Bertazzoni PROF365CTXV, PROF305CTXV, PROF244CTXV Installation

Loading...

BERTAZZONI

INSTALLATION MANUAL & USER

GAS COOKTOP

3100534

WWW.BERTAZZONI.COM

/ Table of contents

TABLE OF CONTENTS

INSTALLATON

4

WARNINGS ___________________________________________________________________

4

DATA RATING LABEL ___________________________________________________________

6

BEFORE INSTALLATION ________________________________________________________

6

VENTILATION PREPARATION ____________________________________________________

7

SPECIFICATIONS ______________________________________________________________

7

CLEARENCE DIMENSIONS ______________________________________________________

9

INSTALLATION REQUIREMENTS _________________________________________________

10

Electrical ___________________________________________________________________

10

Gas ________________________________________________________________________

10

ELECTRICAL CONNECTION _____________________________________________________

10

WIRING DIAGRAM _____________________________________________________________

11

GAS CONNECTION _____________________________________________________________

12

Manual shut-o valve _________________________________________________________

12

Flexible connections __________________________________________________________

12

Pressure test-point stopper valve _______________________________________________

12

Pressure regulator ____________________________________________________________

13

INSTALLATION ________________________________________________________________

14

Unpackaging the rangetop_____________________________________________________

14

Installing the worktop frontguard ________________________________________________

14

Installing the island trim _______________________________________________________

15

Installing backguard (optional) __________________________________________________

15

GAS CONVERSION _____________________________________________________________

16

INSTALLATION CHECKLIST ______________________________________________________

18

FINAL PREPARATION ___________________________________________________________

18

BERTAZZONI SERVICE _________________________________________________________

19

USER _______________________________________________________________________

20

WARNINGS ____________________________________________________________________

20

WORKTOP AND KNOBS LAYOUT _________________________________________________

22

GAS COOKTOP ________________________________________________________________

23

ELECTRIC GRIDDLE ____________________________________________________________

25

KEEPING YOUR BERTAZZONI CLEAN _____________________________________________

26

TROUBLESHOOTING ___________________________________________________________

27

TWO YEARS LIMITED WARRANTY ________________________________________________

28

2

/ Models

Models

Models

PROF244CTXV

PROF305CTXV

PROF365CTXV

3

/ Warnings

WARNINGS

To ensure proper and safe operation, the appliance must be properly installed and grounded by a qualified technician. DO NOT attempt to adjust, repair, service, or replace any part of your appliance unless it is specifically recommended in this manual. All other servicing should be referred to a qualified servicer. Have the installer show you the location of the gas shuto valve and how to shut it o in an emergency. A certified technician is required for any adjustments or conversions to Natural or LP gas.

FOR THE INSTALLER: Before installing the Bertazzoni appliance, please read these instructions carefully. This appliance shall be installed in accordance with the manufacturer’s installation instructions.

IMPORTANT: Leave these instructions with the owner, who should save them for local inspector’s use and for future reference. DO NOT remove permanently a xed labels, warnings, or plates from product. This may void the warranty.

Installation must conform with all local codes. In the absence of codes:

United States: installation must conform with the National Fuel Gas Code ANSI Z223.1 INFPA54

Massachusetts: All gas products must be installed by a “Massachusetts” licensed plumber or gasfitter. A “T” type handle manual valve must be installed in the gas supply line to the appliance.

Canada: Installation must be in accordance with the current CAN/CGA B149.1 & 2 Gas Installation codes and/or local codes. Electrical installation must be in accordance with the current CSA C22.1 Canadian Electrical Codes

Part 1 and/or local codes.

This cooktop is NOT designed for installation in manufactured (mobile) homes or recreational park trailers.

DO NOT install this range outdoors.

This appliance must be properly grounded. Grounding reduces the risk of electric shock by providing a safe pathway for electric current in the event of a short circuit.

Warning!

To avoid risk of property damage, personal injury or death; follow information in this manual exactly to prevent a fire or explosion.

WARNING!

If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.

-Do not store or use gasoline or other flammable vapors and liquid in the vicinity of this or any other appliance.

-WHAT TO DO IF YOU SMELL GAS

•Do not try to light any appliance. •Do not touch any electrical switch.

