Bertazzoni REF30RCPIXR, REF30FCIPIXR, REF30RCPIXL, REF30FCIPIXL, REF30RCPRR Installation Guide

...
0 (0)

Installation guide

Notice d’installation

Guía de instalación

REF18WCPIXL REF24WCPRL REF18WCPIXR REF24WCPRR REF18FCIPIXL REF24FCIPRL REF18FCIPIXR REF24FCIPRR REF18WCPRL REF30RCPIXL REF18WCPRR REF30RCPIXR REF18FCIPRL REF30FCIPIXL REF18FCIPRR REF30FCIPIXR REF24RCPIXL REF30RCPRL REF24RCPIXR REF30RCPRR REF24WCPIXL REF30FCIPRL REF24WCPIXR REF30FCIPRR REF24FCIPIXL REF36RCPIXL REF24FCIPIXR REF36RCPIXR REF24RCPRL REF36RCPRL REF24RCPRR REF36RCPRR

INDEX

EN

1

IMPORTANT INSTRUCTIONS

4

1.1

Important safety instructions.....................................................................................................................................

4

1.2

Children safety................................................................................................................................................................

4

2

TECHNICAL REQUIREMENTS

4

2.1

Appliance features and installation requiremens................................................................................................

4

2.2

Installation cutout features: panel ready................................................................................................................

6

2.3

Installation cutout features: panel installed..........................................................................................................

7

3

PREPARING THE INSTALLATION

8

3.1

Transport to installation site and unpacking.........................................................................................................

8

3.2

Electrical and water connection................................................................................................................................

8

3.3

Energy: Alternatives and Home Automation.........................................................................................................

9

3.4

Levelling...........................................................................................................................................................................

9

4

CUTOUT DIMENSIONS

10

4.1

Cutout dimensions and installation..........................................................................................................................

10

4.2

Flush installation with standard trims....................................................................................................................

10

5

PANELS MOUNTING

11

5.1

Decorative door panel layout......................................................................................................................................

11

5.2

Decorative panel for fridge column..........................................................................................................................

13

5.3

Decorative panels layout for wine column with glass door..............................................................................

14

5.4

Panel dimensions column models...........................................................................................................................

15

5.5

Mounting panels to the door.......................................................................................................................................

16

6

INSTALLATION

18

6.1

Built-in installation of single appliance...................................................................................................................

18

6.2

Built-in installation of two or more appliances.....................................................................................................

18

6.3

Maximum cabinet depth over panel ready appliance with single door panel.............................................

22

7

COMPLETING THE INSTALLATION

23

7.1

Anti-tipping safety assembly......................................................................................................................................

23

7.2

Ventilation........................................................................................................................................................................

24

7.3

Post installation control...............................................................................................................................................

25

7.4

Start up.............................................................................................................................................................................

25

3

1.IMPORTANTINSTRUCTIONS 2. TECHNICAL REQUIREMENTS

1.1 Important safety instruction

Symbols used in the Guide:

Note

Tips for the correct use of the appliance

Important

Directions to avoid appliance damage

Warning

directions to prevent injury

1.2 Children safety

DANGER: Risk of child entrapment. Before you throw away your old refrigerator, freezer or wine cellar:

>Take off the doors

>Leave the shelves in place so that children may not easily climb inside.

Important!

Dimensions in parentheses are in inches.

Weights in parentheses are in pounds.

Temperatures in parentheses are in Fahrenheit degrees.

2.1 Appliance features and installation requirements

 

Appliance

18”

 

 

dimensions

w: 456 mm (17 15/16”)

 

 

panel ready

h: 2120 mm (83 1/2”)

 

 

 

d: 615 mm (24 1/4”)

 

 

 

24”

 

 

 

w: 609 mm (24”)

 

 

 

h: 2120 mm (83 1/2”)

 

 

 

d: 615 mm (24 1/4”)

 

 

 

30”

 

 

 

w: 761 mm (29 15/16”)

 

 

 

h: 2120 mm (83 1/2”)

 

 

 

d: 615 mm (24 1/4”)

 

 

 

36”

 

 

 

w: 913 mm (35 15/16”)

 

 

 

h: 2120 mm (83 1/2”)

