Bissell 24A4 User Manual

Download

Page 1

USER GUIDE

PROHEAT LIFT-OFF

24A4, 30K7, 66E1, 80X9 SERIES

Page 2

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING YOUR DEEP CLEANER.

When using an electrical appliance, basic precautions should be observed, including the following:

WARNING

To reduce The risk of fire, elecTric shock, or injury:

» Connect to a properly grounded

outlet only. See grounding instructions. Do not modify the 3-prong grounded plug.

» Do not leave appliance when it is

plugged in. Unplug from outlet when not in use and before servicing.

» Do not expose to rain, store

indoors.

» Do not allow to be used as a toy.

Close attention is necessary when used by or near children.

» Do not use for any purpose other

than described in this User ’s Guide. Use only manufacturer’s recommended attachments.

» Do not use with damaged cord

or plug. If appliance is not working as it should, or has been dropped, damaged, left outdoors, or dropped into water, have it repaired at an authorized service center.

» Do not pull or carry by cord, use

cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.

» Do not unplug by pulling on

cord. To unplug, grasp the plug, not the cord.

» Do not handle plug or appliance

with wet hands.

» Do not put any object into open-

ings. Do not use with any opening blocked; keep openings free of dust, lint, hair, and anything that may reduce air flow.

» Keep hair, loose clothing, fingers,

and all parts of body away from openings and moving parts.

» Turn off all controls before plug-

ging or unplugging appliance.

» Use extra care when cleaning

on stairs.

» Do not use to pick up flammable

or combustible materials (lighter fluid, gasoline, kerosene, etc.) or use in areas where they may be present.

» Do not use appliance in an

enclosed space filled with vapors given off by oil base paint, paint thinner, some moth proofing substances, flammable dust, or other explosive or toxic vapors.

» Do not use to pick up toxic

material (chlorine bleach, ammonia, drain cleaner, etc.).

» Do not pick up anything that

is burning or smoking, such as cigarettes, matches, or hot ashes.

» Use only BISSELL cleaning

products intended for use with this appliance to prevent internal component damage. See the Cleaning Fluid section of this guide.

» Unplug before connecting

TurboBrush Tool.

» Do not immerse. Use only on

surfaces moistened by the

cleaning process. » Keep appliance on a level surface. » Do not carry the appliance while

in use.

SAVE THESE INSTRUCTIONS FOR FUTURE USE

This model is for household use only. Commercial use of this unit voids the manufacturer’s warranty.

WARNING

Improper connection of the equipment-grounding conductor can result in a risk of electrical shock. Check with a qualiﬁed electrician or service person if you aren’t sure if the outlet is properly grounded. DO NOT MODIFY THE PLUG. If it will not ﬁt the outlet, have a proper outlet installed by a qualiﬁed electrician. This appliance is designed for use on a nominal 120-volt circuit, and has a grounding attachment plug that looks like the plug in the illustration. Make certain that the appliance is connected to an outlet having the same conﬁguration as the plug. No plug adapter should be used with this appliance.

www.BISSELL.com

800.237.7691

GROUNDING INSTRUCTIONS

This appliance must be connected to a grounded wiring system. If it should malfunction or break down, grounding provides a safe path of least resistance for electrical current, reducing the risk of electrical shock. The cord for this appliance has an equipment-grounding conductor and a grounding plug. It must only be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Grounded Outlets

Grounding Pin

Page 3

Th for buying a BISSELL dp cleer

We’re glad you purchased a BISSELL deep cleaner. Everything we know about floor care went into the design and construction of this complete, high-tech home cleaning system.

Your BISSELL deep cleaner is well made, and we back it with a limited two-year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Care department, so, should you ever have a problem, you’ll receive fast, considerate assistance.

My great-grandfather invented the floor sweeper in 1876. Today, BISSELL is a global leader in the design, manufacture, and service of high quality homecare products like your BISSELL deep cleaner.

Thanks again, from all of us at BISSELL.

