equipment Safety

Remove all tape and packaging before using the appliance. Destroy the packaging

 

after unpacking the appliance. Never allow children to play with packaging material.

 

Never modify or alter the construction of the appliance. For example, do not remove

 

leveling legs, panels, wire covers or anti-tip brackets/screws.

Transport

To avoid damage to the oven vent, use the transport method shown in the picture

 

below.

English 2

Preparation

Before you Begin

Tools and Parts Needed

Parts Included

Phillips head screwdriver

Measuring tape

Drill with bit (1/8")

Phillips head screws (6)

27” Appliances

General Information

Power Requirements

The outlet must be properly grounded in accordance with all applicable codes.

Dimensions for 27” Wall-Mounted Units

251/2"

(648mm)

24" (610mm)

263/4"

 

281/4"

(680mm)

2413/16"

(718mm)

 

 

 

(630mm)

 

291/16"

 

27"

(686mm)

(738mm)

 

min. 43/4" (121mm)

 

 

 

 

max. 313/8" (797mm)

237/8" (606mm)

22" (559mm)

Single Oven 27”

It is good practice, when oven is installed at the end of a cabinet run, adjacent to a perpendicular wall or cabinet door, to allow at least 1/4” space between the side of the oven and the wall/door.

For oven support, install 2x4’s extending front to back flush with the bottom and the side of the opening. The supporting base must be well secured to the floor/cabinet and level.

Note: The conduit box must be installed either above or below the unit. If the conduit box is installed below the unit, a 2” diameter hole or space is required between the back wall and the right rear of the 2x4 supports.

The cabinet base must be flat and capable of supporting a weight of at least 210 lbs (95 kg).

English 3

513/4"

(1314mm)

50" (1270mm)

251/2"

(648mm)

24" (610mm)

263/4"

(680mm)

2413/16"

(630mm)

511/8"

(1299mm)

493/4"

(1264mm)

93/4"

(248mm)

237/8" (606mm)

22" (559mm)

251/2"

(648mm)

24" (610mm)

263/4"

(680mm)

2413/16"

(630mm)

491/2"

(1257mm)

483/8"

(1229mm)

191/2"

(500mm)

237/8" (606mm)

22" (559mm)

Double Oven 27”

It is good practice, when oven is installed at the end of a cabinet run, adjacent to a perpendicular wall or cabinet door, to allow at least 1/4” space between the side of the oven and the wall/door.

For oven support, install 2x4’s extending front to back flush with the bottom and the side of the opening. The supporting base must be well secured to the floor/cabinet and level.

Note: The conduit box must be located above the unit to facilitate connecting and servicing.

The cabinet base must be flat and capable of supporting a weight of at least 355 lbs (161 kg).

Combo Oven with Microwave 27”

It is good practice, when oven is installed at the end of a cabinet run, adjacent to a perpendicular wall or cabinet door, to allow at least 1/4” space between the side of the oven and the wall/door.

For oven support, install 2x4’s extending front to back flush with the bottom and the side of the opening. The supporting base must be well secured to the floor/cabinet and level.

Note: The conduit box must be located above the unit to facilitate connecting and servicing.

The cabinet base must be flat and capable of supporting a weight of at least 330 lbs (150 kg).

English 4

251/2"

(648mm) 24"

(610mm)

263/4"

(680mm)

2413/16"

(630mm)

603/4"

(1543mm)

613/8"

595/8"

(1559mm)

(1514mm)

 

93/4"

(248mm)

237/8" (606mm)

22" (559mm)

Combo Oven with Microwave and Warming Drawer 27”

It is good practice, when oven is installed at the end of a cabinet run, adjacent to a perpendicular wall or cabinet door, to allow at least 1/4” space between the side of the oven and the wall/door.

For oven support, install 2x4’s extending front to back flush with the bottom and the side of the opening. The supporting base must be well secured to the floor/cabinet and level.

Note: The conduit box must be located above the unit to facilitate connecting and servicing.

