BLOWER VAC |
INSTRUCTION MANUAL
Date Code:
Catalog Number BV2500, BV9000
THANK YOU FOR CHOOSING BLACK & DECKER!
GO TO WWW.BLACKANDDECKER.COM/NEWOWNER
TO REGISTER YOUR NEW PRODUCT.
BEFORE RETURNING THIS PRODUCT FOR ANY REASON PLEASE CALL
1-800-544-6986
BEFORE YOU CALL, HAVE THE CATALOG No.AND DATE CODEAVAILABLE. IN MOST CASES,A
BLACK & DECKER REPRESENTATIVE CAN RESOLVE THE PROBLEM OVER THE PHONE. IF YOU HAVEA SUGGESTION OR COMMENT, GIVE USACALL. YOUR FEEDBACK IS VITALTO BLACK & DECKER.
KEY INFORMATION YOU SHOULD KNOW:
•Before operating, make sure that either the blower or vacuum tube assembly is locked in place.
•The power switch must be OFF in order to depress the release button for changing blower and vacuum tube assemblies.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
VEA EL ESPAÑOL EN LA CONTRAPORTADA.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
Form No. 625233-01 Rev. 1 |
Cat. # BV2500, BV9000 |
(MARCH ‘07) |
Copyright © 2007 Black & Decker |
|
Printed in Mexico |
WARNING: IMPORTANT SAFETY WARNINGS AND INSTRUCTIONS
TO REDUCE RISK OF INJURY:
•Before any use, be sure everyone using this tool reads and understands all safety instructions and other information contained in this manual.
•Save these instructions and review frequently prior to use and in instructing others.
WARNING: When using an electric appliance, basic safety precautions should always be followed to reduce risk of fire, electric shock, and personal injury, including the following.
WARNING: Some dust created by this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
•compounds in fertilizers
•compounds in insecticides, herbicides and pesticides
•arsenic and chromium from chemically treated lumber
To reduce your exposure to these chemicals, wear approved safety equipment such as dust masks that are specially designed to filter out microscopic particles.
WARNING: This product contains chemicals, including lead, known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling.
CAUTION: Wear appropriate personal hearing protection during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss.
SAFETY GUIDELINES - DEFINITIONS
It is important for you to read and understand this manual.
The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may result in property damage.
READ ALL INSTRUCTIONS BEFORE USING BLOWER.
GENERAL SAFETY WARNINGS AND INSTRUCTIONS FOR ALL TOOLS
•READ and follow all instructions.
•DO NOT place inlet or outlet of vacuum near eyes or ears when operating.
•THIS APPLIANCE IS PROVIDED WITH DOUBLE INSULATION. Use only identical replacement parts. See instructions for servicing of double insulated appliances.
•STORE IDLE TOOLS. When not in use, the unit should be stored in a dry, high or locked-up place - out of reach of children.
•DON'T OVERREACH. Keep proper footing and balance at all times.
•DO NOT pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.
•MAINTAIN TOOL WITH CARE. Keep fan area clean for best and safest performance. Follow instructions for proper maintenance.
•DO NOT attempt to repair the blower/vac. To assure product safety and reliability, repairs, maintenance, and adjustments should be performed by Black & Decker service centers or authorized service stations, always using Black & Decker replacement parts.
•DO NOT operate blower/vac in a gaseous or explosive atmosphere. Motors in these tools normally spark, and the sparks might ignite fumes.
•DO NOT use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present.
•USE EXTRA CARE when cleaning on stairs.
•DO NOT leave appliance when plugged in. Unplug from outlet when not in use and before servicing.
•DO NOT allow to be used as a toy. Close attention is necessary when used by or near children. Not recommended for use by children.
•DO NOT attempt to clear clogs from tool without first unplugging it.
•USE ONLY as described in this manual. Use only manufacturer's recommended attachments.
•DO NOT use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center.
•DO NOT pull or carry by cord, use cord as a handle, or pull cord around sharp edges or corners. Keep cord away from heated surfaces.
•DO NOT unplug by pulling on cord. To unplug, grasp the plug, not the cord.