 

 

 

d: 615 mm (24 1/4”)

 

 

Appliance

18”

 

 

dimensions

w: 456 mm (17 15/16”)

 

 

stainless

h: 2120 mm (83 1/2”)

 

 

steel clad

d: 620 mm (24 3/8”)

 

 

 

24”

 

 

 

w: 609 mm (24”)

 

 

 

h: 2120 mm (83 1/2”)

 

 

 

d: 620 mm (24 3/8”)

 

 

 

30”

 

 

 

w: 761 mm (29 15/16”)

 

 

 

h: 2120 mm (83 1/2”)

 

 

 

d: 620 mm (24 3/8”)

 

 

 

36”

 

 

 

w: 913 mm (35 15/16”)

 

 

 

h: 2120 mm (83 1/2”)

 

 

 

d: 620 mm (24 3/8”)

 

4

EN

Weight with

18”

packaging

up to 150 kg (331 lb)

 

24”

 

up to 170 kg (375 lb)

 

30”

 

up to 190 kg (419 lb)

 

36”

 

up to 200 kg (441 lb)

Voltage

AC 110 - 120V 60Hz

 

 

Power supply

90° Nema 5-15P

cable

 

Dedicated circuit

15A

breaker

 

Potable water

from 0.05 MPa to 0.5 MPa

supply pressure

(0.5 Bar - 5 Bar)

 

 

PSI measurement

7.25psi - 72.5psi

 

 

Water connection

3/4” NPT (1/4” elbow adap-

 

ter included)

Provided

- Anti tipping kit Z310113

installation

(in all columns panel ready

accessories

and panel installed)

 

 

- Joining strip, white

 

Z310057 (in all columns

 

panel ready and panel

 

installed)

 

- Lateral mounting clips

 

(10 pieces white) Z310129

 

(in all columns panel ready

 

and panel installed)

 

- Customized panels

 

mounting kit, fridge and

 

freezer Z310272 (only in

 

fridge and freezer columns

 

panel ready)

 

- Customized panels

 

mounting kit, wine cellar

 

Z310273 (only in wine co-

 

lumns panel ready)

 

- Central connection kit , for

 

panel ready models com-

 

bined installation Z310293

 

(only in freezer and wine

 

columns panel ready)

 

- Central connection kit,

 

for panel installed mo-

 

dels combined installation

 

Z310287 (only in freezer

 

and wine columns panel

 

installed)

 

- Water connection kit

 

Z310300 (only in freezer

 

columns panel ready and

 

panel installed)

 

- 4 mm (1/8”) allen wrench

 

(in all columns panel ready

 

and panel installed)

 

 

Additional

- Phillips head screwdriver

equipment

- wood drill

necessary

- 2.5 mm (1/8”) bit for wood

 

 

- 8 mm (3/8”) bit for walls

 

- 10 mm (3/8”) bit for walls

 

- 17 mm (11/16”) wrench

 

- 19 mm (3/4”) wrench

 

 

Others provided

- Cleaning kit Z310284

accessories

(in all columns panel ready

 

and panel installed)

5

2. TECHNICAL REQUIREMENTS

2.2 Installation cutout features: panel ready

A - area to be left clear for the anti-tipping brackets

Minimum cutout Height

2130 mm (83 7/8”)

Minimum cutout Width

36”: 914 mm (36”) 30”: 762 mm (30”) 24”: 610 mm (24”) 18”: 457 mm (18”)

Minimum cutout Depth

615 mm (24 1/4”) + panel thickness for flush install

Door hinges do not lock at 90°

Door Swing Clearance

36”: 1489 mm (58 5/8”) 30”: 1338 mm (52 5/8”) 24”: 1187 mm (46 3/4”) 18: 1036 mm (40 3/4”)

Door Opening Angle

100°

Width

36”: 913 mm (35 15/16”) 30”: 913 mm (29 15/16”) 24”: 609 mm (24”)

18”: 456 mm (17 15/16”)

Height

2120 mm (83 1/2”) + 25 mm (1”)

Depth with door (without panel)

615 mm (24 1/4”)

Minimum distance from the wall (hinge side)