•Do not use any phone in your building. •Immediately call your gas supplier from a neghbor’s phone. Follow the gas supplier’s instructions.

•If you cannot reach your gas suppliers, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or the gas supplier

WARNING!

Never Operate the Top Surface Cooking Section of this Appliance Unattended.

-Failure to follow this warning statement could result in fire, explosion, or burn hazard that could cause property damage. personal injury, or death.

-If a fire should occur, keep away from the appliance and immediately call your fire department.

DO NOT ATTEMPT TO EXTRINGUISH AN OIL/

GREASE FIRE WITH WATER

DANGER!!! ELECTRIC SHOCK HAZARD!!!

To avoid risk of electrical shock, personal injury or death, verify that the appliance has been properly grounded in accordance with local codes or in absence of codes, with the National Electrical Code (NEC). ANSI/NFPA 70latest edition.

DANGER!!! GAS LEAK HAZARD!!!

To avoid risk of personal injury or death, leak-te- sting of the appliance must be conducted according to the manufacturer’s instructions. Before placing appliance in operation, always check for gas leaks with water and soap solution.

DO NOT USE AN OPEN FLAME TO CHECK FOR GAS LEAKS.

4

/ Warnings

WARNING:

Cancer and Reproductiv Harm-

www.P65Warnings.ca.gov.

5

/ Data rating label / Before installation

DATA RATING LABEL

The data rating label shows the model and serial number of the cooktop. It is located under the rangetop and in the last page of this manual.

BEFORE INSTALLATION

This appliance shall only be installed by an authorized professional.

This appliance shall be installed in accordance with the manufacturer’s installation instructions.

This appliance must be installed in accordance with the norms & standards of the country where it will be installed.

The installation of this appliance must conform to local codes and ordinances. In the absence of local codes, Installations must conforms to American National Standards, National Fuel Gas Code ANSI Z223.1 – latest edition/NFPA 54 or B149.1.

The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70.

If local codes permit, a flexible metal appliance connection conduit with the new AGA or CGA certified design, max. 5 feet (1,5 m) long, ½” I.D. is recommended for connecting this appliance to the gas supply line. Do not bend or damage the flexible connector when moving the appliance.

This appliance must be used with the pressure regulator provided.

The regulator shall be properly installed in order to be accessible when the appliance is installed in its final location. The pressure regulator must be set for the type of gas to be used. The pressure regulator has ½” female pipe thread. The appropriate fitting must be determined based on the size of your gas supply line, the flexible metal connector and the shuto valve.

The appliance must be isolated from the gas supply piping system by closing its individual manual shuto valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 PSI (13,8” w.c. or 3,5 kPa).

All opening and holes in the wall and floor, back and under the appliance shall be sealed before installation of the appliance.

A manual valve shall be installed in an accessible location in the gas line external to the appliance for the purpose of turning on or shutting o gas to the appliance.

Type of gas

This cooktop can be used with Natural or LP/Propane gas. The range is shipped from the factory for use with the gas indicated on the rating label positioned on the lower face of the control panel and in the last page of this manual. A step by step conversion procedure is also included in this manual and in each conversion kit.

Gas pressure

The maximum inlet gas supply pressure incoming to the gas appliance pressure regulator is 1/2 PSI (13,8’’ iwc or 3,5 kPa). The minimum gas supply pressure for checking the regulator setting shall be at least 1“ iwc (249 Pa) above the inlet specified manifold pressure to the appliance; this operating pressure is 4” iwc (1.00 kPa) for Natural Gas and 10” iwc (2.50 kPa) for LP Gas.

Room ventilation

An exhaust fan may be used with the appliance; in each case it shall be installed in conformity with the appropriate national and local standards. Exhaust hood operation may a ect other vented appliances; in each case it shall be installed in conformity with the appropriate national and local standards.

Warning

This appliance should not be installed with a ventilation system that directs air in a downward direction toward the range. This type of ventilation system may cause ignition and combustion problems with the appliance resulting in personal injury, property damage, or unintended operation. Ventilating systems that direct the air upwards do not have any restriction.

Do not use aerosol sprays in the vicinity of this appliance while it is in operation.