•DO NOT put any objects into openings. Do not use with any opening blocked; keep free of dust, lint, hair and everything that may reduce air flow.
•KEEP hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
•TURN OFF all controls before unplugging.
•DO NOT vacuum water, other liquids, or wet objects such as leaves. Never immerse any part of the tool in liquid.
•DO NOT handle plug or appliance with wet hands.
•KEEP CHILDREN, BYSTANDERS AND ANIMALS AWAY from the work area a minimum of 30 feet (10 meters) when starting or operating the tool.
•INSPECT THE AREA before using the tool. Remove all debris and hard objects such as rocks, glass, wire, etc. that can ricochet, be thrown, or otherwise cause injury or damage during operation. As a vacuum, the tool is designed to pick up dry material such as leaves, grass, small twigs, and bits of paper. Do not vacuum stones, gravel, metal, broken glass, etc.
WARNING: To reduce the risk of electrical shock; do not expose to rain, do not use on wet surfaces. Store indoors.
WARNING: Turn off and unplug unit, then wait until fan stops or at least 10 seconds before removing the blower or vacuum tube assemblies.
SAVE THESE INSTRUCTIONS
Release Button |
OFF |
ON |
Bouton de Dégagement |
||
Botones de Liberación |
Arrêt |
En Marche |
|
Apagada |
Encendido |
O
Switch
Interrupteur
Interruptor
2
3
10
Blowing Mode
de
7
Extension Tube
Tube de Rallange
Tubo de Extension
Vacuum Tube
Tube D´Aspiration
Tubo de Aspirado
7A |
7B |
Vacuuming Mode
Aspirateur
Modo de
Aspiradora
6
B
C
SERVICING OF DOUBLE INSULATED APPLIANCES
Your Blower/Vac is double-insulated to give you added safety. In a double insulated appliance, two systems of insulation are provided instead of grounding. No grounding means is provided on a double insulated appliance, nor should a means for grounding be added to the appliance. Servicing a double insulated appliance requires extreme care and knowledge of the system and should be done only by qualified service personnel. Replacement parts for a double insulated appliance must be identical to the parts they replace. A double insulated appliance is marked with the words double insulated or "double insulation". The symbol (square within a square) may also be marked on the appliance.
SAFETY RULES AND INSTRUCTIONS: EXTENSION CORDS
Double insulated tools have 2-wire cords and can be used with 2-wire or 3-wire extension cords. Only round jacketed extension cords should be used, and we recommend that they be listed by Underwriters Laboratories (U.L.) (C.S.A. in Canada). If the extension will be used outside, the cord must be suitable for outdoor use. Any cord marked as outdoor can also be used for indoor work.
An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety, and to prevent loss of power and overheating. The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge has more capacity than 18 gauge. When using more than one extension to make up the total length, be sure each individual extension contains at least the minimum wire size.
To determine the minimum wire size required, refer to the chart below. Before using an extension cord, inspect it for loose or exposed wires, damaged insulation, and defective fittings. Make any needed repairs or replace the cord if necessary.
|
|
|
Minimum Gage for Cord Sets |
|
||
Volts |
|
Total Length of Cord in Feet |
||||
120V |
|
0-25 |
26-50 |
51-100 |
101-150 |
|
|
|
|
(0-7,6m) |
(7,6-15,2m) (15,2-30,4m) (30,4-45,7m) |
||
240V |
|
0-50 |
51-100 |
101-200 |
201-300 |
|
|
|
|
(0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m) |
|||
Ampere Rating |
|
|
|
|
||
More |
|
Not more |
American Wire Gage |
|
||
Than |
|
Than |
|
|
|
|
0 |
- |
6 |
18 |
16 |
16 |
14 |
6 |
- |
10 |
18 |
16 |
14 |
12 |
10 |
- |
12 |
16 |
16 |
14 |
12 |
12 |
- |
16 |
14 |
12 |
Not Recommended |
|
SAFETY WARNINGS AND INSTRUCTIONS: POLARIZED PLUG
To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other). This equipment must be used with a suitable polarized 2 wire or 3 wire extension cord. Polarized connections will fit together only one way. Make sure that the receptacle end of the extension cord has large and small blade slot widths. If the plug does not fit fully into the extension cord, reverse the plug. If it still does not fit, obtain a suitable extension cord. If the extension cord does not fit fully into the outlet, contact a qualified electrician to install the proper outlet. Do not change the tool plug or extension cord in any way.BEFORE OPERAT
BEFORE OPERATINGG
•SECURING POWER SUPPLY CORD - Secure the extension cord in the tool's built-in cord retainer as shown in Figure 12 or secure the power supply cord and a suitable extension cord as shown in Figure 13.
SWITCH
NOTE: The switch will not operate if the release button, shown in Figure 1, is depressed. To turn the tool ON, slide the switch forward, as shown in Figure 1. To turn tool OFF, slide switch to the rear.
OPERATION
USE AS A BLOWER: ALWAYS WEAR SAFETY GLASSES, WEAR A FILTER MASK IF THE OPERATION IS DUSTY. USE OF RUBBER GLOVES AND SUBSTANTIAL FOOTWEAR IS RECOMMENDED WHEN WORKING OUTDOORS. FOR HOUSEHOLD USE ONLY.
•BLOWER MODE
Ensure that the unit is switched OFF and is disconnected from the power supply. Assemble blow tube as shown in Figure 2. (This only needs to be done the first time you assemble the unit.)
WARNING: When turning the tool off for tube installation or any other reason, wait 10 seconds for the fan to stop rotating before disassembly.
Attach the blower tube assembly (The assembly includes the blower tubes, the fan chamber and the blower air speed control mechanism) to the front of the tool, as shown in Figure 3 by inserting point A into the matching recess marked point B, also shown in Figure 3. Swing the tube up to engage the lock, as shown in Figure 4.
NOTE: The lock will not engage if the ON/OFF switch is in the forward (ON) position.
Hold the end of the blower tube approximately 7 inches (180mm) above the ground and turn the tool ON. Using a sweeping motion, from side to side, advance slowly keeping the accumulated debris (leaves,grass clippings etc.) in front of you, as shown in Figure 5. Once you have blown the debris into a pile, you can convert to vacuum mode to collect the debris for disposal.
• BLOWER AIR SPEED CONTROL
Your Blower Vac has a variable air speed feature that allows you to select the air speed that best fits your needs. To adjust the air speed, simply slide the collar. This will allow movement over the full range of 1 3/4"(44.5mm). With the slide collar in the "A" position, as shown in Figure 6, the maximum blower speed will be 200 mph (320 kph). When pushed forward to position "C" ( as far from the tool housing as possible; about 1 3/4"{44.5mm}) the speed will be approximately 140 mph (225 kph). Position "B" (midway between the two) permits infinite adjustment between positions "A" and "C". A little practice will help you determine what is the best speed for your application.
USE AS A VACUUM CLEANER: ALWAYS WEAR SAFETY GLASSES. WEAR A FILTER MASK IF THE OPERATION IS DUSTY. USE OF RUBBER GLOVES AND SUBSTANTIAL FOOTWEAR IS RECOMMENDED WHEN WORKING OUTDOORS. FOR HOUSEHOLD USE ONLY.
•REMOVING THE BLOWER TUBE ASSEMBLY
Switch off the unit and unplug from the outlet.
To disconnect the blower tube assembly from the tool, depress the release button, shown in Figure 1, ensuring that the tube does not fall to the ground.
NOTE: The release button will not depress if the ON/OFF switch is in the forward (ON) position.
•VACUUMING MODE
Ensure that the unit is switched off and disconnected from the power supply. Position the vacuum tube and extension tube as shown in Figure 7. Push the extension tube into the vacuum tube until it snaps into place and the arrows shown in Figure 7A are covered as in Figure 7B. If necessary, this can be made easier by wiping the end of the extension tube with a cloth dampened with soapy water only.
