Black & Decker 90558474, V-2 Million, SL302B User Manual

0 (0)
Black & Decker 90558474, V-2 Million, SL302B User Manual

90558474 SL302B.qxp:SL302B ManualENSPFR 073008 11/25/09 1:20 PM Page 24

FICHE TECHNIQUE

Ampoule du projecteur :

12 volts, série H3, ampoule à filament double de 55 W et 35 W

Pile :

au plomb scellée, sans entretien, de 12 volts, 3 ampères-heures

Chargeur inclus à CA :

homologué UL, classe 2, courant continu de 12 volts (300 mA)

Fusible de la fiche de courant continu :

2 A, 250 V

Imported by / Importé par Black & Decker Canada Inc. 100 Central Ave.

Brockville (Ontario) K6V 5W6

V-2 MILLION POWER SERIES

SPOTLIGHT

INSTRUCTION MANUAL

Voir la rubrique “Outils électriques”

des Pages Jaunes pour le service et les ventes.

Catalog Number SL302B

Thank you for choosing Black & Decker! Go to www.BlackandDecker.com/NewOwner to register your new product.

PLEASE READ BEFORE RETURNING THIS

PRODUCT FOR ANY REASON:

If you have a question or experience a problem with your Black & Decker purchase, go to

HTTP://WWW.BLACKANDDECKER.COM/INSTANTANSWERS for instant answers 24 hours a day.

If you can’t find the answer or do not have access to the internet,

call 1-800-544-6986 from 8 a.m. to 5 p.m. EST Mon. -- Fri. to speak with an agent. Please have the catalog number available when you call.

SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE.

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA.

ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

Cat. # SL302B

Form # 90558474

 

Nov. 2009

Copyright © 2009 Black & Decker

Printed in China

24

90558474 SL302B.qxp:SL302B ManualENSPFR 073008 11/25/09 1:20 PM Page 2

SAFETY GUIDELINES / DEFINITIONS

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

CAUTION: Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may result in property damage.

RISK OF UNSAFE OPERATION. When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious injury and property damage. There are certain applications for which tools and equipment are designed. Black & Decker strongly recommends that this product NOT be modified and/or used for any application other than for which it was designed. Read and understand all warnings and operating instructions before using any tool or equipment.

IMPORTANT SAFETY INSTRUCTIONS

GENERAL SAFETY WARNINGS AND INSTRUCTIONS FOR ALL APPLIANCES

READ ALL INSTRUCTIONS

WARNING: Read all instructions before operating product. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

AVOID DANGEROUS ENVIRONMENTS Don’t use appliances in damp or wet locations. Don’t use appliances in the rain.

KEEP CHILDREN AWAY. All visitors should be kept at a distance from work area.

STORE IDLE APPLIANCES INDOORS. When not in use, appliances should be stored indoors in dry, and high or locked-up place – out of reach of children.

DON’T FORCE APPLIANCE. It will do the job better and with less likelihood of a risk of injury at the rate for which it was designed.

USE RIGHT APPLIANCE. Do not use the appliance for any job except that for which it is intended.

DRESS PROPERLY. Do not wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves and substantial, non-skid footwear are recommended when working outdoors. Wear protective hair covering to contain long hair.

USE SAFETY GLASSES AND OTHER SAFETY EQUIPMENT. Use safety goggles or safety glasses with side shields, complying with applicable safety standards and, when needed, a face shield. Also use face or dust mask if operation is dusty. This applies to all persons in the work area. Also use a hard hat, hearing protection, gloves, safety shoes and dust collection systems when specified or required. Safety glasses or the like are available at extra cost at your local dealer or Black & Decker Service Center.

DON’T ABUSE CORD. Never carry appliance by cord or yank it to disconnect from receptacle. Keep cord from heat, oil, and sharp edges.

DON’T OVERREACH. Keep proper footing and balance at all times.