6

/ Ventilation preparation / Specifications

VENTILATION PREPARATION

This cooktop will best perform when installed with Bertazzoni exhaust hoods. These hoods have been designed to work in conjunction with the Bertazzoni cooktop and have the same finish for a perfect look.

Before installation of the exhaust hood, consult local or regional building and installation codes for additional specific clearance requirements.

Refer to the cooktop hood installation instructions provided by the manufacturer for additional information.

Select Hood and Blower Models:

For wall installations, the hood should be equal or larger width than the cooktop. Where space permits, a hood larger than the range may be desirable for improved ventilation performance.

For island installations, the hood width should overhang the cooktop by a minimum of 3” (76 mm) on each side.

Hood Placement:

For best removal of smoke and odors, the lower edge of the hood should be installed between 25 1/2” (65 cm) and 31 1/2” (80 cm) above the range cooking surface.

If the hood contains any combustible materials (i.e. a wood covering), it must be installed at a minimum of 36” (914 mm) above the cooking surface.

Consider Make-Up Air:

Due to the high volume of ventilation air, a source of outside replacement air is recommended. This is particularly important for tightly sealed and insulated homes. A qualified heating and ventilating contractor should be consulted.

SPECIFICATIONS

A

 

M

 

 

 

 

N

 

P

Q

B

L

 

 

 

 

2”

3/8 (6,1 cm)

 

 

M

 

 

N

3/8 (1cm)

 

 

P

18” 11/16 (47,4 cm)

 

 

Q

1”

1/2 (3,8 cm)

 

H

 

H

 

L

A

B

 

 

 

 

 

PROF244CTXV

23” 3/16 (60,5 cm)

20” 5/8 (52,5 cm)

2” 5/8 (6,6 cm)

6” (15,3 cm)

 

 

 

 

 

 

PROF305CTXV

27”

3/4 (75,5 cm)

20” 5/8 (52,5 cm)

2” 5/8 (6,6 cm)

6” (15,3 cm)

 

 

 

 

 

 

PROF365CTXV

35”

1/8 (89,3 cm)

20” 5/8 (52,5 cm)

2” 5/8 (6,6 cm)

6” (15,3 cm)

 

 

 

 

 

 

7

/ Specifications

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pressure

 

Max Rate

 

 

Min Rate

 

By-pass

 

Burner

 

 

Injector

 

Gas

 

 

 

 

 

 

 

 

 

 

 

 

 

diam.[mm]

Type

[iwc]

[Btu/hr]

[W]

[Btu/hr]

[W]

diam.[mm]

 

 

 

 

 

 

 

 

 

 

 

Auxiliary

0.92

 

NG

4’’

3,750

1,098

900

264

Regulated

 

 

 

0.56

 

LP (Propane)

10’’

3,750

1,098

900

264

0.29

 

Semi-rapid

1.17

 

NG

4’’

6,000

1,729

1,500

439

Regulated

 

 

 

0.73

 

LP (Propane)

10’’

6,300

1,845

1,500

439

0.37

 

Rapid

1.55

 

NG

4’’

10,400

2,046

3,700

1,084

Regulated

 

 

 

0.98

 

LP (Propane)

10’’

11,400

3,339

3,700

1,084

0.58

 

Ultra rapid

1.80

 

NG

4’’

13,600

5,567

5,000

1,464

Regulated

 

 

 

0.98

 

LP (Propane)

10’’

12,300

5,567

5,000

1,464

0.65

 

Dual burner

0.80+1.30

NG

4’’

17,000

4,980

900

264

Regulated

 

 

 

0.50+0.83

LP (Propane)

10’’

18,800

5,507

900

264

0.29/0.65

See use and care manual for the layout of the surface burners of your rangetop

Cabinet Preparation

1.To ensure professional results, the cabinet and countertop openings should be prepared by a qualified cabinet worker.

2.The clearances shown in figure are required.

3.The gas and electrical supply must be located in an area that is accessible without requiring removal of the cooktop. The appliance electrical power cord and gas pipe connection are located on the left rear.

Prepare the finished opening for the rangetop according to dimensions shown in the illustration on the follows page.

The platform must include a cut-out at the right rear for electrical and gas supply connections. It must be level to ensure the cooking surface is level. Refer to the chart below for minimum base support.