36”: 158 mm (6 1/4”) 30”: 132 mm (5 1/4”) 24”: 108 mm (4 1/4””) 18”: 82 mm (3 1/4”)

 

<![if ! IE]>

<![endif]>(3 1/2")

127 mm (5")

127 mm (5")

<![if ! IE]>

<![endif]>(3 1/2")

 

<![if ! IE]>

<![endif]>mm

<![if ! IE]>

<![endif]>mm

 

 

 

 

 

<![if ! IE]>

<![endif]>82

A

A

 

<![if ! IE]>

<![endif]>82

<![if ! IE]>

<![endif]>”)

 

36":914 (36”)

 

 

 

<![if ! IE]>

<![endif]>(83

 

 

 

 

 

 

 

 

 

<![if ! IE]>

<![endif]>min 2130

 

30": 762 (30”)

 

 

 

24": 610 (24”)

 

 

 

 

 

 

 

 

18": 457 (18”)

 

 

 

 

 

 

615 (24 ¼”)

 

 

 

 

565 (22 ¼” )

<![if ! IE]>

<![endif]>½”) +25 (1”)

<![if ! IE]>

<![endif]>¼” )

 

<![if ! IE]>

<![endif]>2120 (83

<![if ! IE]>

<![endif]>1808 (71

 

 

<![if ! IE]>

<![endif]>+25 (1”)

<![if ! IE]>

<![endif]>233(9¼”) + 25 (1”)

505 (19 ¾”)

<![if ! IE]>

<![endif]>⅛”)

 

 

<![if ! IE]>

<![endif]>231(9

 

<![if ! IE]>

<![endif]>615 (24 ¼") 565 (22 ¼")

36": 913 (35 15⁄16") 30": 761 (29 15⁄16")

24": 609 (24") 18": 456 (17 15⁄16")

 

 

 

 

36": 158 (6 ¼")

 

 

 

 

30": 132 (5 ¼" )

<![if ! IE]>

<![endif]>⅝") ⅝")

<![if ! IE]>

<![endif]>¾")

<![if ! IE]>

<![endif]>¾")

24": 108 (4 ¼")

18": 82 (3 ¼")

<![if ! IE]>

<![endif]>(58

<![if ! IE]>

<![endif]>(52

<![if ! IE]>

<![endif]>(46

<![if ! IE]>

<![endif]>(40

 

<![if ! IE]>

<![endif]>36": 1489

<![if ! IE]>

<![endif]>30": 1338

<![if ! IE]>

<![endif]>24": 1187

<![if ! IE]>

<![endif]>18": 1036

100°

 

6

2.3 Installation cutout features: panel installed

A - area to be left clear for the anti-tipping brackets

Minimum Cutout Height

2130 mm (83 7/8”)

Minimum Cutout Width

36”: 914 mm (36”) 30”: 762 mm (30”) 24”: 610 mm (24”) 18”: 457 mm (18”)

Minimum Cutout Depth

635 mm (25”)

Door hinges do not lock at 90°

Door Swing Clearance

36”: 1487 mm (58 1/2”) 30”: 1336 mm (52 5/8”) 24”: 1185 mm (46 5/8”) 18”: 1034 mm (40 3/4”)

Door Opening Angle

100°

Width

36”: 913 mm (35 15/16”) 30”: 761 mm (29 15/16”) 24”: 609 mm (24”)

18”: 456 mm (17 15/16”)

Height

2120 mm (83 1/2”) + 25 mm (1”)

Depth with door

620 mm (24 3/8”)

Minimum distance from the wall (hinge side)

36”: 139 mm (5 1/2””) 30”: 103 mm (4 1/8”) 24”: 89 mm (25”)

18”: 63 mm (2 1/2”)

EN

 

<![if ! IE]>

<![endif]>(3 1/2")

127 mm (5")

127 mm (5")

<![if ! IE]>

<![endif]>(3 1/2")

 

<![if ! IE]>

<![endif]>mm

<![if ! IE]>

<![endif]>mm

 

 

 

 

<![if ! IE]>

<![endif]>82

A

A

<![if ! IE]>

<![endif]>82

<![if ! IE]>

<![endif]>”)

 

36":914 (36”)

