Loading...
FMR-7036
Installation Instructions
EN Fire Annunciator Keypad
FMR-7036 | Fire Annunciator Keypad | Contents |
|
|
Contents |
|
|
Contents ........................................................................... |
2 |
|
1.0 |
Notice ................................................................. |
3 |
2.0 |
Device Description.......................................... |
3 |
3.0 |
Installing the Reference Card....................... |
3 |
4.0 |
Mounting the FMR-7036 ................................. |
3 |
4.1 |
Surface Mounting............................................... |
3 |
4.2 |
Electrical Box Mounting.................................... |
3 |
5.0 |
Setting the FMR-7036 Address ...................... |
4 |
6.0 |
Wiring the FMR-7036 ...................................... |
4 |
7.0 |
FMR-7036 Programming ................................ |
5 |
7.1 |
FPD-7024 Local Programming ......................... |
5 |
7.2 |
FPD-7024 Remote Programming ..................... |
5 |
8.0 |
FMR-7036 Operation....................................... |
5 |
8.1 |
Silence ................................................................. |
5 |
8.2 |
Reset .................................................................... |
6 |
8.3 |
Scrolling Buttons ................................................ |
6 |
8.4 |
Keylock Switch ................................................... |
6 |
8.5 |
Display................................................................. |
6 |
8.6 |
Reset Switch........................................................ |
6 |
9.0 |
Troubleshooting............................................... |
7 |
10.0 |
Specifications .................................................... |
7 |
Figures |
|
|
Figure 1: FMR-7036 Fire Annunciator Keypad ....... |
3 |
|
Figure 2: Reference Card Installation ....................... |
3 |
|
Figure 3: Mounting Hole Locations .......................... |
4 |
|
Figure 4: Inside View of FMR-7036 Keypad ........... |
4 |
|
Figure 5: FMR-7036 Address Jumper Settings......... |
4 |
|
Figure 6: FMR-7036 Wire Connections.................... |
5 |
|
Tables |
|
|
Table 1: |
FMR-7036 LED Functions......................... |
6 |
Table 2: |
FMR-7036 Troubleshooting Tips .............. |
7 |
Table 3: |
FMR-7036 Specifications............................ |
7 |
2 |
Bosch Security Systems, Inc. | 9/08 | F01U010584-01 |
FMR-7036 | Fire Annunciator Keypad | |
1.0 |
Notice |
|
|
|
1.0 Notice
These instructions cover the installation of the Bosch Security Systems, Inc. FMR-7036 Fire Annunciator Keypad in a fire system supervised by a Bosch FPD7024 Fire Alarm Control/Communicator.
Install, test and maintain the FMR-7036 according to these instructions, NFPA 72, local codes, and the authority having jurisdiction. Failure to follow these instructions may result in failure of the device to operate properly. Bosch Security Systems, Inc. is not responsible for improperly installed, tested or maintained devices.
NFPA 72 requires a complete system-wide functional test be performed following any modifications, repair, upgrades, or adjustments made to the system’s components, hardware, wiring, programming, and software/firmware.
These instructions contain procedures to follow in order to avoid personal injury and damage to equipment.
2.0 Device Description
The FMR-7036 is a four-wire LCD annunciator keypad for the FPD-7024 Fire Alarm Control/Communicator. It may be surface mounted to a standard three-gang box or with the provided mounting backplate.
Figure 1: |
FMR-7036 Fire Annunciator Keypad |
|
|
SILENCED |
TROUBLE |
|
ALARM |
SUPERVISORY |
|
|
FIRE SYSTEM ANNUNCIATOR |
|
|
LOCK |
|
|
UNLOCK |
3.0 Installing the Reference
Card
A quick-reference card is provided and needs to be installed in the receiving slot indicated in Figure 2. The slot is located behind the mounting base holding the circuit board.
Install the reference card before securing the keypad.
Figure 2: Reference Card Installation
FMR-7036 Reference Card |
2 |
|
|
1 |
|
Slide reference guide between keypad holding tabs.
1 - Reference Card Stopper Tabs
2 - Holding Tabs
4.0 Mounting the FMR-7036
The keypad should be mounted no higher than shoulder height of the shortest person using the system.
Remove the keypad’s cover.
Insert a small flathead screwdriver in each slot at the bottom of the base. Press up, and pull the cover off.
4.1Surface Mounting
Use the base as a template to mark the location of the mounting holes (refer to Figure 3 on page 4 for mounting hole location).
Provide an opening in the mounting surface for the wiring.
Pre-start the mounting screws.
Do not secure the base at this point.
4.2Electrical Box Mounting
Refer to Figure 3 on page 4 for the location of the mounting holes.
Bosch Security Systems, Inc. | 9/08 | F01U010584-01 |
3 |
Loading...