The cabinet base must be flat and capable of supporting a weight of at least 370 lbs (168 kg).

English 5

27” Under-the-counter units

 

161/2"

 

 

 

24"

(419mm)

 

 

 

 

(610mm)

 

 

 

 

 

36"

 

 

 

(915mm)

281/4"

min. 33/4"

20"

(95mm)

(718mm)

(508mm)

263/4"

251/2"

 

 

(680mm)

 

 

(648mm)

 

 

2413/16"

4"

 

(630mm)

 

(102mm)

 

 

 

 

 

27"

 

 

291/16"

(686mm)

 

 

(738mm)

237/8" (606mm)

22" (559mm)

English 6

30” Appliances

Dimensions for 30” Wall-Mounted Units

281/2"

(724mm)

24" (610mm)

293/4"

 

281/4"

(755mm)

2713/16"

(718mm)

 

 

 

(706mm)

 

291/16"

(738mm)

513/4"

(1314mm)

27" (686mm)

min. 43/4" (121mm) max. 313/8" (797mm)

237/8" (606mm)

22" (559mm)

281/2"

(724mm)

24" (610mm)

293/4"

(755mm)

2713/16"

(706mm)

511/8"

(1299mm)

493/4"

(1264mm)

93/4"

(248mm)

237/8" (606mm)

22" (559mm)

Single Oven 30”

It is good practice, when oven is installed at the end of a cabinet run, adjacent to a perpendicular wall or cabinet door, to allow at least 1/4” space between the side of the oven and the wall/door.

For oven support, install 2x4’s extending front to back flush with the bottom and the side of the opening. The supporting base must be well secured to the floor/cabinet and level.

Note: The conduit box must be installed either above or below the unit. If the conduit box is installed below the unit, a 2” diameter hole or space is required between the back wall and the right rear of the 2x4 supports.

The cabinet base must be flat and capable of supporting a weight of at least 190 lbs (86 kg).

Double Oven 30”

It is good practice, when oven is installed at the end of a cabinet run, adjacent to a perpendicular wall or cabinet door, to allow at least 1/4” space between the side of the oven and the wall/door.

For oven support, install 2x4’s extending front to back flush with the bottom and the side of the opening. The supporting base must be well secured to the floor/cabinet and level.

Note: The conduit box must be located above the unit to facilitate connecting and servicing.

The cabinet base must be flat and capable of supporting a weight of at least 330 lbs (150 kg).

English 7

50" (1270mm)

613/8"

(1559mm)

281/2"

(724mm)

24" (610mm)

293/4"

(755mm)

2713/16"

(706mm)

491/2"

(1257mm)

483/8"

(1229mm)

191/2"

(500mm)

237/8" (606mm)

22" (559mm)

281/2"

(724mm) 24"

(610mm)

293/4"

(755mm)

2713/16"

(706mm)

603/4"

(1543mm)

595/8"

(1514mm)

93/4"

(248mm)

237/8" (606mm)

22" (559mm)

Combo Oven with Microwave 30”

It is good practice, when oven is installed at the end of a cabinet run, adjacent to a perpendicular wall or cabinet door, to allow at least 1/4” space between the side of the oven and the wall/door.

For oven support, install 2x4’s extending front to back flush with the bottom and the side of the opening. The supporting base must be well secured to the floor/cabinet and level.

Note: The conduit box must be located above the unit to facilitate connecting and servicing.

The cabinet base must be flat and capable of supporting a weight of at least 290 lbs (132 kg).

Combo Oven with Microwave and Warming Drawer 30”

It is good practice, when oven is installed at the end of a cabinet run, adjacent to a perpendicular wall or cabinet door, to allow at least 1/4” space between the side of the oven and the wall/door.

For oven support, install 2x4’s extending front to back flush with the bottom and the side of the opening. The supporting base must be well secured to the floor/cabinet and level.

Note: The conduit box must be located above the unit to facilitate connecting and servicing.