 

 

<![if ! IE]>

<![endif]>(83

 

 

 

 

 

 

 

<![if ! IE]>

<![endif]>min 2130

 

30": 762 (30”)

 

 

24": 610 (24”)

 

 

 

 

 

 

18": 457 (18”)

 

0F

<![if ! IE]>

<![endif]>2120 (83 ½”) +25 (1”)

620 (24 ⅜” )

 

565 (22 ¼” )

 

 

<![if ! IE]>

<![endif]>1904 (75”)

672 (26 ½”)

<![if ! IE]>

<![endif]>146 (5 ¾”) + 25(1”)

<![if ! IE]>

<![endif]>620 (24 ⅜”) 565 (22 ¼”)

 

<![if ! IE]>

<![endif]>55(3 ⅛”)

<![if ! IE]>

<![endif]>58(2 ¼”)

36": 913 mm (35

15⁄16")

30": 761 mm (29 15⁄16") 24": 609 mm (24")

18": 456 mm (17 15⁄16")

 

 

 

 

36": 139 (5 ½”)

 

 

 

 

30": 103 (4 ⅛”)

<![if ! IE]>

<![endif]>½”) ⅝”) ⅝”) ¾’’)

24": 89 (3 ½”)

18": 63 (2 ½”)

<![if ! IE]>

<![endif]>(58

<![if ! IE]>

<![endif]>(52

<![if ! IE]>

<![endif]>(46

<![if ! IE]>

<![endif]>(40

100°

<![if ! IE]>

<![endif]>36": 1487

<![if ! IE]>

<![endif]>30": 1336

<![if ! IE]>

<![endif]>24": 1185

<![if ! IE]>

<![endif]>18": 1034

 

 

 

 

 

7

Ice Maker

3. PREPARING THE INSTALLATION

3.1 Transport to installation site and unpacking

The appliance is very heavy.

Take maximum care during handling to avoid injury.

The appliance should always be transported in an erect position.

Avoid at all costs leaning it on its front side.

2

4

1

1

3

 

Since this is a large and heavy appliance, before transporting the appliance, check the access to the location where it will be installed (door size, maneuvering space in stairwells, etc.).

The appliance is attached to the base of the packaging (pallet) through four bolts which can be removed using a 19 mm (3/4”) wrench.

It is recommended to use a manual transporting device to move the appliance to the installation site, and only at this point to remove the base of the packaging. The appliance should always be transported in an erect position.

If this is not possible, transport the appliance laying on its rear side.

Once at the installation site, the appliance, which is equipped with four wheels, can be taken off the pallet and positioned in the installation area.

Operate as follows:

>Take off the four bolts securing [ 1 ] the appliance to thepalletbymeansofa19mm(3/4”)wrenchorsocket.

>Remove the fixing brackets [ 3 ] and [ 4 ] .

>To release the front fixing bracket [ 3 ] , unscrew the rear wheel adjusting bolt [ 2 ] by means of a 13 mm (1/2”) wrench or socket. Avoid straining this bolt at its stop points one way or the other so as to not damage the rear leveling system.

Ensure the front leveling legs are retracted so that all 4 wheels are able to contact the floor for easiest maneuvering.

>From the back of the unit and by means of a suitable, high duty hand trolley, take off the appliance and place it on the floor.

Be very careful to avoid any damage to floors. Delicate floors should be protected with plywood, hard cardboard or similar material panels.

3.2 Electrical and water connection

The Built-in filter cannot make it safe to drink any water which is not suitable for human consumption.

The appliance should be connected only to a potable water supply system.

Do not use extension cords or adapters. Once the appliance is fully installed, connected to the water supply (if applicable) and operational, in the event that the water supply must be turned off, (touch the button on control panel to disable the ice maker) before the main water is shut off to prevent the appliance from entering a ‘NO WATER IN’ alarm state.

E

W

E

W

E W

 

E W E W

E W

ELECTICAL&WATER

CONNECTION

W E

W E

The appliances are delivered from the factory for operation at 110V-120V AC - 60Hz (US and Canada). They are provided with a suitable supply cable and plug to be connected to an appropriate 15A socket providing an effective grounding.

A dedicated 15A circuit breaker should also be installed and should be easily accessible so that it can be easily switched off before performing any installation or maintenance.

To connect to the water supply system (for appliances equipped with ice makers) a 1/4” waterline with accessible shut-off valve must be supplied.

The appliance is provided with a water adapter elbow which is suitable for the recommended water pressure and complies the applicable food and water regulations.

The water filter cartridge, which is provided with the appliance, should be installed according to the accompanying instructions. Please refer to water filter installation instructions contained in the water filter kit. The solenoid connection on the appliance is 3/4” diameter but is metric threaded (NPT). A standard

8

garden hose threaded connector such as a braided stainless hose found at typical hardware stores will strip or damage the solenoid threads. It is recommended to use only the supplied 1/4” quick connect elbow adapter for connecting a 1/4” copper or polyethylene source water line to the appliance.

Do not use extension cords and/or multiple adapters for the power supply connection.

ELECTRICAL AND WATER SUPPLY BEHIND THE UNIT

E

W

3.3 Energy: Alternatives and Home Automation

If energy is supplied through an alternative energy power source (solar, geothermal, etc..) or if home automation systems are installed with carrier signals in the power lines, it may be necessary to install an isolation transformer (not supplied) to prevent interference with the appliance’s electronics.

Electrical connection

Water connection

fig.1 Back of appliance

EN

Operate as follows:

>Unwind the electric cable and connect it directly to the wall socket.

>Make sure the appliance is in the Stand-by condition and that all lights are off; should it be not so press the Unit button to switch it off.

>Connect the water cable behind the appliance [ 1 ].

1

3.4 Levelling

Adjust the appliance level by means of the front levelling feet and the rear adjustable wheels.

2

2

1

1

 

Operate as follows:

> If necessary, remove the bottom plinth or grille

(it is kept in position by magnets), adjust the height of the levelling feet [ 1 ] by means of a 17 mm (11/16”) wrench.

>Then adjust the height of the rear wheels by turning the front adjusting bolts [ 2 ] clockwise (raise) or counter-clockwise as it may be required.

Take care if using a power driver for this and lower the clutch to prevent damaging the leveling mechanism.

>Remount the bottom plinth or grille.

9

Bertazzoni REF30RCPIXR, REF30FCIPIXR, REF30RCPIXL, REF30FCIPIXL, REF30RCPRR Installation Guide

4. CUTOUT DIMENSIONS

 

 

 

 

4.1 Cutout dimensions and installation

4.2 Flush installation with standard

 

 

trims

36": 914 (36”)

30": 762 (30”)

24": 610 (24”)

18": 457 (18”)

Series

Cutout width

Panel Width

36”

914 (36”)

908 (35 3/4”)

30”

762 (30”)

756 (29 3/4”)

24”

610 (24”)

604 (23 3/4”)

18”

457 (18”)

451 (17 3/4”)

A

A - KCLITU: Lateral connection Kit (included)

Cutout dimension for combined installation

A B

 

 

 

A

 

 

 

 

 

 

 

 

 

 

18”

24”

30”

36”

 

 

 

 

 

 

B

18”

36”(914mm)

42”(1067mm)

48”(1220mm)

54”(1372mm)

 

 

 

 

 

 

24”

42”(1067mm)

48”(1220mm)

54”(1372mm)

60”(1520mm)

 

 

 

 

 

 

 

30”

48”(1220mm)

54”(1372mm)

60”(1520mm)

66”(1676mm)

 

 

 

 

 

 

 

36”

54”(1372mm)

60”(1524mm)

66”(1676mm)

72”(1829mm)

 

 

 

 

 

 

10

5. PANELS MOUNTING

EN

5.1 Decorative door panel layout

The dimensions of the panels are indicated in the table and drawings on subsequent pages. Nevertheless, according to the requirements for aligning with other kitchen structures, the door panel can be higher than the upper edge of the refrigerator door.

The panels must be mounted using special brackets which attach to adjustable devices provided on the door and drawer and with brackets that anchor and adjust the panel’s vertical direction.

Brackets and fixing screws are provided with the appliance and must be applied to the panel as indicated.