DISCONNECT APPLIANCE. The AC Charger and DC Charging Adapter should be maintained in a readily operable condition. To avoid damage to the unit or Adapter, disconnect the unit from any power supply when not in use, before cleaning, during lightning storms, and changing accessories or when it will be unused for long periods of time. To disconnect the unit from the power supply, the AC Charger must be completely disconnected from any AC extension cord and the DC Charging Adapter.

AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in appliance with finger on switch. Be sure switch is off when plugging in.

GROUND FAULT CIRCUIT INTERRUPTER (GFCI) protection should be provided on the circuits or outlets to be used. Receptacles are available having built in GFCI protection and may be used for this measure of safety.

USE OF ACCESSORIES AND ATTACHMENTS. The use of any accessory or

attachment not recommended for use with this appliance could be hazardous. Note: Refer to the accessory section of this manual for further details.

STAY ALERT. Watch what you are doing. Use common sense. Do not operate tool when you are tired.

CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual. Have defective switches replaced by authorized service center. Do not use tool if switch does not turn it ON and OFF.

DO NOT OPERATE portable electric tools near flammable liquids or in gaseous or explosive atmospheres. Motors in these tools normally spark, and the sparks might ignite fumes.

OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked.

EXTENSION CORDS. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

Minimum Gauge for Cord Sets

Volts

 

 

Total Length of Cord in Feet

 

120V

 

0-25

26-50

51-100

101-150

 

 

 

(0-7.6m)

(7.6-15.2m)

(15.2-30.4m)

(30.4-45.7m)

240V

 

0-50

51-100

101-200

201-300

Ampere Rating

(0-15.2m)

(15.2-30.4m)

(30.4-60.9m)

(60.9-91.4m)

 

 

 

 

More

Not more

 

American Wire Gauge

 

Than

Than

 

 

 

 

0

-

6

18

16

16

14

6

-

10

18

16

14

12

10 -

12

16

16

14

12

12 -

16

14

12

Not Recommended

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK:

Do not plug in a power supply without the bulb lens and cover in place.

Do not put spotlight in water or other liquid. Do not place or store spotlight where it can fall or be pulled into a tub or sink.

Keep the lens in place.

Do not operate this unit without the lens.

WARNING: FIRE HAZARD: Never contact combustible material to the lens.

WARNING: BURN HAZARD: Hot lens. May cause property damage or fire. Do not touch or obstruct lens.

All halogen lights give off heat:

Do not touch lens while operating.

Keep combustibles away from spotlight lens. Extreme heat can cause fires.

Never place the light face-down on any surface when lit and following recent use.

Do not touch the lens or enclosure as it becomes hot during operation and remains hot for several minutes after the spotlight is switched off.

Allow the spotlight to fully cool down before storage or charging.

Do not leave the spotlight unattended. Keep children and animals away from the work area.

CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:

Use only on a flat, stable surface. When a cart is used, use caution when moving the spotlight/cart combination to avoid injury from tip-over. Never place the light face-down on any surface.

Never look directly into the light or shine the light into another person’s eyes.

Keep sharp objects away from lens — it is glass and can break.

The lens of the light blocks harmful UV radiation. Do not use if the lens becomes cracked or broken.

Do not immerse spotlight in water.

Do not drop or throw spotlight. It contains glass and a sealed lead acid battery.

Use in a dry location only.

Do not open body casing. There are no user-serviceable parts inside.

CHARGING SAFETY WARNINGS

AND GUIDELINES

Before using battery charger, read all instructions and cautionary markings on battery charger and unit.

CAUTION: To reduce the risk of injury, charge only Black & Decker Batteries. Other types of batteries may burst causing personal injury and damage.

NEVER ATTEMPT TO USE THE AC CHARGER AND DC CHARGING PORT SIMULTANEOUSLY.

Plug in the charging adapter at the spotlight first, then plug into the charging source.

2

3

 

 

 

 

 

 

 

 

 

 

 

 

90558474 SL302B.qxp:SL302B ManualENSPFR 073008 11/25/09 1:20 PM Page 4

Note: To ensure maximum battery life do not overcharge. Only charge until the green LED charge status indicator lights.

Do not expose charger to rain or snow. Use in a dry location only.

Do not crush, cut, pull or expose charger cords to extreme heat.

Position charger cords so they do not become entangled or become a safety hazard. Keep charger cords away from sharp edges.

To reduce risk of damage to plug and cord, pull by plug rather than cord when disconnecting unit from the charger.

Use of improper extension cord could result in a risk of fire, electric shock or electrocution.

Use only the supplied chargers when charging this spotlight. The use of any other charger could damage the spotlight or create a hazardous condition.

Use only one charger when charging.

Do not attempt to charge the unit if the charger plug is damaged— return the unit to manufacturer for repair.

Do not attempt to open the charger. There are no customer serviceable parts inside. Return to manufacturer for repair.

All ON/OFF switches should be in the OFF position when the unit is charging or not in use. Make sure all switches are in the OFF position before connection to a power source or load.

After charging/recharging, disconnect charger or extension cord and wait 5 minutes before use.

This unit contains a non-spillable battery. To avoid possible damage that may shorten the unit’s working life, protect it from direct sunlight, direct heat and/or moisture.

FIRST AID – SKIN: If battery acid comes in contact with skin, rinse immediately with water, then wash thoroughly with soap and water. If redness, pain, or irritation occurs, seek immediate medical attention.

EYES: If battery acid comes in contact with eyes, flush eyes immediately, for a minimum of 15 minutes and seek immediate medical attention.

IMPORTANT:

This unit is delivered in a partially charged state. Fully charge unit for 18-24 hours using the AC charging method before using for the first time. Green indicator will light when fully charged.

Read And Understand This Instruction Manual Before Using This Unit.

SAVE THESE INSTRUCTIONS

INTRODUCTION

Thank you for choosing the Black & Decker® V-2 Million Power SeriesSpotlight. Please read this guide carefully before use to ensure optimum performance and to avoid damage to the unit.

CHARGING/RECHARGING THE SPOTLIGHT

This unit is shipped in a partially charged state. Charge unit BEFORE first use using the 120 Volt AC Charger for 18-24 hours or until the green Battery Status LED Indicator lights. Charge after each use until green Charge Status LED Indicator lights.

Charging/Recharging Using the 120 Volt AC

Charger and a Standard Household

Extension Cord (not included)

Plug a standard North American 120 volt AC extension

CHARGE STATUS LED

cord (not included) into the 120 Volt AC Charger on the

INDICATORS

back of the unit.

 

Make sure the Spotlight is OFF (the Trigger Lock is in the OFF

position and the Trigger is not depressed). BUILT-IN 120V AC

Charge for 18-24 hours or until the green Battery Status LED

Indicator lights.

CHARGER

Notes: To extend battery life, disconnect the charger after 48 hours.

All batteries lose charge with time, especially when they are warm. Recharge the unit every two months for 18-24 hours when not in frequent use.

If the unit is not going to be used for extended periods, disconnect the charger and store in a cool, dry place.

Charging/Recharging Using the 12 Volt DC Charging Adapter

Plug the barrel tip of the supplied 12 Volt DC Charging Adapter into the 12 Volt DC Charging Port (shown in the illustration below).

12 VOLT DC CHARGING PORT (UNDERSIDE OF UNIT)

12 VOLT DC CHARGING ADAPTER

Insert the 12 volt DC plug end into the accessory outlet of your vehicle or other 12 volt DC power source.

FEATURES

Powerful, focused quartz halogen beam with Dimmer Switch for high and low settings

Safety cap protects 120 volt AC charger

Comfortable pistol grip, handle and carry lanyard

Charge Status LED Indicator

UL listed, built-in 120 volt AC charger that works with a standard household extension cord (not included)

12 volt DC charging adapter included

Rechargeable, non-spillable, sealed lead acid battery

Make sure the Spotlight is OFF (the Trigger Lock is in the OFF position and the Trigger is not depressed).

Charge until the green Charge Status LED Indicator lights.

Notes:When using a vehicle’s 12 volt DC accessory outlet as a charging source, be aware that some vehicles require you to turn on the ignition to power the accessory outlet.

To avoid deeply discharging your vehicle battery we recommend to have the vehicle running while recharging the light with the DC recharge adapter.

WARNING: NEVER ATTEMPT TO USE THE AC CHARGER AND DC CHARGING PORT SIMULTANEOUSLY.

Controls and Functions

DIMMER SWITCH

CARRY HANDLE

CHARGE STATUS LED

 

INDICATOR

 

120 VOLT AC CHARGER

 

(BACK OF UNIT)

QUARTZ HALOGEN BULB

 

CARRY LANYARD

 

 

 

 

TRIGGER LOCK

12 VOLT DC CHARGING PORT

 

PISTOL GRIP HANDLE

(UNDERSIDE OF UNIT)

ON/OFF

 

TRIGGER

 

OPERATING INSTRUCTIONS

The Trigger Switch is located on the front of the pistol-grip handle of the spotlight (refer to the “Controls and Functions” illustration).

Turn on the Spotlight by squeezing the ON/OFF Trigger.

Turn off the Spotlight by releasing the ON/OFF Trigger.

To lock the Trigger in the ON position for continuous operation, squeeze the ON/OFF Trigger and slide theTrigger Lock Button located on the side on the handle DOWN (refer to the “Controls and Functions” illustration). The Spotlight will stay ON until you slide the Trigger Lock Button back UP.

Dimmer Switch

The Dimmer Switch is located on the top of the Spotlight (refer to the “Controls and Functions” illustration). Sliding the switch forward (toward the Spotlight bulb) sets the Spotlight on High Beam; sliding the switch backward sets the Spotlight on Low Beam.

Using the Carry Handle as a Stand For Hands-Free Operation

Invert the unit to use the Carry Handle as a stand, and set it upon a flat, stable surface for hands-free operation.

Using the Built-In Carry Lanyard

The Carry Lanyard may be used to store or carry the Spotlight; and also allows you to position the Spotlight for convenient, hands-free operation.

4

5

 

 

 

 

 

 

 

 

 

 

 

 

90558474 SL302B.qxp:SL302B ManualENSPFR 073008 11/25/09 1:20 PM Page 6

CAUTION: TO REDUCE THE RISK OF PRODUCT DAMAGE:

Only use the Carry Lanyard for carrying or hanging the Spotlight. The Carry Lanyard is not intended to support additional weight. Do not attach or hang anything additional to the light or risk of breakage may occur.

When light is hung by the Carry Lanyard, do not shake the light or object that it is hanging from. Do not hang the light from electrical wires or anything that it is not secure.

CARE AND MAINTENANCE

All batteries lose charge with time, especially when they are warm. Recharge the unit every two months when not in frequent use, preferably using the 120 volt AC method.

Never submerge the unit in water. If the unit gets dirty, gently clean the outer surfaces of the spotlight unit with a soft cloth moistened with a mild solution of water and detergent.

Battery Replacement/Disposal

BATTERY REPLACEMENT

The battery should last the service life of the unit. Contact Technical Support toll-free at 1-800-544-6986 for any information you may need.

BATTERY DISPOSAL Contains a maintenance-free, sealed, non-spillable, lead acid battery, which must be disposed of properly. Recycling is required — contact your local authority for information. Failure to comply with local, state and federal regulations can result in fines or imprisonment. For more information on recycling this battery, call toll-free 1-800-544-6986.

WARNINGS:

Do not dispose of the battery in fire as this may result in an explosion.

Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to prevent shorting (shorting can result in injury or fire).

Do not expose battery to fire or intense heat as it may explode.

For more information on recycling this battery, call toll-free 1-800-544-6986.

12 Volt DC Charging Adapter Plug Fuse Replacement

The fuse in the plug end of the 12 Volt DC Charging Adapter protects the adapter’s charging circuit. If the 120 Volt AC Charger operates, but the DC charging adapter does not, then this fuse may be opened (blown).

To replace the fuse:

1.Unscrew the end cap of the DC plug (counterclockwise).

2.Remove spring center contact and fuse.

3.Check fuse with a continuity checker.

4.If blown, locate a replacement 2 amp/250 volt fuse.

5.Replace the fuse, spring, contact and end cap.

6.Screw end cap clockwise until it is finger tight – DO NOT OVER-TIGHTEN.

7.Test for proper operation of the 12 Volt DC Charging Adapter.

TROUBLESHOOTING

Problem

Solution

Spotlight will not charge (green

1.

Check connection to the 120 Volt AC Charger (or DC Charging Port).

Charge Status LED Indicator does

2.

Check connection to AC (or DC) power source.

not light)

3.

Confirm there is a functioning AC (or DC) current.

 

4.

Make sure the Trigger is not pressed (pressing the Trigger when one

 

 

of the charging adapters is plugged in interrupts the charging

 

 

process).

 

5.

Make sure the Trigger Lock is not engaged. It is possible to have left

 

 

the Trigger Lock ON when the battery discharged. The Spotlight will

 

 

not charge until the Trigger is unlocked.

 

6.

If the Spotlight will not charge after checking all of the above, contact

 

 

Technical Support toll-free at 1-800-544-6986.

Problem

Solution

Spotlight will not operate

1.

If you suspect the bulb is blown, check the filament. If the filament is

 

 

coiled and unbroken, the bulb is not blown. If bulb is blown, call

 

 

1-800-544-6986 to locate the nearest authorized service center. The

 

 

bulb is NOT user-replaceable.

 

2.

The light may be charging/recharging using the 12 volt DC charging

 

 

adapter. The unit will not operate while charging/recharging via the

 

 

DC charger. Unplug from the 12 volt DC power source.

 

3.

The battery may be completely discharged. Charge the unit following

 

 

the directions in this Instruction Manual.

 

4.

If the Spotlight does not operate after recharging as directed, contact

 

 

Technical Support toll-free at 1-800-544-6986.

Cannot depress trigger

Slide Trigger Lock Button on side of handle UP to unlock the Trigger.

ACCESSORIES

Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call: 1-800-544-6986.

WARNING: The use of any accessory not recommended for use with this spotlight could be hazardous and will void manufacturer’s warranty.

SERVICE INFORMATION

All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under "Tools–Electric" or call: 1-800-544-6986 or visit www.blackanddecker.com.

CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE: Do not open body casing. There are no user-serviceable parts inside.

FULL ONE YEAR HOME USE WARRANTY

Black & Decker (U.S.) Inc. warrants this product for one year against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways.

The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or replacement at our option. Proof of purchase may be required. Black & Decker owned and authorized Service Centers are listed under "Tools-Electric" in the yellow pages of the phone directory and on our website www.blackanddecker.com.

This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary from state to state or province to province. Should you have any questions, contact the manager of your nearest Black & Decker Service Center. This product is not intended for commercial use.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-544- 6986 for a free replacement.

SPECIFICATIONS

Spotlight Bulb:

Battery:

Embedded AC Charger:

DC Plug Fuse:

Imported by Black & Decker (U.S.)

Inc.,

701 E. Joppa Rd. Towson, MD 21286 U.S.A.

12 volt, H3 series, dual-filament 55W/35W bulb Maintenance-free, sealed lead acid, 12 volt, 3 amp hour UL Listed Class 2, 12 volt DC (300 mA)

2 A/250 V

See ‘Tools-

Electric’

– Yellow Pages –

for Service &

Sales

6

7

 

 

 

 

 

 

 

 

 

 

 

 

Loading...
+ 8 hidden pages