Car Radio SD USB MP3 WMA
Brisbane SD48
Victoria SD48
7 648 000 310
7 648 001 310
Bedienungsund Einbauanleitung Operating and installation instructions Mode d’emploi et de montage Istruzioni d’uso e di installazione
Gebruiksaanwijzing en inbouwhandleiding Bruksoch monteringsanvisning Instrucciones de manejo e instalación Instruções de serviço e de montagem Betjeningsog monteringsvejledning Instrukcja obsługi i montażowa
Návod k obsluze a k montáži Návod na obsluhu a inštaláciu
Инструкция по эксплуатации и установке
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
9 |
14 |
13 |
12 |
11 |
10 |
2
Controls
1
button for removing the control panel (release panel)
2 Arrow buttons
3 SRC button for source selection between Radio, SD, USB and CD changer or AUX and FRONT-AUX (if connected).
4Button to switch the device on/off and operate the volume mute feature.
5BND•TS button
Short press: Selects the FM memory banks and the MW and LW wavebands. Long press: Starts the Travelstore function.
6 Volume control
7 LCD display
8 Keys 1 - 5
9 Slot for SD/MMC cards
:Front AUX-IN socket for connecting external audio sources (e.g. portable CD players).
; DIS button
< ESC button
=TRAF•RDS button
Short press: Switches traffic information standby on/off.
Long press: Switches convenient RDS function on/off.
>MENU button
Short press: Calls up the menus for the settings. Confirming menu settings. Long press: Starts the scan function.
40
Contents
About these instructions .................. |
43 |
Symbols used................................ |
43 |
Use as directed.............................. |
43 |
Declaration of conformity................ |
43 |
For your safety ................................ |
44 |
If you are installing device yourself.... |
44 |
Observe the following!.................... |
44 |
Cleaning instructions...................... |
44 |
Disposal note ................................ |
44 |
Scope of delivery ............................. |
45 |
Optional equipment |
|
(not part of the scope of delivery) .... |
45 |
Warranty......................................... |
46 |
Service ........................................... |
46 |
Detachable control panel ................. |
47 |
Theft protection............................. |
47 |
Detaching the control panel............. |
47 |
Attaching the control panel.............. |
47 |
Switching on/off.............................. |
48 |
Switching on/off using button 4 .... |
48 |
Switching on/off via vehicle ignition ... |
48 |
Switching off with detachable |
|
control panel................................. |
48 |
Timeout function ............................. |
48 |
Adjusting the volume ....................... |
49 |
Setting the power-on volume ........... |
49 |
Quickly reducing the volume (MUTE).... |
49 |
Switching the confirmation |
|
beep on/off (BEEP)........................ |
50 |
Muting during telephone mode ........ |
50 |
Telephone Audio/Navigation Audio ... |
50 |
Radio mode ..................................... |
51 |
Adjusting the tuner......................... |
51 |
Switching to radio mode ................. |
51 |
Convenient RDS functions............... |
52 |
Selecting the waveband/ |
|
memory bank ................................ |
52 |
Tuning into a station ....................... |
53 |
Adjusting the sensitivity of |
|
the station seek tuning (SENS) ........ |
53 |
Storing stations ............................. |
53 |
Storing stations automatically |
|
(Travelstore) ................................. |
54 |
Listening to stored stations ............. |
54 |
Scanning receivable stations (SCAN) ... |
54 |
Setting the scanning time |
|
(SCAN TIME)................................. |
54 |
Programme type (PTY) .................. |
55 |
Configuring the display ................... |
56 |
Traffic information........................... |
56 |
Switching traffic information |
|
priority on/off ............................... |
56 |
Skipping a traffic announcement...... |
57 |
Setting the volume for traffic |
|
announcements............................. |
57 |
MP3/WMA mode ............................. |
58 |
Preparation of an MP3/WMA |
|
data carrier ................................... |
58 |
Switching to MP3 mode .................. |
59 |
Configuring the display ................... |
60 |
Selecting a directory ...................... |
60 |
Selecting tracks............................. |
60 |
Fast searching (audible).................. |
60 |
Repeating individual tracks or |
|
whole directories (REPEAT)............. |
60 |
Random track play (MIX)................. |
61 |
Scanning tracks (SCAN).................. |
61 |
Interrupting playback (PAUSE)......... |
61 |
ENGLISH
41
Contents
CD-changer mode ............................ |
62 |
Switching to CD-changer mode ........ |
62 |
Selecting CDs................................ |
62 |
Selecting tracks............................. |
62 |
Fast searching (audible).................. |
62 |
Configuring the display ................... |
62 |
Repeating individual tracks or |
|
whole CDs (REPEAT) ...................... |
62 |