Safety Instructions...........2

Product View................4

Assembly .................5-6

Operations ............... 7-12

Maintenance & Care ......13-15

Troubleshooting ..........16-17

Replacement Parts ......... 17

Accessories ................18

Warranty ...................19

Consumer Care.............19

Product Registration....... 20

Mark J. Bissell Chairman & CEO

Tips

» Deep cleaning stairs and high-trac areas on a regular

basis helps prolong carpet life.

» Check upholstery stung before cleaning. Colored

stung may bleed through the fabric when it becomes wet.

www.BISSELL.com

» Before turning o the machine, suction up clean

water to thoroughly rinse out the interior of the ﬂex hose. Then, lift the cleaning tool and point it upwards to drain any remaining water into the dirty water/ collection tank.

800.237.7691

Page 4

Product View

1 Upper Handle 2 Heat Indicator Light 3 Carry Handle 4 Specialty Tool

(tools vary by model) 5 Formula & Water Tank 6 Power Button 7 Power Cord 8 Dirty Tank 9 Flex Hose

10 Quick Release™ Cord Wrap

11 Portable Spot Cleaning

Release Pedal 12 EdgeSweep® Brushes 13 Removeable Nozzle 14 Spray Trigger 15 Tool Storage 16 Support Handle 17 Hose Secure Latch 18 Recline Pedal

www.BISSELL.com

800.237.7691

Page 5

Asmbly

IMPORTANT

ASSEMBLY INSTRUCTIONS

Use a minimum of a #2 x 4" or #2 x 100mm Philips screwdriver for assembly.

Your deep cleaner comes in two easy to assemble components:

1. Upper handle

2. Portable spot cleaner/Base

The only tool you will need to assemble your cleaner is a Phillips screwdriver.

1. Slide the upper handle onto the body of the machine by guiding the 2 posts on the body into the opening on the upper handle.

2. Firmly holding the upper handle in place, screw 2 screws into the marked holes at an upward angle above the support handle.

3. At an upward angle, screw the remaining 2 screws into the marked outermost holes under the support handle.

4. Wrap power cord around Quick Release Cord Wrap.

5. Wrap flex hose around the hose wrap and secure with hose secure latch.

6. Align the product as image 4 shows and firmly push down the portable spot cleaner until it is secured on both sides.

7. Check latches on both sides to confirm it is secured.

To further check if the portable spot cleaner is secure, plug in and turn on to verify that the heat indicator light is illuminated. If the heat indicator light does not illuminate, release the pod and re-secure by pushing firmly until both sides snap into place.

8. Snap attachment(s) into the back of unit.

NOTE: Portable spot cleaner must be fully secure to operate in the upright mode.

WARNING

Do not plug in your deep cleaner until you are familiar with all instructions and operating procedures.

Cord side

Tip

» Deep cleaning carpeting regularly can reduce dust and allergens in your home.

Hose side

www.BISSELL.com

800.237.7691

Page 6

Asmbly

Cleaning fluid

Keep plenty of genuine BISSELL 2X formula on hand so you can clean and protect whenever it fits your schedule. Always use genuine BISSELL deep cleaning formulas. Non-BISSELL cleaning solutions may harm the machine and will void the warranty.

WARNING

To reduce the risk of ﬁre and electric shock due to internal component damage, use only BISSELL cleaning ﬂuids intended for use with the deep cleaner.

Professional

Deep Cleaning

Best for

2X Concentrated X X X X

Scotchgard™ Protection

Out cleans

all other formulas

Pet Stain & Odor

Removes tough pet stains and contains

patented odor

removal technology

X X X

Deep Clean

& Protect

Deep cleans carpets

and protects from future stains with

Scotchgard™ Protector

*ONLY BISSELL Protects from future stains with Scotchgard™ Protector

Scotchgard™ is a trademark of 3M®.