8

/ Clearence dimensions

CLEARENCES DIMENSIONS

Installation adjacent to kitchen cabinets

This cooktop may be installed directly adjacent to existing countertop high cabinets (36” or 91.5 cm from the floor).

For the best look, the worktop should be level with the cabinet countertop. This can be accomplished by raising the unit using the adjustment spindles on the legs.

ATTENTION: the cooktop CANNOT be installed directly adjacent to kitchen walls, tall cabinets, tall appliances, or other vertical surfaces above 36” (91.4 cm) high. The minimum side clearance in such cases is 6” (15.2 cm).

Wall cabinets with minimum side clearance must be installed 18” (45.7 cm) above the countertop with countertop height between 35 ½” (90.2 cm) and 37 ¼” (94.6 cm). The maximum depth of wall cabinets above the rangetop shall be 13” (33.0 cm).

Metal hood

B min 25” 1/2 (65 cm)

H min 12” (30,50 cm)

B

H

Cabinet

 

 

Shaded area behind cooktop indicates minimum

 

 

 

 

 

clearance to combustible surfaces, combustible

 

 

 

 

 

materials cannot be located within this area.

 

 

 

 

 

12” (305 mm) min. to combustible surface with

 

 

 

 

 

Flush Island Trim

 

 

 

 

 

For Flush Island installations, counter surface

 

 

 

 

 

should have a cantilever edge meeting the back

 

 

 

 

 

section of the Flush Island Trim accessory.

 

 

 

 

 

As defined in the “National Fuel Gas Code” (ANSI

 

 

 

 

 

Z223.1, Current Edition).

 

 

 

 

 

Clearances from non-combustible materials are

 

 

 

 

 

not part of the ANSI Z21.1

 

 

 

 

 

scope and are not certified by CSA. Clearances of

 

 

 

 

 

less than 12” (305 mm) must be approved by the

 

 

 

 

 

local codes and/or by the local authority having

 

 

 

 

 

jurisdiction.

 

 

 

 

 

 

 

 

 

 

PROF244CTXV

PROF305CTXV

PROF365CTXV

 

 

L1

 

18” 7/8 (48cm)

18” 7/8 (48cm)

18” 7/8 (48cm)

 

 

L2

 

1” 3/16 (3cm)

1” 3/16 (3cm)

1” 3/16 (3cm)

 

 

L3

 

4” (10,2cm)

4” (10,2cm)

4” (10,2cm)

 

 

L4

 

18” (45,7cm)

18” (45,7cm)

18” (45,7cm)

 

 

L5

 

25” 3/16 (64 cm)

25” 3/16 (64 cm)

25” 3/16 (64 cm)

 

 

L6

 

13” (33cm)

13” (33cm)

13” (33cm)

 

 

L7

 

23” 3/16 (60,5cm)

27” 3/4 (75,5cm)

35” 1/8 (89,3 cm)

 

 

 

 

 

 

 

 

 

L8

 

3” 3/8 (8,5cm)

3” 3/8 (8,5cm)

3” 3/8 (8,5cm)

 

 

L9

 

6” 7/8 (17,4cm)

9” 13/16 (24,9cm)

6” 12/16 (17,3cm)

 

 

L10

 

22” 1/16 (56cm)

22” 1/16 (56cm)

33” 1/2 (85cm)

 

 

L11

 

36” (91,5cm)

36” (91,5cm)

36” (91,5cm)

 

9

/ Clearence dimensions

TECHNICAL INSTALLATION INSTRUCTIONS

INSTALLING THE HOB ABOVE AN OVEN

The clearance between the hob and the kitchen furniture or other installed appliances must be enough to ensure su cient ventilation and air discharge.

If installed above an oven, space must be left between the bottom of the hob and the top of the product installed below to allow for ventilation of the entire compartment (see figure).

The oven must be equipped with a cooling device. The manufacturer shall bear no liability in the event of the hob being installed in combination with an oven from another manufacturer.

The countertop must be able to withstand temperatures up to 300°F (149°C).

1” 9/16 (40mm)

INSTALLING THE HOB ABOVE A CUPBOARD OR DRAWERS

The clearance between the hob and the kitchen units must be enough to ensure su cient ventilation and air discharge. If there are other units/furniture (side walls, drawers, etc.), dishwashers or fridges under the hob, a double-layer wooden base must be installed at least 20 mm from the bottom of the hob to avoid any accidental contact. It must only be possible to remove the double-layer base using special tools.