Attach the vacuum tube assembly (The assembly includes the extension tube, the vacuum tube and the fan chamber.) to the front of the tool. Insert point "A", shown in Figure 8, into the matching recess in the front of the tool point "B", also shown in Figure 8, and swing the tube up to engage the lock, as shown in Figure 9.
Attach the collection bag to the vacuum outlet using the bayonet fitting, as shown in Figure 10.
Hold the vacuum as shown in Figure 11. Tilt the vacuum tube slightly and use a sweeping action similar to the action described under Blower Mode. The light debris will flow into and through the vacuum tube into the collection bag. Things such as leaves and small twigs will be mulched as they pass through the fan chamber so that the collection bag will hold a lot of debris.
When the collection bag gets full, suction will noticeably decrease. Turn off and unplug the tool and unzip the bag to empty before continuing to operate.
CAUTION: NEVER UNZIP THE COLLECTION BAG WITHOUT FIRST TURNING OFF AND UNPLUGGING THE VACUUM.
NOTE: If the suction decreases and the bag is not full, the vacuum tube is probably clogged with debris. Turn off and unplug the vacuum and clear the tube before continuing.
TROUBLESHOOTING
Problem |
Possible Cause |
Possible Solution |
• Unit will not start. |
• Cord not plugged in. |
• Plug tool into a working outlet. |
|
• Circuit fuse is blown. |
• Replace circuit fuse. (If the product |
|
|
repeatedly causes the circuit fuse to |
|
|
blow, discontinue use immediately and |
|
|
have it serviced at a Black & Decker |
|
|
service center or authorized servicer.) |
|
• Circuit breaker is tripped. • Reset circuit breaker. (If the product |
|
|
|
repeatedly causes the circuit breaker to |
|
|
trip, discontinue use immediately and |
|
|
have it serviced at a Black & Decker |
|
|
service center or authorized servicer.) |
|
• Cord or switch is |
• Have cord or switch replaced at Black |
|
damaged. |
& Decker Service Center or Authorized |
|
|
Servicer |
For assistance with your product, visit our website www.blackanddecker.com for the location of the service center nearest you or call the BLACK & DECKER help line at
1-800-544-6986.
MAINTENANCE
•CLEANING AND STORAGE
TURN OFF AND UNPLUG TOOL! (Unplug extension cord at power source.)
Use only mild soap and a damp cloth to clean the tool. Clean out any clippings which may have accumulated in the Blower/Vac. When used properly with dry leaves the fan chamber of your Blower/Vac should remain clean. If damp earth and debris are ingested some of the particles may build up on the inside of the fan chamber. If this happens the performance of the unit will decrease. This area can be cleaned out by gently wiping out with a damp rag after disconnecting from the power source. Your Blower/Vac should be stored in a dry place.
CAUTION: DO NOT POUR OR SPRAY WATER ON THE TOOL IN AN ATTEMPT TO CLEAN.
Do not store the tool on or adjacent to fertilizers or chemicals. Such storage can cause rapid corrosion of the metal parts.
Use only mild soap and a damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call:
1-800-544-6986).
WARNING: The use of any accessory not recommended for use with this tool could be hazardous.
Leaf Collection System Cat. No. BV-006 (Available from your dealer at extra cost.) (BV-006 is included with BV9000).
The Leaf Collection System replaces the collection bag with a system of collecting debris directly into a 30-33 gallon trash can. Complete directions for the system’s use are included. (Trash can not included.)
SERVICE INFORMATION
All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under "Tools—Electric" or call:
1-800-544-6986 or visit www.blackanddecker.com
FULL TWO-YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or replacement at our option. Proof of purchase may be required.Black & Decker owned and authorized Service Centers are listed under "Tools-Electric" in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary from state to state or province to province. Should you have any questions, contact the manager of your nearest Black & Decker Service Center. This product is not intended for commercial use.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-544-6986 for a free replacement.
Imported by |
See ‘Tools-Electric’ |
|
Black & Decker (U.S.) Inc., |
||
701 |
E. Joppa Rd. |
– Yellow Pages – |
Towson, |
MD 21286 U.S.A. |
for Service & Sales |
Loading...