Allergen Cleansing Pet Stain PreTreat Stain PreTreat

Helps remove pet &

pollen allergens

Pretreat to help

remove tough pet

stains and odors

Pretreat to

penetrate

and loosen

tough stains

www.BISSELL.com

800.237.7691

Page 7

Operatis

Special features

Innovative cleaning technology

This innovative deep cleaner offers two machines in one. The upright deep cleaner uses brushes and cleaning formula to maximize cleaning. The portable spot cleaner detaches to clean tough spots and stains and hard to reach areas.

Heatwave Technology®

This deep cleaner features Heatwave Technology to help maintain the temperature of the hot tap water you put in it to provide constant heat as you clean. Water in the clean tank is heated by heat from the vacuum motor. The Heatwave Technology automatically turns on when you turn the machine on. Heatwave Technology operates in both upright and portable cleaning modes.

Scotchgard™ Protector

Carpet protection applied at the mill typically wears down over time from heavy foot traffic and everyday cleaning, including deep cleaning. To help restore this important protection, only BISSELL offers deep cleaning formulas with Scotchgard protector. This offers extra protection against dirt and tough stains to keep your carpets looking good longer.

To maintain your carpet’s Scotchgard 5-year limited stain warranty, you do not need to hire a professional. By using your BISSELL deep cleaner with BISSELL 2X formulas containing Scotchgard protector every 12 months, your carpet warranty from 3M remains in effect. No other home deep cleaning system can do this for you. Refer to the Scotchgard Protector warranty for details.

Pedal Graphic

Tip

» For easy carrying, grab the carry handle on the portable spot cleaner and balance with the support handle on the back of the machine.

www.BISSELL.com

800.237.7691

Page 8

Operatis

Before you clean

1. Move furniture to another area if cleaning an entire room (optional).

2. For best results, vacuum area with a dry vacuum cleaner thoroughly before deep cleaning.

3. Pretreating (optional): a . Pretreating is recommended to improve

cleaning effectiveness for heavily soiled carpet in high traffic areas such as entryway and hallways.

b. BISSELL Stain PreTreat Spray the

BISSELL Stain PreTreat formula onto heavy traffic areas, soiled areas or stains.

Allow to penetrate for at least 3 minutes. Clean as normal, using the deep cleaner in

upright mode, following the instructions below.

Upright cleaning mode

Filling formula & water tank

1. Remove tank from the base of the machine by lifting up tank carry handle.

NOTE: This tank was designed with a flat bottom so it can be easily filled.

2. Unscrew the black cap and remove bottle insert.

3. Fill tank with hot (140°F/60°C MAX) tap water to the water fill line. Add two ounces of BISSELL 2X formula to the tank. *Do not boil or microwave.

4. Replace the bottle insert in the tank and tighten the black cap. Replace the tank on the deep cleaner.

ATTENTION

Some Berber carpets have a tendency to fuzz with wear. Repeated strokes in the same area with an ordinary vacuum or deep cleaner may aggravate this condition. Please see Stain Removal instructions on page 11.

3b.

Cleaning

1. Plug into a proper outlet and press the power button.

2. While pressing the trigger, make one slow forward wet pass and another one back.

3. Release the trigger and make one slow forward and backward pass over the same area. Repeated passes will help aid in dry time.

4. Continue passes until cleaning area is complete.

NOTE: Your machine may be equipped with a circuit breaker that will automatically shut off the brush if a large or loose object is caught in the brush roll. If that happens, be sure to unplug your machine, remove the foreign object and then plug the machine back in to reset the circuit breaker.

www.BISSELL.com

800.237.7691

CAUTION

Do not overwet. Take care not to run over loose objects or edges of area rugs. Stalling brush may result in premature belt failure.

» Thorough vacuuming before

Tip

deep cleaning wll prevent early clogging of the lint trap.

Page 9

Operati

Empty dirty tank

1. When the dirty tank reaches the “FULL” line on the tank, it is time to empty.

2. Remove the dirty tank and carry it to a utility sink, toilet or outside (where you will dispose of the dirty water).

3. To unlock the dirty tank lid, rotate the handle over the back of the tank. Remove lid and pour out dirty water. Rinse out the dirty tank to remove any debris.