Random track play (MIX)................. |
63 |
Scanning all tracks on all CDs (SCAN)... |
63 |
Interrupting playback (PAUSE)......... |
63 |
Clock Time ...................................... |
64 |
Displaying the time ........................ |
64 |
Setting the time ............................. |
64 |
Selecting 12/24-hour clock mode .... |
64 |
Displaying the time with device |
|
and ignition switched off................. |
64 |
Sound ............................................. |
65 |
Equalizer ...................................... |
65 |
Setting the left/right volume |
|
distribution (BALANCE).................. |
68 |
Adjusting the front/rear volume |
|
distribution (FADER) ...................... |
68 |
Equalizer presettings (PRESETS) ..... |
68 |
X-BASS ........................................... |
69 |
Adjusting the X-BASS boost............. |
69 |
Adjusting E-XBASS......................... |
70 |
Display............................................ |
71 |
Adjusting the display brightness....... |
71 |
Setting the display illumination |
|
colour .......................................... |
71 |
External audio sources ..................... |
73 |
Rear AUX-IN input .......................... |
73 |
Front AUX-IN socket ....................... |
74 |
Mixing an external audio source with |
|
another audio source (MIX AUX)....... |
74 |
Factory settings (Normset)............... |
75 |
Technical data ................................. |
76 |
Installation instructions ................. |
484 |
42
About these instructions
About these instructions
•These instructions contain important information to easily and safely install and operate the device.
•Read these instructions carefully and completely before using the device.
•Keep the instructions at a location so that they are always accessible to all users.
•Always pass on the device to third parties together with these instructions.
In addition, observe the instructions of the devices used in conjunction with this device.
Use as directed
This device is intended for installation and operation in a vehicle with 12 V vehicle system voltage and must be installed in a DIN slot. Observe the 'performance limits in the technical data. Repairs and installation, if necessary, should be performed by a specialist.
Declaration of conformity
The Blaupunkt GmbH declares that the devices Victoria SD48 and Brisbane SD48 comply with the basic requirements and the other relevant regulations of the directive 89/336/EWG.
ENGLISH
Symbols used
These instructions employ the following symbols:
DANGER!
Warns about injuries
DANGER!
Warns about accidents
DANGER!
Warns about hearing loss
The CE mark confirms the compliance with EU directives.
Identifies a sequencing step
•Identifies a listing
43
For your safety
For your safety
The device was manufactured according to the state of the art and established safety guidelines. Even so, dangers may occur if you do not observe the safety notes in these instructions.
If you are installing device yourself
You may only install the device yourself if you are experienced in installing car sound systems and are very familiar with the electrical system of the vehicle. For this purpose, observe the installation instructions at the end of these instructions.
Observe the following!
DANGER!
Increased risk of injury from connector
In case of an accident, the protruding connector in the front AUX-IN socket may cause injuries. The use of straight plugs or adapters can lead to an increased risk of injury.
•For this reason, we recommend using angled jack plugs, e.g. the Blaupunkt accessories cable (7 607 001 535).
In operation
•Operate the device only if traffic situation permits it! Stop at a suitable location to perform extensive settings.
•Remove or attach the control panel only while the vehicle is standing an.
•To protect your hearing, always listen at a moderate volume. During mute phases (e.g. while the CD changer is changing the CD), changing the volume is not detectable until after this mute phase. Do not increase the volume during this mute phase
•Always listen at a moderate volume so that you can always hear acoustic warning signals (e.g. police).
After operation
•The device is worthless to a thief without the control panel. Always remove the control panel whenever you leave the vehicle.
•Transport the control panel so that it is protected against impacts and the contacts cannot become dirty.
Cleaning instructions
Solvents, cleaning and scouring agents as well as dashboard spray and plastics care product may contain ingredients that will damage the surface of the device. Use only a dry or slightly moistened cloth for cleaning the device.
Disposal note
Do not dispose of your old unit in the household trash!
Use the return and collection systems available to dispose of the old device.
44
Scope of delivery
Scope of delivery
The scope of delivery includes:
1Car sound system
1Support frame
2 Disassembly tools
1Guide pin
1USB connecting cable
1Operating instructions
Optional equipment
(not part of the scope of delivery)
Use only accessories approved by Blaupunkt.
Remote control
The steering wheel and/or handheld remote control allows you to access the most important functions of your car sound system safely and conveniently.
You cannot switch the device on/off using the remote control!
You can find out from your Blaupunkt dealer or on the Internet at www.blaupunkt.com which remote controls can be used with your car sound system.
Bluetooth/USB interface
For Bluetooth applications, such as wireless hands-free calling and Bluetooth streaming, you can connect a Bluetooth interface. The Bluetooth/USB interface provides an additional USB connection.
iPod/USB interface |
|
|
The iPod interface or iPod/USB interface |
|
|
allows connecting the iPod or iPod Mini to |
|
|
the radio device and conveniently control- |
|
|
ling the playback via the radio device. The |
|
|
|
||
iPod/USB interface provides an additional |
ENGLISH |
|
USB connection. |
||
|
||
Amplifier |
|
|
You can use all Blaupunkt and Velocity |
|
|
amplifiers. |
|
|
CD changers |
|
|
You can connect the following Blaupunkt |
|
|
CD changers: |
|
|
CDC A 03, CDC A 08 and IDC A 09. |
|
45
Warranty |
Service |
Warranty
We provide a manufacturer's warranty for products bought within the European Union. For devices purchased outside the European Union, the warranty terms issued by our respective responsible domestic agency are valid.
The warranty terms can be called up under www.blaupunkt.com or requested directly from:
Blaupunkt GmbH
Hotline
Robert-Bosch-Str. 200
D-31139 Hildesheim
Service
In some countries, Blaupunkt offers a repair and pick-up service.
Information about the availability of this service in your country can be found at www.blaupunkt.com.
If you want to take advantage of this service, you may request a pick-up service for your device via the Internet.
46
Detachable control panel
Detachable control panel
Theft protection
The device is equipped with a detachable control panel (flip-release panel) to protect your equipment against theft. The device is worthless to a thief without this control panel.
Protect your device against theft by taking the control panel with you whenever you leave your vehicle. Do not leave the control panel inside your vehicle - not even in a hiding place.
The control panel has been designed to be easy to use.
Notes:
•Never drop the control panel.
•Never expose the control panel to direct sunlight or other heat sources.
•Avoid direct skin contact with the control panel’s electrical contacts. If necessary, clean the contacts with a lint-free cloth moistened with cleaning alcohol.
Detaching the control panel
1
ENGLISH
Press the 
button 1.
The locking mechanism of the control panel is unlocked. The device switches off.
Pull the control panel straight out of the device and to the left.
All the current settings are saved.
Attaching the control panel
Push the control panel into the guides of the device from the left to the right.
Note:
When attaching the control panel, make sure you do not push on the display.
Carefully push on the left side of the control panel until it clicks into place.
47
Switching on/off |
Timeout function |
Switching on/off
There are various ways of switching the device on/off:
Switching on/off using button 4
To switch on the device, press button
4.
To switch off the device, press and hold down button 4 for longer than two seconds.
The device switches off.
Note:
To protect the vehicle battery, the device will switch off automatically after one hour if the ignition is off.
Switching on/off via vehicle ignition
The device will switch on/off simultaneously with the ignition if the device is correctly connected to the vehicle’s ignition and you did not switch the device off and back on by pressing button 4.
Switching off with detachable control panel
Detach the control panel. The device switches off.
Timeout function
The device features a time-out function (time window). For example, if you press the MENU button > and select a menu item, the device switches back after approx. 8 seconds after the last button activation. The settings performed are saved.
48
Adjusting the volume
Adjusting the volume
You can adjust the volume in steps from 0 (off) to 50 (maximum).
To increase the volume,
turn the volume control 6 clockwise. To decrease the volume,
turn the volume control 6 counterclockwise.
Setting the power-on volume
You can set the power-on volume. You can adjust it manually or select the "LAST VOL" setting. If you enable "LAST VOL", the volume which was set the last time you switched off the device is re-enabled.
Press the MENU button >. The display shows "MENU".
Press the 
or 
button 2repeatedly until "ON VOLUME" appears on the display.
Press the 
button 2 to manually adjust the power-on volume and
adjust the power-on volume using the 
or 
buttons 2.
OR:
Press the 
button 2 to select the "LAST VOL" setting.
When you have finished making your changes,
press the MENU button >. To exit the menu,
press the ESC button <.