The countertop must be able to withstand temperatures up to 300°F (149°C).

1” 9/16 (40mm)

10

/ Clearence dimensions

HOB FASTENING

In order to prevent accidental water ingress into the unit below, the appliance is fitted with a special gasket.

1)remove the grids, burners and burners caps

2)Turn the hob upside down over a soft surface.

3)Lay the sealing gasket out along the lower edge of the built-in hob after cleaning the mating surface.

4)Turn the hob upside down.

5)Place the hob into the worktop cut-out

6)To fasten the hob to the worktop, use a screwdriver to install the four plates using the corresponding screw in the bottom of the hob.

7)Install the protection carter ( see kit)

8)Position the burners, burners cup and the grids

11

/ Installation requirements / Electrical connection

INSTALLATION REQUIREMENTS

 

ELECTRICAL CONNECTION

ELECTRICAL

A properly-grounded horizontallymounted electrical receptacle should be installed.

Check all local code requirements.

GAS

An agency-approved, properly-sized manual shut- o valve should be installed.

To connect gas between shut-o valve and regulator, use agency-approved, properly sized flexible or rigid pipe. Check all local code requirements.

 

C

 

A

B

D

L1

ELECTRIC

CONNECTION

 

 

GAS INLET

 

L10

 

COOKTOP

COOKTOP

COOKTOP

 

24”

30”

36”

A

1”3/4(45mm)

5”5/8(143mm)

1”7/8(47mm)

B

1”5/8(41mm)

1”5/8(41mm)

1”5/8(41mm)

C

12”1/4(311mm)

15”11/16(399mm)

12”1/4(312mm)

D

1”1/2(38mm)

1”1/2(38mm)

1”1/2(38mm)

L1

18”7/8”(480)

18”7/8”(480)

18”7/8(480mm)

L10

22”1/16(560)

22”1/16(560)

33”7/16(850mm)

 

 

 

 

Warning!

ELECTRICAL SHOCK HAZARD

Disconnect electrical power at the circuit breaker box or fuse box before installing the appliance.

Provide appropriate ground for the appliance. Use copper conductors only.

Failure to follow these instructions could result in serious injury or death.

This unit is manufactured for a polarized, grounded 120 volt/60 Hz, 16 amp system.

Electric power consumption is about 200 W for 36”, 1200W for 48”

The minimum of 102 VAC is required for proper operation of gas ignition systems.

The circuit must be grounded and properly polarized.

The unit is equipped with a SJT power cord and a NEMA 5-15P plug. In case of replacement, the power cord shall be replaced with one of the same type, size and length.

Warning!

Electrical grounding

This appliance is equipped with a three-prong plug for your protection against shock hazard and should be plugged directly into a properly grounded socket. Do not cut or remove the grounding prong from this plug.

Caution

Label all wires prior to disconnecting when servicing controls. Wiring errors can cause improper and dangerous operation.

Verify proper operation after servicing.

For appliances equipped with a cord and plug, do not cut or remove the ground prong. It must be plugged into a matching grounding type receptacle to avoid electrical shock. If there is any doubt as to whether the wall receptacle is properly grounded, the customer should have it checked by a certified electrician.

Do not use an extension cord with the gas cooktop.

Plan the installation so that the power connection is accessible from the front of the cabinet.

12

/ Wiring diagram

WIRING DIAGRAM

The electric wiring diagrams and schematics are attached behind the rangetop, and should not be removed except by a service technician, then replaced after service.

Q

,*1 Q

EL

EL

*

&2/2856

 

 

/(*(1'$

6LPE

'HVFULSWLRQ

 

 

 

6LPE

'HVFULSWLRQ

JU

*UHHQ HDUWK

 

 

,*1

,JQLWLRQ 0LFUR VZLWFKHV

 

 

 

Q

%ODFN OLQH

 

 

 

 

*

6SDUN *HQHUDWRU

 

 

 

EL

:KLWH QHXWUDO

 

 

 

 

 

 

 

 

 

 

 

*9

 

 

 

 

 

 

 

 

 

 

 

0

/

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

13

/ Gas connection

GAS CONNECTION

Warning!

DO NOT USE AN OPEN FLAME WHEN CHECKING FOR LEAKS!

Leak testing of the appliance shall be conducted according to the manufacturer’s instructions. Before placing the oven into operation, always check for leaks with soapy water solution or other acceptable method.

Check for gas leakage with soapy water solution or other acceptable methods in all gas connections installed between inlet gas pipe of the appliance, gas regulator, till to the manual shut-o valve.

All gas connections must comply with national and local codes. The gas supply line (service) must be the same size or greater than the inlet line of the appliance. This cooktop uses a 1/2” NPT inlet (see drawing below for details of gas connection). On all pipe joints use appropriate sealant resistant to gas to joint the adapter to rangetop manifold use only the blue gasket supplied.

If necessary, the appliance must be converted by the dealer, by a factory-trained professional or by a qualified licensed plumber or gas service company.

Gas conversion is important for safe and e ective use of the appliance. It is the responsibility of the dealer and the owner of the cooktop to perform the appropriate gas conversion following the directions of the manufacturer.

THE GAS CONVERSION PROCEDURE IS DESCRIBED IN THIS MANUAL AND IN THE PACKAGE CONTAINING THE CONVERSION NOZZLES SHIPPED WITH EVERY RANGE.

Please provide the service person with this manual before work is started on the range.

MANUAL SHUT-OFF VALVE

THIS VALVE IS NOT SHIPPED WITH THE APPLIANC AND MUST BE SUPPLIED BY THE INSTALLER.

The manual shut-o valve must be installed in the gas service line between the gas hook-up on the wall and the appliance inlet, in a position where it can be reached quickly in the event of an emergency.

In Massachusetts: A ‘T’ handle type manual gas valve must be installed in the gas supply line to this appliance.

FLEXIBLE CONNECTIONS

In case of installation with flexible couplings and/ or quick-disconnect fittings, the installer must use a heavy-duty, AGA design-certified commercial flexible connector of at least 1/2” (1.3 cm) ID NPT (with suitable strain reliefs) in compliance with ANSI Z21.41 and Z21.69 standards.

In Massachusetts: The unit must be installed with a 36” (3-foot) long flexible gas connector.

In Canada: use CAN 1-6.10-88 metal connectors for gas appliances and CAN 1-6.9 M79 quick disconnect device for use with gas fuel.

PRESSURE TEST-POINT STOPPER VALVE

To avoid gas leaks, the pressure test-point stopper valve and gasket supplied with the range must be installed on the gas fitting at the back of the range according to the diagram below.

GAS PIPE

GASKET

GAS CONNECTION ADAPTOR 1/2’’NPT WITH PRESSURE TEST POINT 1/8’’ NPT (TO BE FIXED TOWARD EXTERNAL SIDE OF THE APPLIANCE)

ELBOW

PRESSURE TEST-POINT STOPPER

14

/ Gas connection

PRESSURE REGULATOR

Since service pressure may fluctuate with local demand, every gas cooking appliance must be equipped with a pressure regulator on the incoming service line for safe and e cient operation. The pressure regulator shipped with the appliance has two female threads ½” NPT. The regulator shall be installed properly in order to be accessible when the appliance is installed in its final position.

Manifold pressure should be checked with a manometer and comply with the values indicated below:

Natural gas 4.0” iwc LP/Propane 10.0” iwc

Incoming line pressure upstream from the regulator must be 1” iwc higher than the manifold pressure in order to check the regulator.

The regulator used on this cooktop can withstand a maximum input pressure of 1/2 PSI (13,8” iwc or 3,5 kPa) If the line pressure exceeds that amount, a stepdown regulator is required.

The appliance, its individual shut-o valve, and the pressure regulator must be disconnected from the gas line during any pressure testing of that system at pressures in excess of 1/2 PSI (13,8” iwc or 3,5 kPa).

The individuaL manual shut-o valve must be in the OFF position during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 PSI (13,8” iwc or 3,5 kPa).

Warning

Before carrying out any servicing operation disconnect the appliance from gas and electric supply and extra appliance from final installation place in order to have access to the appliance for proper servicing intervention.

15

/ Installation

INSTALLATION

APPLIANCE INSTALLATION

Unpacking the rangetop

Remove all packing materials from the shipping pallet but leave the adhesive-backed foam layer over brushed-metal surfaces to protect it from scratches until the range is installed in its finalposition. Only the film on the side panels should be removed before inserting the range between the cabinets.

Examine the appliance after unpacking it. In the event of transport damage, do not plug it. Take pictures of the damage and report it immediately to the freight forwarder.

The grates, griddle plate, burner caps, and oven racks should be removed to facilitate

handling.

Appliance Handling Safety

CAUTION

Unit is heavy and requires at least two people or proper equipment to move.

Hidden surfaces may have sharp edges. Use caution when reaching behind or under appliance.

16

/ Gas conversion

GAS CONVERSION

Warning!

Before carrying out this operation, disconnect the appliance from gas and electricity.

Gas conversion shall be conducted by a fac- tory-trained professional.

Call the customer service hotline to identify a fac- tory-trained professional near your home.

The gas conversion procedure for this rangetop includes 4 steps:

Pressure regulator

Surface burners

Visual checks prior to closure of oven bottom panel

Adjustment of minimum setting

The conversion is not completed if all 4 steps have not been concluded properly.

Before performing the gas conversion, locate the package containing the replacement nozzle shipped with every range.

IMPORTANT: Each nozzle has a number indicating its flow diameter printed on the body. Consult the table number 1 for matching nozzles to burners.

Save the nozzles removed from the rangetop for future use.

Step 1: pressure regulator

The pressure regulator supplied with the appliance is a convertible type pressure regulator for use with Natural Gas at a nominal outlet pressure of 4” iwc or LP gas at a nominal outlet pressure of 10”iwc. and it is pre-arranged from the factory to operate with one of these gas/pressure as indicated in the labels a xed on the appliance, package and Instruction booklet.

To convert the regulator for use with the other gas: Unscrew by hand the upper cap of the regulator, remove the white plastic attachment from the cap, reverse its direction and screw it again firmly against the cap. The white plastic attachment has arrows indicating the position for natural gas (NAT) and LP gas (LP).

Screw by hand the metal cap in the original position on the regulator.

LP

NAT

Step 2: surface burners

To replace the nozzles of the surface burners, lift up the burners and unscrew the nozzles shipped with the cooktop using a 7 mm (sochet wrench).

Replace nozzles using the conversion set supplied with the rcooktop or by a Bertazzoni authorized parts warehouse. Each nozzle has a number indicating its flow diameter printed on the body. Consult the table number 1 and matching nozzles to burners.

17

Bertazzoni PROF365CTXV, PROF305CTXV, PROF244CTXV Installation

/ Gas conversion

Step 3: visula checks

Surface burners

The burner flame color should be blue with no yellow on the tips. It is not uncommon to see orange in the

flame color; this indicates the burning of airborne impurities in the gas and will disappear with use. With propane (LP) gas, slight yellow tips on the primary icone are normal.

The flame should burn completely around the burner cap. If it doesn’t, check that the cap is positioned

correctly on the base and that the ports are not blocked.

The flame should be stable with no excessive noise or fluttering.

yellow flames:

further adjustment is required

yellow tips on outer cones: normal for LP gas

soft blue flames: normal for natural gas

After performing all these visual checks, reinstall the bottom panel of the oven compartment and proceed to setting the minimum for each burner.

Step 4: minimum flame adjustment

WARNING!

These adjustments should be made only for use of the appliance with natural gas. For use with liquid propane gas, the choke screw must be fully turned in a clockwise direction.

SURFACE BURNERS

Light one burner at a time and set the knob to the MINIMUM position (small flame).

Remove the knob.

The cooktop is equipped with a safety valve. Using a small-size slotted screwdriver, locate the choke valve on the valve body and turn the choke screw to the right or left until the burner flame is adjusted to desired minimum.

Make sure that the flame does not go out when switching quickly from the MAXIMUM to the MINIMUM position.

For the gas valve of dual burner the choke valve is located on the valve body, the A screw adjust the outer ring, the B screw adjust the inner ring.

A B

High Altitude Installation

Contact customer service for use at altitudes above 2,000 feet (610 meters).

18

+ 42 hidden pages