Operate as follows:

To prepare the panels to be mounted on the appliance, follow these steps, working on the back of the panel.

Door Panel

> Draw a vertical center line on the panel from top to bottom [ 1 ].

1

> Starting from the bottom edge of the panel, mark the positioning of the brackets [ 2 ].

> Following the corresponding table, mark the external and then the internal hole [ 3 ].

3

> Position the brackets on each set of marks to make sure they are aligned [ 4 ], if you choose to drill small pilot holes for the screws pay special attention to not pass through the panel entirely.

[ 5 ].

4

5

> Screw the brackets in place [ 6 ].

6

2

11

5. PANELS MOUNTING

> Prepare the appliance door for panel mounting by threading the shoulder bolts into the recessed receivers and the set screws into the other hole [ 7 ]. Ensure the end with the hex key socket is threaded into the door and not on the visible end. Thread this in far enough that it is flush with appliance door face so as not to interferece with hanging the panel. You will adjust these later.

7

12

EN

5.2 Decorative panel for fridge column

 

36”

30”

24”

18”

 

 

 

 

 

A

908 (35 3/4”)

756 (29 3/4”)

604 (23 3/4”)

451 (17 3/4”)

 

 

 

 

 

B

418 (16 1/2”)

343 (13 1/2”)

275 (10 7/8”)

200 (7 7/8”)

 

 

 

 

 

 

 

 

 

 

Holes positions:

 

 

 

 

 

 

A

 

 

 

 

 

 

B

 

B

 

 

 

 

 

6,5 (¼)

6,5 (¼”)

 

 

<![if ! IE]>

<![endif]>¼”)

<![if ! IE]>

<![endif]>)

<![if ! IE]>

<![endif]>”⁄)

 

 

 

 

 

<![if ! IE]>

<![endif]>(6½”

34 (1

⁄ ”)

34 (1 ⁄ ”)

 

 

 

 

 

 

<![if ! IE]>

<![endif]>(50”)

<![if ! IE]>

<![endif]>690,5 (27

<![if ! IE]>

<![endif]>165

<![if ! IE]>

<![endif]>112 (4

 

 

 

<![if ! IE]>

<![endif]>1797 (70 ¾”)

<![if ! IE]>

<![endif]>1271,5

 

 

 

 

 

<![if ! IE]>

<![endif]>min 1929 (75 ”)

13

5. PANELS MOUNTING

5.3 Decorative panels layout for wine column with glass door

 

24”

18”

 

 

 

A

604 (23 3/4”)

451 (17 3/4”)

 

 

 

B

275 (10 7/8”)

200 (7 7/8”)

 

 

 

Door window dimensions:

Holes positions:

 

 

 

 

 

 

 

A

 

 

 

 

 

 

 

B

 

B

 

 

 

 

 

 

6,5 (¼)

6,5 (¼”)

200

 

 

<![if ! IE]>

<![endif]>¼”)

<![if ! IE]>

<![endif]>½”(6 )

<![if ! IE]>

<![endif]>”⁄)

 

 

 

(7 ⁄ ”)

 

 

34 (1

⁄ ”)

34 (1 ⁄ ”)

 

 

 

 

 

<![if ! IE]>

<![endif]>1572 (62”)

<![if ! IE]>

<![endif]>¾”)

<![if ! IE]>

<![endif]>1271,5 (50”)

<![if ! IE]>

<![endif]>690,5 (27

<![if ! IE]>

<![endif]>165

<![if ! IE]>

<![endif]>112 (4

 

 

 

 

<![if ! IE]>

<![endif]>(70

 

 

 

 

 

 

 

599: 327 (12 ⁄ ”)

<![if ! IE]>

<![endif]>1797

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

449: 177 (6 ⁄ ”)

 

 

 

 

 

 

 

 

139 (5 ½”)

139 (5 ½”)

 

 

 

 

 

 

 

<![if ! IE]>

<![endif]>min 1929 (75 ”)

14

EN

5.4 Panel dimensions column models

Panels with width ranging between 19 mm (3/4 ”) and 28 mm (1 1/8 ”). Door panels with weight max of 34 kg (75 lb)

Exceeding these weights could void your warranty for any service issues which can be attributed to overweight panels.