4. Replace the top of the tank and rotate the handle forward to lock in place on front of tank.

5. Before replacing the tank on the machine, wipe debris from red filter.

Cleaning your machine

1. Flush out machine of any remaining residual solution.

a. Fill the formula & water tank with hot tap

water and turn on your machine.

b. Recline handle and press the spray

trigger for about 15 seconds while making forward and backward passes on carpet. Continue without pressing the trigger until there is no more water being suctioned up.

c . Turn off the machine and wrap the

power cord. Make sure the dirty tank and the formula & water tank are emptied, rinsed, and dried before the next use.

d. Before you replace tank, clean

all debris from red filter screen.

2. Rinse the front nozzle of any dirt and debris. a . Remove the portable spot cleaner from

the base of the machine.

b . Unscrew three screws with Phillips

screw driver and remove nozzle.

c . Rinse the nozzle out at the faucet. d . Place the nozzle back onto the machine

by hooking the tabs into the holes on the bottom sides of the machine. Secure with screws.

WARNING

To reduce the risk of electric shock, turn power switch o and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks.

2b.

www.BISSELL.com

800.237.7691

Page 10

Operatis

Adsdfdd ghg bvh

cvbbj jkn hnbj jkvh

gcghhjj jhffhl kllgh

3. The inside of the end caps can be wiped out with a clean paper towel, or, for a more thorough clean, the end caps can be taken off and rinsed clean.

4. Any loose hair or debris can be pulled from the brush rolls and thrown away. For a more thorough clean, follow directions on page 15 for removal of brush rolls. Your machine is now ready to be stored.

NOTE: Store cleaner in a protected, dry area. Since this product uses water, it must not be stored where there is a danger of freezing. Freezing will damage internal components and void the warranty.

Portable spot cleaning mode

Preparing the machine

1. Step on the portable spot cleaning pedal to release the portable spot cleaner.

2. Release flex hose by twisting the hose secure latch clockwise. Unwrap flex hose completely.

3. Attach the desired tool to the hose grip until it snaps together. Make certain the tool is securely attached.

4. Twist the Quick Release cord wrap clockwise to unwrap the power cord completely and plug cleaner into grounded outlet.

Tip

» For best results, empty, rinse, and dry both tanks before storing. » Let all parts dry completely and replace onto machine.

Filling tank

1. Follow the instructions for filling the tank in the upright cleaning mode section on page 8.

Cleaning with Tools

IMPORTANT! If using to clean upholstery, check upholstery tags. Check manufacturer’s tag before cleaning. “W” or “WS” on the tag means you can use your Lift off Deep Cleaner if the tag is coded with an “X” or an “S”(with a diagonal stripe through it), or says “Dry Clean Only”, do not proceed with any deep cleaning machine. Do not use on velvet or silk. If manufacturer’s tag is missing or not coded, check with your furniture dealer.”)

NOTE: If your deep cleaner came with a Stair Tool or Deep Reach Tool, do not follow cleaning instructions below. Instead, follow instructions in next section.

1. Hold the tool approximately 1” above the soiled surface. Press the spray trigger to apply the cleaning solution to the soiled area.

NOTE: Hold end of hose below the tank water level to help prime the portable spot cleaner.

www.BISSELL.com

800.237.7691

Manufacturer’s tag

Page 11

Operatis

2. Using the brush on the tool, gently scrub the area to be cleaned.

3. Apply downward pressure on the tool and pull it toward you. The suction will remove the dirt and cleaning solution. Continue until no more dirt can be removed.

Cleaning with Deep Reach™ Tool

1. Set tool on soiled surfaces and press the trigger to spray solution onto the soiled area to be cleaned.

2. Slowly move the tool back and forth over the soiled surface, keeping the tool in contact with the carpet.

3.Release trigger and move tool slowly over the soiled area to suction up water and dirt.

4. Continue to clean the area, working in small sections, until no more dirt can be removed.

Cleaning with the 3-in-1 Stair Tool

This versatile 3-way tool sprays, scrubs, and suctions up dirt and stains from the outer curves, corner, and tread of carpet staircase.