Note: |
|
|
To protect your hearing, the power-on |
|
|
volume is limited to the value "38" for |
|
|
the setting "LAST VOL". If the "LAST |
|
|
VOL" setting is selected and the vol- |
|
|
ume was set higher than "38" before |
ENGLISH |
|
switch-off, the value "38" will be used |
||
|
||
at switch-on. |
|
Quickly reducing the volume (MUTE)
You can quickly reduce the volume to a preset level (Mute).
Briefly press button 4. "MUTE" appears on the display.
Cancelling mute
To return to your previously set volume level,
briefly press button 4 again.
Adjusting the mute level
You can adjust the mute level.
Press the MENU button >. The display shows "MENU".
Press the 
or 
button 2 repeatedly until "MUTE LVL" appears on the display.
Press the button
2to open the submenu.
"MUTE" and the currently set value are displayed.
Adjust the mute level using the button 
or 
2.
49
Adjusting the volume
When you have finished making your changes,
press the MENU button >. To exit the menu,
press the ESC button <.
Switching the confirmation beep on/off (BEEP)
The system will output a confirmation beep for some functions if you keep a button pressed down for longer than two seconds, for instance, when assigning a radio station to a station preset button. You can switch the beep on or off.
Press the MENU button >. The display shows "MENU".
Press the 
or 
button 2repeatedly until "BEEP ON" or "BEEP OFF" appears on the display.
Press the 
button 2 to call up the submenu.
Switch the beep on or off using the
button 2. "OFF" means beep off, "ON" means beep on.
When you have finished making your changes,
press the MENU button >. To exit the menu,
press the ESC button <.
Muting during telephone mode
If your car sound system is connected with a cell phone or navigation system, the car sound system is muted when a call is incoming or during a voice output of the navigation. The call or the voice output is played back via the loudspeakers of the card sound system. In order for this feature to work, the mobile telephone or navigation system must be connected to the car sound system as described in the installation instructions.
You can find out from your Blaupunkt dealer which navigation systems can be used with your car sound system.
If a call is incoming or a navigation announcement takes place, the display shows "TELEPHONE".
Telephone Audio/Navigation Audio
During a telephone call or a voice output of the navigation, no traffic announcements are switched through.
You can set the volume level at which the telephone calls or navigation announcements are mixed in.
Press the MENU button >. The display shows "MENU".
Press the
or 
button 2repeatedly until "TEL VOL" appears on the display.
Press the 
button 2 to call up the submenu.
"TELVOL" and the currently set value are displayed.
Set the desired volume with the 
or 
button 2.
50
Adjusting the volume |
Radio mode |
When you have finished making your changes,
press the MENU button >. To exit the menu,
press the ESC button <.
Notes:
•If the volume listened to is higher than the set "TEL VOL" value, telephone calls or navigation announcements are played back at the volume listened to.
•Using the volume control 6, you can adjust the volume for telephone calls and navigation announcements directly during the playback.
Radio mode
Adjusting the tuner
To ensure proper functioning of the tuner, the device must be set for the region in
which it is being operated. You can select |
ENGLISH |
|
|
between Europe (EUROPE), America (USA) |
|
and Thailand (THAI). The tuner is factory- |
|
set to the region in which it was sold. If you |
|
experience problems with your radio recep- |
|
tion, please check this setting. |
|
The radio functions described in these operating instructions refer to the tuner setting EUROPE.
Switch off the device by pressing button 4.
Hold the buttons 1 8 and DIS ;
pressed at the same time and switch on the device again with the button 4.
The current setting is displayed. |
|
|
||
Select your tuner region with the |
|
or |
||
|
||||
|
|
button 2. |
|
|
|
|
|
|
|
To save the setting and to exit the menu,
press the MENU button >.
Switching to radio mode
If you are in SD, USB, CD changer or AUXIN mode,
press the BND•TS button 5
or
press the SRC button 3 repeatedly until "TUNER" appears on the display.
51
Radio mode
Convenient RDS functions
This device is equipped with an RDS (Radio Data System) radio receiver. Many FM stations broadcast a signal that not only carries the programme but also additional information such as the station name and programme type (PTY).
The station name appears on the display as soon as the tuner receives it.
The convenient RDS functions AF (Alternative Frequency) and REGIONAL extend your radio’s range of functions.
•AF: If the RDS function is activated, the radio automatically tunes into the best receivable frequency for the station that is currently set.
•REGIONAL: At certain times, some radio stations divide their programme into regional programmes providing different content. You can use the REG function to prevent the car radio from switching to alternative frequencies that are transmitting different programme content.
Note:
REGIONAL must be activated/deactivated (REG ON/OFF) separately in the menu.
Switching the RDS function on/off
If you want to use the RDS functions (AF and REGIONAL),
press and hold down the TRAF•RDS button = for longer than two seconds.
The RDS function is active if RDS appears on the display.
To deactivate,
press and hold down the TRAF•RDS button = for longer than two seconds.
The RDS symbol disappears from the display.
Switching REGIONAL on/off
Press the MENU button >. The display shows "MENU".
Press the 
or 
button 2repeatedly until "REG ON" or "REG OFF" appears on the display.
Press the button 
2to open the submenu.
To switch REGIONAL on/off,
press the 
button 2.
Press the MENU button >. To exit the menu,
press the ESC button <.
Selecting the waveband/memory bank
This device can receive programmes broadcast over the FM frequency range as well as the MW and LW (AM) wavebands. There are three memory banks available for the FM waveband (FM1, FM2 and FMT) and one for each of the MW and LW wavebands.
Five stations can be stored in each memory bank.
To switch between the FM memory banks (FM1, FM2 and FMT) and the MW and LW wavebands,
briefly press the BND•TS button 5.
52
Radio mode
Tuning into a station
There are various ways of tuning into a station:
Automatic station seek tuning
Press the 
or 
button 2.
The radio tunes into the next receivable station.
Tuning into stations manually
You can also tune into stations manually.
Note:
You can only tune into stations manually if the convenient RDS function and RDY are deactivated.
Press the
or 
button 2.
Browsing through broadcasting networks (FM only)
If radio stations provide several programmes, you have the option of browsing through these so-called "broadcasting networks".
Note:
The convenient RDS function and PTY must be activated before you can use this feature.
Press the 
or 
button 2 to switch to the next station on the broadcasting network.
Note:
When using this feature, you will only be able to switch to stations that you have received once before already. To receive the stations, use the Scan or Travelstore function.
Adjusting the sensitivity of the station seek tuning (SENS)
You can choose whether the radio should only tune into stations providing good reception or whether it can also tune into
those with a weak reception. |
ENGLISH |
||||
|
|||||
Press the MENU button >. |
|
||||
The display shows "MENU". |
|
||||
Press the |
|
or |
|
button 2repeatedly |
|
|
|
|
|||
|
|
||||
until "SENS" and the currently set value |
|
||||
appears on the display. |
|
||||
"SENS HI6" means that the tuner is set to the highest sensitivity setting. "SENS LO1" means it is set to the lowest sensitivity setting.
Press the button 
2to open the submenu.
Set the desired sensitivity level using the 
or 
button 2.
When you have finished making your changes,
press the MENU button >. To exit the menu,
press the ESC button <.
Note:
You can set different sensitivity levels for FM and AM (MW/LW).
Storing stations
Storing stations manually
Select the desired memory bank (FM1, FM2, FMT) or one of the wavebands (MW or LW).
Tune into the desired station.
53
Radio mode
Press and hold down one of the station buttons 1 - 5 8 for longer than two seconds to assign the station to that button.
Storing stations automatically (Travelstore)
You can automatically store the five stations offering the strongest reception in the region (only FM). The stations are stored in the FMT memory bank.
Note:
Any stations that were previously stored in this memory bank are deleted in the process.
Press and hold down the BND•TS button 5 for longer than two seconds.
The storing procedure begins. "FM TSTORE" appears on the display. After the process has completed, the radio will play the station that is stored in memory location 1 of the FMT memory bank.
Listening to stored stations
Select the memory bank or waveband.
Press the station button 1 - 5 8 of the desired station.
Scanning receivable stations (SCAN)
You can use the scan function to play all the receivable stations briefly. You can set the scanning time from 5 to 30 seconds in the menu (in increments of 5 seconds).
Starting SCAN
Press and hold down the MENU button > for longer than two seconds.
Scanning begins. "SCAN" and the station name or the frequency appear intermittently on the display.
Cancelling the SCAN and continuing to listen to a station
Press the MENU button >.
Scanning stops and the radio continues playing the station that it tuned into last.
Setting the scanning time (SCAN TIME)
Press the MENU button >. The display shows "MENU".
Press the 
or 
button 2repeatedly until "SCAN TIME" appears on the display.
Press the button 
2to open the submenu.
"SCAN" and the currently set value are displayed.
Set the desired scan time using the 
or 
button 2.
When you have finished making your changes,
press the MENU button >. To exit the menu,
press the ESC button <.
Note:
The adjusted scan time also applies to scan processes in MP3/WMA mode.
54
Loading...