The hinging mechanism on Bertazzoni appliances is considered to be `Zero-clearance`. The door and drawer widths specified below assume the minimum cutout width is being used and a 3.5mm (1/8”) reveal is desired around the panels. Adjust your panel dimensions accordingly to your own design criteria considering your cutout width and your reveal. Minimum reveal / gap should not be less than 1.5mm (1/16”).

SERIES

DOOR WIDTH A

DOOR GLASS WINDOW WIDTH B

 

 

 

36”

908 (35 3/4”)

-

30”

756 (29 3/4”)

-

24”

604 (23 3/4”)

327 (12 7/8”)

18”

451 (17 3/4”)

177 (6 7/8”)

<![if ! IE]>

<![endif]>2120 (83 7/16") + 25 (1")

<![if ! IE]>

<![endif]>min 1929 (75 ) max 2027 (79 ¾”)

 

 

<![if ! IE]>

<![endif]>100 (3 ”⁄)

A

 

<![if ! IE]>

<![endif]>min

For fridge and freezer columns

139

139

(5 ½”)

(5 ½”)

 

<![if ! IE]>

<![endif]>1572 (62”)

 

B

For wine columns

15

5. PANELS MOUNTING

5.5 Mounting panels to the door

Once all brackets and small brackets have been applied to the panels, you can begin installing the bottom drawer.

> Hook the panel to the fixing devices starting from the top aligning brackets [ 6 ].

6

8

7

> At this point, alignment between the panel and adjacent cabinets can be adjusted using the alignment brackets and small brackets [ 7 ] and [ 8 ].

9

> Vertical alignment: tighten or loosen the screw in the brackets to raise or lower the panel [ 9 ].

16

EN

> Depth alignment: working from the inside of the door, after lifting up the magnetic seal on the handle side and rotating the plastic covers on the hinge side, adjust the panel position in the Z-direction by adjusting the shoulder bolts and setscrews with the 4mm hex key in conjunction with each other finally locking each mounting position in place. [ 10 & 11 ].

10

11

Once the front panel has been adjusted, check that the gasket has been repositioned correctly to assure the door/drawer are closing correctly and avoid operational errors of the unit.

The product handle is not included in the appliace packaging, but it has to be bought separately. For handle installation, please refer to the instruction included in handle’s package.

17

6. INSTALLATION

IMPORTANT: The following instruction for installation apply to all Bertazzoni models.

6.1 Built-in installation of single appliance

For a built-in installation, to cover gaps between the appliance and the adjacent cabinets, special side profiles and covering frames are already factory installed.

Operate as follows:

> Push the appliance into the installation cutout [ 1 ].

1

>Always mount front panel on door before pushing the unit into its final position inside the cutout or structure.

>Check the levelling of the appliance, adjusting its feet and wheels to correct it.

>Secure the appliance to the adjacent cabinets by fixing to these the side profiles factory-installed on the appliance [ 2 ].

To make this operation easier keep the door open.

2

3

Side profiles mounting:

Appliance

A

B

B

Wall or furniture

A plastic connecting brackets

B Profile trim cover

6.2 Built-in installation of two or more appliances

> The central profile is provide with freezer and wine cellar columns.

Special side profiles and plastic covering frames are provided for closing gaps between the appliance and the adjacent cabinets.

Operate as follows:

> Position the appliances in front of the installation area, leaving enugh space to operate at their back

[ 1 ].

1

> Mount the profiles the trim covers: first insert them laterally and then push firmly until a “click” is heard [ 3 ].

18

> Access the back of the appliances to mount the joining brackets: fix one side of the top and lower brackets to one of the appliances and subsequently to the other [ 2 ].

2

IMPORTANT: the appliances must be level with one another.

1 – Attach both units to each other at the front using the 5 white plastic brackets to hold the units together.

2 – Adjust the units in the back, so that the side panels are perfectly parallel to each other. There are visual cues that will aid with alignment.

3 – The gap ( C ) between the units must be the same at the back and top. Measure the gap on all edges and adjust if not equal.

EN

4 – Once the gap is consistent on all edges, secure the brackets. If the gap between the units is not even, doors will not align properly.