1. Twist the tool head to desired setting to clean carpeted stair. The downward facing edge is the active cleaning mode.

a. Use the flat area to clean top of stairs b. Use pointed edge to clean inside crevice c. Use indented area to clean outer corner

(nose) of stairs

2. Ensure the tool spray tip is pointing downward. Pressing trigger, slowly move the tool back and forth over the soiled surface keeping the tool in contact with the carpet.

3. Release trigger and move tool slowly over the soiled area to suction up water and dirt.

4. Continue to clean the area until no more dirt can be removed.

a. b. c.

FLAT

NOSE

CREVICE

www.BISSELL.com

800.237.7691

Page 12

Operatis

Empty dirty tank

Follow the instructions under Empty dirty tank section on page 9 of the Upright cleaning mode section.

Cleaning portable machine

1. Remove and rinse the tools in clean, running water. Dry and replace in the tool storage provided.

2. It is recommended that you suction clean water from a bowl to rinse out the hose. Then lift end of hose and stretch out to ensure all water is cleared from hose.

3. Coil flex hose around the hose wrap and secure with latch.

4. Check suction gate and if it appears dirty, follow steps 1-4 under Cleaning Suction Gate on page 13.

Replacing portable machine on base

1. Align the product with the cord side on the left and hose side on the right.

2. Push down the portable spot cleaner until both sides click securely into place. Test the fit by pulling up on the carry handle to make sure it is secure.

Cord side

Hose side

www.BISSELL.com

800.237.7691

Page 13

Mainnce & Care

Machine care (check regularly)

Cleaning suction gate

The suction gate automatically diverts air when the portable deep cleaner is detached. This should be checked and cleaned regularly for any dirt and debris.

1. Step on the pedal and remove the portable spot cleaner. Remove dirty tank.

2. Remove two screws and pull off suction gate door.

3. Wipe suction gate clean and rinse suction gate door.

4. Replace suction gate door and two screws.

Cleaning spray tips

1. Step on the pedal and remove the portable spot cleaner. To remove each spray tip, push tab in and pull it out.

2. Clean by rinsing under hot water.

3. Replace by snapping back in.

Spray Tips

WARNING

To reduce the risk of electric shock, turn power switch o and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks.

Suction Gate

www.BISSELL.com

800.237.7691

Page 14

Mainnce & Care

Small belt removal and replacement (as needed)

Occasional replacement of one or both belts may become necessary. If that is needed, please follow the instructions below.

1. Turn off the machine and unplug it from the outlet. Remove portable spot cleaner.

2. Remove the nozzle by unscrewing three screws on the nozzle cover.

3. Turn the machine on its side. IMPORTANT: with portable spot cleaning pedal facing down.

4. Remove end cap by unscrewing the 3 screws.

Take care not to drop the screws into the unit.

5. Remove 1 silver screw from the pivot arm.

6. Remove pivot arm by gently lifting up.

7. Remove small brush belt.

8. Replace small brush belt, and reverse

steps above.

9. Manually rotate brushes by hand to make sure they move freely. You may notice a slight resistance from the motor.

WARNING

To reduce the risk of electric shock, turn power switch o and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks.

www.BISSELL.com

800.237.7691

Page 15

Mainnce & Care

Brush removal and large belt replacement (as needed)

Brushes can be removed for cleaning or replacement as needed.

1. Follow small belt removal Instructions on page 14 items 1-7.

2. Remove brush rolls by pulling them off of the metal rods. Be careful not to lose the

small washer at each end of the brush rolls.

3. Re-attach the large belt to the grooves on

the end of the new brush rolls. If the belt is damaged, replace with a new belt.

4. Place cleaned or new brush rolls back onto the rods. Make sure one washer is on each end of the rollers prior to sliding onto the rod. Be sure the brush is seated completely on the rod.

