Bertazzoni REF30PIXL User Manual

0 (0)

REF30PIXL

REF30PIXR

REF30PRL

REF30PRR

REF36PIXL

REF36PIXR

REF36PRL

REF36PRR

USER MANUAL

EN

MODE D’EMPLOI

FR

Index

Page 3 1 Important directions for safety and the environment

1.1For your safety

1.2Caring for the environment

1.3Cleaning, sanitization and maintenance of the ice and/or water dispenser (if present)

42 Installation

2.1Installation

2.2Connection to the electrical power supply

2.3Connection to the water system

53 Before starting

3.1Know your appliance

3.2Main features

3.3Main components

3.4Electronic Control

3.5Main control panel

104 Appliance switching on and off

4.1Switching on and off

4.2How to adjust the temperature for different requirements

4.3Ice Maker activation

4.4Information and malfunction messages on the display

125 Settings and Special Functions

5.1Customization and language settings

5.2Special functions activated through the Menu

5.3Basic settings of the Menu

176 Internal Layout

6.1Internal Layout (positioning, adjustment, removal)

197 Activation and use of the Ice Maker

7.1Activation and use of the Ice Maker

7.2Water Filter

218 Lighting

8.1Lighting

229 Food Preservation

9.1General directions

9.2How to maintain good food quality

9.3Recommendations for preserving fresh food

9.4Recommendations for preserving frozen food

10 Recommended times for food preservation

26

11Care and Cleaning

27 11.1 Care and Cleaning

11.2 Condenser cleaning

11.3 Internal cleaning

12Troubleshooting Guide

28 12.1 Troubleshooting Guide

12.2 Malfunction messages appearing on the display

14 Menu Map

3014.1 Functions

3114.2 Setting

English

Français

1

2

Important directions for safety and the environment

1

Risk Group 2

PRUDENZA:

NON FISSARE LA LAMPADA IN FUNZIONE.

PUÒ ESSERE DANNOSO PER GLI OCCHI.

CAUTION:

DO NOT STARE AT OPERATING LAMP.

MAY BE HARMFUL TO THE EYES.

Product tested in accordante with EN62471

B09001301

Notes

Recommendations for correct use of the appliance

For your safety 1.1

If this appliance is replacing an existing appliance which must be removed or disposed of, make sure that it does not become a dangerous trap for children by cutting its power supply cable and rendering it impossible to close the door. Use the same caution at the end of the lifespan of the new appliance.

This appliance is designed to refrigerate beverages and foods and is intended for domestic use.

The appliance must be installed by following the instructions in the Installation Guide, particular care should be taken not to obstruct the vent openings of the appliance and of the built-in units.

The appliance features a concentrated lighting system with LED lamps. Do not stare into these lamps when they are on to avoid possible eyesight damage.

This warning is also contained on the label attached to the inside of the refrigerator door.

When the freezer is functioning do not touch the inner surfaces in stainless steel with wet or damp hands, since skin may stick to the very cold surfaces.

Do not use any type of electrical equipment inside of the food conservation compartments.

When positioning the shelves, do not place fingers in the shelf slide guides.

English

Important

Directions for avoiding appliance damage

Warning

Indications for avoiding injury to people

Do not position containers of flammable liquids near the appliance.

Completely switch off the appliance and unplug the power supply cable during cleaning operations. If the plug is not easily reached, it is a good idea to turn off the breaker or remove the fuse that controls the socket that the appliance is connected to.

The packaging parts can be dangerous for children: do not allow children to play with the plastic bags, plastic film or Styrofoam.

Any repairs must be performed by a qualified Service technician.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

Do not damage the appliance refrigerant circuit pipes.

Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.

Français

3

1

1.2

Important directions for safety and the environment

Caring for the environment

Pay special attention to correct disposal procedure for all the packaging materials.

The appliance must not be disposed of with urban waste. Contact local waste disposal centers for on how to dispose of recyclable waste.

Prior to disposal, cut the power supply cord and make it impossible to close the door.

During disposal, avoid damage to the refrigeration circuit.

The appliance does not contain hazardous substances for the atmospheric ozone layer, neither in the refrigeration circuit nor in the insulation.

1.3 Cleaning, sanitization and maintenance of the ice and/or water dispenser (if present)

Failure to follow the instructions regarding sanitizing can compromise the hygienic safety of the water dispensed.

When using the appliance for the first time and every time the filter is changed, it is recommended to let the water flow in the circuit using the “Manual Cleaning” and discard the ice produced in the first 24 hours.

If the water dispenser has not been used for more than 4/5 days, it is advisable to clean the circuit and run off the first litre of water.

Reposition the removable water dispenser (if present), ensuring your hands are hygienically clean.

Clean the ice bucket or drawer regularly but using only drinking water.

The filter must be changed when indicated on the control panel or when the ice/water dispenser has not been used for more than 30 days.

With each filter replacement, sanitise the ice and/or water distribution system using a food grade disinfectant (with sodium hypochlorite), which does not alter the characteristics of the materials, or use the “Sanitising Kit” available from the After-Sales Service. Rinse with at least 2 litres of water before use.

Only original spare parts supplied by the manufacturer should be used when replacing components in the ice and water dispenser.

Any work on the appliance must be carried out by a qualified tech - nician or the After-sales Service.

4

Do not use extension cords and/or multiple adapters for the power supply connection.

DO NOT connect the refrigerator to any GFCI receptacle.

Installation 2

Installation 2.1

Make sure that installation is performed correctly, adhering to all directions in the specific installation manual provided with the appliance.

Connection to the electrical power supply 2.2

The appliance operates at 115 V AC, 60 Hz and is equipped with a power supply cord with a 3-prong grounded plug, which must be connected to a corresponding 3-prong (15 Amp) grounding-type wall receptacle.

English

Français

5

2 Installation

2.3Connection to the water system

The models provided with Ice Maker require a connection to the domestic water supply system. This can be executed through the 1/4” water line (copper or polyethylene)to the house water supply. The system pressure must be between from 8 psi to 75 psi (between 0.5 bar and 5 bar).

Different pressures can cause malfunctions or leaks in the water system. The appliance should be supplied only with drinkable water. Refer to the installation manual for the water connection.

The appliance should be supplied only with drinkable water.

Make sure that installation is performed correctly, according to all of the directions in the specific installation manual provided with the appliance.

Do not attempt to use a locally sourced garden hose threaded adapter or braided supply line. It will strip the threads on the appliance water connection solenoid.

6

Before starting

3

 

 

Know your appliance

3.1

 

 

The refrigeration system and the efficient separation of internal compartments ensures maximum freshness and offers excellent conservation of foods in the three compartments: refrigerator, Fresco and freezer

It is also possible, should there be a need, to further increase the flexibility of the appliance by making the freezer compartment operate as a refrigerator or as a Fresco compartment

The Fresco compartment has a low temperature and controlled humidity, providing excellent conservation in superior preservation conditions for fresh foods

Electronic control guarantees constant temperature and humidity levels set by the user and provides real-time compartment temperature readings.

An interactive menu (Menu) allows customized management of appliance functions and the visualization of functioning messages

Power save features to reduce consumption during vacation periods

Congratulationsforhavingpurchasedyournewrefigerator: from now on you can use our innovative conservation system, which will allow you to keep all of your food in the best way possible.

This manual will answer most of your questions about the product’s features. Should you require further information, please check our website

http://us.bertazzoni.com/care-service

or write us an e-mail at

aftersaleservice@bertazzoni.com

Before calling, write down the model type and serial number which are available on the warranty certificate and on the rating plate located on the bottom left-hand corner of the appliance, behind the bottom drawer and any messages which may have appeared on the display.

Main features 3.2

Ample drawer space with Soft self-closing systems in the Fresco area

Ice Maker for automatic ice production of variable cube size

Easily replaceable water filter located inside the refrigerator

Patented adjustable shelf system, with shelves that can be positioned at any level inside of the refrigerator without having to be removed

Stainless steel surface both inside and outside, with fine aluminum trim

Patented hinge system that permits automatic door closing

External drawers with to self-closing system

Localized lighting with LEDs

Anti-tipping system by means of wall mounting brackets

English

Français

7

3 Before starting

3.3Main components

Fridge

Low Temp

TriAction

1

 

2

10

3

11

4

12

 

 

13

7

 

 

14

8

 

 

15

 

16

9

 

Single drawer Fridge

1 Stainless steel structure with aluminum trim

2 Control panel with Menu

3 Water Filter

4 Patented shelf positioning system

5 Control panel, Fresco area

6 Fresco compartment with controlled humidity

7 “Low Temp” drawer with controlled humidity

8 Automatic icemaker

9 Double refrigeration system

10 Temperature display

11 Sound signals

12 Vacation function

13 Spacious door shelves

14 Innovative lighting

15 Automatic door and drawer closure

16 Frezer compartment that can be transformed into a refrigerator or Fresco compartment

(TriAction function)

8

Before starting

3

Electronic Control

3.4

The innovative electronic control system maintains constant temperature in multiple compartments and displays it on the control panel. It also allows user interaction making it possible to personalize settings of various functions and to alert the user with sound and/or visual messages should any malfunction occur in the appliance.

Main control panel 3.5

UNIT

FRIDGE

ENTER

ICE MAKER

 

1

2

3

1

Unit

 

 

2

Fridge

 

3

Menu

 

 

4

Up/down

 

Fridge

 

 

 

5

Display

 

 

Up/Down

 

6

Freezer

 

 

(TriAction)

 

7

Enter

 

 

8

Ice maker

 

9

Alarm

 

4

5

6

7

8

9

Switches the appliance (all compartments) between ON and STAND BY (press for three seconds).

Allows switching on and off of only the refrigerator compartment (press for three seconds).

Allows access to the appliance function menu

Using the Up and Down buttons, it is possible to change the set temperature of the refrigerator and navigate through the interactive menu.

It shows the temperature of the refrigerator and freezer compartments, the date and time, Menu functions and visual messages.

By selecting Up/Down the preset temperature can be changed according to the selected function mode (freezer, refrigerator, Fresco-Fresco).

Confirms activation or deactivation of the selections made in the Menu.

Allows activating or deactivating the automatic ice production.

Blinks to signal user alerts such as door left open, also in combination with a sound signal which can be deactivated by pressing the button.

English

Français

9

4 Appliance switching on and off

4.1Switching on and off

First startup When the appliance is connected to the electrical power supply but has not yet been switched on, the display shows the message

This is a safety message to warn that the appliance is connected to the mains, and all the panel buttons are off.

To switch on all the appliance compartments, press the Unit button for three seconds.

Switching off the Refrigerator and Fresco When the appliance is first switched on the TriAction compartment is set compartments to the “freezer” mode. After switching on it remains always on and can

be switched off only by switching off the complete appliance. Press Unit for three seconds.

Restarting Use the same buttons to restart.

The freezer compartment always stays on and cannot be switched off except by completely switching off the appliance by pressing the Unit button for three seconds.

Switching off for long periods

If at the first startup the Standby message does not appear, but another message appears, it means that the appliance has already started the cooling process. If this is the case, deactivate any possible sound signal by pressing the

Alarm button , close the door and wait until the set temperature is reached.

During the first startup, it will not be possible to use the Menu to modify the factory settings until the preset temperature has been reached.

Each time the appliance is switched on it goes trough a self-diagnosis procedure lasting three minutes before completely starting up.

If only the refrigerator compartment or the Fresco compartment is switched off, the specific fan will continue to operate to prevent the formation of unpleasant odors and mold.

Before switching off the appliance for a long period of time, remove all of the items inside and leave the doors and drawers open to prevent the formation of unpleasant odors and mold.

During long absence periods it is recommended to switch off the refrigerator by pressing the Unit button for three seconds and disconnecting the electrical plug or the breaker controlling the socket.

Completely empty the refrigerator, clean and dry it and leave the doors and drawers partially open to prevent unpleasant odors.

10

Appliance switching on and off

4

 

 

How to adjust the temperature for different requirements

4.2

Each model has been carefully tested before leaving the factory and is adjusted in such a way to ensure high performance and low consumption. Usually, it is not necessary to modify the settings.

Nevertheless, according to special needs, it is possible to modify the set temperatures as follows:

Refrigeration Compartment From +1°C to +7°C (from 33,8°F to 44,6°F), the recommended preset temperature is +4°C (39,2°F).

To adjust the temperature use the Up/Down buttons . Upon touching these buttons the newly set temperature will appear in the display. To modify this temperature, use the buttons until reaching the desired temperature.

Fresco-Fresco Compartment

Freezer Compartment

(TriAction)

The temperature shown can vary slightly in respect to the set temperature following frequent openings of the doors or insertion of room temperature foods or large quantities of foods.

6 to 12 hours are necessary to reach the selected temperature.

From -2°C to +2°C (from 28.4°F to 35.6°F), the recommended preset tem-

 

perature is 0°C (32°F).

 

 

 

To adjust the temperature use the Up/Down buttons

. Upon touching

English

these buttons the newly set temperature will appear in the display. To

modify this temperature, use the buttons until reaching the desired tem-

 

perature.

 

 

 

From -13°C to -23°C (from 8,6°F to -9,4°F), the recommended tempera-

 

ture is preset at -18° (0°F).

 

 

 

To adjust the temperature use the Up/Down buttons

. Upon touching

 

these buttons the newly set temperature will appear in the display. To

 

modify this temperature, use the buttons until reaching the desired tem-

 

perature.

 

 

 

In case the compartment is used as refrigerator or Fresco compartment

 

(TriAction function) the recommended and preset temperatures will cor-

 

respond to those indicated for the respective compartments.

 

 

Ice Maker Activation

4.3

Français

 

The Ice Maker button located on the main control panel permits activation of the automatic icemaker. The button is lighted when the icemaker is functioning.

Do not activate the Ice Maker unless the appliance is connected to the water mains.

Information and malfunction messages on the display 4.4

An integrated control system provides information through light signals or text messages visualized on the display.

The information signal is always visualized with a fixed text message, while a malfunction signal is visualized with blinking text. The sound signal that accompanies some malfunction signals can be deactivated by pressing the Alarm button on the main control panel.

The list of malfunction signals is located at the back of this manual.

11

5 Settings and Special Functions

5.1Customization and language settings

To prevent an inadvertent change to the settings the keypad is automatically locked after a certain period of time.

To re-activate the Menu function, press simultaneously the Menu button and the Down button for at least three seconds.

UNIT

FRIDGE

It is possible to customize the functions of your refigerator to adapt it to diverse usage needs, resetting the main parameters (Settings) or activating special functions (Functions).

Functions are accessed on the main display by pressing the Menu button .

The Up/Down buttons permit navigation of the available functions, which can be selected by pressing the Enter button. The display shows the current function status.

Using the Up/Down buttons , it is also possible to scroll through the selected function’s sub-menu if applicable, activating or deactivating by pressing the Enter button .

Once the function is confirmed, the display will automatically step back to the main menu to allow selection of other functions. At any time it is possible to return to the previous selection through the Access button .

The language of the messages appearing on the display can be changed by operating as follows:

Enter the Menu by pressing the Menu button

select Settings via

the Up/Down buttons and confirm via Enter

. Then select the Lan-

guage function and the desired language.

 

5.2Special functions activated through the Menu

To use special functions, select the Menu button and use the Up/Down button to access the menu, confirming the selection .

Shopping Fridge The function lowers the refrigerator temperature to +2°C (35.6°F) for 12 hours, permitting more rapid cooling of food that has just been placed in. Once the 12 hours have expired, the function deactivates automatically, returning to the previously set temperature. It is possible to program a timed activation of the function. After a prolonged interruption of electrical current, it is necessary to reactivate the function.

How to activate

How to deactivate

How to program timed activation

Vacation Fridge

The various Shopping Modes help prepare the cooling, Fridge and TriAction compartments for the introduction of a heat load which can consist of fresh food or other items which may have warmed during transport. The more quickly an item can be cooled or frozen the better it will be preserved.

This mode can also be effective at maintaining compartment temperatures while entertaining when higher than average door and drawer openings are anticipated.

It is possible to program the function with a delay of 1 to 12 hours.

This function (recommended in case of prolonged absences since it allows considerable energy savings) brings the refrigerator compartment temperature to +14°C (57.2°F). It is possible to program the duration, or it can be manually deactivated upon returning after a period of absence. This function remains active even if during the period of absence there is a prolonged interruption of electrical power.

12

Bertazzoni REF30PIXL User Manual

Settings and Special Functions 5

How to activate

How to deactivate upon re-entry

How to program the duration

It is possible to program a period from 1 to 90 days.

Shopping TriAction This function must be activated at least 24 hours before inserting room temperature items into the freezer, or several hours before placing into the freezer previously frozen items which have been subject to a slight temperature rise. This function is automatically deactivated when the programmed time period expires. It is possible o program timed activation of the function.

If interrupted by a prolonged interruption of the electrical power, it is necessary to reactivate the function.

How to activate

How to deactivate

How to program timed activation

It is possible to program the function with a delay of 1 to 12 hours.

Vacation TriAction This function (recommended in case of prolonged absences since it allows considerable energy savings) brings the TriAction compartment temperature to - 18°C (46.4°F). It is possible to program the duration, or it can be manually deactivated upon re-entry after a period of absence.

This function remains active even if during the period of absence there is a prolonged interruption of electrical power.

How to activate

How to deactivate upon re-entry

How to program the duration

It is possible to program a period from 1 to 90 days.

English

Français

13

5 Settings and Special Functions

Bottle Cooler This function can be activated when it is necessary to cool off beverages quickly, by placing them inside the freezer compartment.

It is possible to select a duration of 1 to 45 minutes. A sound signal will indicated when the optimal temperature has been reached. After removing the beverages, deactivate the sound signal by pressing

the Alarm button .

How to activate

How to deactivate

How to program the duration

Ice Maker The IceMaker function permits selecting the size of the ice cubes, by choosing between Large (base setting) or Medium, and activation of the SuperIce function, which increases the quantity of produced ice.

The SuperIce function deactivates automatically after 24 hours.

How to activate the cube size function

How to deactivate

How to activate the SuperIce function

How to deactivate

Sabbath Mode (Optional) The function makes it possible to comply to certain religious observances requiring that the operation of the appliance is not affected by the opening or closing of the doors (the thermostatic control, the inner lighting and the ice maker are deactivated).

How to activate

How to deactivate

14

Settings and Special Functions 5

Water Filter The View Status function permits visualizing the time left before the filter needs to be replaced.

How to check the status of the filter

Reset Filter The Reset Filter function sets to zero the time left before the filter needs to be replaced. It is necessary to set the meter to zero each time the cartridge is replaced.

How to set the filtered water meter to zero

Bypass Filter This function is to be activated when it is not necessary to filter the water, because excellent quality water is already available from the home water system.

How to activate filter Bypass

Manual Clean, Water Filter If ice production has been disabled or unused for a long period it is recommended to perform a Manual Clean function to flush out water which has sat in the system during this period. Repeat the operation until the water is clean.

How to manually clean the filter

Before proceeding it is important to turn off the ice maker by pressing button .

Correctly position the ice tray or another suitable container under the IceMaker to collect water, then close the drawer. At the end of the operation, wash the tray.

English

Français

15

5 Settings and Special Functions

5.3Basic settings of the Menu

TriAction Options

How to set the Fridge function

How to set the Fresco function

How to revert to the Freezer function

Default Setting

How to reset default settings

ATTENTION: If the default settings are restored, the default mode of the TriAction compartment is freezer mode. If it was previously being used in refrigerator or Fresco mode be sure to set it back to your desired setting.

Date

Set Date

How to set the date

Show Date

How to activate the date

How to deactivate the date

Time

Set Time

How to set the time

Select the Menu button and used the Up/Down button to select .

The freezer compartment can, if required, be converted to refrigeration or Fresco-Fresco operating mode.

TriAction

TriAction

TriAction

This offers the possibility to reset default factory settings and cancels any previous changes.

The display will show the date in the format dd:mm:yy (day:month:year), the day will blink. Use the Up/Down buttons to modify the setting, confirm with Enter to go on to the next setting; once the year is confirmed the date will be set.

Using this function it is possible to deactivate/activate the date being shown on the display.

The display shows the hours and minutes in the format hh:mm and with hh: blinking. Use the Up/Down buttons to modify the setting and then confirm by pressing Enter to go on to the next setting.

Once the minutes are confirmed, the time will be set.

16

Internal Layout 5-6

Set 12/24 This function selects the display at 12 or 24 h.

How to set the display to 12 h

How to set the display to 24 h

Show Time Through this function it is possible to activate/deactivate the constant display of the time.

How to activate the time display

How to deactivate

Language The function allows selection of the language for the display messages.

Italian

English

French

German

Spanish

Set °C/°F This function permits showing the temperature in Centigrade or Fahrenheit degrees. Normally, the appliance is set for display in centigrade degrees.

How to set the temperature in Centigrade

How to set the temperature in Fahrenheit

Internal Layout (positioning, adjustment, removal) 6.1

Fresco Drawer Fixed to the slide guides with two thumbscrews.

to remove the drawer, unscrew the thumbscrews and remove the drawer.

TriAction Drawer The upper TriAction can be removed using the same method used for the Fresco drawer

to remove the inner TriAction drawer unscrew the thumbscrews.

When replacing the drawers, make certain the back of the drawers engage under the clips on the slide guides.

English

Français

17

6 Internal Layout

Ice Tray Located in the upper drawer of the freezer compartment

Do not place hands or fingers near the Icemaker when functioning

Shelves

Door Shelves

2

1

after removal, make sure to reposition it correctly - small protrusions from the bottom of the ice bin should align with holes in the upper freezer drawer.

It is recommended that the shelves be emptied prior to adjusting the position. The shelves are sliding and can be easily re-positioned by the user as follows:

release the locking knob by turning it counter-clockwise

support the back of the shelf and tilt up at the front

lift or lower the shelf to the desired position

re-tighten the locking knob

to remove a shelf it is necessary to slide it up to the top

The door shelves can be easily removed for cleaning

Hold the door shelf at the sides and push it upwards to release it from its seat, then pull it outwards.

Reverse the procedure to reinstall.

18

Activation and use of the Ice Maker

7

 

 

Activation and use of the Ice Maker

7.1

 

 

If the ice is not used frequently is advisable to empty the ice bin once every 8-10 days.

It is normal that some ice cubes stick to one another. If the ice is not frequently used, the older cubes can become opaque, and will have a strange flavor and become smaller.

The Icemaker automatically deactivates if the Vacation function is activated.

When the Icemaker is started for the first time, it is recommended to dispose of the first full bin of ice.

If the equipment has been switched off for a month or more, it is recommended to perform a water cleaning cycle. (See section 5: Settings and Special Functions).

The ice maker will only produce ice with the TriAction compartment set to Freezer Mode. The ice maker will continue to operate even when the ice bin is not in position.

Do the ice cubes have an unusual odor?

To activate the Ice Maker after installation of the appliance, press the Icemaker button .

Please note that 12 to 24 hours are necessary before ice production may begin. The production is of 10 cubes per cycle in approximately 10 cycles in 24 hours.

The yield depends on the temperature set in the freezer, the room temperature and the frequency of door opening.

If the appliance is operating without being connected to the water system, make sure that the Icemaker is deactivated by pressing the button .

The Ice Maker produces ice until the ice tray is full and will automatically stop once the maximum level is reached.

With the SuperIce function, it is possible to increase the quantity of ice produced a 24 hours, while the Set Cube Size function permits selection of the size of the produced ice cubes.

At factory default settings Ice Maker can produce approx. 100 ice cubes within 24 hours.

Ice is a porous material which can absorb odors from the environment. Ice cubes which have been in the ice cube container for a long time may absorb odors, stick together and slowly become smaller.

We recommend that old ice cubes not be used. Other means of preventing odors:

The ice cube container should be cleaned occasionally with warm water. Make sure that you switch off the ice maker before clearing the container. Rinse out and wipe dry.

Check the contents of the freezer for spoiled or out-of-date food. All odorous foods should be wrapped thoroughly or stored in airtight containers to prevent the build-up of odors.

The water filter may have to be replaced in some models.

In some cases the quality of the water connection in the house should be checked.

Operating noises

Quite normal noises

Do not place any bottles or food for rapid cooling in the ice cube container. The ice maker may become blocked and be damaged.

Grumbling: refrigerating unit is running. Fan in the recirculating air system is running.

Bubbling, humming or gurgling noises: refrigerant is flowing through the tubes.

Clicking: motor is switching on or off. Solenoid valve on the water connection is opening/closing.

Rumbling: ice cubes are falling into the ice cube container.

Note: the appliance is powered by two independent compressors. It is therefore normal to always have one of two compressors in operation.

English

Français

19

Loading...
+ 47 hidden pages