Gap measurements vary according to the types of units installed. Please refer to the table below for correct gap measurements.

C

A

B

C

19

6. INSTALLATION

Distance between units (A+B)

 

 

 

 

A

 

C

18”

24”

 

30”

36”

 

 

 

 

 

 

 

 

 

 

 

18”

7/8” (22 mm)

15/16” (23,5 mm)

 

1” (24,5 mm)

1” (25,5 mm)

 

 

 

 

 

 

 

 

24”

15/16” (23,5 mm)

1” (25 mm)

 

1” (26 mm)

1 1/16” (27 mm)

B

 

 

 

 

 

 

30”

1” (24,5 mm)

1” (26 mm)

 

1 1/16” (27 mm)

1 1/8” (28 mm)

 

 

 

 

 

 

 

 

 

 

36”

1” (25,5 mm)

1 1/16” (27 mm)

 

1 1/8” (28 mm)

1 1/8” (29 mm)

 

 

 

 

 

 

 

Once the appliances have been adjusted and properly levelled, loosen the two screws holding the sealing plate in position.

Lower the plate until flush with the floor, and retighten the screws. This will ensure optimized airflow through the condenser necessary for proper operation.

> Next join them at the front attaching the plastic connecting brackets with the supplied screws [ 3 ] . Attach the bracket on top of the units (if applicable) as per figure [ 4 ].

3

4

20

> Finish off by mounting the central profile cover onto the central profiles, by pushing it until a click is heard [ 5 ].

5

EN

> Mount the covering frames onto the profiles, first insert them laterally and then push firmly until a “click” is heard [ 8 ].

>Once completed, push the units into their final position [ 6 ].

Always mount front panels on door before pushing the unit into its final position inside the cutout or structure.

>Check the levelling of the appliance, adjusting its feet and wheels to correct it.

>Secure the appliance to the adjacent cabinets by fixing to these the side profiles trims factory-in- stalled on the appliance [ 7 ]. To make this operation easier keep the door open.

6

Take care as appliances will be frontheavy and may tip before they are secured to the adjacent furniture.

21

6. INSTALLATION

Side and central profiles mounting:

Appliance

A

A

A

A

 

 

B C B

Wall or furniture

A - plastic connecting brackets

B - Profile trim cover (side)

C - Profile trim cover (central).

6.3 Maximum cabinet depth over panel ready appliance with single door panel

It is possible that the design of the kitchen and,

 

in particular, of the cutout where the panel ready

 

appliance is going to be fitted includes a cabinet

 

right above the refrigerator itself that must be

 

closed with the same panel mounted on the Panel

 

ready refrigerator door.”

 

In this case, the depth of the cabinet above the

1

appliance must not exceed the depth of the

 

appliance without the door [ 1 ].

 

This will allow the panel attached to the refrigerator door to open correctly without interference during its rotation up to 100°.

7/8”) (1 47mm

22

7.COMPLETINGTHEINSTALLATION

EN

7.1 Anti-tipping safety assembly

If the appliance(s) is not connected through the side profile trims to secured cabinetry you must install the anti-tip brackets to ensure the product does not fall forward during use and cause damage or injury. Failing to secure the appliance(s) securely will void any warranty claim attributable to a tipping situation.

Operate as follows:

> The brackets should be applied as illustrated using the provided screws If using the anti-tip brackets, lag into wood framing or concrete - drywall will not hold the weight of appliance.

Place a bracket on the top of the appliance in correspondence to the fixing holes and against the wall

[ 1 ].

1

(1

”)

 

<![if ! IE]>

<![endif]>”)

 

 

 

 

 

 

<![if ! IE]>

<![endif]>59 (2

 

 

> Mark up the holes position on the wall [ 2 ].

2

> Drill the wall with an 8 mm (3/8”) bit and insert the expansion plug [ 3 ].

3

> Reposition the bracket and fix it first to the cabinet and then to the wall [ 4 ].

4

In order to use the anti-tip brackets on the top compressor models, it will be necessary to temporarily remove the top, metal ceiling / shield to access the bolting points for the brackets./ shield to access the bolting points for the brackets.

23

Loading...
+ 53 hidden pages