5. Replace small belt over grooves in back roller and metal cog.

6. Replace pivot arm and secure with silver screw.

7. Re-attach end cap by tightening with the (3) black screws.

8. Return front nozzle to front of unit, by latching from underneath and then securing with 3 screws.

9. Follow step number 8 & 9 on page 14. If you have any questions or are having

trouble installing or replacing your belt(s) or brushes, please call BISSELL Consumer Care.

WARNING

To reduce the risk of electric shock, turn power switch o and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks.

www.BISSELL.com

800.237.7691

Page 16

Trbleshting

WARNING

To reduce the risk of electric shock, turn power switch o and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks.

Problem Possible causes Remedies

Heater indicator light does not illuminate

The power is not turned ON The power must be ON to activate

The portable spot cleaner is not attached completely

the heater indicator light

Make sure the portable spot cleaner is attached. Push down firmly to check (see pages 5 or 12 for detailed instructions)

Reduced spray OR no spray

DirtLifter PowerBrush does not turn

Loss of suction power

Formula & water tank may be empty

Formula & water tank may not be seated completely

Pump may have lost prime in portable spot cleaning mode

The portable spot cleaner is not attached completely

The unit is in the upright position Brushes only rotate when unit is

Circuit breaker on machine (if equipped) may have tripped

The belt is off or broken Turn power OFF and unplug unit

Tanks may not be seated properly Pick up both tanks and reseat them

Nozzles may not be assembled properly

The portable spot cleaner is not attached completely

Dirty tank has picked up maximum amount of dirty water and has reached full line

Formula & water tank is empty Check fluid levels in formula & water

Suction Gate is open Check to make sure the suction gate

Refill tank

Turn power OFF. Remove and reseat tank

Hold end of hose below water level in tank to prime

Push down firmly to check connection

Make sure the portable spot cleaner is attached. Push down firmly to check (see pages 5 or 12 for detailed instructions)

reclined using the recline pedal

Turn the machine OFF and unplug from outlet. Check to see if foreign object is caught in brush roll. Remove object. Plug machine in to reset circuit breaker

from outlet. Follow instructions on pages 14 and 15

so it they fit snugly on the unit

Unplug the unit. Check to make sure the "lip" of the nozzle cover is securely hooked into the groove on the top of nozzle (see page 9)

Make sure the portable spot cleaner is attached. Push down firmly to check (see pages 5 or 12 for detailed instructions)

Empty dirty tank

tank

is closed. Follow “Cleaning Suction Gate” instructions on page 13.

www.BISSELL.com

800.237.7691

Page 17

Trbleshting

WARNING

To reduce the risk of electric shock, turn power switch o and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks.

Please do not return this product t o t h e s t o r e .

Other maintenance or service not included in the manual should be performed by an authorized service representative.

Thank you for selecting a BISSELL product.

For any questions or concerns, BISSELL is happy to be of service. Contact us directly at 1-800-237-7691.

Replacement Parts

These items are available for your BISSELL ProHeat Lift-Off deep cleaner. Call 1-800-237-7691 or visit www.BISSELL.com

ParT # ParT name ParT # ParT name

160-0813 Formula & Water Tank Assembly

(includes cap and insert)

203-7894 Collection Tank Bottom 203-7904 Cord Wrap

20 3-7896 End Caps with Edge Brushes

(2 pack, includes screws)

203-6675 Cap and Insert for Formula

& Water Tank

203-7897 Spray Tips Assembly

(includes two spray tips)

203-7906 Nozzle Cover Top w/Gasket 203-7907 Nozzle Cover Lower and

203-6686 Brush Single Pack

(includes 1 brush roll, and 1 axle)

203-6804 Large Brush Belt 203-6689 Hose Secure Latch

203-7918 Dirty Tank Gasket Assembly

(include both gaskets)

*Not all parts are included with every model.