The cabinet base must be flat and capable of supporting a weight of at least 310 lbs (141 kg).

English 8

281/2"

(724mm) 24"

(610mm)

293/4"

(755mm)

 

2713/16"

40"

 

(706mm)

(1016mm)

407/16"

381/8"

 

(968mm)

(1027mm)

 

 

 

 

93/4"

 

 

(248mm)

237/8" (606mm)

22" (559mm)

Combo Oven with Warming Drawer 30”

It is good practice, when oven is installed at the end of a cabinet run, adjacent to a perpendicular wall or cabinet door, to allow at least 1/4” space between the side of the oven and the wall/door.

For oven support, install 2x4’s extending front to back flush with the bottom and the side of the opening. The supporting base must be well secured to the floor/cabinet and level.

Note: The conduit box must be located above the unit to facilitate connecting and servicing.

The cabinet base must be flat and capable of supporting a weight of at least 290 lbs (132 kg).

English 9

30” Under-the-counter-Units

 

 

 

 

161/2"

 

 

 

24"

(419mm)

 

 

 

 

 

 

 

 

(610mm)

 

 

 

 

 

 

 

36"

 

 

 

 

 

(915mm)

 

 

281/4"

min. 33/4"

20"

 

 

(95mm)

 

 

(718mm)

(508mm)

 

293/4"

 

281/2"

 

 

 

(755mm)

 

 

 

 

2713/16"

(724mm)

 

 

 

 

4"

 

 

 

 

 

 

 

(706mm)

 

 

 

(102mm)

 

 

 

 

 

 

 

 

 

27"

 

 

291/16"

 

 

(686mm)

 

 

(738mm)

237/8" (606mm)

22" (559mm)

English 10

Bosch HBL33, HBL8750, HBL34, HBL54, BL54 User Manual

Removing Packaging

Cut foil wrap in the area of corner posts.

Remove foil completely.

Remove top cardboard.

Remove all top and side cardboard and Styrofoam braces.

Place oven in front of cabinets where it is to be installed.

Unscrew unit from Left and Right Brackets as show in “Left and Right Packaging Bracket Removal.”

Left and Right Packaging Bracket Removal

Note:

For Convection

Microwave Combination

Units

Bracket remains in packaging base. Unit should stay in packaging base plate until ready to be lifted into cabinet cutout.

Remove 2 rear support Convection Microwave Shipping Brackets prior to installation as shown in “Convection Microwave Shipping Bracket Removal.”

Convection Microwave Shipping Bracket Removal (for Convection Microwave Combination Units Only)

Preparing Oven

Place oven in front of cabinets where it is to be installed. Rest it on a jack or other sturdy support so that it is in line with the cabinet cutout.

English 11

Installation

Electrical Installation

All model ovens on the front cover are dual rated, designed to be connected to either 208/240V AC, 60 Hz, 4 wire, single-phase power supply.

Model

Circuit Required

 

 

 

 

208V, 60 Hz

 

240V, 60 Hz

 

 

 

 

HBN33, HBL33

25 AMP

 

30 AMP

 

 

 

 

HBN34, HBL34,

30 AMP

 

30 AMP

HBN54, HBL54

 

 

 

HBL85

 

 

 

 

 

 

HBN35, HBL35,

40 or 50 Amp circuit. Refer to local electrical codes

HBN56, HBL56, HBL57,

for de-rating requirements.

 

HBL8650, HBL8750

 

 

 

 

 

 

 

The electrical supply should be a 4-wire single-phase AC. Install a suitable conduit box (not furnished).

Important: Local Codes may vary, installation, electrical connections and grounding must comply with all applicable local codes.

If local codes permit grounding through the electrical supply neutral, connect both the white neutral wire and the bare ground wire from the oven to the white neutral electrical supply wire.

English 12

Electrical Connection

The four-wire connection is preferred, but where local codes permit, the three wire

 

connection is also acceptable.

 

Four-wire Connection

Connect the red oven wire to the red electrical supply wire (hot wire).

Connect the black oven wire to the black electrical supply wire (hot wire).

Connect the white neutral oven wire to the white neutral (not bare ground) electrical supply wire.

Connect the bare ground oven wire to the bare ground electrical supply wire.

Three-wire Connection

Connect red wire from oven to red wire injunction box.

Connect black wire from oven to black wire in junction box.

Connect both green ground wire and white wire from oven to white (or gray) neutral wire in junction box.

The conduit cable, where connected at the oven, swivels. Rotate conduit cable upward (or downward) and direct through hole prepared in cabinet to attach to J- Box.

To maintain serviceability, the flex conduit must not be shortened and should be routed to permit temporary removal of the oven.

English 13

Oven Installation

 

Note: Before installing the oven be sure to verify the cabinet dimensions and electrical

 

connections.

Removing the Oven Door

For ease of installation, some oven doors may be removed to reduce the weight of

 

the oven by 30 lbs (14 kg) per door, before installing into the cabinet. See “To

 

remove the oven door.”

m CAUTION:

When removing the door:

Make sure oven is cool and power to the oven has been turned off before removing the door. Failure to do so could result in electrical shock or burns.

The oven door is heavy and fragile. Use both hands to remove the oven door. The door front is glass. Handle carefully to avoid breaking.

Grasp only the sides of the oven door. Do not grasp the handle as it may swing in your hand and cause damage or injury.

Failure to grasp the oven door firmly and properly could result in personal injury or product damage.

To avoid injury from hinge bracket snapping closed, be sure that both levers are securely in place before removing the door. Also, do not force door open or closed - the hinge could be damaged and injury could result.

To remove the oven door:

1. Be sure to read the above CAUTION before attempting to remove the door.
2. Open the door completely.
3. Flip levers on hinges toward you.
4. Close door carefully until it stops. It will be about half way closed.
5. Holding the door firmly on both sides using both hands, pull the door up and out of the hinge slots. Hold firmly; the door is heavy.
6. Place the door in a convenient and stable location for cleaning.

English 14

Installing the Oven
1. Lift or slide unit into cabinet cutout. Do not lift appliance by door handle.

 

2. Push straight in until oven trim is flush with cabinet wall, being careful not to

 

 

crimp flexible conduit between oven and cabinet back wall. The oven should be

 

 

straight and level, not crooked.

 

 

 

3. Install supplied screws through tap holes in trim. (2 screws for single ovens, 4

 

 

screws for double/combo ovens)

 

 

 

To replace the oven door:

 

 

 

 

 

 

 

 

 

 

 

 

 

1.

Holding the door firmly in both hands,

 

 

 

 

 

 

place hinges in hinge slots.

 

 

 

 

 

2.

Open door all the way to expose

 

 

 

 

 

 

hinges and slots.

 

 

 

 

 

3.

Push lever down and away from you

 

 

 

 

 

 

until flush with the bracket.

 

 

 

 

 

4.

Close and open door slowly to be sure

 

 

 

 

 

 

it is correctly and securely in place.

 

 

 

 

 

 

Door must be straight, not crooked.

 

 

 

 

 

 

 

 

Testing Operation

1.Turn on power at the breaker.

2.Check power at junction box using a volt meter.

For 240 V installation, the reading between the red and black wires (line to line) should be 220 to 240 volts.

For 208 V installation, the reading between the red and black wires (line to line) should be 190 to 208 volts.

3.Test the oven mode.

Select the BAKE mode. See the Use and Care Manual for detailed operation instructions.

4.Verify that the oven light comes on and the oven begins to preheat.
5.Test the door lock.

Set the SELF CLEAN mode. Confirm that the door locks when the lock icon appears in the display.

6.If installing a double oven, test the second oven as well.
7.If any of the tests do not result as explained above, contact Thermador service for assistance. Otherwise, the installation is complete at this time.

English 15

Loading...
+ 39 hidden pages