Bertazzoni HERHK24DW, DW24XV Installation

Loading...

Dishwasher

Installation

Instructions

DW 24XT/DW 24XV

Installation

Instructions

Dishwasher

BEFORE YOU BEGIN

Read these instructions completely and carefully.

IMPORTANTObserve all governing codes and ordinances.

UNote to Installer – Be sure to leave these instructions for the consumer’s and local inspector’s use.

UNote to Consumer – Keep these instructions with your Owner’s Manual for future reference.

USkill Level – Installation of this dishwasher requires basic mechanical and electrical skills. Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the Appliance Warranty.

UCompletion Time – 1 to 3 Hours. New installations require more time than replacement installations.

IMPORTANTThe dishwasher MUST be installed to allow for future removal from the enclosure if service is required.

If you received a damaged dishwasher, you should immediately contact your dealer or builder.

FOR YOUR SAFETY

Read and observe all CAUTIONS and WARNINGS shown throughout these instructions. While performing installations described in this booklet, gloves, safety glasses or goggles should be worn.

WARNING

To reduce the risk of electrical shock, fire, or injury to persons, the installer must ensure that the dishwasher is completely enclosed at the time of installation.

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

If you have an installation problem, contact your dealer or installer. You are responsible for providing adequate electrical, exhausting and other connecting facilities.

PUB NO.29-5955 7/14 MC

Bertazzoni HERHK24DW, DW24XV Installation

Installation Preparation

PARTS SUPPLIED:

Four flat head wood screws to secure dishwasher to underside of countertop (in literature package).

Screw type hose clamps and one drain hose.

2 side mounting clips.

2 top mounting cl ips.

4 Wood Screws

2 Side

2 Top

Screw Type

Drain Hose

Mounting Clips

Mounting Clips

Hose Clamp

 

MATERIALS YOU WILL NEED :

Ferrule, compression nut and 90° Elbow (3/8"NPT external thread on one end, opposite end sized to fit water supply)

Thread seal tape

UL Listed wire nuts (3)

 

Hand

Wire Nuts (3)

90° Elbow,

Shut-Off

Thread

Ferrule and

Valve

Seal Tape

Compression Nut

 

 

Materials For New Installations Only:

Air gap for drain hose, if required

Waste tee for house plumbing, if applicable

Electrical cable or power cord, if applicable

Screw type hose clamps

Strain relief for electrical connection.

Hand shut-off valve

Water line 3/8" min. copper

Coupler for extending drain line, if applicable

Electrical Cable

Hot Water line

(or Power Cord, if applicable)

 

Waste Tee

 

Coupler

 

Screw Type

Strain Relief

Air Gap

Hose Clamps

 

TOOLS YOU WILL NEED:

Phillips head screwdriver

Phillips

5/16" and 1/4" nutdriver

Head

6" Adjustable wrench

Screwdriver

 

Level

Carpenters square

Measuring tape

 

Safety glasses

Flashlight

Flashlight

Bucket to catch water when flushing the line

Gloves

For New Installations Only:

Tubing cutter

Drill and appropriate bits

Bucket

Hole saw set

 

 

Gloves

 

Level

1/4"

 

and 5/16" Nut-

 

driver

 

 

Carpenters

6" Adjustable

Square

Wrench

 

 

Tubing Cutter

 

Measuring Tape

Safety Glasses

 

Drill and Bits

Hole Saw Set

2

Installation Preparation

U The dishwasher must be installed so that drain hose is no more than 10 feet in length for proper drainage.

U The dishwasher must be fully enclosed on the top, sides and back, and must not support any part of the enclosure.

CLEARANCES: When installed into a corner, allow 2" min. clearance between dishwasher and adjacent cabinet, wall or other appliances. Allow 25-5/8" min. clearance from the front of the dishwasher for door opening. Figure B

Countertop

Dishwasher

25-5/8"

Clearance for Door Opening 2" Minimum

UThe rough cabinet opening must be at least 24" deep. The opening should be 35" max. height.

DRAIN REQUIREMENTS

Method 1 – Air Gap with Waste Tee or Disposer

UFollow local codes and ordinances.

UDo not exceed 10 feet distance to drain.

UDo not connect drain lines from other devices to the dishwasher drain hose.

UDishwasher must be connected to waste line with an air gap (not supplied) or 32" minimum high drain loop, depending on local codes and ordinances to prevent back flow into the dishwasher.

UAir gap must be used if waste tee or disposer connection is less than 18" above the floor to prevent siphoning.

DRAIN PREPARATION

The type of drain installation depends on answers to the following questions:

Do local codes or ordinances require an air gap?

Will waste tee or disposer connection be less than 18" above the floor?

Will installation have a drain loop less than 32" above floor?

If the answer to ANY of the 3 questions above is YES, Method 1 MUST be used. Otherwise either Method 1 or Method 2 may be used. Figure C or Figure D.

CAUTION:

An air gap MUST BE USED if the drain hose is connected to waste tee or disposer lower than 18" above the floor.

Failure to provide the proper drain connection height with air gap or 32" minimum, high drain loop will result in improper draining of the dishwasher.

Method 2 – High Drain with Waste Tee or Disposer

Provide a method to attach drain hose to underside of countertop.

18"

32"

Min.

Min.

32"

Min.

18"

Min.

Install waste tee or disposer and air gap according to manufacturer’s instructions.

CABINET PREPARATION

UÊ À Ê>Ê£ £ÉÓ¸Ê` >°Ê iÊ ÊÌ iÊV>L iÌÊÜ> ÊÜ Ì ÊÌ iÊ shaded areas shown in Figure A for the drain hose connection. The hole should be smooth with no sharp edges.

3

+ 9 hidden pages