203-6688 Small Brush Belt

203-7917 Diverter Cover Assembly

www.BISSELL.com

Front w/Gasket

(includes cover and screws)

800.237.7691

Page 18

Accessories

These items are available for your BISSELL ProHeat Lift-Off deep cleaner. Call 1-800-237-7691 or visit www.BISSELL.com

ParT # ParT name ParT # ParT name

203-6651 3” Tough Stain Tool

203-6653 4” Upholstery Tool 203-6654 6” Stair Tool

203-7885 Spraying Crevice Tool 203-7412 Deep Reach Pet Tool

203-6652 Powered TurboBrush®

Hand Tool

1603650 3-in-1 Stair Tool 62E5-2 2X Deep Clean & Protect

99K5-2 2X Pet Stain and Odor Formula

with Scotchgard™ Protection 60 oz.

78H6-3 2X Professional Deep Cleaning

Formula with Scotchgard™ Protection 48 oz.

4001 Stain PreTreat 22 oz. 210-3040 Mesh Bag

*Not all parts are included with every model.

Cleaning Formula: Refer to bottom of page 5 of this guide for a full selection of cleaning formula available for purchase.

89Q5-2 2X Allergen Cleansing Formula

0790 Pet Stain PreTreat 22 oz.

Formula with Scotchgard™ Protection 60 oz.

60 oz.

www.BISSELL.com

800.237.7691

Page 19

Warrty Service

This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer Care by E-mail, telephone, or regular mail as described below.

Limited Two-Year Warranty

Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL will repair or replace (with new or remanufactured components or products), at BISSELL’s option, free of charge from the date of purchase by the original purchaser, for two years any defective or malfunctioning part.

See information below on "If your BISSELL product should require service".

This warranty applies to product used for personal, and not commercial or rental service. This warranty does not apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair, or any other use not in accordance with the User's Guide is not covered.

BISSELL IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY

THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE TWO YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.

Some states do not allow limitations on how long an implied warranty last so the above limitation may not apply to you.

NOTE: Please keep your original sales receipt. It provides proof of date of purchase in the event of a warranty claim.

If your BISSELL product should require service:

Contact BISSELL Consumer Care to locate a BISSELL Authorized Service Center in your area.

If you need information about repairs or replacement parts, or if you have questions about your warranty, contact BISSELL Consumer Care.

Website or E-mail:

www.BISSELL.com

Or Call:

BISSELL Consumer Care 1-800-237-7691 Monday – Friday 8am - 10pm ET Saturday 9am - 8pm ET Sunday 10am - 7pm ET

Or Write:

BISSELL Homecare, Inc. PO Box 3606 Grand Rapids, MI 49501 ATTN: Consumer Care

www.BISSELL.com

800.237.7691

Page 20

Regr yr product tod!

Registering is quick, easy and offers you benefits over the lifetime of your product.

BISSELL Rewards Points

Automatically earn points for discounts and free shipping on future purchases.

Faster Service

Supplying your information now saves you time should you need to contact us with questions regarding your product.

You’ll receive:

Product Support Reminders and Alerts

We’ll contact you with any important product maintenance reminders and alerts.

Special Promotions

Optional: Register your email to receive notice of offers, contests, cleaning tips and more!

Visit www.BISSELL.com/registration now!

BISSELL Csumer Care

For information about repairs or replacement parts, or questions about your warranty:

Call:

BISSELL Consumer Care

1-800-237-7691

Monday - Friday 8 am - 10 pm ET Saturday 9 am - 8 pm ET Sunday 10am - 7pm ET

Write:

BISSELL Homecare, Inc. PO Box 3606 Grand Rapids MI 49501 ATTN: Consumer Care

Visit the BISSELL website: www.BISSELL.com

When contacting BISSELL, have model number of cleaner available. Please record your Model Number: ___________________ Please record your Purchase Date: ___________________

NOTE: Please keep your original sales receipt. It provides proof of purchase date in the event of a warranty claim. See Warranty on page 15 for details.

We c’t wait to ar from y!

Rate this product and let us (and millions

of your closest friends) know what you think!

www.BISSELL.com

Scotchgard is a trademark of 3M

Bissell 24A4 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual